Search

Freeze-drying, or lyophilization, is widely used to produce pharmaceutical solids that contain temperature-sensitive materials. Herein, using Escherichia coli as a model live organism, whose viability in dry powders is highly sensitive to the water content in the powders, we demonstrated that the drying rate from the frozen thin films generated by thin-film freezing (TFF) is significantly faster than from the bulk frozen solids in conventional shelf freeze-drying. This is likely because the loosely stacked frozen thin films provided a larger solid-air interface and the low thickness of the thin films provided a low mass transfer resistance. The highly porous microstructure and high specific surface area of the thin-film freeze-dried powders may also be related to the faster drying observed. Moreover, we demonstrated that TFF can be applied to produce dry powders of E. coli, a Gram-negative bacterium, or Lactobacillus acidophilus, a Gram-positive bacterium, with minimum bacterial viability loss (i.e., within one log reduction). It is concluded that the TFF technology is promising in accelerating water removal from frozen samples.

Thin-film freeze-drying (TFFD) is a rapid freezing and then drying technique used to prepare inhalable dry powders from the liquid form for drug delivery to the lungs. We report the preparation of aerosolizable dry powders of monoclonal antibodies (mAbs) by TFFD. We first formulated IgG with lactose/leucine (60:40 w/w) or trehalose/leucine (75:25). IgG 1% (w/w) formulated with lactose/leucine (60:40 w/w) in phosphate buffered saline (PBS) (IgG-1-LL-PBS) and processed by TFFD was found to produce the powder with the most desirable aerosol properties. We then replaced IgG with a specific antibody, anti-programmed cell death protein (anti-PD-1 mAb), to prepare a dry powder (anti-PD1-1-LL-PBS), which performed similarly to the IgG-1-LL-PBS powder. The aerosol properties of anti-PD1-1-LL-PBS were significantly better when TFFD was used to prepare the powder as compared to conventional shelf freeze-drying (shelf FD). The dry powder had a porous structure with nanoaggregates. The dry powder had a Tg value between 39-50 °C. When stored at room temperature, the anti-PD-1 mAb in the TFFD powder was more stable than that of the same formulation stored as a liquid. The addition of polyvinylpyrrolidone (PVP) K40 in the formulation was able to raise the Tg to 152 °C, which is expected to further increase the storage stability of the mAbs. The PD-1 binding activities of the anti-PD-1 mAbs before and after TFFD were not different. While protein loss, likely due to protein binding to glass or plastic vials and the TFF apparatus, was identified, we were able to minimize the loss by increasing mAb content in the powders. Lastly, we show that another mAb, anti-TNF-α, can also be converted to a dry powder with a similar composition by TFFD. We conclude that TFFD can be applied to produce stable aerosolizable dry powders of mAbs for pulmonary delivery.

Infections from the SARS-CoV-2 virus have killed over 4.6 million people since it began spreading through human populations in late 2019. In order to develop a therapeutic or prophylactic antibody to help mitigate the effects of the pandemic, a human monoclonal antibody (mAb) that binds to the SARS-CoV-2 spike protein was isolated from a convalescent patient following recovery from COVID-19 disease. This mAb, designated AUG-3387, demonstrates a high affinity for the spike protein of the original viral strains and all variants tested to date. In vitro pseudovirus neutralization and SARS-CoV-2 neutralization activity has been demonstrated in vitro. In addition, a dry powder formulation has been prepared using a Thin-Film Freezing (TFF) process that exhibited a fine particle fraction (FPF) of 50.95 ± 7.69% and a mass median aerodynamic diameter (MMAD) and geometric standard deviation (GSD) of 3.74 ± 0.73 µm and 2.73 ± 0.20, respectively. The dry powder is suitable for delivery directly to the lungs of infected patients using a dry powder inhaler device. Importantly, AUG-3387, administered as a liquid by intraperitoneal injection or the dry powder formulation delivered intratracheally into Syrian hamsters 24 hours after intranasal SARS-CoV-2 infection, demonstrated a dose-dependent reduction in the lung viral load of the virus. These data suggest that AUG-3387 formulated as a dry powder demonstrates potential to treat COVID-19.

Amorphous solid dispersions (ASDs) are a promising formulation approach to improve the solubility, dissolution rate, and bioavailability of poorly water-soluble drugs. ASDs have complicated physicochemical properties due to the various formulations and processes used to produce them. These properties influence their physical stability, so it is important to develop comprehensive and effective characterization techniques for ASDs. Our understanding of the properties of ASDs can be improved through the use of a combination of these techniques. Key factors that affect the properties of ASDs include the glass transition temperature (Tg), molecular mobility, miscibility, and crystallinity. These factors must be evaluated to ensure a stable ASD. In this review, we discuss the most relevant analytical characterization techniques and their applications for the evaluation of ASDs.

Freezing techniques are an essential part of biologics manufacturing processes, yet the formation of ice/water interfaces can impart detrimental effects on proteins. However, the absence of chemical and structural differences between ice and liquid water poses the question as to why ice can destabilize proteins. We hypothesize that the destabilizing stress of the ice-liquid water interface does not originate from the ice-water system itself but rather from the air microbubbles present during the freezing process. As the temperature decreases, the dissolved air is expelled from the ice crystal lattices in the form of microbubbles and is subsequently trapped by the advancing ice front. This newly formed air-water interface represents an additional interfacial area for the proteins to be adsorbed onto and denatured. The result showed that freezing at ∼ 1 K/s led to the formation of small circular microbubbles with diameters ranging from 100 µm to 500 µm. In contrast, slower freezing resulted in the formation of larger, elongated millimeter-size bubbles. The reduction of the number of microbubbles was carried out by the deaeration process using agitation under reduced pressure at 20 kPa. The resulting deaerated (i.e., low dissolved air) protein samples were frozen and monitored for the formation of subvisible aggregates using micro-flow imaging (MFI). The results demonstrated that deaerating the samples prior to intermediate freezing (i.e., TFF) reduced the number of aggregates for both highly surface-active and low surface-active proteins (lactoferrin and bovine IgG, respectively). This reduction was more pronounced in spray freeze drying (SFD) than thin-film freezing (TFF), and less apparent in conventional lyophilization.

Dry powder inhalers (DPIs) are one of the most widely used devices for treating respiratory diseases. Thin--film--freezing (TFF) is a particle engineering technology that has been demonstrated to prepare dry powder for inhalation with enhanced physicochemical properties. Aerosol performance, which is indicated by fine particle fraction (FPF) and mass median aerodynamic diameter (MMAD), is an important consideration during the product development process. However, the conventional approach for formulation development requires many trial-and-error experiments, which is both laborious and time consuming. As a state-of-the art technique, machine learning has gained more attention in pharmaceutical science and has been widely applied in different settings. In this study, we have successfully built a prediction model for aerosol performance by using both tabular data and scanning electron microscopy (SEM) images. TFF technology was used to prepare 134 dry powder formulations which were collected as a tabular dataset. After testing many machine learning models, we determined that the Random Forest (RF) model was best for FPF prediction with a mean absolute error of ± 7.251%, and artificial neural networks (ANNs) performed the best in estimating MMAD with a mean absolute error of ± 0.393 μm. In addition, a convolutional neural network was employed for SEM image classification and has demonstrated high accuracy (83.86%) and adaptability in predicting 316 SEM images of three different drug formulations. In conclusion, the machine learning models using both tabular data and image classification were successfully established to evaluate the aerosol performance of dry powder for inhalation. These machine learning models facilitate the product development process of dry powder for inhalation manufactured by TFF technology and have the potential to significantly reduce the product development workload. The machine learning methodology can also be applied to other formulation design and development processes in the future.

We seek to further addresss the questions posed by Moseson et al. regarding whether any residual crystal level, size, or characteristic is acceptable in an amorphous solid dispersion (ASD) such that its stability, enhanced dissolution, and increased bioavailability are not compromised. To address this highly relevant question, we study an interesting heat- and shear-labile drug in development, LY3009120. To study the effects of residual crystallinity and degradation in ASDs, we prepared three compositionally identical formulations (57–1, 59–4, and 59–5) using the KinetiSol process under various processing conditions to obtain samples with various levels of crystallinity (2.3%, 0.9%, and 0.1%, respectively) and degradation products (0.74%, 1.97%, and 3.12%, respectively). Samples with less than 1% crystallinity were placed on stability, and we observed no measurable change in the drug's crystallinity, dissolution profile or purity in the 59–4 and 59–5 formulations over four months of storage under closed conditions at 25 °C and 60% humidity. For formulations 57–1, 59–4, and 59–5, bioavailability studies in rats reveal a 44-fold, 55-fold, and 62-fold increase in mean AUC, respectively, compared to the physical mixture. This suggests that the presence of some residual crystals after processing can be acceptable and will not change the properties of the ASD over time.

Bacteriophage (phage) therapy has re-gained attention lately given the ever-increasing prevalence of multi-drug resistance 'super-bugs'. To develop therapeutic phage into clinically usable drug products, the strategy of solidifying phage formulations has been implemented to diversify the dosage forms and to overcome the storage condition limitations for liquid phage formulations.In our work, we hypothesize and tested that an advanced technology, thin film freeze-drying (TFFD), can be used to produce phage containing dry powders without significantly losing phage viability. Here we selected T7 phage as our model phage in a preliminary screening study.We found that a binary excipient matrix of sucrose and leucine at ratios of 90:10 or 75:25 by weight, protected phage from the stresses encountered during the TFFD process. In addition, we confirmed that incorporating a buffer system in the formulation significantly improved the survival of phage during the initial freezing step and subsequent sublimation step in the solidifying processes. The titer loss of phage in SM buffer (Tris/NaCl/MgSO4) containing formulation was as low as 0.19 log plaque forming units, which indicated that phage function was well preserved after the TFFD process. The presence of buffers markedly reduced the geometric particle sizes as determined by a dry dispersion method using laser diffraction, which indicated that the TFFD phage powder formulations were easily sheared into smaller powder aggregates, an ideal property for facilitating a variety of topical drug delivery routes including pulmonary delivery through dry powder inhalers, nebulization after reconstitution, and intranasal or wound therapy, etc. CONCLUSION: From these findings, we show that introducing buffer system can stabilize phage during dehydration processes, and TFFD, as a novel particle engineering method, can successfully produce phage containing powders that possess the desired properties for bioactivity and potentially for inhalation therapy.

A bivalent Norovirus vaccine candidate has been developed that contains Norovirus strain GI.1 Norwalk-virus like particles (VLP) and strain GII.4 Consensus VLP adsorbed onto aluminum (oxy)hydroxide. In the present study, we tested the feasibility of converting the vaccine from a liquid suspension into dry powder by thin-film freeze-drying (TFFD). With the proper amount of trehalose and/or sucrose as cryoprotectant, TFFD can be applied to transform the Norovirus vaccine candidate into dry powders without causing antigen loss or particle aggregation, while maintaining the potency of the antigens within a specified acceptable range. In an accelerated stability study, the potency of the antigens was also maintained in the specified acceptable range after the dry powders were stored for eight weeks at 40°C, 75% relative humidity. The dry powder Norovirus vaccine offers the potential to eliminate the cold chain requirement for transport and/or storage of the vaccine.

Gene therapy and more recently, gene editing is attractive via pulmonary delivery for enhanced regional targeting. However, processing of sensitive therapeutics into dry powders for inhalation can be problematic due to relatively stressful spraying or milling steps. Thin-film freeze-drying (TFFD) has attracted attention with its promising application in the production of DPI formulations possessing respirable particle size range (1–5 µm) particularly for thermally or shear sensitive therapeutics. In this study, gene editing dry powder formulations containing PEGylated chitosan/CRISPR-Cas9 nanocomplexes were prepared by TFFD. To evaluate stability during processing, nanocomplex size, zeta potential and transfection efficiency of reconstituted formulations were evaluated, and six potential DPI formulations were identified and characterized in terms of geometric particle size, powder surface morphology, and crystallinity. It was found that two formulations containing 3% mannitol with or without leucine were identified as suitable for inhalation with a desired aerodynamic performance. The flow rate dependency and inhaler dependency of these two formulations were also evaluated at different flow rates (60 L/min and 45 L/min) and different inhaler devices (RS01 DPI and HandiHaler) using NGI testing. This study demonstrated that TFFD processing of CRISPR-Cas9 polymer nanocomplexes resulted in a suitable dry powder for inhalation.

MF59® is an oil-in-water (O/W) nanoemulsion-based vaccine adjuvant that is often used in seasonal and pandemic influenza vaccines. We explored the feasibility of developing dry powders of vaccines adjuvanted with MF59 or AddaVax™, a preclinical grade equivalent of MF59 with the same composition and droplet size as MF59, by thin-film freeze-drying (TFFD). Liquid AddaVax alone was successfully converted to a dry powder by TFFD using trehalose as a stabilizing agent while maintaining the droplet size distribution of AddaVax after it was reconstituted. TFFD was then applied to convert liquid AddaVax-adjuvanted vaccines containing either a model antigen (e.g., ovalbumin) or mono-, bi-, and tri-valent recombinant hemagglutinin (rHA) protein-based H1 and/or H3 (universal) influenza vaccine candidates, as well as the MF59-containing Fluad® Quadrivalent influenza vaccine to dry powders. Both antigens and stabilizing agents affected the physical properties of the vaccines (e.g., mean particle size and particle size distribution) after the vaccines were subjected to TFFD. Importantly, the integrity and hemagglutination activity of the rHA antigens did not significantly change and the immunogenicity of reconstituted influenza vaccine candidates was maintained when evaluated in a mouse model. The vaccine dry powder was not sensitive to repeated freezing-and-thawing, in contrast to its liquid counterpart. It is concluded that TFFD can be applied to convert liquid vaccines containing MF59 or AddaVax to dry powders while maintaining the immunogenicity of the vaccines. Ultimately, TFFD technology may be used to prepare dry powders of multivalent universal influenza vaccines.

In this work, we have developed and tested in vivo a dry powder form of niclosamide made by thin-film freezing (TFF) and administered it by inhalation to rats and hamsters. The niclosamide dry powder, suitable for inhalation, is being developed as a therapeutic agent against COVID-19 infection. Niclosamide, a poorly water-soluble drug, is an interesting drug candidate because it was approved over 60 years ago for use as an anthelmintic medication, but recent studies demonstrated its potential as a broad-spectrum antiviral with a specific pharmacological effect against SARS-CoV-2 infection. In the past, clinical trials for other indications were terminated prior to completion due to low and highly variable oral bioavailability. In order to quickly address the current pandemic, targeting niclosamide directly to the lungs is rational to address the COVID-19 main clinical complications. Thin-film freezing technology was used to develop a niclosamide inhalation powder composition that exhibited acceptable aerosol performance with a fine particle fraction (FPF) of 86.0% and a mass median aerodynamic diameter (MMAD) and geometric standard deviation (GSD) of 1.11 μm and 2.84, respectively. This formulation not only proved to be safe after an acute three-day, multi-dose pharmacokinetic study in rats as evidenced by histopathology analysis, but also was able to achieve lung concentrations above the required IC50 and IC90 levels for at least 24 h after a single administration in a Syrian hamster model. To conclude, we successfully developed a niclosamide dry powder inhalation formulation by thin-film freezing for further scale-up and clinical testing against the COVID-19 infection. This approach overcomes niclosamide’s limitation of poor oral bioavailability by targeting the drug directly to the primary site of infection, the lungs.

We developed an amorphous solid dispersion (ASD) of the poorly water-soluble molecule niclosamide that achieved more than a 2-fold increase in bioavailability. Notably, this niclosamide ASD formulation increased the apparent drug solubility about 60-fold relative to the crystalline material due to the generation of nanoparticles. Niclosamide is a weakly acidic drug, BCS class II, and a poor glass former with low bioavailability in vivo. Hot-melt extrusion is a high-throughput manufacturing method commonly used in the development of ASDs for increasing the apparent solubility and bioavailability of poorly water-soluble compounds. We utilized the polymer polyvinylpyrrolidone–vinyl acetate (PVP–VA) to manufacture niclosamide ASDs by extrusion. Samples were analyzed based on their microscopic and macroscopic behavior and their intermolecular interactions, using DSC, XRD, NMR, FTIR, and DLS. The niclosamide ASD generated nanoparticles with a mean particle size of about 100 nm in FaSSIF media. In a side-by-side diffusion test, these nanoparticles produced a 4-fold increase in niclosamide diffusion. We successfully manufactured amorphous extrudates of the poor glass former niclosamide that showed remarkable in vitro dissolution and diffusion performance. These in vitro tests were translated to a rat model that also showed an increase in oral bioavailability.

Remdesivir dry powder for inhalation was previously developed using thin film freezing (TFF). A single-dose 24-hour pharmacokinetic study in hamsters, a small animal model for SARS-CoV-2, demonstrated that pulmonary delivery of TFF remdesivir can achieve plasma remdesivir and GS-441524 levels higher than the reported EC50s of both remdesivir and GS-441524 (in human epithelial cells) over 20 hours. The half-life of GS-4412524 following dry powder insufflation was about 7 hours, suggesting the dosing regimen would be twice daily administration. Although the remdesivir-Captisol® (80/20 w/w) formulation showed faster and greater absorption of remdesivir and GS-4412524 in the lung, remdesivir-leucine (80/20 w/w) exhibited a greater Cmax with shorter Tmax and lower AUC of GS-441524, indicating lower total drug exposure is required to achieve a high effective concentration against SAR-CoV-2. In conclusion, remdesivir dry powder for inhalation would be a promising alternative dosage form for the treatment of COVID-19 disease.

We developed an amorphous solid dispersion (ASD) of the poorly water-soluble molecule niclosamide that achieved more than a 2-fold increase in bioavailability. Notably, this niclosamide ASD formulation increased the apparent drug solubility about 60-fold relative to the crystalline material due to the generation of nanoparticles. Niclosamide is a weakly acidic drug, BCS class II, and a poor glass former with low bioavailability in vivo. Hot-melt extrusion is a high-throughput manufacturing method commonly used in the development of ASDs for increasing the apparent solubility and bioavailability of poorly water-soluble compounds. We utilized the polymer polyvinylpyrrolidone-vinyl acetate (PVP-VA) to manufacture niclosamide ASDs by extrusion. Samples were analyzed based on their microscopic and macroscopic behavior and their intermolecular interactions, using DSC, XRD, NMR, FTIR, and DLS. The niclosamide ASD generated nanoparticles with a mean particle size of about 100 nm in FaSSIF media. In a side-by-side diffusion test, these nanoparticles produced a 4-fold increase in niclosamide diffusion. We successfully manufactured amorphous extrudates of the poor glass former niclosamide that showed remarkable in vitro dissolution and diffusion performance. These in vitro tests were translated to a rat model that also showed an increase in oral bioavailability. O_FIG_DISPLAY_L [Figure 1] M_FIG_DISPLAY C_FIG_DISPLAY

The aim of this study was to evaluate the benefits of a ternary amorphous solid dispersion (ASD) that was designed as an immediate-release tablet with a high drug load (e.g., 40% w/w) to produce heightened maintenance of drug supersaturation during dissolution testing, which will be henceforth referred to as the "maintenance ability". Ternary ASD granules were produced by hot melt extrusion (HME) and were comprised of itraconazole (ITZ) 50%, hypromellose (HPMC) 20%, and mesoporous silica (XDP) 30%, where amorphous ITZ incorporated into HPMC was efficiently absorbed in XDP pores. The ternary ASD granules containing a high-viscosity HPMC (AF4M) produced a significantly heightened maintenance ability of drug supersaturation in neutral pH dissolution media in which crystalline ITZ solubility is below 1 μg/mL. The final tablet formulation contained 80% w/w of the ASD granules (40% w/w ITZ), had an acceptable size, and exhibited both sufficient tablet hardness and disintegration. The dissolution behavior of the ternary ASD tablet exhibited a supersaturation maintenance ability similar to that of the ASD granules. Under neutral conditions, the ternary ASD tablet showed immediate and higher ITZ release compared with the binary ASD tablets, and this phenomenon could be explained by the difference in ITZ/AF4M particle size in the tablet. In high-resolution scanning electron microscopy (SEM), it was observed that ITZ and AF4M in the ternary formulation could easily form nano-sized particles (

Recent advances in formulation sciences have expanded the previously limited design space for biological modalities, including peptide, protein, and vaccine products. At the same time, the discovery and application of new modalities, such as cellular therapies and gene therapies, have presented formidable challenges to formulation scientists. We explore these challenges and highlight the opportunities to overcome them through the development of novel formulations and drug delivery systems as biological solids. We review the current progress in both industry and academic laboratories, and we provide expert perspectives in those settings. Formulation scientists have made a tremendous effort to accommodate the needs of these novel delivery routes. These include stability-preserving formulations and dehydration processes as well as dosing regimes and dosage forms that improve patient compliance.

Recently, therapeutic uses of bacteriophage (phage) are gaining increased attention, yet common liquid phage formulations require cold chain storage that limits their potential use. Phage therapy is considered as an alternative to antibiotics for bacterial infections and more significantly a promising solution for the ever-increasing prevalence of multi-drug resistance (MDR) pathogens. One of the most promising applications of this therapy is to treat pulmonary bacterial infections. To efficiently deliver therapeutic phage to the lungs, phage formulations that allow for nebulization or dry powder inhalation are under active development. Several conventional particle engineering technologies have been applied in the development of dry powder inhalers (DPI), including spray drying, spray freeze drying, and atmospheric spray freeze drying, but these processes have their own disadvantages that limit their use with bacteriophage formulations and delivery. In our work, we hypothesize that thin film freeze-drying (TFFD) can be used to produce brittle matrix powders containing phage that may be suitable for delivery by several routes of administration, including by nebulization after reconstitution and by intranasal or inhalation delivery of the resulting dry powder. Here we selected T7 bacteriophage as our model phage in a preliminary screening study and found that a binary excipient matrix of sucrose and leucine at ratios of 80:20 or 75:25 by weight, protected bacteriophage from the stresses encountered during the TFFD process. In addition, we confirm that incorporating a buffer system during the TFFD process significantly improved the survival of phage during the ultra-rapid freezing step of the TFFD process and subsequent sublimation step in the lyophilization process. This preservation of phage bioactivity was significantly better than that observed for formulations without a buffer system. The titer loss of phage in standard SM buffer (Tris/NaCl/MgSO4/gelatin) containing formulation was as low as 0.2 log plaque forming units (pfu), which indicates that phage functionality was preserved after the TFFD process. Moreover, the presence of buffers markedly reduced the geometric particle sizes as determined by a dry dispersion method using laser diffraction, which indicates that the TFFD phage powder formulations were easily sheared into smaller powder aggregates, an ideal property for facilitating pulmonary delivery through DPIs. From these findings, we show that TFFD is a particle engineering method that can successfully produce phage containing powders that possess the desired properties for bioactivity and inhalation therapy.

Thermal processing has gained much interest in the pharmaceutical industry, particularly for the enhancement of solubility, bioavailability, and dissolution of active pharmaceutical ingredients (APIs) with poor aqueous solubility. Formulation scientists have developed various techniques which may include physical and chemical modifications to achieve solubility enhancement. One of the most commonly used methods for solubility enhancement is through the use of amorphous solid dispersions (ASDs). Examples of commercialized ASDs include Kaletra®, Kalydeco®, and Onmel®. Various technologies produce ASDs; some of the approaches, such as spray-drying, solvent evaporation, and lyophilization, involve the use of solvents, whereas thermal approaches often do not require solvents. Processes that do not require solvents are usually preferred, as some solvents may induce toxicity due to residual solvents and are often considered to be damaging to the environment. The purpose of this review is to provide an update on recent innovations reported for using hot-melt extrusion and KinetiSol® Dispersing technologies to formulate poorly water-soluble APIs in amorphous solid dispersions. We will address development challenges for poorly water-soluble APIs and how these two processes meet these challenges.

The dire need for safe and effective coronavirus disease (COVID-19) vaccines is met with many vaccine candidates being evaluated in pre-clinical and clinical studies. The COVID-19 vaccine candidates currently in phase 3 or phase 2/3 clinical trials as well as those that recently received emergency use authorization (EUA) from the United States Food and Drug Administration (FDA) and/or other regulatory agencies worldwide require either cold (i.e., 2-8°C) or even freezing temperatures as low as -70°C for storage and distribution. Thus, existing cold chain will struggle to support both the standard national immunization programs and COVID-19 vaccination. The requirement for cold chain is now a major challenge towards worldwide rapid mass vaccination against COVID-19. In this commentary, we stress that thermostabilizing technologies are available to enable cold chain-free vaccine storage and distribution, as well as potential needle-free vaccination. Significant efforts on thermostabilizing technologies must now be applied on next-generation COVID-19 vaccines for more cost-effective worldwide mass vaccination and COVID-19 eradication.

The purpose of this study was to improve the bioavailability of carbamazepine (CBZ), a poorly water-soluble antiepileptic drug, via modified-release amorphous solid dispersions (mr-ASD) by a thin film freezing (TFF) process. Three types of CBZ-mr-ASD with immediate-, delayed-, and controlled-release properties were successfully prepared with HPMC E3 (hydrophilic), L100-55 (enteric), and cellulose acetate (CA, lipophilic), defined as CBZ-ir-ASD, CBZ-dr-ASD, and CBZ-cr-ASD, respectively. A dry granulation method was used to prepare CBZ-mr-ASD capsule formulations. Various characterization techniques were applied to evaluate the physicochemical properties of CBZ-mr-ASD and the related capsules. The drug remained in an amorphous state when encapsulated within CBZ-mr-ASD, and the capsule formulation progress did not affect the performance of the dispersions. In dissolution tests, the preparations and the corresponding dosage forms similarly showed typical immediate-, delayed-, and controlled-release properties depending on the solubility of the polymers. Moreover, single-dose 24 h pharmacokinetic studies in rats indicated that CBZ-mr-ASD significantly enhanced the oral absorption of CBZ compared to that of crude CBZ. Increased oral absorption of CBZ was observed, especially in the CBZ-dr-ASD formulation, which showed a better pharmacokinetic profile than that of crude CBZ with 2.63- and 3.17-fold improved bioavailability of the drug and its main active metabolite carbamazepine 10,11-epoxide (CBZ-E).

Aluminum salts are used as an adjuvant in many human and veterinary vaccines. However, aluminum salt-adjuvanted vaccines are sensitive to temperature change and must be stored at 2-8 °C. Inadvertently exposing them to slow freezing temperatures can cause irreversible aggregation of aluminum salt microparticles and loss of potency and/or immunogenicity of the vaccines. There have been efforts to overcome this limitation by either adding stabilizing agents to the liquid vaccine or converting the vaccine from a liquid to a dry powder. Thin-film freeze-drying (TFFD) has proven to be an effective process to convert aluminum salt-adjuvanted vaccines from liquid to dry powder without causing particle aggregation or loss of immunogenicity upon reconstitution. This chapter provides a review of the TFFD process and examples for preparing stable aluminum salt-adjuvanted vaccine dry powders using TFFD.

Aluminum salts are used as an adjuvant in many human and veterinary vaccines. However, aluminum salt-adjuvanted vaccines are sensitive to temperature change and must be stored at 2-8 °C. Inadvertently exposing them to slow freezing temperatures can cause irreversible aggregation of aluminum salt microparticles and loss of potency and/or immunogenicity of the vaccines. There have been efforts to overcome this limitation by either adding stabilizing agents to the liquid vaccine or converting the vaccine from a liquid to a dry powder. Thin-film freeze-drying (TFFD) has proven to be an effective process to convert aluminum salt-adjuvanted vaccines from liquid to dry powder without causing particle aggregation or loss of immunogenicity upon reconstitution. This chapter provides a review of the TFFD process and examples for preparing stable aluminum salt-adjuvanted vaccine dry powders using TFFD.

Amorphous solid dispersion (ASD) is commonly used in pharmaceutical industry. It has been mainly employed to enhance the oral bioavailability of poorly water-soluble drugs that belong to class II and IV of the biopharmaceutical classification system but has showed promise in other areas of pharmaceutical research. In this review, the potential and limitations of ASD dry powder for inhalation are discussed. ASD powder for inhalation (ASD-IP) is commonly prepared by spray drying technique. The physicochemical characteristics of ASD-IP could be tailored to achieve effective lung deposition. ASD-IP could also attain rapid dissolution behavior to achieve therapeutically effective concentration either locally or systemically before particle clearance in the lung. The key challenges of using ASD powder for inhalation include the possible chemical and/or physical instability of the amorphous phase during manufacturing and in vivo, and the moisture and temperature sensitivity of ASD-IP that affects its storage stability.

We report for the first time that incorporation of a thermally conductive excipient (TCE) modifies the thermal conductivity of the ternary drug-polymer-TCE compositions such that high-energy mixing can occur for prolonged periods at a selected steady-state temperature during the KinetiSol process. In this study, candurin, a TCE, is incorporated within a composition that is processed by high-energy mixing from the KinetiSol process to increase the thermal conductivity of the ternary composition. The improved thermal conductivity promotes heat transfer and enables the high-energy mixing applied during the KinetiSol process to be continued for prolonged time intervals at a selected steady-state temperature, instead of undergoing a continued increase in temperature when the TCE is not present in the composition. The addition of candurin does not impact the molecular structure and mixing of the drug and polymer in ASDs from solid-state NMR characterizations. Compositions with candurin achieved a steady-state processing temperature with + 5°C of the target temperature, and these compositions demonstrated the ability to mix for prolonged time periods while maintaining within this steady-state temperature range, thus enabling the formation of an ASD at a temperature that the drug does not chemically degrade. This study demonstrated that inclusion of the TCE modified the composition’s thermal conductivity to efficiently dissipate heat to achieve a selected steady-state temperature during the KinetiSol process, thus providing prolonged mixing times at a lower temperature for dissolving the drug into the polymer to achieve an ASD without sacrificing product performance.

In the race for a safe and effective vaccine against coronavirus disease (COVID)-19, pharmaceutical formulation science plays a critical role throughout the development, manufacturing, distribution, and vaccination phases. The proper choice of the type of vaccine, carrier or vector, adjuvant, excipients, dosage form, and route of administration can directly impact not only the immune responses induced and the resultant efficacy against COVID-19, but also the logistics of manufacturing, storing and distributing the vaccine, and mass vaccination. In this review, we described the COVID-19 vaccines that are currently tested in clinical trials and provided in-depth insight into the various types of vaccines, their compositions, advantages, and potential limitations. We also addressed how challenges in vaccine distribution and administration may be alleviated by applying vaccine-stabilization strategies and the use of specific mucosal immune response-inducing, non-invasive routes of administration, which must be considered early in the development process.

Solid-state NMR (ssNMR) analysis of pharmaceutical materials relies on accurate resonance assignments. The relatively low sensitivity and resolution from the natural abundance and solid-state nature of the active pharmaceutical ingredient (API) and particularly the disordered structure of amorphous forms result in the ambiguous identification of NMR peaks. In this study, a robust protocol for unambiguously assigning 13C and 1H chemical shifts of crystalline and amorphous APIs has been established and successfully tested on γ-polymorph indomethacin. Specifically, one-dimensional (1D) 13C-edited experiments, two-dimensional (2D) 13C-detected homo- and heteronuclear correlations, and 2D 1H-detected techniques under ultrafast magic angle spinning (MAS) provide enhanced resolution to identify overlapped 13C resonances and assign confidently the 1H chemical shifts. This experimental strategy allows us to assign particularly those carbons and protons either unassigned or ambiguous identified due to the technical challenges in previous literature. Besides, the chemical shift comparison between the crystalline and amorphous forms can potentially report the molecular packing variations.

Hydrophobic and hydrophilic thermoplastic poly(urethane) (TPU) mixtures offer the opportunity to tune water swelling capacity and diffusion rate for drugs exhibiting broadly different properties. We sought to (1) assess the range of drug diffusion rates achieved by varying hydrophilic-to-hydrophobic TPU ratio relative to varying ethylene vinyl acetate (EVA) crystallinity; (2) investigate the effect of mixture ratio on permeability of emtricitabine; and (3) investigate the impact of the extrusion process on mixing of the two TPUs and the resulting impact on drug diffusion. The permeability of water-soluble emtricitabine exhibited a 736-fold range across the blends of TPU, but only a 3.4-fold range across the EVA grades investigated. Varying hydrophilic content of the TPU mixture from 0% to 25% (w/w) led to a negligible permeability change, while changing hydrophilic content from 55% to 100% resulted in a linear 3-fold increase in drug permeability. Interestingly, an 123-fold permeability change occurred between 50% and 55% hydrophilic polymer. Extrusion process parameters exhibited minimal impact on homogeneity and drug diffusion. These findings suggest that hydrophilic polymer domains form a continuous network at levels above 55% hydrophilic TPU, thus facilitating a water-filled porous network when exposed to water that provides a mechanism for accelerated drug diffusion.

We investigated the feasibility of preparing high-potency tacrolimus dry powder for inhalation using thin film freezing (TFF). We found that using ultra-rapid freezing can increase drug loading up to 95% while maintaining good aerosol performance. Drug loading affected the specific surface area and moisture sorption of TFF formulations, but it did not affect the chemical stability, physical stability, and dissolution of tacrolimus. Tacrolimus remained amorphous after storage at 40 °C/75% RH, and 25 °C/60% RH for up to 6 months. Lactose functioned as a bulking agent, and it had little to no effect as a stabilizer for amorphous tacrolimus due to a lack of interaction between the drug and excipient. Additionally, the aerosol performance of TFF tacrolimus/lactose (95/5) did not significantly change after six months of storage at 25 °C/60% RH. For processing parameters, the solids content and the processing temperature did not affect the aerosol performance of tacrolimus. Furthermore, both low- and high-resistance RS01 showed optimal and consistent aerosol performance over the 1–4 kPa pressure drop range. In conclusion, TFF is a suitable technology for producing inhalable powder that contain high drug loading and have less flow rate dependence.

Abiraterone is a poorly water-soluble drug. It has a high melting point and limited solubility in organic solvents, making it difficult to formulate as an amorphous solid dispersion (ASD) with conventional technologies. KinetiSol&reg, is a high-energy, fusion-based, solvent-free technology that can produce ASDs. The aim of this study was to evaluate the application of KinetiSol to make abiraterone ASDs. We developed binary KinetiSol ASDs (KSDs) using both polymers and oligomers. For the first time, we reported that KinetiSol can process hydroxypropyl-&beta, cyclodextrin (HPBCD), a low molecular-weight oligomer. Upon X-ray diffractometry and modulated differential scanning calorimetry analysis, we found the KSDs to be amorphous. In vitro dissolution analysis revealed that maximum abiraterone dissolution enhancement was achieved using a HPBCD binary KSD. However, the KSD showed significant abiraterone precipitation in fasted state simulated intestinal fluid (FaSSIF) media. Hence, hypromellose acetate succinate (HPMCAS126G) was selected as an abiraterone precipitation inhibitor and an optimized ternary KSD was developed. A pharmacokinetic study revealed that HPBCD based binary and ternary KSDs enhanced abiraterone bioavailability by 12.4-fold and 13.8-fold, respectively, compared to a generic abiraterone acetate tablet. Thus, this study is the first to demonstrate the successful production of an abiraterone ASD that exhibited enhanced dissolution and bioavailability.

Amorphous solid dispersions (ASDs) are commonly used in the pharmaceutical industry to improve the dissolution and bioavailability of poorly water-soluble drugs. Hot melt extrusion (HME) has been employed to prepare ASD based products. However, due to the narrow processing window of HME, ASDs are normally obtained with high processing temperatures and mechanical stress. Interestingly, one-third of pharmaceutical compounds reportedly exist in hydrate forms. In this study, we selected carbamazepine (CBZ) dihydrate to investigate its solid-state changes during the dehydration process and the impact of the dehydration on the preparation of CBZ ASDs using a Leistritz micro-18 extruder. Various characterization techniques were used to study the dehydration kinetics of CBZ dihydrate under different conditions. We designed the extrusion runs and demonstrated that: 1) the dehydration of CBZ dihydrate resulted in a disordered state of the drug molecule, 2) the resulted higher energy state CBZ facilitated the drug solubilization and mixing with the polymer matrix during the HME process, which significantly decreased the required extrusion temperature from 140 to 60 &deg, C for CBZ ASDs manufacturing compared to directly processing anhydrous crystalline CBZ. This work illustrated that the proper utilization of drug hydrates can significantly improve the processability of HME for preparing ASDs.

Intranasal vaccination using dry powder vaccine formulation represents an attractive, non-invasive vaccination modality with better storage stability and added protection at the mucosal surfaces. Herein we report that it is feasible to induce specific mucosal and systemic antibody responses by intranasal immunization with a dry powder vaccine adjuvanted with an insoluble aluminum salt. The dry powder vaccine was prepared by thin-film freeze-drying of a model antigen, ovalbumin, adsorbed on aluminum (oxy)hydroxide as an adjuvant. Special emphasis was placed on the characterization of the dry powder vaccine formulation that can be realistically used in humans by a nasal dry powder delivery device. The vaccine powder was found to have passable to good flow properties, and the vaccine was uniformly distributed in the dry powder. An in vitro nasal deposition study using nasal casts of adult humans showed that around 90% of the powder was deposited in the nasal cavity. Intranasal immunization of rats with the dry powder vaccine elicited a specific serum antibody response as well as specific IgA responses in the nose and lung secretions of the rats. This study demonstrates, for the first time, the generation of systemic and mucosal immune responses by intranasal immunization using a dry powder vaccine adjuvanted with an aluminum salt.

There is currently no in vitro technique for assessing plume geometry of nasal sprays under airflow conditions. However, a majority of FDA approved nasal products recommend that patients inhale during actuation. Therefore, a reproducible in vitro test that measures plume angles under physiologically relevant inhalation flow rates would be useful. The purpose of this study was to adapt the recently described Plume Induction Port Evaluator (PIPE) apparatus for nasal sprays under flow and correlate these with nasal cast deposition patterns. Mass Median Plume Angles (MMPAs) of four nasal spray formulations with increasing viscosities were determined using the PIPE apparatus in the absence and presence of airflow. MMPAs were then correlated to drug deposition within 3D printed nasal casts using airflow. We evaluated different inhalation instructions obtained from the package insert of nasal products. MMPAs significantly reduced (narrower angles) when using flow for the three formulations with the lowest viscosities. An increase in the turbinate deposition was observed in the nasal casts when just one of the nostrils was closed during inhalation, except by the highest viscosity formulation. The turbinate deposition numerically correlated with changes in the plume angles observed using PIPE.

Single-chain tissue-type plasminogen activator (sctPA) and single-chain urokinase plasminogen activator (scuPA) have attracted interest as enzymes for the treatment of inhalational smoke-induced acute lung injury (ISALI). In this study, the pulmonary delivery of commercial human sctPA and lyophilized scuPA and their reconstituted solution forms were demonstrated using vibrating mesh nebulizers (Aeroneb® Pro (active) and EZ Breathe® (passive)). Both the Aeroneb® Pro and EZ Breathe® vibrating mesh nebulizers produced atomized droplets of protein solution of similar size of less than about 5 μm, which is appropriate for pulmonary delivery. Enzymatic activities of scuPA and of sctPA were determined after nebulization and both remained stable (88.0% and 93.9%). Additionally, the enzymatic activities of sctPA and tcuPA were not significantly affected by excipients, lyophilization or reconstitution conditions. The results of these studies support further development of inhaled formulations of fibrinolysins for delivery to the lungs following smoke-induced acute pulmonary injury.

Due to the high number of poorly soluble drugs in the development pipeline, novel processes for delivery of these challenging molecules are increasingly in demand. One such emerging method is KinetiSol, which utilizes high shear to produce amorphous solid dispersions. The process has been shown to be amenable to difficult to process active pharmaceutical ingredients with high melting points, poor organic solubility, or sensitivity to heat degradation. Additionally, the process enables classes of polymers not conventionally processable due to their high molecular weight and/or poor organic solubility. Beyond these advantages, the KinetiSol process shows promise with other applications, such as the production of amorphous mucoadhesive dispersions for delivery of compounds that would also benefit from permeability enhancement.

Vemurafenib is a poorly soluble, low permeability drug that has a demonstrated need for a solubility-enhanced formulation. However, conventional approaches for amorphous solid dispersion production are challenging due to the physiochemical properties of the compound. A suitable and novel method for creating an amorphous solid dispersion, known as solvent-controlled coprecipitation, was developed to make a material known as microprecipitated bulk powder (MBP). However, this approach has limitations in its processing and formulation space. In this study, it was hypothesized that vemurafenib can be processed by KinetiSol into the same amorphous formulation as MBP. The KinetiSol process utilizes high shear to rapidly process amorphous solid dispersions containing vemurafenib. Analysis of the material demonstrated that KinetiSol produced amorphous, single-phase material with acceptable chemical purity and stability. Values obtained were congruent to analysis conducted on the comparator material. However, the materials differed in particle morphology as the KinetiSol material was dense, smooth, and uniform while the MBP comparator was porous in structure and exhibited high surface area. The particles produced by KinetiSol had improved in-vitro dissolution and pharmacokinetic performance for vemurafenib compared to MBP due to slower drug nucleation and recrystallization which resulted in superior supersaturation maintenance during drug release. In the in-vivo rat pharmacokinetic study, both amorphous solid dispersions produced by KinetiSol exhibited mean AUC values at least two-fold that of MBP when dosed as a suspension. It was concluded that the KinetiSol process produced superior dosage forms containing vemurafenib with the potential for substantial reduction in patient pill burden.

The use of amorphous solid dispersions (ASD) to overcome poor drug solubility has gained interest in the pharmaceutical industry over the past decade. ASDs are challenging to formulate because they are thermodynamically unstable, and the dispersed drugs tend to recrystallize. Until now, most research on ASDs has focused on immediate-release formulations, supersaturation, and stability; only a few studies have recently reported on the manufacturing of sustained-release ASDs. Sustained-release ASDs can minimize the frequency of administration and prevent high concentrations that can lead to toxicity. Sustained-release ASDs can also decrease the reprecipitation rate in the medium, which can lead to increased bioavailability. However, sustained-release ASDs also pose some significant challenges, such as intramatrix recrystallization, inhibition of drug release as a result of drug-polymer gelling, and low supersaturation due to a slow dissolution rate. This review details the challenges and the formulation approaches that have been investigated to manufacture sustained-release ASDs. In particular, the advantages and drawbacks of hydrophilic polymers, hydrophobic polymers, and lipid-based systems are discussed.

Effective targeting of nasal spray deposition could improve local, systemic, and CNS drug delivery; however, this has proven to be difficult due to the anatomical features of the nasal cavity, including the nasal valve and turbinate structures. Furthermore, nasal cavity geometries and dimensions vary between individuals based on differences in their age, gender, and ethnicity. The effect of patient-specific administration parameters was evaluated for their ability to overcome the barriers of targeted nasal drug delivery. The nasal spray deposition was evaluated in 10 3D-printed nasal cavity replicas developed based on the CT-scans of five pediatric and five adult subjects. Cromolyn sodium nasal solution, USP, modified with varying concentrations of hypromellose was utilized as a model nasal spray to evaluate the deposition pattern from formulations producing a variety of plume angles. A central composite design of experiments was implemented using the formulation with the narrowest plume angle to determine the patient-specific angle for targeting the turbinate region in each individual. The use of the patient-specific angle with this formulation significantly increased the turbinate deposition efficiency compared to that found for all subjects using an administration angle of 30°, around 90% compared to about 73%. Generally, we found turbinate deposition increased with decreases in the administration angle. Deposition to the upper regions of the replica was poor with any formulation or administration angle tested. Effective turbinate targeting of nasal sprays can be accomplished with the use of patient-specific administration parameters in individuals. Further research is required to see if these parameters can be device-controlled for patients and if other regions can be effectively targeted with other nasal devices.

The focus of our study was to employ a solvent-free, thermal process to evaluate the use of a porous carrier in a drug-polymer-porous carrier ternary formulation containing a high drug load (e.g., ≥50% w/w). The purpose of the study was to improve the dissolution properties of the biopharmaceutical classification system class II drug, indomethacin, in the ternary formulation. The effect that the selected polymer has on properties of the formulation was studied, and the formulation characteristics of hypromellose (AF15), copovidone (VA64), and polyvinyl alcohol-polyethylene glycol graft copolymer was evaluated to understand differences in dissolution rates and drug adsorption onto the porous carrier. The ternary formulations were manufactured using a thermal technique that relied on heating and mixing, without the necessity of mechanical shear. All thermally processed granules that employed the porous carrier exhibited immediate release compared with crystalline indomethacin and physical mixtures. In addition, the ternary formulations maintained supersaturation compared with the binary formulations without polymer. The results of this study indicated that the thermally processed ternary formulations containing a porous carrier demonstrated a much improved dissolution profile in nonsink conditions.

A bivalent Norovirus vaccine candidate has been developed that contains Norovirus strain GI.1 Norwalk-virus like particles (VLP) and strain GII.4 Consensus VLP adsorbed on aluminum (oxy)hydroxide. The Norwalk and Consensus antigens have different stability profiles, making it challenging to prepare a dry powder form of the Norovirus vaccine while maintaining the potency of both antigens. In the present study, we tested the feasibility of converting the vaccine from a liquid suspension to dry powders by thin-film freeze-drying (TFFD). With the proper amount of trehalose and/or sucrose as cryoprotectant (i.e. sucrose alone at 4.55% or 5.55%, w/v, or trehalose at 3–4% with 0.55% of sucrose), TFFD can be applied to successfully convert the Norovirus vaccine candidate into dry powders without causing antigen loss or particle aggregation, while maintaining the relative potency of both antigens within a specified acceptable range. In an accelerated stability study, the potency of the antigens was also maintained in the specified acceptable range after the dry powders prepared by TFFD in the presence of 5.55% (w/v) of sucrose were stored for eight weeks at 40 °C, 75% relative humidity. It is concluded that it is feasible to apply TFFD to convert the Norovirus vaccine from a liquid suspension to stable dry powders.

The study of amorphous solid dispersions (ASDs) is currently one of the most exciting areas in pharmaceutics. Research has shown that ASDs offer unique advantages in improving the bioavailability of poorly water-soluble drugs over conventional delivery systems. The various formulations and manufacturing processes of ASDs affect their physicochemical stability, processability, and drug release characteristics. Therefore, the characterization of ASDs is critical in all stages of product development, including preformulation screening, formulation development, process scale-up, and commercial manufacturing. Proper characterization allows for the rational selection of formulation composition and manufacturing processing methods and allows for high-quality drug products. In this review, we present the most commonly used methods for characterizing the solid-state properties of ASDs, and we discuss their mechanisms, applications, advantages, and disadvantages. We also provide a brief overview of the methods used to characterize ASDs behavior in aqueous media. These methods are divided into three different categories: microscopic and surface analysis methods, thermal analysis methods, and spectroscopic methods. In addition, this article discusses a number of emerging techniques. Last, we discuss how these methods are applied at different stages in the ASDs product development life cycle.

The use of amorphous solid dispersions to improve the bioavailability of active ingredients from the BCS II and IV classifications continues to gain interest in the pharmaceutical industry. Over the last decade, methods for generating amorphous solid dispersions have been well established in commercially available products and in the literature. However, the amorphous solid dispersions manufactured by different technologies differ in many aspects, primarily chemical stability, physical stability, and performance, both in vitro and in vivo. This review analyzes the impact of manufacturing methods on those properties of amorphous solid dispersions. For example, the chemical stability of drugs and polymers can be influenced by differences in the level of thermal exposure during fusion-based and solvent-based processes. The physical stability of amorphous content varies according to the thermal history, particle morphology, and nucleation process of amorphous solid dispersions produced by different methods. The in vitro and in vivo performance of amorphous formulations are also affected by differences in particle morphology and in the molecular interactions caused by the manufacturing method. Additionally, we describe the mechanism of manufacturing methods and the thermodynamic theories that relate to amorphous formulations.

The oral delivery of mucoadhesive patches has been shown to enhance the absorption of large molecules such as peptides. We hypothesized that this mechanism could have utility for poorly soluble small molecules by utilizing a mucoadhesive polymer as the matrix for an amorphous solid dispersion. Binary dispersions of itraconazole and carbomer (Carbopol 71G) were prepared utilizing a thermokinetic mixing process (KinetiSol Dispersing) and the physicochemical properties were investigated by powder X-ray diffraction, calorimetry, and liquid chromatography. Adhesion of the dispersions to freshly excised porcine intestine was investigated with a texture analyzer. Minitablets were compressed from the optimal dispersion and further investigated in vitro and in vivo in rats. Thermokinetic mixing successfully processed amorphous dispersions up to 30% drug loading and each dispersion exhibited works of adhesion that were approximately an order of magnitude greater than a negative control in vitro. Ethylcellulose (EC) coated and uncoated minitablets prepared with the 30% drug load dispersion were delivered orally to rats and exhibited sustained release characteristics, with overall bioavailability greater for the uncoated minitablets compared to the EC-coated minitablets, similar to the rank order observed in our in vitro dissolution experiments. Necropsy studies showed that minitablets delivered with enteric-coated capsules targeted release to the distal small intestine and adhered to the intestinal mucosa, but the rat model presented limitations with respect to evaluating the overall performance. Based on the in vitro and in vivo results, further investigations in larger animals are a logical next step where fluid volumes, pH, and transit times are more favorable for the evaluated dosage forms.

Development of immunologic-based biopharmaceutical products have strikingly increased in recent years and have made evident contributions to human health. Antibodies are the leading entity in immunotherapy, while chimeric antigen receptor T cells therapies are the advent of a novel strategy in this area. In order to enable antibody candidates or cells available as products, formulation is critical in terms of stabilize molecules or cells to achieve practical shelf life, storage and handling conditions. Here we provide a concise and contemporary review of ongoing formulation strategies and excipients used in approved antibodies and cellular therapeutic products. Excipients are categorized, and their function in formulations are discussed.

The caveolin scaffolding domain peptide (CSP) is being developed for the therapeutic intervention of a lethal lung disease, idiopathic pulmonary fibrosis. While direct respiratory delivery of CSP7 (a 7-mer fragment of CSP) is considered an effective route, proper formulation and processing of the peptide are required. First, air-jet milling technology was performed in order to micronize the neat peptide powder. Next, the fine particles were subjected to a stability study with physical and chemical characterizations. In addition, the in vivo efficacy of processed CSP7 powder was evaluated in an animal model of lung fibrosis. The results revealed that, with jet milling, the particle size of CSP7 was reduced to a mass median aerodynamic diameter of 1.58 ± 0.1 μm and 93.3 ± 3.3% fine particle fraction, optimal for deep lung delivery. A statistically significant reduction of collagen was observed in diseased lung tissues of mice that received CSP7 powder for inhalation. The particles remained chemically and physically stable after micronization and during storage. This work demonstrated that jet milling is effective in the manufacturing of a stable, excipient-free CSP7 inhalation powder for the treatment of pulmonary fibrosis.

A transdermal drug delivery system (TDDS) is generally designed to deliver an active pharmaceutical ingredient (API) through the skin for systemic action. Permeation of an API through the skin is controlled by adjusting drug concentration, formulation composition, and patch design. A bilayer, drug-in-adhesive TDDS design may allow improved modulation of the drug release profile by facilitating varying layer thicknesses and drug spatial distribution across each layer. We hypothesized that the co-release of two fixed-dose APIs from a bilayer TDDS could be controlled by modifying spatial distribution and layer thickness while maintaining the same overall formulation composition. Franz cell diffusion studies demonstrated that three different bilayer patch designs, with different spatial distribution of drug and layer thicknesses, could modulate drug permeation and be compared with a reference single-layer monolith patch design. Compared with the monolith, decreased opioid antagonist permeation while maintaining fentanyl permeation could be achieved using a bilayer design. In addition, modulation of the drug spatial distribution and individual layer thicknesses, control of each drug's permeation could be independently achieved. Bilayer patch performance did not change over an 8-week period in accelerated stability storage conditions. In conclusion, modifying the patch design of a bilayer TDDS achieves an individualized permeation of each API while maintaining constant patch composition.

Tablet defects encountered during the manufacturing of oral formulations can result in quality concerns, timeline delays, and elevated financial costs. Internal tablet cracking is not typically measured in routine inspections but can lead to batch failures such as tablet fracturing. X-ray computed tomography (XRCT) has become well-established to analyze internal cracks of oral tablets. However, XRCT normally generates very large quantities of image data (thousands of 2D slices per data set) which require a trained professional to analyze. A user-guided manual analysis is laborious, time-consuming, and subjective, which may result in a poor statistical representation and inconsistent results. In this study, we have developed an analysis program that incorporates deep learning convolutional neural networks to fully automate the XRCT image analysis of oral tablets for internal crack detection. The computer program achieves robust quantification of internal tablet cracks with an average accuracy of 94%. In addition, the deep learning tool is fully automated and achieves a throughput capable of analyzing hundreds of tablets. We have also explored the adaptability of the deep learning analysis program toward different products (e.g., different types of bottles and tablets). Finally, the deep learning tool is effectively implemented into the industrial pharmaceutical workflow.

Idiopathic pulmonary fibrosis (IPF) is associated with progressive destruction of the lung parenchyma with a median survival after diagnosis of three years and a five-year survival of