Search

Dye-sensitized solar cells have better development prospects than silicon cells, and their main structural composition of nanoporous semiconductor films is particularly important. It is the tin dioxide film, and the effect of preparing tin oxide film on dye-sensitized solar cells under different conditions is studied. In this paper, the SnO2 powder was prepared by hydrothermal method, and the experiment was studied by controlled variable method. The properties of the obtained tin dioxide powder were characterized by SEM and three-dimensional ultra-depth microscope and XRD. The XRD diffraction peak is shown as tetragonal phase rutile type SnO2, With the increase of the concentration of tin tetrachloride solution, the coarser the particle size of the tin oxide crystal in the film, the more complicated the surface morphology, so that the specific surface area of the film is larger. At 0.1 mol/L, the surface of the film is a porous structure in the form of a loose sheet is presented. After analyzing the surface microstructure and flatness of the tin dioxide film, it can be concluded that the effect of salt concentration on the specific surface area of the film is extremely large. When the salt concentration is higher or lower, the obtained two the surface of the tin oxide film is relatively flat and has poor performance. When the salt concentration is 0.1mol/L, the surface of the obtained film has a large undulation and a large specific surface area, and the ability to adsorb the dye molecules can be predicted to be the greatest, and the photoelectric conversion efficiency is optimal in the photocatalytic process.

In this paper, the effect of sintering temperature on the interfacial structure of the composite was investigated and three different formulation groups were used to compare the respective properties. To obtain a composite material with excellent interface, the law between reference number and performance is obtained. Through mixing, molding, sintering, sample preparation, scanning electron microscopic observation, energy spectrometer observation and analysis, the following conclusions can be drawn: As the temperature increases, the density and hardness increase. The sample melts at 1500 °C, and there is no specific data. When the temperature reaches 1450 °C, the density and hardness reach the highest. When the formulation is Fe:Al2O3:SiO2=18:1:1 and the temperature reaches 1450 °C, the properties of the sample materials are optimized. The density is as high as 95% and the hardness reaches 42.9HBW.

In this paper, the effect of raw materaisl on the properties of coated Al2O3/Al cermet materials were investigated, the raw materials were prepared via different methods, which provide a reference for obtaining higher performance cermet materials. Through mixing, molding, sintering, sample preparation, scanning electron microscopic observation, energy spectrometer observation and analysis, the following conclusions can be drawn, the density of the cermet material prepared by the mechanical ball milling method (83.5%) is higher than that of the cermet material prepared by the chemical precipitation method (92.8%). It is nearly 10% lower. The alumina particles prepared by the ball milling method are agglomerated, and a large amount of agglomeration occurs in the aluminum, and the composition is very uneven. For materials prepared by the precipitation method, the aluminum oxide is uniformly distributed in the aluminum. The ball-milling powder is used to prepare materials, most of the alumina is in the form of particles, and in the precipitation method. In the powder preparation sample, the thin layer of alumina which forms the same eggshell envelops the aluminum, and the aluminum has a certain liquid phase change. the surface hardness (824HV) of the cermet material prepared by the mechanical ball milling method is lower than the surface hardness (1005HV) of the cermet material prepared by the chemical precipitation method.

Both alumina and boron carbide have good hardness and strength, and are widely used in production and life, industrial manufacturing, and military defense. However, due to the insufficiency of research at this stage and the lack of technical means, it is difficult to prepare alumina-boron carbide composite powder with good coating and ultra high strength through large-scale batch production. Therefore, this experiment wants to obtain a relatively good performance of coated Al2O3/B4C cermet by hydrothermal method through different experimental parameter ratios. Through the experimental results and analysis, the following conclusions are obtained. The most suitable concentration of aluminum nitrate is 0.1 mol/l. The low concentration affects the formation of alumina particles. The concentration is too high and prone to agglomeration. Through the optimization of hydrothermal synthesis concentration, a composite of Al2O3/B4C composite with good nanoencapsulated structure was obtained. The composite powder was pure in composition and high in specific surface area, which lays a foundation for solving the low-temperature preparation of high-density boron carbide ceramics.

In this paper, the effect of raw materaisl on the properties of coated Al2O3/Al cermet materials were investigated, the raw materials were prepared via different methods, which provide a reference for obtaining higher performance cermet materials. Through mixing, molding, sintering, sample preparation, scanning electron microscopic observation, energy spectrometer observation and analysis, the following conclusions can be drawn, the density of the composite material increases first and then decreases with the increase of the molding pressure. When the molding pressure is 30 MPa, the density of the composite material reaches the maximum value, that is 93.5%. The greater the applied pressure, the more compact the aluminum powder and alumina powder, and the longer the tissue composition, the more uniform. there is no crack in the c-picture, and there are cracks in the a and b pictures. The microstructure of metal matrix composites prepared at different molding pressures is also different. Sintering of the green body formed at 30 MPa resulted in relatively few cracks and voids in the material. The surface hardness of the composite material increases first and then decreases with the increase of the molding pressure, and the surface hardness of the composite material reaches a maximum value (875 HV) at a molding pressure of 30 MPa.

Ultrafine SnO2 is a new type of material, in the field of solar cells and semiconductors have a lot of use. To get different morphology and different properties of tin oxide powder material, making more applications in the field, the effect of the adjuvants on the properties of superfine SnO2 powders were distigated. Through the analysis of experimental results, the conclusions are shown the stronger the alkalinity of the auxiliary agent, the larger the grain size of the obtained particles and the more uniform the particles. When the molar ratio of salt to alkali is more than 1: 4, the amount of alkali is gradually reduced, the particle size is small, the morphology is not uniform and easy to agglomerate. When the molar ratio of salt to alkali is 1: 4, the smaller particle size is shown, the appearance morphology is uneven. The longer the reaction time, the more complete the grain, the more uniform the morphology. Under the condition of SnCl4 concentration of 0.05 mol/L, reaction time is 4 days, salt and alkali molar ratio is 1: 4, holding temperature is 200 °C, the auxiliary agent is NaOH, the size, shape and properties of synthesized SnO2 are the better.

The Al2O3/Al cermet composite powders were prepared via the ball milling method,which provide raw materials for preparing high performance cermet materials. The results show that the number of Al2O3 particles on the surface of Al particles increases first and then decreases with increasing the ball milling time and milling rotating speed. The number of Al2O3 particles on the surface of Al particles increases with increasing ball to powder mass ratio. The analysis of the ratio of performance to price shows that the better parameters for preparing the pinned Al2O3/Al cermet composite powders are as follows, the ball milling time 24h,the ball milling rotating speed 100 r/min and the ratio of ball to powder 1:2.

Cermet while maintaining the excellent properties of ceramic materials, but also have the advantages of a metal material, is an important new engineering materials. In this paper, Al-Al2O3 cermet is prepared using different molding process via the powder metallurgy method to study the properties of Al-Al2O3 cermet. The conclusions are shown the density of the initial and late increase is not obvious with the cermet body forming pressure increases, but the increase in density of 20-30MPa is more obvious. The density of the cermet material increases with prolonging holding pressure time is shown, the initial increase speed is faster, and the later growth rate becomes weaker. In the different molding pressure, the pressure is 40MPa and 15min, sintering temperature is 700°C and 1h, the sample density is 2.084g/cm3, the highest density, the best performance, aluminum and alumina distribution is the most uniform.

To provide reference for optimizing the photoelectric conversion efficiency, we studied the effects of salt–alkali molar ratio on the properties of tin oxide nanofilms. We found that when the hydrothermal temperature was increased to 80 °C, the film growth was not complete. With a hydrothermal temperature of 120 °C, the film became more complete and structured. However, at 160 °C, thick and very irregular tin dioxide (SnO2) crystal particles were deposited on the FTO conductive glass surface. With the increase in heat treatment temperature, crystallization became more and more dense and complete. At 80 °C hydrothermal temperature, the simulated peak of the surface and number of peaks became smaller. However, they significantly increased with a hydrothermal temperature of 120 °C. When the hydrothermal temperature was at 160 °C, the surface simulated peak increased, but the number of peaks decreased. Moreover, the diameter of each peak was greatly increased. The film obtained via the hydrothermal method was relatively pure, and Sn(OH)3 was not completely converted into SnO2.

The YAM coatings on the ZrB2 composites surface were prepared by co-precipitation technique and with Al (NO3)3 and Y(NO3)3 solutions acting as precursor. The effect of matrix surface treating conditions, dipping times and calcination temperature was investigated. Phase compostion, coating morphology and interface between matrix and coating were analyzed by XRD and SEM. The results indicated that the YAM coating was formed after calcined at 1250°C in vaccum. The thickness of coating was increased with the dipping times, the smoothest coating was obtained by two dipping times, and matrix surface coarsing was beneficial for improving the adhension between matrix and coating. The ablative teste was evaluated at 2000°C by oxy-acetylene flame, the ablative properties was obviously improved by coating compared with uncoated composites.

Cermet while maintaining the excellent properties of ceramic materials, but also have the advantages of a metal material, is an important new engineering materials. In this paper, Al-Al2O3 cermet is prepared adding different sintering aids via the powder metallurgy method to study the properties of Al-Al2O3 cermet. The conclusions are shown the adding sintering aids can significantly improve the sintered density of Al-Al2O3 cermet. The sintering aiding effect of adding MgO is better than that of SiO2 and Y2O3, and the hardness and the strength of the sample are higher than those of samples with SiO2 and Y2O3, and the densification degree of Al-Al2O3 metal ceramic material is the best, the relative density is 94.8%, the surface hardness is 824HV. The flatness of the surface of the sample adding MgO shows that the bonding strength between aluminum powder and alumina powder is high. The prepared Al-Al2O3 cermet adding different sintering aids have higher density and fewer pores in the microstructure the prepared Al-Al2O3 cermet adding sintering aids has a package structure.

In atmospheric environments, Al2O3 ceramics have good oxidation resistance in water, acid, and other solutions and suitable corrosion medium resistance. Al2O3 ceramics is one of the most widely used engineering ceramics. In this paper, Al2O3/Al cermet matrix composites were prepared by mixing a series of powders with aluminum and alumina powders as raw materials. The interface of Al2O3/Al cermet was observed by scanning electron microscopy. The densification process of Al2O3/Al cermet was then explored from the aspects of formulation, molding pressure, holding time, and sintering process. After mixing and dry pressing, 50 wt% Al and 50 wt% Al2O3 were appropriate for sintering. Following sintering and measuring density, density was improved under 20 MPa with a 20-minute holding time. Through a comparison of the sintering process, the interface structure was observed via scanning electron microscopy, which found that secondary sintering is conducive to improving the density of Al2O3/Al cermet.

Dense 3Y-ZrO2 composite ceramics were prepared by using 3Y-ZrO2 nanopowders as the raw materials, via the process of ball milling, granulating, molding and calcination.We investigated the microstructure, surface morphologies, the mechanical property, the density and linear shrinkage rate of the sintered ceramics and the effect of the ball milling technics and the sintering technics on the above properties of the3Y-ZrO2 composite ceramics via SEM and testing. The results show that the most excellent technics in all was explored as follows: the ultrafine ball milling by adding zirconium balls of 2 mm at the speed of 35 r/min for 10 h, with the mass ratio of zirconium ball, water and mixed powders of 6:1:1, the granulaing with 1.5% PVA, the CIP, the pre-sintering to remove the organic substrate to 500°C and the microwave sintering from 20°C to 1450 °Cin 80 min in which the duration at 1450°C was 20 min and the natural cooling time of the samples was 90 min. And the 3Y-ZrO2 composite ceramics obtained by this process have a relative density of 99.2%, bending strength of 1098 MPa, and a fracture toughness of 7.8 MPa·m1/2.

Ultrafine Co2O3 powder was prepared via hydrothermal synthesis. The effect of technology on the performance of the superfine Co2O3 powders was investigated, and the hydrothermal parameters in preparing Co2O3 were gradually improved. In addition, the morphology and grain size of the Co2O3 powder were analyzed by FESEM. Results show that reducing the salt–alkali molar ratio resulted in more uniform Co2O3 powder and smaller particles, with average particle size of approximately 40 nm. Reaction time displayed little effect on the Co2O3 powder, but the particle size decreased with the reaction time. The concentration of salt solution remarkably affected the morphology of the Co2O3 powder. Lower concentration resulted in smaller particle aggregation and particle size.

Cermet includes the excellent properties of ceramic materials and the advantages of metal materials, so it is an important new engineering material. In this paper, Al2O3-Al cermet is prepared using different molding process via the powder metallurgy method to study the properties of Al2O3-Al cermet. The conclusion are shown the increasing density of Al2O3-Al cermet is not obvious with increasing the forming pressure of cermet body during the initial and late processing, but the increasing density is more obvious under the forming pressure for 20-30MPa. The density of cermet materials are increased with prolonging holding pressure time, the initial increase speed is faster, and the later growth rate becomes weaker. When the molding pressure is 30MPa, the holding time is 10min, the sintering temperature is 900°C, the holding time is 1h, the prepared Al2O3-Al cermet adding sintering aids has a coated microstructure, which indicates that the large number of particles is migrated on the grain boundary. The sample density is 2.26g/cm3, the density is highest, the distribution of Al2O3 and Al phase is the most uniform. The buried sintering method is more suitable for the preparation of Al2O3-Al cermet composites than the nudity sintering method.

This work investigated the effects of molar ratio of salt to alkali on the properties of tin oxide nanofilms to provide reference for optimizing its photoelectric conversion efficiency. The tin oxide film grown by hydrothermal method exhibited poor film-forming property. The macroscopic analysis revealed the formation of a thick film. The bonding force to the FTO substrate was poor, its brittle, and easy to fall off. When the molar ratio of salt to alkali was 1:8, the tin oxide film exhibited improved microstructure and large specific surface area, which could benefit electron transport. Moreover, the film showed excellent photoelectric conversion performance. However, mechanical properties, such as adhesion between the tin oxide film and the conductive glass FTO, remain to be improved.

Alumina ceramics with good mechanical and corrosion resistance are the ones of the most widely used engineering ceramics. The aluminum has high strength, high conductivity and high plasticity etc. so that aluminum ceramics are used in more and more industries. In this paper, the mass fraction of 25% Al2O3 powder and the mass fraction of 75% Al powder were mixed in the blender. Mixer speed is100r/min with mixing time of 3.5 h. Forming, sintering and a series of processes for preparing the alumina/aluminum metallic ceramic materials, through performance testing and analysis, found that the density of the sample firstly increased and then decreased with the increase of sintering temperature. A melting point is close to the sintering temperature and the density of the cermet can be made relatively high. When the sintering temperature is about 600°C and 700°C, the macro performance of sample is better. The cermet is sintered at 700°C and its microstructure is relatively better.