Search

Phenol-formaldehyde (PF) resole and polymeric diphenylmethane diisocyanate (PMDI) are two commonly used exterior thermosetting adhesives in the wood-based composites industry. There is an interest in combining these two adhesives in order to benefit from their positive attributes while also neutralizing some of the negative ones. Although this novel adhesive system has been reportedly utilized in some limited cases, a fundamental understanding is lacking. This research serves this purpose by investigating some of the important aspects of this novel adhesive system. The adhesive rheological and viscometric properties were investigated with an advanced rheometer. The resole/PMDI blends exhibited non-Newtonian flow behavior. The blend viscosity and stability were dependent on the blend ratio, mixing rate and time. The adhesive penetration into wood was found to be dependent on the blend ratio and correlated with the blend viscosity. By using dynamic mechanical analysis, the blend cure speed was found to increase with the PMDI content. Mode I fracture testing of resole/PMDI hybrid adhesive bonded wood specimens indicated the dependence of bondline fracture energy on the blend ratio. The 75/25 PF/PMDI blend exhibited a high fracture energy with a fast cure speed and processable viscosity. Exposure to water-boil weathering severely deteriorated the fracture energies of the hybrid adhesive bondlines. More detailed chemistry and morphological studies were performed with cross-polarization nuclear magnetic resonance and 13C, 15N-doubly labeled PMDI. A spectral decomposition method was used to obtain information regarding chemical species concentration and relaxation behavior of the contributing components within the major nitrogen resonance. Different urethane concentrations were present in the cured blend bondlines. Water-boil weathering and thermal treatment at elevated temperatures (e.g. > 200°C) caused reduced urethane concentrations in the bondline. Solid-state relaxation parameters revealed a heterogeneous structure in the non-weathered blends. Water boil weathering caused a more uniform relaxation behavior in the blend bondline. By conducting this research, more fundamental information regarding the PF/PMDI hybrid adhesives will become available. This information will aid in the evaluation of, and improve the potential use of PF/PMDI hybrid adhesives for wood-based composites. Ph. D.

This thesis describes a computing environment WBCSim and its experiment management component. WBCSim is a web-based simulation system used to increase the productivity of wood scientists conducting research on wood-based composite and material manufacturing processes. This experiment management component integrates a web-based graphical front end, server scripts, and a database management system to allow scientists to easily save, retrieve, and perform customized operations on experimental data. A detailed description of the system architecture and the experiment management component is presented, along with a typical scenario of usage. Master of Science

This work addresses the morphology of the wood/ Phenol-Formaldehyde (PF) adhesive interphase using yellow-poplar. In this case, morphology refers to the scale or dimension of adhesive penetration into wood. The objective is to develop methods for revealing ever smaller levels of wood/resin morphology. Dynamic techniques that are commonly utilized in polymer blend studies are investigated as potential methods for probing the wood/ adhesive interphase morphology. These are Dynamic Mechanical Analysis (DMA) and solid state NMR using CP/MAS. PF resin molecular weight is manipulated to promote or inhibit resin penetration in wood, using a very low or a very high molecular weight PF resin. With DMA, the influence of PF resin on wood softening is investigated. It is first demonstrated that the cooperativity analysis according to the Ngai coupling model of relaxation successfully applies to the in-situ lignin glass transition of yellow-poplar and spruce woods. No significant difference in intermolecular coupling is detected between the two woods. It is then demonstrated that combining simple DMA measurements with the cooperativity analysis yields ample sensitivity to the interphase morphology. From simple DMA temperature scans, a low molecular weight PF (PF-Low) does not influence lignin glass transition temperature. However, the Ngai coupling model of relaxation indicates that intermolecular coupling is enhanced with the low molecular weight PF. This behavior is ascribed to the low molecular weight PF penetrating lignin on a nanometer scale and polymerizing in-situ. On the other hand, a high molecular weight resin with a broad distribution of olecular weights (PF-High) lowers lignin glass transition temperature dramatically. This plasticizing effect is ascribed to a small fraction of the PF resin being low enough in molecular weight to penetrate lignin on a nanoscale, but being too dispersed for forming a crosslinked network. With CP/MAS NMR, intermolecular cross-polarization experiments are found unsuitable to probe the angstrom scale morphology of the wood adhesive interphase. However, observing the influence of the PF resins on the spin lattice relaxation time in the rotating frame, HT1r, and the cross-polarization time (TCH) is useful for probing the interphase morphology. None of the resins significantly affects the cross-polarization time, suggesting that angstrom scale penetration does not occur with a low nor a high molecular weight PF resin. However, the low molecular weight PF substantially modifies wood polymer HT1r, indicating that the nanometer scale environment of wood polymers is altered. On the other hand, the high molecular weight PF resin has no effect on wood HT1r. On average, the high molecular weight PF does not penetrate wood on a nanometer scale. Interestingly, the low molecular weight PF resin disrupts the spin coupling that is typical among wood components. Spin coupling between wood components is insensitive to the high molecular weight PF. Finally, it is noteworthy that the two PF resins have significantly different T1r 's in-situ. The low molecular weight resin T1r lies within the range of wood relaxations, suggesting some degree of spin coupling. On the other hand, the T1r of the high molecular weight PF appears outside the range of wood relaxations. Spin coupling between the high molecular weight resin and wood components is therefore inefficient. The CP/MAS NMR and DMA studies converge to identify nanometer scale penetration of the low molecular weight PF in wood. On the other hand, the high molecular weight PF resin forms separate domains from wood, although a very small fraction of the PF-High is able to penetrate wood polymers on a nanoscale. Ph. D.

The importance of precise values for the parameters used in heat and mass transfer models has been demonstrated by many research studies. Thermal conductivity values used in previous models are usually empirical and fluctuate. Theoretical analysis and estimations of wood thermal conductivities in the radial and tangential directions were conducted with the geometric models built up from the macro- and micro-structure observations. Theoretically, thermal conductivity in the radial direction is about 1.5 to 2.5 times of the tangential direction for softwood species with moisture content (MC) below Fiber Saturation Point (FSP). When MC is over the FSP, tangential radial thermal conductivity both increase dramatically and are linear function of MC. The two thermal conductivity values are close with a ratio of near one estimated by the model for MC above the FPS. In hardwood species, radial thermal conductivity estimated by the model is 1.5 times of the tangential thermal conductivity. Validation tests for model estimations of thermal conductivities in the radial and tangential directions for three wood species showed the reliability of the geometric models developed in this project. Correlations between the wood thermal conductivity and structure parameters, such as latewood percentage and cell wall percentage, were examined. Linear relationships for the thermal conductivity and average temperature in wood were established in both radial and tangential directions of three wood species. A two-dimensional transient heat conduction model was developed utilizing thermal conductivity values derived from geometric models. The anisotropic material property affect on heat transport in radial and tangential directions was discussed using an assumed situation. The simulation run showed slightly faster heat flow in the radial direction than in the tangential direction due to higher thermal conductivity in the radial direction. Validation tests on practical wood blocks showed the 2D model with the use of theoretical thermal conductivity values can predict good temperature distribution in wood during the heating process. However, in the practical wood samples with curved rings on the cross section, no significant difference was found in the two transverse directions. Mathematica software was introduced in this study for the intense and complicated math calculations and model programming. Mathematica was found to be a powerful technique for solving sophisticated math problems. It had abundant and flexible plotting options for providing optimized presentations for the results. These advantages make Mathematica popular for engineering modeling research. Ph. D.

This research focuses on experimental investigations of the drying and bending properties of wood flakes. Three species (southern yellow pine, sweetgum, and yellow-poplar) were tested. Experiments on flake drying and effect of flake properties (cutting direction and dimension) and an external factor (temperature) were used to evaluate the flake drying process. Drying experiments were conducted using a convection oven. Bending properties of dried flakes were also measured. Modulus of elasticity (MOE), modulus of rupture (MOR), and strength at proportional limit (SPL) of flakes were measured based on Methods of Testing Small Clear Specimens of Timber (ASTM D143-94) using a miniature material tester. The drying curve was characterized by a second-order/quadratic equation. This equation was then differentiated to get the drying rate curve. Observation on drying and drying rate curves revealed that the rate of moisture loss consists of two falling rate periods; no constant rate drying period was observed. First falling rate drying period is controlled by convective heat transfer. Bound water diffusion controls the second falling rate drying period. Species, cutting direction, dimension, and temperature were found to have significant effect on drying rate of wood flakes. Southern yellow pine has the fastest drying rate followed by sweetgum then yellow-poplar. Differences in drying rate between species were attributed to differences in specific gravity and other factors. Radially-cut specimens have a slower drying rate than tangentially-cut specimens. There were also significant differences in drying rate between the four different flake dimensions. Thickness was found to be the more sensitive parameter in terms of dimensions. As expected, drying temperature also had highly significant effect on drying rate. An increasing trend in drying rate was observed as drying temperature increased. Simulation of flake drying using a numerical model yielded a different result. Simulated flake drying has two drying periods: a constant rate and falling rate. Moisture of the flake decreases constantly and surface temperature increases rapidly to boiling point and remains there in the constant rate drying period. During the falling rate period, rate of moisture transport is limited by the ability of water to diffuse through wood and flake temperature starts to rise. Bending properties were found to vary between and within the three species. Southern yellow pine had the lowest bending stiffness and strength followed by sweetgum while yellow-poplar had the highest bending properties. Radially-cut specimens were found to have lower MOE, MOR, and SPL than tangentially-cut specimens. Drying temperature was also found to have a significant effect on bending stiffness and strength. A decreasing trend in bending properties was observed when drying temperature was increased. Ph. D.

The increased use of wood composites in building materials results in a need for a better understanding of wood adhesion. The effects of water and temperature exposure on the durability of wood products were assessed using the double-cantilever beam (DCB) method of fracture testing. The relative durability of phenol-formaldehyde (PF) and isocyanate (pMDI) adhesives was compared using a 2-hour boil test and an environmental test. The feasibility of using oriented strandboard (OSB), oriented strand lumber (OSL) and parallel strand lumber (PSL) for the DCB fracture method was assessed. The fracture resistance of PF was reduced significantly by the aging exposures. The fracture resistance of pMDI did not decrease after the 2-hour boil test. The DCB fracture method was shown to be useful with a square-grooved machined specimen using OSB and OSL. Master of Science

A numerical model based on fundamental engineering principles was developed and validated to establish a relationship between process parameters and the final properties of woodbased composite boards. The model simulates the mat formation, then compresses the reconstituted mat to its final thickness in a virtual press. The number of interacting variables during the hot-compression process is prohibitively large to assess a wide variety of data by experimental means. Therefore, the main advantage of the model based approach that the effect of the hot-compression parameters on the final properties of wood-based composite boards can be monitored without extensive experimentation. The mat formation part of the model is based on the Monte Carlo simulation technique to reproduce the spatial structure of the mat. The dimensions and the density of each flake are considered as random variables in the model, which follow certain probability density distributions. The parameters of these distributions are derived from data collected on industrial flakes by using an image analysis technique. The model can simulate the structure of a threelayer oriented strandboard (OSB) mat as well as the structure of random fiber networks. A grid is superimposed on the simulated mat and the number of flakes, the thickness, and the density of the mat at each grid point are computed. Additionally, the model predicts the change in several void volume fractions within the mat and the contact area between the flakes during consolidation. The void volume fractions are directly related to the physical properties of the mat, such as thermal conductivity, diffusivity, and permeability, and the contact area is an indicator of the effectively bonded area within the mat. The heat and mass transfer part of the model predicts the change of air content, moisture content, and temperature at designated mesh points in the cross section of the mat during the hotcompression. The water content is subdivided into vapor and bound water components. The free water component is not considered in the model due to the low (typically 6-7 %) initial moisture content of the flakes. The gas phase (air and vapor) moves by bulk flow and diffusion, while the bound water only moves by diffusion across the mat. The heat flow occurs by conduction and convection. The spatial derivatives of the resulting coupled partial differential equations are discretized by finite differences. The resulting ordinary differential equation in time is solved by a differential-algebraic system solver (DDASSL). The internal environment within the mat can be predicted among different initial and boundary conditions by this part of the hot-compression model. In the next phase of the research, the viscoelastic (time, temperature, and moisture dependent) response of the flakes was modeled using the time-temperature-moisture superposition principle of polymers. A master curve was created from data available in the literature, which describes the changing relaxation modulus of the flakes as a function of moisture and temperature at different locations in the mat. Then the flake mat was compressed in a virtual press. The stress-strain response is highly nonlinear due to the cellular structure of the mat. Hooke's Law was modified with a nonlinear strain function to account for the behavior of the flake mat in transverse compression. This part of the model gives insight into the vertical density profile formation through the thickness of the mat. Laboratory boards were produced to validate the model. A split-plot experimental design, with three different initial mat moisture contents (5, 8.5, 12 %), three final densities (609, 641, 673 kg êm3 or 38, 40, 42 lb ê ft3), two press platen temperatures (150, 200 °C), and three different press closing times (40, 60, 80 s) was applied to investigate the effect of production parameters on the internal mat conditions and the formation of the vertical density profile. The temperature and gas pressure at six locations in the mat, and the resultant density profiles of the laboratory boards, were measured. Adequate agreement was found between the model predicted and the experimentally measured temperature, pressure, and vertical density profiles. The complete model uses pressing parameters (press platen temperature, press schedule) and mat properties (flake dimensions and orientation, density distribution, initial moisture content and temperature) to predict the resulting internal conditions and vertical density profile formation within the compressed board. The density profile is related to all the relevant mechanical properties (bending strength, modulus of elasticity, internal bond strength) of the final board. The model can assist in the optimization of the parameters for hot-pressing woodbased composites and improve the performance of the final panel. Ph. D.

There have been successful techniques developed to measure resin distribution of phenol-formaldehyde adhesive on several types of wood surfaces. However, a technique that quantitatively measures UF resin on wood surfaces has been a problem because UF resin is colorless on wood fiber. The first objective of this study was to develop a technique to quantitatively measure surface area coverage and statistical distribution of urea-formaldehyde (UF) resin on medium density fiberboard (MDF) fiber. Two techniques were evaluated to quantitatively measure UF resin. One technique treated the resinated fiber with a reactive stain, such that the resin and wood could be distinguished and separated using digital image analysis. An epi-fluorescence microscope, color video camera, A/D image capture board, and image analysis software were used to measure the percent of resin coverage on the wood surface. The measured resin coverage of the treated fibers did not correlate with the target resin loading level. The other technique added ultraviolet dye to the resin and measured the distribution of resin with an image analysis system. The results of a mill trial confirmed the accuracy of the technique. This system has potential to be incorporated into a mill setting, which will provide MDF mills with a method of determining how resin is being distributed on their fiber. The second objective of this study was to identify factors that would influence the technique's acceptance among MDF mills. A questionnaire was developed, pretested, and sent to every MDF mill in the United States. The method of adding UV dye into the resin was favorable to most mills and could be tested either on-site or by a third-party company. This allows MDF mills to determine potential problems with their blending process. This method saves time and money since it is a proactive measure rather than a reactive measure. It should also lead to a more uniform and consistent product, which is the goal of every MDF mill. Master of Science

Land use issues have dramatically changed the timber supply outlook for our nation's forest products industry. Since demand for wood products shows no sign of abating, alternative products must be developed. Bamboo is a very promising alternative raw material for the manufacture of structural composite products. It is fast growing, economical, renewable and abundant throughout the world. Bamboo has physical and mechanical properties that are comparable to many commercial timber species, and thus, may easily be processed using existing technology from the wood-based composites industry. Bamboo can be cultivated in the U.S., and thus has the potential to relieve some of the harvesting pressure from our nation's forestlands. However, the use of specific bamboo species for structural composite products will require a thorough investigation of the material as well as its interaction with other components. Thus, the primary objective of this dissertation is to determine the properties of Calcutta bamboo and its interaction with adhesives. The properties investigated were relative density, dimensional stability, equilibrium moisture content, bending strength and stiffness, tensile strength, pH, buffer capacity, wettability and the adhesive penetration. In addition to this, a prototype bamboo parallel strip lumber (BPSL) was manufactured and tested for its physical and mechanical properties. The relationships among the properties of Calcutta bamboo and the prototype bamboo composite were also investigated. As the result of these investigations, it is concluded that Calcutta bamboo is technically a suitable raw material for structural composite products. This result may also be applicable for the utilization of other bamboo species, thus aiding companies in decisions regarding investment in bamboo plantations and manufacturing facilities in the U.S, Malaysia and other parts of the world. The primary benefits from this research may be the development of new products to serve growing markets, and thereby relieving some of the pressure to harvest forestlands. Ph. D.

The objective of this thesis was to further develop the polymer composite system consisting of cellulose acetate butyrate (CAB) and high modulus, continuous, regenerated cellulose fiber (lyocell). Of particular concern were both the interfacial adhesion between the fiber and matrix and the consolidation process in the manufacture of these composite materials. Interfacial adhesion was found to be substantial due to the relative lack of the fiber pull-out phenomenon observed after tensile failure in the unmodified fiber composites. This result was then supported in the second study in which similar unmodified fiber composites experienced very little fiber pull out with evidence of a large amount of cohesive failure of the matrix accompanied by matrix particles adhering to the fiber surfaces. Void volume formation was mitigated to a small extent by the use of optimal consolidation conditions. Composites formed at moderate temperature (200 °C), low consolidation pressure (11.8 p.s.i.) and high consolidation time (13 min.) were found to have the lowest void volume formation of ca. 2.8 %. These composites were generally found to have the highest interfacial shear strength, ca. 16 MPa. A tensile modulus of 22 GPa and an ultimate strength of 246 MPa was obtained for this composite having a fiber volume content of ca. 62 %. Master of Science

An improved knowledge of wood material behavior in hot-pressing environments can provide the benefit of an increased understanding of material properties during the manufacture of wood-based composites as well as insight into the development of new processes and products which manipulate the viscoelastic nature of wood. Two specific areas where additional knowledge is needed are: the high temperature equilibrium moisture content (EMC) behavior and the moisture dependent softening behavior. EMC data was collected and desorption isotherms were generated for mature and juvenile wood of aspen, loblolly pine and yellow-poplar at 50 and 160°C. High temperature EMC behavior was found to be distinct from that at lower temperatures, and considerable differences between the isotherms for juvenile and mature wood were detected. Substantial thermal degradation was observed during desorption at 160 °C and found to be strongly influenced by relative humidity. The thermal softening behavior of wood was evaluated using dielectric thermal analysis (DETA) at moisture levels from 0 to 20 percent. Coincident in situ relaxations of hemicellulose and amorphous cellulose in the range of 20 to 200 °C were observed and found to exhibit the characteristics of a secondary (glass) transition. The moisture dependence of this transition was characterized, and differences in the observed Tg were detected between juvenile and mature wood. Time-temperature superposition was also shown to be applicable to the wood-water system. Ph. D.

Phenol Formaldehyde (PF) and polymeric isocyanate (pMDI) are the two main types of adhesives used in the production of structural wood-based composites. Much is unknown about various aspects of adhesion between these two types of resins and wood. The present research describes the development of techniques which will permit an enhanced understanding of 1.) the extent of cure of PF within a wood based composite, 2.) the scale of molecular level interactions between PF and pMDI and wood, 3.) mechanical performance and durability of wood-adhesive bonds. Correlations were established between conventional methods of characterization of neat PF (thermomechanical analysis, swelling studies) and measurements made using 13C CP/MAS NMR. These correlations were then utilized to characterize PF cured in the presence of wood. The use of 13C labeled PF allowed estimates of relative degrees of resin conversion to be made. The use of 13C and deuterium labeled PF allowed qualitative estimates of resin molecular rigidity to be made. The scale of molecular level interactions between PF and pMDI and wood was probed using NMR relaxation experiments. Evidence was shown to suggest the formation of an interpenetrating polymer network (IPN) morphology existing at both types of wood-resin interphases. The formation of the IPN morphology was strongly influenced by resin molecular weight, cure temperature and the presence of solvent. A new test geometry for the evaluation of the fracture toughness of wood-adhesive bonds was developed. Consistent and reliable results were obtained. It was found that low molecular weight PF possessed enhanced durability over high molecular weight. Ph. D.

The objective of this research based on both the theory and experimentation was to prove that the total pressure difference is the primary driving force during the vacuum drying. The theoretical drying rates of diffusion, free water bulk flow and water vapor bulk flow were calculated and compared. The concept of equilibrium moisture content under the vacuum was developed. The theoretical maximum moisture content drop in one cycle was calculated using energy balance. The model was developed for the vacuum drying to understand the mechanism of the vacuum drying including the boiling front and its movement. To evaluate the effect of the sample size on the drying rate, four different thicknesses (1, 1.5, 2, 2.5 inches) and three different lengths (5, 10, 15 inches) were used. In the cyclic drying, the specimens were heated to the 60 C. The vacuum was pulled to about 18 mm Hg. The vacuum pump was kept running for 140 minutes. It was found that in cyclic vacuum drying, drying rate was not affected by the thickness. However, it was affected by the length. The cyclic drying curve consisted of two distinct parts. The fast drying period lasted about 10 to 20 minutes. The slow drying period occurred next when the pressure inside wood got close to the ambient pressure. In end grain vacuum drying, the specimens were coated with wax, wrapped in the plastic film and inserted into a rubber tube to prevent the moisture loss from the side surfaces during drying. The specimen size was 1×1×10 inches. Red oak and white oak were sealed and dried in both cyclic and continuous vacuum drying. The results showed that sealed specimens dried almost as fast as unsealed specimen. There was little moisture loss from the side surfaces. There was a moisture gradient along the length in both cyclic drying and continuous vacuum drying. Red oak specimens of 2.5×1.5×10 inches were used to study the boiling front in the vacuum drying. In order to detect the boiling phenomenon, the saturation pressures were calculated and were compared with the pressures at the same time and the same location. Boiling occurred during drying and the boiling front retreated to the center of wood as drying proceeded. The retreating speed depended on the heat supply and the permeability. Vacuum drying at room temperature was investigated. The specimens were dried at 20 C and pressure near 18 mm Hg. The results showed that wood can be vacuum dried at room temperature with little or no degrade at a reasonable drying rate. All experimental results support the objective of this study that the primary driving force is the total pressure difference. Ph. D.

The bond performance and surface energy of hygro-thermal compression densified wood were studied using comparisons to hygro-thermally treated and control yellow-poplar (Liriodendron tulipifera). Bond performance was studied using opening mode double cantilever beam fracture testing and cyclic boiling of one half of all fracture samples. Phenol formaldehyde film (PF-film) and polymeric diphenylmethane diisocyanate (pMDI) were the two different adhesives used to bond fracture samples. Hygro-thermal samples bonded with PF-film had significantly higher fracture toughness than control samples, while no difference was found for densified samples. Densified samples bonded with pMDI had significantly higher fracture toughness than control samples while no change was seen for hygro-thermal samples. Boil cycling reduced fracture toughness of hygro-thermal fracture samples only, irrespective of adhesive type. Surface energy was studied using sessile drop contact angle measurement and the Chang model of acid-base, surface energy component calculation. Water, glycerol, formamide, ethylene glycol, and -Bromonapthalene were used as probe liquids. Densified and hygro-thermally treated yellow-poplar had significantly higher contact angles than control samples. The contact angle trends for densified and hygro-thermally treated wood were found to be the same. Total surface energy as well as the polar and acid components of surface energy decreased with hygro-thermal treatment. The dispersive and base components of surface energy increased with hygro-thermal treatment. Master of Science

The intent of this research was to enhance our knowledge of aqueous phenolformaldehyde resin cure as it is affected by the elevated water vapor pressures that occur during hot-pressing of a wood-based composite. Microdielectric spectroscopy (DEA) was used to monitor the cure reaction, and thermomechanical analysis (TMA), swelling tests and scanning electron microscopy (SEM) techniques were used to characterize the final resin-network. Microdielectric results showed that as the water vapor pressure of the sy stem increases the time to gelation increases. It was also found that the injection of saturated water vapor sharply decreased the gelation time when compared to the other water vapor environmental conditions. In addition, it was found that the higher the water vapor pressure the lower the residual ion viscosity. Thermomechanical analysis and swelling test experiments showed that as the water vapor pressure increases the glass transition temperature and the cross-link density of the cured resin-network decreases. Considerable differences in the morphology of the network were found using SEM. Thus, it can be established that during the curing process under elevated water vapor pressures of a liquid phenol-formaldehyde adhesive some water is trapped into the resin network and it is acting as a plasticizer. A theoretical approach to model the cure kinetics of phenol-formaldehyde has been developed. The model is based on the occurrence of two simultaneous processes (condensation polymerization and evaporation of water) and on the concentration dependency of the activation energy of polymerization. Ph. D.

The Pallet Design System (PDS) is a widely accepted engineering procedure for comparing the performance of competing pallet designs. As part of a new version of the PDS, the objective of this study was to develop a durability model for pallets with structural panel decking. An accelerated rough material handling test system, "the VPI unit-load material handling FasTrack" , was developed to simulate pallets used in the unit-load material handling environments. 100 pallets representing 14 different designs were tested in the "FasTrack." Damages to these pallets were recorded after each test cycle. A procedure relating damage to repair cost was developed. The effect of panel-deck pallet design on the resistance to damage was evaluated in terms of the total number of damaged parts and average damage cost or repair cost. Test results indicate that panel grade and type, species of related wood parts, size of stringer and deckboards, joints, and pallet configurations affect the resistance of panel deck pallet to damage. The plots of average total damage cost, Cu adjusted for repair as a function of test cycle, U, fit the equation: Ct = aU - 1. The equation provided good fits to all the pallet designs tested. Using the initial purchase prices, the average cost and the economic life were calculated for all the pallet designs. The VPI "FasTrack" was calibrated based on the number of physical handlings and the amortized life. Three typical in-field handling environments were compared with the VPI "FasTrack". It concluded that the 30-cycle test period in the VPI "FasTrack" simulates between 2 to 5 years of field uses depending on the field handling system being simulated. Thirty Canadian Pallet Council (CPC) pallets with known 7 years of amortized life in the field were tested in the VPI "FasTrack". The 30-cycle test in the VPI system simulated 6 years of use in the similar handling environment of the CPC pallet used by the grocery industry in Canada. The average total damage costs for different pallet designs were related to pallet structural characteristics using multivariate regression analysis. The shear resistance through the thickness of the top panel deck, bottom deck flexural strength, pallet flexural strength, fastener withdrawal resistance, and pallet configuration were used to predict the total damage cost. A multiple regression model was developed. The model was verified by comparing the predicted values with the tested values of 12 panel deck pallets representing 2 designs. The results indicated that the model is reliable for the future predictions. Master of Science

A detailed design was developed of an apparatus to measure moisture transfer in porous materials. The apparatus is to be used to collect data to aid in the development of mathematical models which accurately describe this phenomena. The apparatus consists of dual environmental chambers between which a specimen material is sealed. The temperature of each chamber is controlled separately allowing nonisothermal test conditions. The relative humidity is maintained without the use of saturated salt solutions. The moisture transfer rate is measured by periodically weighing a desiccant column used to absorb moisture as result of diffusion across the specimen. The apparatus was built and used to verify a heat transfer model written to predict its thermal characteristics. The chamber temperature capabilities are 5°C to 60°C with up to a 20°C temperature difference across the specimen. The relative humidity limits are based on the heat transfer into or out of the system. High relative humidities (75 to 85 percent) are possible at chamber temperatures close to ambient, but decrease sharply at the extremely high or low temperatures and during nonisothermal operation. The apparatus maintains a constant temperature within ±0.4°C of the setpoint when subjected to varying ambient temperatures. The spatial temperature variation close to the sample (within 25 mm) is within approximately ​​​​±1°C of the average chamber temperature. The relative humidity can be manually controlled to within ±.7 percent RH. Automated control, complicated by a response lag, was within ±1 percent RH. Master of Science

Star-like lignin-poly(propylene oxide) copolymers were prepared by chain-extending steam exploded lignins (tulipifera liriodendron) with propylene oxide and by subsequent endcapping with ethylene oxide. Epoxidation of these copolymers was carried out with epichlorohydrin at room temperature, using KOH as oxyanion forming reagent. The epoxidized compounds were fractionated by solvent precipitation to remove poly(alkylene oxide) homopolymers and to prepare fractions of narrow molecular weight distributions. The epoxides were cross-linked with meta phenylene diamine yielding thermosets which were, depending on lignin content, either low modulus elastomers, or high modulus materials with considerable ductility. The modulus of elasticity was a strong and linear function of lignin content, whereby the highest value was 1100MPa (57% lignin). The curing reaction was of nth-order type, whereby the reaction order changed from close to one at the beginning of the curing reaction to 2, once the reaction becomes diffusion controlled. Curing induced partial demixing of the lignin and poly(propylene oxide) phases which yielded a secondary structure where lignin rich domains in the order of 10 nm were interspersed in a matrix of lignin poor material. However, from TEM and ¹³C solid state cross-polarized NMR analyses it was evident that the domain structure was not that of a classical micro-phase separated copolymer with well defined phase boundaries, but rather had broad interphases. Additionally, the results of multifrequency dynamic mechanical thermal analysis showed that the lignin containing thermosets have very broad glass transition ranges which most likely were due to transitional phase inhomogeneities and provided these materials with good vibrational damping ability. Ph. D.

Mat conditions of temperature and gas pressure were measured in three locations for one conventional and four steam-injection press schedules used in the laboratory scale manufacture of aspen (Populus grandidentata and Populus tremuloides) flakeboard. Two resins, phenol formaldehyde and polymeric MDI, were used. Steam-injection press schedules varied from low steam input to high steam input by adjusting steam pressure, steam time, and the density range for steam-injection during press closing. Steam-injection rapidly raises mat core temperatures as compared to conventional pressing. Temperature and gas pressure were positively correlated with the amount of steam input. Flakeboard strength and dimensional stability properties were tested. Steam-injection pressing produced panels with superior dimensional stability as compared to conventional pressing. The high steam press schedule produced internal bond and shear strengths equal to the conventional press schedule for phenol formaldehyde. Medium steam press schedules produced superior internal bond and shear strengths to the conventional press schedule for polymeric MDI. The conventional press schedule produced superior static bending MOR strengths for both resins. A fluorescence microscope was interfaced with a digitizing image analysis system to measure resin penetration area on flakes recovered from inside of the mat. Wood anatomy was found to be the dominating factor in creating high variablity in resin penetration area measurements, as differences could not be detected due to the press schedules or resin type. Master of Science

The increasing demand on wood and wood products, and the simultaneously decreasing quality of wood as a raw material leads to the increasing significance of wood-based composites such as particleboard or flakeboard. The resulting mechanical and physical properties are to the large extend dictated by the densification of the wood component. To be able to predict the density of the material, the behavior of structural elements must be known. A theory developed for rigid plastic foams was modified and applied to the deformation of wood in transverse compression. A testing procedure for high strain compression over a range of temperatures was developed. In addition, a stochastic model for prediction of high strain behavior was developed. Wood of yellow poplar (Liriodendron tulipuera) was used as the experimental material. Master of Science

With the large number and diversity of materials available today, the ability of the manufacturer to control properties is critical for the success of a product in the market. Although we have little or no control over the engineering properties of solid wood, the potential for the design of material properties in composites is great. Large strides are presently being made in the design of non-veneer structural panels by using material science principles. However, a large gap in our knowledge of the composite system is in the understanding of how raw material properties and processing variables interact to influence the internal geometry and material properties of the components in situ. The ability to use production variables to control material properties of the composite is an extremely valuable tool. The goal of this research is to provide an understanding of how the heat and mass transfer inside a flakeboard during pressing, interacts with the viscoelastic behavior of individual flakes to influence density gradient formation and in situ flake properties. The specific objectives: l. To use observed changes in the temperature and gas pressure of the internal environment of panels during the pressing cycle to describe the composition of the gas phase. 2. To use the calculated composition of the gas phase and measured temperature for the internal environment as boundary conditions for a fundamental heat and mass transfer model to access changes in the temperature and moisture content of the wood component during pressing. 3. To use the temperature and moisture content relations above to qualitatively relate press conditions to the formation of density gradients through changes in the glass transition temperature of the amorphous polymers in wood. 4. To utilize micromechanical models of cellular materials in conjunction with linear viscoelasticity of polymers to develop a nonlinear viscoelasticity model for wood in transverse compression. The approach couples the viscoelastic behavior of the amorphous polymers in wood with the structure imposed by anatomy. These theories, if applicable to wood, can greatly simplify the study of many similar systems combining environmental conditions and mechanical properties. Ph. D.