Search

An abstract of the article "Technical Solutions to Improve Recovery of Scraps Derived From Treating Glass Packaging Waste" by Fernanda Andreola and colleagues is presented.

Waste generated in ceramic tiles manufacturing is not usually recycled inside the productive plant, but rather disposed to landfill. This paper deals with ceramic residues from polishing and glazing processes, as constituents for innovative blended cements. New binders made up of 75% CEM I 52.5 R and 25% residues were chemically, physically, and mechanically characterized with reference to EN 197-1 requirements and the results compared with ordinary Portland cement. Mechanical strength development and microstructure of the relevant mortar have been investigated up to 90 days of curing, and the behavior of polishing and glazing residues as cement constituents is reported. [ABSTRACT FROM AUTHOR]

Examines the nucleation and crystal growth of diopside Ca(Mg,Al)(Si,Al)[sub 2])[sub 6] crystals. Completion of crystallization; Assessment of the activation energy; Reduction on the volume of residue.

Examines the development of calcium aluminosilicate glass-ceramics from waste materials with iron oxides. Suitability of vitrification/devitrification techniques for recycling and exploitation; Implication for waste disposal problems; Range of crystallization activation energy values; Role of ions in the crystallization tendency.

The article discusses the provision concerning the budget of Italy which stipulates that no taxes or expenditures may be established by the law approving the budget nor may the law approving the budget amend existing legislation. The norms that discipline the compilation of the national budget of Italy are contained in Article 81 of the Constitution. This provision stipulates that no new taxes or expenditures may be established by the law approving the budget, nor may the law approving the budget amend existing spending legislation. The national budget is, therefore, an executive act with a pre-established content and a limited scope. In fact, during the thawing up of and debate on the budget, the government and Parliament may exercise their respective decision-making powers over an extremely limited area of spending. This provision does not permit the budget law to be used as an instrument of economic policy. In particular, the multiyear budget must, according to the new law, provide that the growth of current expenditures is matched by the growth of revenues and does not continue, as in the past, to expand the deficit. This new and more stringent norm on covering expenditure reinforces the already existing checks in the Italian Constitution.

This study proposes different manufacturing techniques (manual pelletization, powder pressing, and "shell scaffold") to obtain lightweight clay ceramics containing recovery raw materials. The sintering in an electrical furnace (1000 °C, 1 h processing time) was conducted by traditional firing from room temperature, for pressed and shell-scaffold samples, while the flash heating (i.e., samples directly put at 1000 °C) was used only for the pellets. The porous materials (porosity 40–80%), functionalized with nutrients (K and P) in amounts to confer the fertilizer capability, gave suitable results in terms of pH (6.7–8.15) and electrical conductivity (0.29–1.33 mS/cm). Thus, such materials can be considered as feasible lightweight clay ceramics, with a positive effect on the soil. These findings permit us to hypothesize a potential use in green roofs or in agronomic applications. [ABSTRACT FROM AUTHOR]

This paper presents an innovative application for spent coffee grounds (SCGs) used as filler for the formulation of lightweight clay ceramic aggregates (LWA). LWA can be used for urban and agricultural purposes as a sustainable solution. Spent coffee grounds were tested as a pore forming agent partially acting as a replacement for red clay in material formulation before firing. Substitutions of 10, 15, and 20 wt.% of red clay were tested. The properties of lightweight aggregates with 15 wt.% of SCGs were improved using a specifically tailored fertilizer glass due to its low pH and conductivity within the soil tolerance range. Packaging glassy sand, cattle-bone flour ash, and potassium carbonate were mixed and melted in order to obtain this glass, which when added to the clayey batch functionalized the aggregates by phosphorus and potassium nutrients. The results (in particular, porosity and bulk density) show that the lightweight aggregates obtained have interesting properties for possible uses both in urban (e.g., green roofs as a drainage layer) and agricultural purposes. Moreover, pH and conductivity are in line with the Italian Standard regarding soil amendment (D.lgs. 75/2010). In addition, several leaching tests were performed in a solution containing 2 vol.% citric acid (C6H8O7) to evaluate the release capacity not only of nutrients (P and K) but also to check the presence and release of heavy metals, such as lead (Pb), that may come from the glassy precursor. The results obtained showed that nutrients are efficiently released in 21 days (P = 87.73% and K = 25.74% of released percentage) and Pb release is under the standard threshold of 30 ppm. [ABSTRACT FROM AUTHOR]

The chemical, microstructural and mechanical characterization of novel lightweight composites produced by adding waste cork dust to a metakaolin-based geopolymeric matrix prepared by alkaline activation is presented. The alkaline activator solutions used for the reticulation of the 3D aluminosilicate network at room temperature are composed of NaOH and sodium silicate to maintain a low cost of the final composite. In this line, the research of the highest addition of waste, e.g. cork dust, is pursued starting from 1 and reaching a maximum content of 10 wt% over metakaolin. The chemical stability is evaluated in water as well as in HNO 3 or in H 2 SO 4 0.5 and 2.5 N solutions. The addition of cork does not affect the reticulation of the geopolymeric binder used as matrix, as is demonstrated by FT-IR and XRD analyses. The modification of the dense geopolymeric microstructure with the introduction of cork dust weakens the hardened composites that become more permeable to water and acid solutions increasing the weight loss after immersion and decreasing the mechanical resistance to compression. The mechanical performance of the hardened composite with 10 wt% of cork dust still seems to be sufficient for application as self-supporting thermal insulation panels. (195/200). [ABSTRACT FROM AUTHOR]

This work reports the results of an investigation aimed at the development of sintered glass‐ceramic tiles by the sinter‐crystallization of mixtures composed of aluminum slag and reclaimed packaging glass. The thermal behaviors of mixtures incorporating 50 and 60 wt% Al slag were established by differential thermal analysis (DTA). Green compacts were sintered in a temperature range of 800°C‐1050°C and then soaked for 10‐60 minutes. The mineralogical characterizations of the sintered materials were obtained by X‐ray diffraction (XRD). The achieved results indicated that the sintering of aluminum slag and packaging glass reclaimed led to a glass‐ceramic material composed mainly of needle‐like crystals of wollastonite (CaSiO3). The bloating of samples during firing was evaluated according to a Cougny predictive diagram. After initial observations and according to bending strength characterizations, sintered tiles prepared from aluminum slag and glassy sand are appropriate for floor pavement and wall covering. [ABSTRACT FROM AUTHOR]

Italian pumice and volcanic lapillus scraps have been used in different percentages as alternative raw materials to foreign feldspars in porcelain stoneware mixtures. The aim of this work was to create naturally colored support to limit the use of artificial dyes while maintaining the technical properties of the reference product. For this purpose, the significant presence of chromophores (Fe and Ti in particular) in by-products from extraction of Italian volcanic pumice and lapillus was exploited. The work was carried out in collaboration with a company: the products were made on a laboratory scale and then they were glazed and fired within the industrial production cycle (48 min, 1210 °C). The resulting slip and the fired samples were characterized by measuring the efflux time, density, linear shrinkage, water absorption and tensile strength to evaluate the technological performance. In addition, thermogravimetric analysis (TG), differential thermal analysis (DTA), and optical and mechanical dilatometry were performed to study the thermal behavior of the formulations. The obtained products could be classified as porcelain stoneware and belong to the BIa group (WA 0.5%, B.S.>35 MPa) in accordance with UNI EN 14411 ISO 13006. [ABSTRACT FROM AUTHOR]

Glass with different chemical compositions, deriving from separate collection, has been used as fine aggregate to formulate cementitious mortars, substituting natural sand. Glass coming from cathode-ray tube monitors, fluorescent lamps, and crystal glass (from production of home décor items) along with glass deriving from soda-lime glass containers, which has been taken as a reference, have been investigated. Glass solubility has been determined in alkaline environment similar to the one inside the cementitious composite. Alkali silica reaction has been tested on glass modified cement mortar in different accelerated conditions. Mortar samples containing glass with chemical composition different with respect to soda-lime glass are subjected to alkali silica reaction. This behaviour is largely dependent on the ratio among modifier and stabilizer oxides in the glass. The same ratio affects glass solubility and consequently composition of expanding gels when alkali silica reactions take place. [ABSTRACT FROM AUTHOR]

In the present work, a statistical optimization of a sustainable coating for core–shell NPK (Nitrogen–Phosphorus–Potassium) fertilizers was investigated. The environmental green coating was enriched in nitrogen using a biomass and renewable source, namely the nitrogen rich fraction of black soldier fly larvae (BSFL) (Hermetia Illucens, Diptera: Stratiomyidae) reared on vegetable waste. A rational approach was proposed with the aim of calculating the best formulation of the coating, considering both its manufacturing behavior, such as adhesion to the core, and its physical properties, such as homogeneity or plasticity. From a circular economy perspective, together with the nitrogen-rich fraction from BSFL (from 51 to 90 wt.%), water and glycerol were considered for the coating formulation in different proportion: from 10 to 32 wt.% and from 0 to 17 wt.% respectively. The Design of Experiments technique was implemented to limit the total number of tests for the coating formulation (18 tests). ANOVA was employed, with the aim of obtaining mathematical models to derive a better precise and objective formulation. The results show that the use of glycerol can be avoided, as well as only a limited amount of water (11 wt.%) is necessary to obtain an optimized coating formulation, thereafter, satisfying the more relevant technological and physical properties for the coating manufacturing. [ABSTRACT FROM AUTHOR]

A class of inorganic binders, also known as geopolymers, can be obtained by alkali activation of aluminosilicate powders at room temperature. The process is affected by many parameters (curing time, curing temperature, relative humidity etc.) and leads to a resistant matrix usable for inertization of hazardous waste. In this study an industrial liquid waste containing a high amount of chromium (≈2.3 wt%) in the form of metalorganic salts is inertized into a metakaolin based geopolymer matrix. One of the innovative aspects is the exploitation of the water contained in the waste for the geopolymerization process. This avoided any drying treatment, a common step in the management of liquid hazardous waste. The evolution of the process - from the precursor dissolution to the final geopolymer matrix hardening - of different geopolymers containing a waste amount ranging from 3 to 20% wt and their capability to inertize chromium cations were studied by: i) the leaching tests, according to the EN 12,457 regulation, at different curing times (15, 28, 90 and 540 days) monitoring releases of chromium ions (Cr(III) and Cr(VI)) and the cations constituting the aluminosilicate matrix (Na, Si, Al); ii) the humidity variation for different curing times (15 and 540 days); iii) SEM characterization at different curing times (28 and 540 days); iv) the trend of the solution conductivity and pH during the leaching test; v) the characterization of the short-range ordering in terms of T O T bonds (where T is Al or Si) by 29 Si and 27 Al solid state magic-angle spinning nuclear magnetic resonance (ss MAS NMR) for geopolymers containing high amounts of waste (10–20% wt). The results show the formation of a stable matrix after only 15 days independently on the waste amount introduced; the longer curing times increase the matrices stabilities and their ability to immobilize chromium cations. The maximum amount of waste that can be inertized is around 10 wt% after a curing time of 28 days. [ABSTRACT FROM AUTHOR]

Recycling corundum abrasive powder in metakaolin-based geopolymer formulations is proposed to reduce the amount of waste to be treated or disposed of in landfills, allowing to decrease ecological damage as well as to reduce transport costs for removal. The addition of waste corundum, as an important source of Al2O3, has proved to increase the slight ionic conductivity of the leachate solution obtained after immersion in water of samples at 28 d of curing at room temperature. With the same curing conditions, the geopolymerization process has not been disturbed as evidenced by the FT-IR peak shift and XRD patterns. It was recorded a decrease in resistance to compression of the consolidated geopolymers of about 5% with 10 wt% addition and of about 77% with the addition of 20 wt% of waste corundum. In any case, the waste abrasive powder does not release heavy metals when added to a geopolymeric formulation based on MK, NaOH, and Na-silicate, and does not show relevant antibacterial properties, indicating the formation of a stable and safe final product with a ceramic-like appearance. [ABSTRACT FROM AUTHOR]

Abstract: Cleaned Cathode Ray Tube (CRT) (panel and funnel) waste glasses produced from dismantling TV and PC colour kinescopes were used to prepare glass foams by a simple and economic processing route, consisting of a direct heating of glass powders at relatively low temperatures (600–800°C). This study reports on the feasibility of producing glass foams using waste egg shells as an alternative calcium carbonate-based (95wt%) foaming agent derived from food industry. The foaming process was found to depend on a combination of composition, processing temperature and mixture of raw materials (glass wastes). Hot stage microscopy (HSM), X-ray diffraction (XRD) and scanning electron microscopy (SEM) were used to characterize foams and evaluate the foaming ability and the sintering process. The experimental compositions allowed producing well sintered glass foams with suitable properties for some functional applications with environmental benefits such as: (1) reduced energy consumption because of the low heat treatment temperatures used; and (2) materials produced exclusively from residues. [Copyright &y& Elsevier]

This work focused on obtaining a porcelain stoneware body containing only Italian raw materials. The starting mixtures differed in the feldspathic fraction, one pumice-based and one lapillus-based. German ball clay was gradually replaced by Italian kaolinitic clay. The influence of Italian kaolinitic clay on the technical and aesthetic properties of the final product was analyzed by comparing it with the references. The work was carried out in collaboration with a ceramic company which allowed the tile production process to be simulated in the laboratory and fired in an industrial kiln using the production cycle (48 min, 1210 °C). Ceramic bodies were characterized in order to evaluate technological performance by measuring efflux time and density of slip, flexural strength on green, linear shrinkage and water absorption in vacuum on fired samples. Mineralogical, microstructural (ESEM) and colorimetric analyses were also performed on the fired samples. Efflux time and density are processing parameters; these were in line with the reference in the lapillus-based bodies with kaolinitic clay replacement rates of 100%; in the case of the pumice-based bodies, they were considered acceptable only for replacements of 25%. The lapillus-based body showed a microstructure similar to that of porcelain stoneware. Vacuum water absorption values were better in lapillus-based formulations than in pumice-based formulations but showed higher linear shrinkage values for 100% replacements. According to UNI EN 14411 ISO 13006, some of the products obtained can be classified as porcelain stoneware (group BIa). • Italian kaolinitic clay replaced German ball clay in a porcelain stoneware support. • Clays are similar in quartz and kaolinite content, but ball clays have more illite. • The Lapillus-based support permitted the total replacement of German ball clay. • The Pumice-based support permitted up to 25% replacement of German ball clay. • The closed porosity of the fired product is increased by adding kaolinitic clay. [ABSTRACT FROM AUTHOR]

Particulate composites based on poly(lactic acid) (PLA) and poly(butylene succinate) (PBS) biopolymers have been formulated. Silver skin (SSK), the by‐product derived from the roasting of coffee beans, has been milled to micrometric size and added up to a 30 wt% of loading, without any previous treatment. The dynamic mechanical properties of the composites have been investigated, as well as the stability toward UV and IR radiation. The filler improves some mechanical properties such as the elastic modulus (E′) mostly in PBS. Photoaging experiments demonstrate that SSK, due to its polyphenols content and antioxidant activity, is able to protect both PLA and PBS from UV degradation, highlighting an added value of SSK waste‐based composites. [ABSTRACT FROM AUTHOR]

Highlights: [•] Incinerator bottom ash can substitute in high percentage metakaolin for producing geopolymers. [•] Standard alkali activation at room temperature was successfully attained. [•] The amount of reactive aluminosilicate phase is important for geopolymers formulation. [•] Incinerator bottom ash can be a resource for saving conventional raw materials and energy. [Copyright &y& Elsevier]

Abstract: In this work the screening results of the scientific activity conducted on the possibility to use rice husk ash as silica precursor for ceramic pigments are reported. Ceramic pigments were synthesized by solid-state reactions and the color developed in a suitable ceramic glaze was investigated in comparison with the color developed by the pigments prepared from pure SiO2. [Copyright &y& Elsevier]