Search

The exponentially small splitting of separatrix, standard and whisker map approaches, Chirikov overlap criterion, renormalization group technique, incremental energy method are presented herein for analytic predictions of the onset of resonance in stochastic layers. An energy spectrum technique is also presented for the numerical prediction of such onset, and the numerical computation of layer width is introduced as well. The stochastic layers in a twin-well Duffing oscillator are predicted through several analytical approaches. The results show that the incremental energy method gives a better prediction compared to the numerical prediction. [ABSTRACT FROM AUTHOR]

Freestanding composite structures with embedded transition metal dichalcogenides (TMDCs) as the active material are highly attractive in the development of advanced electrodes for energy storage devices. Most 3D electrodes consist of a bilayer design involving a core–shell combination. To further enhance the gravimetric and areal capacities, a 3D trilayer design is proposed that has MoSe2 as the TMDC sandwiched in‐between an inner carbon nanotube (CNT) core and an outer carbon layer to form a CNT/MoSe2/C framework. The CNT core creates interconnected pathways for the e−/Na+ conduction, while the conductive inert carbon layer not only protects the corrosive environment between the electrolyte and MoSe2 but also is fully tunable for an optimized Na+ storage. This unique heterostructure is synthesized via a solvothermal‐carbonization approach. Due to annealing under a confined structural configuration, MoSe2 interlayer spaces are expanded to facilitate a faster Na+ diffusion. It is shown that an ≈3 nm thick carbon layer yielded an optimized anode for a sodium‐ion battery. The 3D porosity of the heterostructure remains intact after an intense densification process to produce a high areal capacity of 4.0 mAh cm−2 and a high mass loading of 13.9 mg cm−2 with a gravimetric capacity of 347 mAh g−1 at 500 mA g−1 after 500 cycles. [ABSTRACT FROM AUTHOR]

The article discusses that solar reflective and thermally emissive surfaces offer a sustainable way to cool objects under sunlight; and mentions that top layer absorbs appropriate visible wavelengths to show specific colors, while the underlayer maximizes the reflection of near-to-short wavelength infrared (NSWIR) light to reduce solar heating.

Breath acetone (BrAC) detection presents a promising scheme for noninvasive monitoring of metabolic health due to its close correlation to diets and exercise-regulated lipolysis. Herein, we report a Ti 3 C 2 T x MXene-based wireless facemask for on-body BrAC detection and real-time tracking of lipid metabolism, where Ti 3 C 2 T x MXene serves as a versatile nanoplatform for not only acetone detection but also breath interference filtration. The incorporation of in situ grown TiO 2 and short peptides with Ti 3 C 2 T x MXene further improves the acetone sensitivity and selectivity, while TiO 2 -MXene interfaces facilitate light-assisted response calibration. To further realize wearable breath monitoring, a miniaturized flexible detection tag has been integrated with a commercially available facemask, which enables facile BrAC detection and wireless data transmission. Through the hierarchically designed filtration-detection-calibration-transmission system, we realize BrAC detection down to 0.31 ppm (part per million) in breath. On-body breath tests validate the facemask in dynamically monitoring of lipid metabolism, which could guide dieter, athletes, and fitness enthusiasts to arrange diets and exercise activities. The proposed wearable platform opens up new possibility toward the practice of breath analysis as well as daily lipid metabolic management. A MXene-based wireless facemask is developed to automatically monitor breath acetone and indicate the lipid metabolism level influenced by diets and exercises. Basing on the evaluation of the hierarchically assembled MXene-decorated filter, MXene acetone sensor, and a detection tag, on-body tests are carried out to validate the facemask platform in real breath samples, which highlights its practice in daily healthcare. [Display omitted] [ABSTRACT FROM AUTHOR]

Cancer molecular imaging using specific probes designed to identify target proteins in cancer is a powerful tool to guide therapeutic selection, patient management, and follow-up. We demonstrated that icatibant may be used as a targeting probe for the significantly upregulated bradykinin B2R in colorectal cancer (CRC). Icatibant-based probes with high affinity towards bradykinin B2R were identified. The near-infrared (NIR) fluorescent dye conjugate MPA-PEG 3 -k-Icatibant and radioconjugate [99mTc]Tc-HYNIC-PEG 4 -Icatibant exhibited favourable selective and specific uptake in tumours when the subcutaneous and orthotopic colorectal tumour-bearing mouse models were imaged using NIR fluorescence imaging and Single-Photon Emission Computed Tomography–Computed Tomography (SPECT-CT), respectively. The tracer of [99mTc]Tc-HYNIC-PEG 4 -Icatibant accumulated in tumours according to biodistribution studies and peaked at 4 h with an uptake value of 3.41 ± 0.27%ID/g in HT29 tumour-bearing nude mice following intravenous injection (i.v.). The tumour-to-colorectal signal ratios were 5.03 ± 0.37, 15.45 ± 0.32, 13.58 ± 1.19 and 11.33 ± 1.73 1, 2, 4 and 6 h after tail-veil injection, respectively. Overall, in the wake of rapid and precise tumour delineation and penetration characteristics, icatibant-based probes represent promising high-contrast molecular imaging probes for the detection of bradykinin B2R. Icatibant, which is FDA-approved for hereditary angioedema (HAE) treatment, was labelled with a NIR dye MPA and radionuclide technetium-99 m. And we found that Icatibant-based probes exhibited high contrast over background signals and substantial tumour retention in subcutaneous and orthotopic colorectal cancer xenograft mouse models. [Display omitted] • Icatibant was found to target colorectal cancer. • Icatibant-based probes can detect in situ colorectal cancer with high tumour-to-background signal contrast. • Icatibant combined with radionuclides or potent cytotoxins should provide impetus in targeted therapies. [ABSTRACT FROM AUTHOR]

Synthesis of chemically stable non-precious-metal 3 d -block transition metal nanocatalysts for catalytic syngas conversion remains a great challenge, since the nanocatalysts are usually too active to remain stable under ambient conditions. In situ grown (N-doped) graphene-encapsulated Ni nanoparticles (NPs) (Ni@G, Ni@G-N) were successfully obtained by a simple route via an arc-discharge method. The Ni@G composite is composed of a graphene sheath and a metallic nickel core. The carbon layer can prevent the inner Ni NPs from being etched when they are exposed to air, H 2 O 2 or acid. Moreover, the as-prepared Ni@G exhibit excellent catalytic activity and methane selectivity and high stability in the methanation reaction. The catalytic performance can be further improved by doping nitrogen into the graphene shell. This method provides a good procedure for graphene encapsulation of non-precious-metal nanoparticles. [ABSTRACT FROM AUTHOR]

Humidity sensing-based wearable respiration monitoring systems have promising application prospects in providing the critical health information. Currently, due to the inherent flexibility and compatibility, fabric-based wearables have attracted tremendous interest in humidity sensing. Herein, we proposed a humidity sensor made from fabric coated with MXene and multi-walled carbon nanotubes (MWCNT). The sensor showed 265% response at 90% relative humidity (RH) and great response stability under deformation. The humidity response of MXene/MWCNT fabric (MC-fabric) sensor only varied 7% under stretch, which is greatly alleviated compared with pristine MXene fabric sensor (35% under stretch). The MC-fabric sensor, integrated into a mask, can accurately identify diverse human respiration patterns despite the deformation caused by motions. This work not only offers a facile modification strategy to enhance the sensing robustness under deformation, but also provides a feasible method for real-time breath analysis. • MXene and MWCNT was assembled on fabric for humidity detection. • The humidity response stability under deformation was improved by introduced MWCNT. • A smart mask was designed to implement wireless real-time respiration monitoring. • The electronic fabric can accurately track respiration under motion states. [ABSTRACT FROM AUTHOR]

• Ultrathin MXene/chitosan-quercetin multilayers were assembled for humidity detection. • Superior sensitivity and ultrafast response for water molecules was realized. • A fully wearable tag was made to implement human physiological monitoring. • The multilayers can track human respiration in real time and high resolution. Two-dimensional (2D) materials provides large surface area for H 2 O molecules adsorption and interaction, which has been utilized in humidity sensing and noninvasive monitoring of physiological events such as respiration. However, disadvantages including slow response or modest response hinder the accurate tracking of human breath. Hence, MXene, the new member of 2D material family with excellent hydrophilicity and tunable conductivity, has drawn much attention. In this work, the enhanced response of Ti 3 C 2 T x MXene to H 2 O molecules was achieved by onion-inspired assembling of Ti 3 C 2 T x MXene and chitosan-quercetin hybrid layer-by-layer. The chitosan-quercetin modified multilayers suppress the degradation of MXene in environment, exhibiting superior response (317 % at 90 % RH), ultrafast response (0.75 s), and long-term stability (more than 15 days). Integrated with a wireless flexible detecting tag, the multilayers realized wearable human respiration monitoring with robust, accurate tracking capacity, offering a facile and feasible method for versatile physiological monitoring based on humidity sensing. [ABSTRACT FROM AUTHOR]

Diseases mediated by cytokine storms are often characterized by an overexuberant pace of pathogenesis accompanied by significant morbidity and mortality. Thus, near real-time (NRT) detections via a site-of-inflammation (SOI) sampling of proinflammatory cytokines are essential to ensure a timely and effective treatment of acute inflammations, which up to now, has not been fully possible. In this work, we proposed a novel NRT and SOI immunosensor using ZIF-8 signal amplification together with an off-on strategy. To achieve NRT detections via a SOI sampling, the body fluid of choice is the dermal interstitial fluid (ISF). The significant merits of ISF over blood are the quality, quantity and diversity of ISF-based biomarkers; the fluid is non-coagulating, making it feasible to perform multiple or continuous samplings and the sampling is minimally invasive. Our immunosensor requires only 5 μL of ISF to achieve a simultaneous detection of five highly potent proinflammatory cytokines: IL-6, IFN-γ, IL-1β, TNF-α, IP-10. We employed a microneedle array patch (MAP) together with a trifurcated nozzle pump to extract a mean volume of between 30 and 60 μL of ISF in 20 min. Under optimal conditions, the biosensor is capable of high-quality performance that exhibits a lower limit of detection (LOD) of 5.761 pg/mL over a wide linear range of 5.761 -3 ‒ 20.00 ng/mL. We believe our immunosensor for NRT detections via a SOI sampling of ISF-biomarkers offers new theranostic opportunities that may not be possible with blood-based biomarkers., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier B.V.)

Bacterial-driven dental caries and tooth discoloration are growing concerns as the most common oral health problems. Current diagnostic methods and treatment strategies hardly allow simultaneous early detection and non-invasive treatment of these oral diseases. Herein, a wearable multifunctional double network hydrogel combined with polyaniline and barium titanate (PANI@BTO) nanoparticles is developed for oral microenvironment visualized sensing and sonodynamic therapy. Due to the colorimetric properties of polyaniline, the hydrogel displays a highly sensitive and selective response for visualized sensing of oral acidic microenvironment. Meanwhile, the barium titanate in the hydrogel efficiently generates reactive oxygen species (ROS) under ultrasound irradiation, realizing non-invasive treatment in the oral cavity. Through bacterial elimination experiments and tooth whitening studies, the hydrogel can achieve the dual effect of effectively inhibiting the growth of cariogenic bacteria and degrading tooth surface pigments. Owing to the visualized sensing of the oral acidic microenvironment and efficient sonodynamic therapy function, the proposed hydrogel system offers a solution for the prevention of caries and tooth whitening, which is promising in developing the biomedical system targeting the simultaneous sensing and therapy for oral diseases., (© 2024 Wiley‐VCH GmbH.)

Nonsmall-cell lung cancer (NSCLC) is the most frequent type of lung cancer, with early surgical treatment proving vital for prolonged patient survival. However, precise visualization of NSCLC remains a challenge due to limited molecular imaging probes, the unique anatomical structure of the lungs, and respiratory movement interference. In this study, we investigated the potential utility of CD36, which is highly expressed in NSCLC, as an imaging target. A selective and water-soluble fluorescent probe, MPA-ABT-510, was successfully constructed by coupling ABT-510 with MPA, a near-infrared (NIR) fluorescent dye. Molecular docking analysis shows that MPA-ABT-510 possesses strong binding affinity to the CD36 protein, with specific hydrogen bond interactions at defined amino acid residues. In vitro assays reveals that the fluorescein isothiocyanate-labeled peptide ABT-510 specifically binds to the CD36-high expressing NSCLC cell lines H1299 and A549. In vivo imaging verifies that the MPA-ABT-510 efficiently accumulates in the tumor site with a distinct fluorescent signal. Ex vivo imaging revealed that tumor-to-lung fluorescence ratios for subcutaneous and orthotopic H1299 mouse models were 7.19 ± 0.73 and 1.91 ± 0.42, respectively, while those for A549 mice were 5.53 ± 0.64 and 1.77 ± 0.41, respectively. Biodistribution analysis demonstrated efficient MPA-ABT-510 uptake in H1299 and A549 liver metastases models with tumor-to-liver fluorescence ratios of 2.47 ± 0.48 and 2.19 ± 0.22, respectively. High MPA-ABT-510 accumulation was evident in A549 intestinal metastases models, as evidenced by tumor-to-colorectal fluorescence ratios of 4.27 ± 0.11. MPA-ABT-510 exhibits superior imaging capabilities with minimal safety concerns, so it is a promising candidate for NSCLC surgical navigation., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Inc. All rights reserved.)

Periodontitis, a chronic disease, can result in irreversible tooth loss and diminished quality of life, highlighting the significance of timely periodontitis monitoring and treatment. Meanwhile, hydrogen sulfide (H 2 S) in saliva, produced by pathogenic bacteria of periodontitis, is an important marker for periodontitis monitoring. However, the easy volatility and chemical instability of the molecule pose challenges to oral H 2 S sensing. Here, we report a wearable hydrogel-based radio frequency (RF) sensor capable of in situ H 2 S detection and antibacterial treatment. The RF sensor comprises an agarose hydrogel containing conjugated silver nanoparticles-chlorhexidine (AG-AgNPs-CHL hydrogel) integrated with split-ring resonators. Adhered to a tooth, the hydrogel-based RF sensor enables wireless transmission of sensing signals to a mobile terminal and a concurrent release of the broad-spectrum antibacterial agent chlorhexidine without complex circuits. With the selective binding of the AgNPs to the sulfidion, the RF sensor demonstrates good sensitivity, a wide detection range (2-30 μM), and a low limit of detection (1.2 μM). Compared with standard H 2 S measurement, the wireless H 2 S sensor can distinguish periodontitis patients from healthy individuals in saliva sample tests. The hydrogel-based wearable sensor will benefit patients with periodontitis by detecting disease-related biomarkers for practical oral health management., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

Despite recent advancements in colorectal cancer (CRC) treatment, the prognosis remains unfavorable primarily due to high recurrence and liver metastasis rates. Fluorescence molecular imaging technologies, combined with specific probes, have gained prominence in facilitating real-time tumor resection guided by fluorescence. Hepatocyte growth factor (HGF) is overexpressed in CRC, but the advancement of HGF fluorescent probes has been impeded by the absence of effective HGF-targeting small-molecular ligands. Herein, we present the targeted capabilities of the novel V-1-GGGK-MPA probe labeled with a near-infrared fluorescent dye, which targets HGF in CRC. The V-1-GGGK peptide exhibits high specificity and selectivity for HGF-positive in vitro tumor cells and in vivo tumors. Biodistribution analysis of V-1-GGGK-MPA revealed tumor-specific accumulation with low background uptake, yielding signal-to-noise ratio (SNR) values of tumor-to-colorectal >6 in multiple subcutaneous CRC models 12 h postinjection. Quantitative analysis confirmed the probe's high uptake in SW480 and HT29 orthotopic and liver metastatic models, with SNR values of tumor-to-colorectal and -liver being 5.6 ± 0.4, 4.6 ± 0.5, and 2.1 ± 0.3, 2.0 ± 0.5, respectively, enabling precise tumor visualization for surgical navigation. Pathological analysis demonstrated the excellent tumor boundaries discrimination capacity of the V-1-GGGK-MPA probe at the molecular level. With its rapid tumor targeting, sustained tumor retention, and precise tumor boundary delineation, V-1-GGGK-MPA merges as a promising HGF imaging agent, enriching the toolbox of intraoperative navigational fluorescent probes for CRC.

Despite advancements in colorectal cancer (CRC) treatment, the prognosis remains unfavorable for patients with distant liver metastasis. Fluorescence molecular imaging with specific probes is increasingly used to guide CRC surgical resection in real-time and treatment planning. Here, we demonstrate the targeted imaging capacity of an MPA-PEG 4 -N 3 -Ang II probe labeled with near-infrared (NIR) fluorescent dye targeting the angiotensin II (Ang II) type 1 receptor (AGTR1) that is significantly upregulated in CRC. MPA-PEG 4 -N 3 -Ang II was highly selective and specific to in vitro tumor cells and in vivo tumors in a mouse CRC xenograft model. The favorable ex vivo imaging and in vivo biodistribution of MPA-PEG 4 -N 3 -Ang II afforded tumor-specific accumulation with low background and >10 contrast tumor-to-colorectal values in multiple subcutaneous CRC models at 8 h following injection. Biodistribution analysis confirmed the probe's high uptake in HT29 and HCT116 orthotopic and liver metastatic models of CRC with signal-to-noise ratio (SNR) values of tumor-to-colorectal and -liver fluorescence of 5.8 ± 0.6, 5.3 ± 0.7, and 2.7 ± 0.5, 2.6 ± 0.5, respectively, enabling high-contrast intraoperative tumor visualization for surgical navigation. Given its rapid tumor targeting, precise tumor boundary delineation, durable tumor retention and docking study, MPA-PEG 4 -N 3 -Ang II is a promising high-contrast imaging agent for the clinical detection of CRC., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Masson SAS. All rights reserved.)

Hyaluronidase (HAase) is an important endoglycosidase involved in numerous physiological and pathological processes, such as apoptosis, senescence, and cancer progression. Simple, convenient, and sensitive detection of HAase is important for clinical diagnosis. Herein, an easy-to-operate multicolor visual sensing strategy was developed for HAase determination. The proposed sensor was composed of an enzyme-responsive hydrogel and a nanochromogenic system (gold nanobipyramids (AuNBPs)). The enzyme-responsive hydrogel, formed by polyethyleneimine-hyaluronic acid (PEI-HA), was specifically hydrolyzed with HAase, leading to the release of platinum nanoparticles (PtNPs). Subsequently, PtNPs catalyzed the mixed system of 3,3',5,5'-tetramethylbenzidine (TMB) and H 2 O 2 to produce TMB 2+ under acidic conditions. Then, TMB 2+ effectively etched the AuNBPs and resulted in morphological changes in the AuNBPs, accompanied by a blueshift in the localized surface plasmon resonance peak and vibrant colors. Therefore, HAase can be semiquantitatively determined by directly observing the color change of AuNBPs with the naked eye. On the basis of this, the method has a linear detection range of HAase concentrations between 0.6 and 40 U/mL, with a detection limit of 0.3 U/mL. In addition, our designed multicolor biosensor successfully detected the concentration of HAase in human serum samples. The results showed no obvious difference between this method and enzyme-linked immunosorbent assay, indicating the good accuracy and usability of the suggested method., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Austria, part of Springer Nature.)

Extracellular vesicles (EVs) are used by living cells for the purpose of biological information trafficking from parental-to-recipient cells and vice versa. This back-and-forth communication is enabled by two distinct kinds of biomolecules that constitute the cargo of an EV: proteins and nucleic acids. The proteomic- cum -genetic information is mediated by the physiological state of a cell (healthy or otherwise) as much as modulated by the biogenesis pathway of the EV. Therefore, in mirroring the huge diversities of human communications, the proteins and nucleic acids involved in cell communications possess seemingly near limitless diversities, and it is this characteristic that makes EVs so highly heterogeneous. Currently, there is no simple and reliable tool for the selective capture of heterogeneous EVs and the delivery of their undamaged cargo for research in extracellular protein mapping and spatial proteomics studies. Our work is a preliminary attempt to address this issue. We demonstrated our approach by using antibody functionalized liposomes to capture EVs from tumor and healthy cell-lines. To characterize their performance, we presented fluorescence and nanoparticle tracking analysis (NTA) results, TEM images, and Western blotting analysis for EV proteins. We also extracted dermal interstitial fluid (ISF) from healthy individuals and used our functionalized synthetic vesicle (FSV) method to capture EVs from their proteins. We constructed three proteomic sets [EV vs ISF, (FSV+EV) vs ISF, and (FSV+EV) vs EV] from the EV proteins and the free proteins harvested from ISF and compared their differentially expressed proteins (DEPs). The performance of our proposed method is assessed via an analysis of 1095 proteins, together with volcano plots, heatmap, GO annotation, and enriched KEGG pathways and organelle localization results of 213 DEPs.

Point-of-care testing methods currently utilize rapid, portable, inexpensive, and multiplexed on-site detection. Microfluidic chips have become a very promising platform with broad development prospects due to their breakthrough improvement in miniaturization and integration. However, the conventional microfluidic chips still have disadvantages, such as difficulty in fabrication processing, long production time and high cost, which hinder its applications in the fields of POCT and in vitro diagnostics. In this study, a capillary-based microfluidic chip with the characteristics of low cost and easy fabrication was developed for the rapid detection of acute myocardial infarction (AMI). Several short capillaries, which were already conjugated with the capture antibodies respectively, were connected by peristaltic pump tubes and then formed the working capillary. Two working capillaries were encapsulated in the plastic shell and ready for the immunoassay. Multiplex detection of Myoglobin (Myo), cardiac troponin I (cTnI) and creatine kinase-MB (CK-MB) were chosen to demonstrate the feasibility and analytical performance of the microfluidic chip, which requires rapid and accurate detection during diagnosis and therapy for AMI. The capillary-based microfluidic chip required tens of minutes to prepared, and its cost was less than $1. The limit of detection (LOD) was 0.5 ng/mL for Myo, 0.1 ng/mL for cTnI and 0.5 ng/mL for CK-MB respectively. The capillary-based microfluidic chips with easy fabrication and low cost hold promise for the portable and low-cost detection of target biomarkers., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier B.V. All rights reserved.)

Despite advancements in pancreatic cancer treatment, it remains one of the most lethal malignancies with extremely poor diagnosis and prognosis. Herein, we demonstrated the efficiency of a novel peptide GB-6 labeled with a near-infrared (NIR) fluorescent dye 3H-indolium, 2-[2-[2-[(2-carboxyethyl)thio]-3-[2-[1,3-dihydro-3,3-dimethyl-5-sulfo-1-(3-sulfopropyl)-2H-indol-2-ylidene]ethylidene]-1-cyclohexen-1-yl]ethenyl]-3,3-dimethyl-5-sulfo-1-(3-sulfopropyl)-, inner salt (MPA) and radionuclide technetium-99m ( 99m Tc) as targeting probes using the gastrin-releasing peptide receptor (GRPR) that is overexpressed in pancreatic cancer as the target. A short linear peptide with excellent in vivo stability was identified, and its radiotracer [ 99m Tc]Tc-HYNIC-PEG 4 -GB-6 and the NIR probe MPA-PEG 4 -GB-6 exhibited selective and specific uptake by tumors in an SW1990 pancreatic cancer xenograft mouse model. The favorable biodistribution of the tracer [ 99m Tc]Tc-HYNIC-PEG 4 -GB-6 in vivo afforded tumor-specific accumulation with high tumor-to-muscle and -bone contrasts and renal body clearance at 1 h after injection. The biodistribution analysis revealed that the tumor-to-pancreas and -intestine fluorescence signal ratios were 5.2 ± 0.3 and 6.3 ± 1.5, respectively, in the SW1990 subcutaneous xenograft model. Furthermore, the high signal accumulation in the orthotopic pancreatic and liver metastasis tumor models with tumor-to-pancreas and -liver fluorescence signal ratios of 7.66 ± 0.48 and 3.94 ± 0.47, respectively, enabled clear tumor visualization for intraoperative navigation. The rapid tumor targeting, precise tumor boundary delineation, chemical versatility, and high potency of the novel GB-6 peptide established it as a high-contrast imaging probe for the clinical detection of GRPR, with compelling additional potential in molecular-targeted therapy.

Printed flexible electronics have emerged as versatile functional components of wearable intelligent devices that bridge the digital information networks with biointerfaces. Recent endeavors in plant wearable sensors provide real-time and in situ insights to study phenotyping traits of crops, whereas monitoring of ethylene, the fundamental phytohormone, remains challenging due to the lack of flexible and scalable manufacturing of plant wearable ethylene sensors. Here the all-MXene-printed flexible radio frequency (RF) resonators are presented as plant wearable sensors for wireless ethylene detection. The facile formation of additive-free MXene ink enables rapid, scalable manufacturing of printed electronics, demonstrating decent printing resolution (2.5% variation), ≈30000 S m -1 conductivity and mechanical robustness. Incorporation of MXene-reduced palladium nanoparticles (MXene@PdNPs) facilitates 1.16% ethylene response at 1 ppm with 0.084 ppm limit of detection. The wireless sensor tags are attached on plant organ surfaces for in situ and continuously profiling of plant ethylene emission to inform the key transition of plant biochemistry, potentially extending the application of printed MXene electronics to enable real-time plant hormone monitoring for precision agriculture and food industrial management., (© 2023 Wiley-VCH GmbH.)

Surgical resection constitutes the first choice of treatment for colorectal cancer (CRC). Despite advancements in intraoperative navigation, there remains a considerable lack of effective targeting probes for the imaging-guided surgical navigation of CRC owing to their high heterogeneity. Hence, developing a suitable fluorescent probe to detect the specific types of CRC populations is crucial. Herein, we labeled ABT-510, a small, CD36-targeting thrombospondin-1-mimetic peptide overexpressed in various cancer types, with fluorescein isothiocyanate or near-infrared dye MPA. We found that fluorescence-conjugated ABT-510 exhibited excellent selectivity and specificity toward cells or tissues with high CD36 expression. The tumor-to-colorectal signal ratios were 11.28 ± 0.61 (95% confidence interval) and 10.74 ± 0.07 (95% confidence interval) in subcutaneous HCT-116 and HT-29 tumor-bearing nude mice, respectively. Moreover, high signal contrast was observed in the orthotopic and liver metastatic CRC xenograft mouse models. Furthermore, MPA-PEG 4 -r-ABT-510 exhibited an antiangiogenic effect via tube information assay with human umbilical vein endothelial cells. Overall, MPA-PEG 4 -r-ABT-510 presents rapid and precise tumor delineation characteristics, thereby making it a desirable tool for CRC imaging and surgical navigation.

Organic solar cells (OSCs) based on a bulk heterojunction structure exhibit inherent advantages, such as low cost, light weight, mechanical flexibility, and easy processing, and they are emerging as a potential renewable energy technology. However, most studies are focused on lab-scale, small-area (<1 cm 2 ) devices. Large-area (>1 cm 2 ) OSCs still exhibit considerable efficiency loss during upscaling from small-area to large-area, which is a big challenge. In recent years, along with the rapid development of high-performance non-fullerene acceptors, many researchers have focused on developing large-area non-fullerene-based devices and modules. There are three essential issues in upscaling OSCs from small-area to large-area: fabrication technology, equipment development, and device component processing strategy. In this review, the challenges and solutions in fabricating high-performance large-area OSCs are discussed in terms of the abovementioned three aspects. In addition, the recent progress of large-area OSCs based on non-fullerene electron acceptors is summarized.

The main function and biological processes of tissues are determined by the combination of gene expression and spatial organization of their cells. RNA sequencing technologies have primarily interrogated gene expression without preserving the native spatial context of cells. However, the emergence of various spatially-resolved transcriptome analysis methods now makes it possible to map the gene expression to specific coordinates within tissues, enabling transcriptional heterogeneity between different regions, and for the localization of specific transcripts and novel spatial markers to be revealed. Hence, spatially-resolved transcriptome analysis technologies have broad utility in research into human disease and developmental biology. Here, recent advances in spatially-resolved transcriptome analysis methods are summarized, including experimental technologies and computational methods. Strengths, challenges, and potential applications of those methods are highlighted, and perspectives in this field are provided., (© 2021 Wiley-VCH GmbH.)

Compressible energy devices have received increasing attention with the rapid development of flexible electronics and wearable devices due to their size adaptability and functional stability. However, it is hard to simultaneously achieve satisfactory energy density and mechanical stability for electrodes. Here an open-porous dual network sponge (DNS) with two networks of highly conductive carbon nanotubes and Li + -intercalating TiO 2 -B nanowires is synthesized and employed as compressible lithium ion battery electrodes. All 1D components inside the DNS mutually penetrate with each other to form two physically distinct but functionally coupling networks, endowing DNS excellent compressibility and stability. A prototype compressible lithium-ion battery (C-LIB) is also demonstrated, in which the DNS exhibits a specific capacity of >238 mAh g -1 under static 50% strain, and further in situ measurements show that under 1000 times of cyclic strains, DNS can charge and discharge normally maintaining a high capacity of 240 mAh g -1 and exhibits robustness to fast strain rates up to 500% min -1 . The dual network structure can be extended to design high-performance compliant electrodes that are promising to serve in future compressible and deformable electronics and energy systems., (© 2021 Wiley-VCH GmbH.)

Bladder cancer is characterized by its frequent recurrence and progression. Effective treatment strategies need to be based on an accurate risk stratification, in which muscle invasiveness and tumor grade represent the two most important factors. Traditional imaging techniques provide preliminary information about muscle invasiveness but are lacking in terms of accuracy. Although as the gold standard, pathological biopsy is only available after the surgery and cannot be performed longitudinally for long-term surveillance. In this work, we developed a microfluidic approach that interrogates circulating tumor cells (CTCs) in the peripheral blood of bladder cancer patients to reflect the risk stratification of the disease. In a cohort of 48 bladder cancer patients comprising 33 non-muscle invasive bladder cancer (NMIBC) cases and 15 muscle invasive bladder cancer (MIBC) cases, the CTC count was found to be considerably higher in the MIBC group compared with the NMIBC group (4.67 vs. 1.88 CTCs/3 mL, P=0.019), and was significantly higher in high-grade bladder cancer patients verses low-grade bladder cancer patients (3.69 vs. 1.18 CTCs/3mL, P=0.024). This microfluidic assay of CTCs is believed to be a promising complementary tool for the risk stratification of bladder cancer., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2021 Fu, Cheng, Chen, Xu, Chen, Tian, Xu, Sun, Neoh, Dai, Han and Jin.)

Embedding the functional nanostructures into a lightweight nanocarbon framework is very promising for developing high performance advanced electrodes for rechargeable batteries. Here, to realize workable capacity, core-shell (FeSe 2 /C) nanostructures are embedded into carbon nanotube (CNT) framework via a facile wet-chemistry approach accompanied by thermally induced selenization. The CNT framework offers 3D continuous routes for electronic/ionic transfer, while macropores provide adequate space for high mass loading of FeSe 2 /C. However, the carbon shell not only creates a solid electronic link among CNTs and FeSe 2 but also improves the diffusivity of sodium ions into FeSe 2 , as well as acts as a buffer cushion to accommodate the volume variations. These unique structural features of CNT/FeSe 2 /C make it an excellent host for sodium storage with a capacity retention of 546 mAh g -1 even after 100 cycles at 100 mA g -1 . Moreover, areal and volumetric capacities of 5.06 mAh cm -2 and 158 mAh cm -3 are also achieved at high mass loading 16.9 mg cm -2 , respectively. The high performance of multi-benefited engineered structure makes it a potential candidate for secondary ion batteries, while its easy synthesis makes it extendable to further complex structures with other morphologies (such as nanorods, nanowires, etc.) to meet the high energy demands., (© 2020 Wiley-VCH GmbH.)

A fully automated and accurate assay of rare cell phenotypes in densely-packed fluorescently-labeled liquid biopsy images remains elusive. Methods: Employing a hybrid artificial intelligence (AI) paradigm that combines traditional rule-based morphological manipulations with modern statistical machine learning, we deployed a next generation software, ALICE (Automated Liquid Biopsy Cell Enumerator) to identify and enumerate minute amounts of tumor cell phenotypes bestrewed in massive populations of leukocytes. As a code designed for futurity, ALICE is armed with internet of things (IOT) connectivity to promote pedagogy and continuing education and also, an advanced cybersecurity system to safeguard against digital attacks from malicious data tampering. Results: By combining robust principal component analysis, random forest classifier and cubic support vector machine, ALICE was able to detect synthetic, anomalous and tampered input images with an average recall and precision of 0.840 and 0.752, respectively. In terms of phenotyping enumeration, ALICE was able to enumerate various circulating tumor cell (CTC) phenotypes with a reliability ranging from 0.725 (substantial agreement) to 0.961 (almost perfect) as compared to human analysts. Further, two subpopulations of circulating hybrid cells (CHCs) were serendipitously discovered and labeled as CHC-1 (DAPI+/CD45+/E-cadherin+/vimentin-) and CHC-2 (DAPI+ /CD45+/E-cadherin+/vimentin+) in the peripheral blood of pancreatic cancer patients. CHC-1 was found to correlate with nodal staging and was able to classify lymph node metastasis with a sensitivity of 0.615 (95% CI: 0.374-0.898) and specificity of 1.000 (95% CI: 1.000-1.000). Conclusion: This study presented a machine-learning-augmented rule-based hybrid AI algorithm with enhanced cybersecurity and connectivity for the automatic and flexibly-adapting enumeration of cellular liquid biopsies. ALICE has the potential to be used in a clinical setting for an accurate and reliable enumeration of CTC phenotypes., Competing Interests: Competing Interests: The authors have declared that no competing interest exists., (© The author(s).)

Solar reflective and thermally emissive surfaces offer a sustainable way to cool objects under sunlight. However, white or silvery reflectance of these surfaces does not satisfy the need for color. Here, we present a paintable bilayer coating that simultaneously achieves color and radiative cooling. The bilayer comprises a thin, visible-absorptive layer atop a nonabsorptive, solar-scattering underlayer. The top layer absorbs appropriate visible wavelengths to show specific colors, while the underlayer maximizes the reflection of near-to-short wavelength infrared (NSWIR) light to reduce solar heating. Consequently, the bilayer attains higher NSWIR reflectance (by 0.1 to 0.51) compared with commercial paint monolayers of the same color and stays cooler by as much as 3.0° to 15.6°C under strong sunlight. High NSWIR reflectance of 0.89 is realized in the blue bilayer. The performances show that the bilayer paint design can achieve both color and efficient radiative cooling in a simple, inexpensive, and scalable manner., (Copyright © 2020 The Authors, some rights reserved; exclusive licensee American Association for the Advancement of Science. No claim to original U.S. Government Works. Distributed under a Creative Commons Attribution NonCommercial License 4.0 (CC BY-NC).)

3D electrode design is normally opted for multiple advantages, however, instability/detachment of active material causes the pulverization and degradation of the structure, and ultimately poor cyclic stability. Here, a dually protected, highly compressible, and freestanding anode is presented for sodium-ion batteries, where 3D carbon nanotube (CNT) sponge is decorated with homogeneously dispersed CoSe 2 nanoparticles (NPs) which are protected under carbon overcoat (CNT/CoSe 2 /C). The 3D CNT sponge delivers enough space for high mass loading while providing high mechanical strength and faster conduction pathway among the NPs. The outer amorphous carbon overcoat controls the formation of solid electrolyte interphase film by avoiding direct contact of CoSe 2 with electrolyte, accommodates large volume changes, and ultimately enhances the overall conductivity of cell and assists in transmitting electron to an external circuit. Moreover, the hybrid can be densified up to 11-fold without affecting its microstructure that results in ultrahigh areal mass loading of 17.4 mg cm -2 and an areal capacity of 7.03 mAh cm -2 along with a high gravimetric capacity of 531 mAh g -1 at 100 mA g -1 . Thus, compact and smart devices can be realized by this new electrode design for heavy-duty commercial applications., Competing Interests: The authors declare no conflict of interest., (© 2020 The Authors. Published by WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim.)

Background: The evaluation for surgical resectability of pancreatic ductal adenocarcinoma (PDAC) patients is not only imaging-based but highly subjective. An objective method is urgently needed. We report on the clinical value of a phenotypic circulating tumor cell (CTC)-based blood test for a preoperative prognostic assessment of tumor metastasis and overall survival (OS) of PDAC patients., Methods: Venous blood samples from 46 pathologically confirmed PDAC patients were collected prospectively before surgery and immunoassayed using a specially designed TU-chip™. Captured CTCs were differentiated into epithelial (E), mesenchymal and hybrid (H) phenotypes. A further 45 non-neoplastic healthy donors provided blood for cell line validation study and CTC false positive quantification., Findings: A validated multivariable model consisting of disjunctively combined CTC phenotypes: "H-CTC≥15.0 CTCs/2ml OR E-CTC≥11.0 CTCs/2ml" generated an optimal prediction of metastasis with a sensitivity of 1.000 (95% CI 0.889-1.000) and specificity of 0.886 (95% CI 0.765-0.972). The adjusted Kaplan-Meier median OS constructed using Cox proportional-hazard models and stratified for E-CTC < 11.0 CTCs/2 ml was 16.5 months and for E-CTC ≥ 11.0 CTCs/2 ml was 5.5 months (HR = 0.050, 95% CI 0.004-0.578, P = .016). These OS results were consistent with the outcome of the metastatic analysis., Interpretation: Our work suggested that H-CTC is a better predictor of metastasis and E-CTC is a significant independent predictor of OS. The CTC phenotyping model has the potential to be developed into a reliable and accurate blood test for metastatic and OS assessments of PDAC patients. FUND: National Natural Science Foundation of China; Zhejiang Province Science and Technology Program; China Scholarship Council., (Copyright © 2019 The Authors. Published by Elsevier B.V. All rights reserved.)

From a series of experimental measurements and supplemented by results from a computational model, we investigated the static and dynamic size dependent behaviors of a single-strand polycaprolactone (PCL) nanofiber. For the static bending, the fiber stiffness showed a dramatic increase as the fiber diameter is reduced and for the dynamic bending, the resonant frequency exhibited a very similar trend. Employing the strain gradient (SG) theory, we formulated a model that not only accurately captures the magnitude of the experimentally observed size dependent response but it is also, able to correctly predict the onset of the inverse square behavior. Both our experimental data and SG model results showed that the damping term is unaffected by the size-dependency. We introduced an experimentally calibrated fiber length scale parameter to predict the onset and rise of the size dependent response and an effective elastic modulus to characterize the stiffness increase. This understanding of the pronounced enhancement in nanofibers can be used to design a nanofibrous scaffold to keep its structural integrity intact against a sudden static pull of a seeded cell or when subjected to a dynamic loading environment from say, the pulsating peripheral blood., (Copyright © 2019 Elsevier Ltd. All rights reserved.)

Heterogeneous nanostructuring of MoSe 2 over a carbon nanotube (CNT) sponge as a free-standing electrode not only brings higher performance but also eliminates the need for dead elements such as a binder, conductive carbon, and supportive current collectors. Further, the porous CNT sponge can be easily compacted via an intense densification of the active material MoSe 2 to produce an electrode with a high mass loading for a significantly improved areal capacity. In this work, we present a tunable coating of MoSe 2 on a CNT sponge to fabricate a core-shell MoSe 2 @CNT anode. The three-dimensional nanotubular sponge is synthesized via a solvothermal process, followed by thermal annealing to improve crystallization. Structural and morphological studies revealed that MoSe 2 grew as a layered structure ( d = 0.66 nm), where numbers of layers can be controlled to yield optimized results for Li + storage. We showed that the 10-layer core-shell CNT@MoSe 2 hybrid sponge delivered a discharge capacity of 820.5 mAh g -1 after 100 cycles at 100 mA g -1 with a high cyclic stability and rate capability. Further, an ex situ structural and morphological analysis revealed that ionic storage causes a phase change in MoSe 2 from a crystalline to a partial amorphous state for a continuous increase in the capacity with extended cycling. We believe that the strategy developed here will assist users to tune the electrode materials for future energy-storage devices, especially how the materials are changing with the passage of time and their effects on the device performance.

Traditionally, liquid biopsy is a blood test involving the harvesting of tumor materials from peripheral blood. Tumor cells from non-blood body fluids have always been clinically available in cytological examinations but limited for use in differential diagnosis due to the low sensitivity of conventional cytopathology. With the recent significant progress in microfluidic and downstream molecular technologies, liquid biopsies have now evolved to include harvesting tumor cells and DNA fragments in all kinds of non-blood body fluids. This expansion into general body fluids presages the notion that liquid biopsy could soon be used in competition, as well as, in complementarity with tissue biopsy. Preliminary research of fluid-harvested tumor materials to spot early-stage tumors, monitor disease progression for metastasis and recurrence, and detect chemoresistance have been reported. To reflect the propagation of tumor cells in non-blood body fluids, we introduced the term Mobile Tumor Cells (MTCs), in lieu of the widely accepted term of circulating tumor cells (CTCs) resident in the bloodstream. Our review starts with a discussion on the clinical significance of MTCs, followed by a presentation of microfluidic techniques for MTC capture and various strategies for their identification. Hopefully, the phenotypic and genomic data acquired from harvested MTCs can be used to guide and improve cancer treatment decisions., (Copyright © 2017 Elsevier Ltd. All rights reserved.)

Background: Circulating endometrial cells (CECs) have been reported to be present in the peripheral blood of women with endometriosis (EM), providing clear and specific evidence of the presence of ectopic lesions. In this study, we established a method with a high detection rate of CECs, assessed the diagnostic value of CECs for EM and compared with serum CA125, and proposed a hypothesis for the pathogenesis of EM from the new perspective of CECs., Methods: The participants were enrolled prospectively from October 2015 to July 2016. The peripheral blood samples were collected from 59 participants, and the blood cells were isolated for immunofluorescence staining via microfluidic chips. The cells that were positive for vimentin/cytokeratin and estrogen/progesterone receptor and negative for CD45 were identified as CECs. The serum CA125 level was tested with electrochemiluminescence immunoassay., Results: The detection rate of CECs reached 89.5% (17/19) in the EM group, which was significantly higher than that of the control group (15.0% [6/40], P < 0.001) and was independent of menstrual cycle phases. Furthermore, a positive CEC assay detected 4/5 cases of Stage I-II EM. In contrast, a positive CA125 test had limited value in detecting EM (13/19, 68.4%) and detected only one case of Stage I-II EM., Conclusion: CECs are promising biomarkers for EM with great potential for a noninvasive diagnostic assay.

Heterogeneous inorganic nanotube structures consisting of multiwalled carbon nanotubes coated by long, continuous MoS 2 sheets with tunable sheet number are synthesized using a carbon-nanotube sponge as a template. The resulting 3D porous hybrid sponges have potential applications as high-performance freestanding anodes for Li-ion batteries with excellent specific capacity and cycling stability., (© 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)