Search

• 72% − 80% of fibre was recovered from disposable coffee cups. • 2% and 3% consistency shredded cups required > 100 kWh/tonne to repulp with 3 refiner passes. • Pulp quality did not significantly diminish after repulping using a single-disk refiner. Over 64 billion paper-plastic laminate (PPL) coffee cups are consumed between the United States and Canada annually, the majority accumulating in landfills due to a hydrophobic plastic inner-lining. Recycling can mitigate environmental damage and provide economic value from repurposed products. We found that standard repulping methods were insufficient to separate fiber from plastic due to the low intensity of treatment. To increase process intensity, we mechanically refined shredded PPL coffee cups and Kraft eucalyptus sheets (control) at 2%, 3%, and 4% consistencies with three passes to determine the energy required to separate fibers from plastic and the effects on fiber quality. 2% and 3% consistency PPL cups measured under 40 kWh/tonne of input material for one refiner pass and ∼ 80 kWh/tonne for 4% consistency PPL cups. Recovered fiber fraction totaled 87.7%, 85.3%, and 80.5% of input mass of Kraft eucalyptus and 72.3%, 72.6%, and 79.6% of input mass of PPL cups at 2%, 3%, and 4% consistency, respectively. Fines content of PPL cups jumped from 8% pre-refining to ∼ 30% post-refining while Kraft eucalyptus fibers were unaffected, suggesting that breaking the plastic-fiber bonds results in fines generation. Mean fiber length of PPL cups slightly decreased with consistency and tensile strength improved. Freeness decreased with consistency only in PPL cup samples. These results demonstrate a low energy requirement to effectively separate fiber and plastics in PPL cups as well as minimal impact on fiber quality using existing refining technology, and provides an estimate of the financial costs of local recycling efforts. [ABSTRACT FROM AUTHOR]

The cleaning of particles from smooth and rough paper surfaces using a high-speed CO2 snow jet was investigated. The measurements included characterization of the jet properties, determination of the cleaning efficiency, and evaluation of any possible adverse effects. The method was compared with nitrogen jet cleaning and dry cleaning by commercial materials. The results showed that the CO2 snow jet is able to effectively remove particles from the paper surface and did not cause any observable degradation. The CO2 snow jet cleaning compared with the mechanical dry cleaning showed similar effectiveness without any adverse effects on the paper surface. It was proved that the CO2 snow technique is a suitable method for cleaning common types of paper materials. [ABSTRACT FROM AUTHOR]

• Artificial light radiation is a viable tool for paper documents bleaching. • Artificial light bleaching does not produce any physico-chemical change in paper. • Artificial light bleaching reduces the yellowing of paper in short and long term. • Paper is physico-chemical and optically deteriorated by hydrogen peroxide. This study offers a new tool to restorers to bleach paper documents: artificial light radiation (ALR). It is a controlled method that is an alternative to other highly aggressive procedures that have been applied to cellulose based media. Its main novelty is its intrinsic lighting characteristics which guarantee uniformity and avoid heating the paper. The results of testing this new tool were compared to those of bleaching with hydrogen peroxide (H 2 O 2). Each of the two methods was applied to five different types of widely used paper: Arches and Somerset (brands serving for engraving and digital printing), Ingres (drawing), press-type (magazines and newspapers) and Bible-type (historical documents). Once characterised by physico-mechanical, chemical and optical parameters (grammage, thickness, specular gloss, optical properties, air permeance, tensile properties, determining the pH of both surface and aqueous extracts), the different papers were bleached by the two methods according to pre-established criteria. Finally, to determine the evolution and effects of the two treatments, the papers were subjected to accelerated ageing. [ABSTRACT FROM AUTHOR]

Purpose: We aimed to test the accommodative lag and mechanical tension theories for myopia by assessing the influence of the lag of accommodation on axial elongation by using three different near targets that are known to influence the accommodative response differently. Methods: Forty‐two young adults were recruited for the study. Axial length was measured using a non‐contact biometer, before and immediately after a 15 minute visual task, with one of the three near targets placed 20 cm from the eye: reading text from a paper, reading text from a smartphone and watching a video on a smartphone. The accommodative response was determined using an open‐field autorefractor while the participants viewed the near target monocularly. Results: Lag of accommodation was significantly different for the three tasks: watching a video (mean ± standard error of the mean [SEM] 0.92 ± 0.10 D); reading text on the smartphone (0.59 ± 0.08 D); and reading text on paper (0.24 ± 0.09 D). There was a significant (p < 0.05) increase in axial length after reading text from a paper (10.5 ± 1.9 µm after 15‐min) and reading text from a smartphone (5.2 ± 2.7 µm), but not after watching a video on a smartphone (−0.5 ± 1.7 µm, p = 0.47). Vitreous chamber depth increased significantly more with the reading tasks compared with watching a video (reading text from a paper and smartphone: 33.9 ± 4 µm and 31.7 ± 4 µm vs. watching a video on a smartphone: 14.6 ± 5 µm, p = 0.001). Conclusion: Greater changes in axial length associated with the low lag of accommodation failed to support the theory that lag of accommodation during visual tasks could be the trigger for axial elongation. Reading on paper and smartphone at the closest reading distance may stimulate high accommodative demand and axial elongation as a consequence, possibly due to increased "ciliary muscle tension" during accommodation. [ABSTRACT FROM AUTHOR]

A lignin-based PU coating was prepared for paper-based green packaging. Two representative diisocyanate were used to prepare the coatings. Due to the rigid aromatic, the physical properties of the TDI system reached the maximum below the lignin content of 40%. The HDI that contains flexible aliphatic chains alleviated the brittleness of coating, and it showed physical advantages when the lignin content was more than 50%. Owing to the high lignin content, the coating presented enhanced thermal stability. After coated with the lignin-based PU coatings, the dry tensile strength of coated paper was improved by 126%. Amazingly, the wet strength was increased from 0.31 to 12.6 MPa with an improvement nearly 40 times. Based on the coordination of lignin, Ag+ was introduced into the PU matrix, which imparted the coating with excellent antibacterial ability. The colony forming units of E. coli and S. aureus were both less than 1. However, no inhibition halo was observed, which indicated that the Ag was firmly anchored on the coating and the antibacterial ability is only available when the bacterial contact the coating surface. The lignin-based PU coating with favorable sustainability and properties shows great potential in paper-based green packaging fields. The prepared PU coating with high lignin content and firmly anchored Ag+ exhibits outstanding physical properties, thermal stability, and antibacterial property, which makes it an ideal candidate to be used in paper-based green packaging. [Display omitted] [ABSTRACT FROM AUTHOR]

The article presents the discussion on Andie Tucher. Topics include papers going to use as primary sources from over three hundred years of journalism history; newspapers and magazines becoming closely associated with identifying as fake journalism; and checking the veracity of journalistic reporting or countering dominant media narratives prior to the age of social media.

In this paper, the concepts of n-sequence prime ideal and n-sequence quasi prime ideal are introduced. Some properties of such ideals are investigated. The relations between n-sequence prime ideal and each of primary ideal, n-prime ideal, quasi prime ideal, strongly irreducible ideal, and (k, m) closed ideal, are studied. Also, the ideals of a principal ideal domain are classified into quasi prime ideals and n- sequence quasi prime ideals. [ABSTRACT FROM AUTHOR]

Iron gall Inks corrosion causes paper degradation (browning, embrittlement) and treatments were developed to tackle this issue. They often include resizing with gelatin to reinforce the paper and its cellulosic fibers (of diameter approx. 10 µm). This work aimed at measuring the distribution of ink components at the scale of individual paper fibers so as to give a better understanding of the impact of gelatin (re-)sizing on iron gall ink corrosion. For this purpose, scanning transmission X-ray microscopy (STXM) was used at the Canadian light source synchrotron (CLS, Saskatoon). This technique combines nano-scale mapping (resolution of 30 nm) and near edge X-ray absorption fine structure (NEXAFS) analysis. Fe L-edge measurements enabled to map iron distribution and to locate iron(II) and iron(III) rich areas. N K-edge measurement made it possible to map gelatin distribution. C K-edge measurements allowed mapping and discrimination of cellulose, gallic acid, iron gall ink precipitate and gelatin. Three fibers were studied: an inked fiber with no size, a sized fiber that was afterwards inked and an inked fiber sprayed with gelatin. Analysis of gelatin and ink ingredients distribution indicated a lower amount of iron inside the treated cellulosic fiber, which may explain the beneficial effect of gelatin on iron gall ink corrosion. [ABSTRACT FROM AUTHOR]

Smart, environmentally friendly alternatives, i.e., frankincense and rice starch, are recommended for usage in modern paper conservation processes during the re-sizing process treatments. Different concentrations of frankincense and rice starch were applied to paper samples before and after ageing. Multiple analysis methods were performed to ensure the effectiveness of these materials. Promising results were found, but at varying degrees according to the type and concentration of the materials. Scanning electron microscopy illustrated that the frankincense particles were completely absorbed into the cell walls after ageing. Results indicated that there was no considerable change in pH before and after treatment or ageing; the best results for decreasing the acidity utilized a treatment with a mixture of frankincense and rice starch in a 2 to 1 ratio (F2S1). Fourier transform infrared spectroscopy illustrated an increased CH2 region and decreased OH stretching as a result of the bonds formed from the starch and crystals formed by frankincense, which agreed with the increased coating and strength of the paper fibers. The total color change values of all the treated samples after ageing were less than 4.5. Frankincense was found to provide strength in supporting wood fibers. [ABSTRACT FROM AUTHOR]

The overall usefulness of the bursting energy absorption (BEA) was studied for a better analysis of paper strength properties. Additionally, the changes of the BEA during more complex deformations of paper products, e.g., preliminary or simultaneous tensile and burst, were determined. For the purpose of the research, an experimental setup was designed. The results showed that the correlation between BEA and bursting strength was linear, but the proportionality strongly depended on paper grade. Thus, a more accurate method to characterize the bursting resistance (BR) of paper was proposed. The BR parameter is described by the three following parameters: average bursting strength, average bursting energy absorption, and the slope of the fitted linear regression curve (relationship between the bursting energy absorption and the bursting strength). This method revealed new mechanical behaviors of papers related to their preloading. [ABSTRACT FROM AUTHOR]

[Display omitted] With the rapid development of wearable intelligent devices, low-cost wearable strain sensors with high sensitivity and low detection limit are urgently demanded. Meanwhile, sensing stability of sensor in wet or corrosive environments should also be considered in practical applications. Here, superhydrophobic microcracked conductive paper-based strain sensor was fabricated by coating conductive Ti 3 C 2 T x MXene on printing paper via dip-coating process and followed by depositing superhydrophobic candle soot layer on its surface. Owing to the ultrasensitive microcrack structure in the conductive coating layer induced by the mismatch of elastic modulus and thermal expansion coefficient between conductive coating layer and paper substrate during the drying process, the prepared paper-based strain sensor exhibited a high sensitivity (gauge factor, GF = 17.4) in the strain range of 0–0.6%, ultralow detection limit (0.1% strain) and good fatigue resistance over 1000 cycles towards bending deformation. Interestingly, it was also applicable for torsion deformation detection, showing excellent torsion angle dependent, repeatable and stable sensing performances. Meanwhile, it displayed brilliant waterproof, self-cleaning and corrosion-resistant properties due to the existence of micro/nano-structured and the low surface energy candle soot layer. As a result, the prepared paper-based strain sensor can effectively monitor a series of large-scale and small-scale human motions even under water environment, showing the great promising in practical harsh outdoor environments. Importantly, it also demonstrated good applicability for spatial strain distribution detection of skin upon body movement when assembled into electronic-skin (E-skin). This study will provide great guidance for the design of next generation wearable strain sensor. [ABSTRACT FROM AUTHOR]

The ash condensation ability of the cigarette paper is an important factor affecting the cigarette grades. In this study, we put forward an effective method of improving this ability. Xanthan gum was successfully synthesized, applied as an ash integrator in the dip-coating process of cigarette paper production, and showed good performance. Cationic guar gum, cellulose phosphate and Hydroxyapatite (HAP) have been added in the pulp and showed better performance of the ash condensation property. The ash become much whiter and the scatter of the ash have been suppressed. Moreover, the further addition of HAP would result in a worse combustion efficiency, leading to the burning out of the cigarette in early time. [ABSTRACT FROM AUTHOR]

Poor response rate, self-selection bias, and item noncompletion negatively impact the generalization of results from surveys. This study examined differences in these factors between a paper and online survey among allied health clinicians. Clinicians within a large local health district were initially invited to complete the Research Capacity in Context Tool online via an e-mail link. Following a lower-than-expected response rate, potential selection bias, and item noncompletion, the survey was readministered in paper form to the same cohort of clinicians 6-12 months later. The response rate to the paper survey was higher than to the online survey (27.6% vs. 16.5%). Selection biases were evident, characterized by seniority and discipline: Junior clinicians responded at rates significantly less than expected to the online survey but as expected to the paper survey. Occupational therapists, speech pathologists, and podiatrists responded more highly to the online survey, while other disciplines responded more highly to the paper survey. The rate of item noncompletion was higher for online than paper survey (6.72% vs. 3.8% questions not completed, respectively), with patterns of noncompletion also differing. These data suggest paper surveys are likely to produce less biased and more generalizable data from allied health clinicians. [ABSTRACT FROM AUTHOR]

A primary objective of a distributed storage system is to reliably store huge amounts of source data for long periods of time using a large number of high storage capacity nodes. Storage nodes are prone to permanent failures, where such node failures cause all stored data to be permanently lost, and failed nodes are replaced with nodes that initially store no data. To maintain recoverability of the source data as storage nodes fail and are replaced, a total amount of storage capacity that is larger than the source data size is allocated to store the source data, and a repairer continually reads data from and writes data to the storage nodes as they fail and are replaced. We prove information-theoretic lower bounds on the rate at which a repairer reads data from the storage system as a function of the rate at which nodes fail and the amount by which the allocated storage capacity exceeds the source data size. These lower bounds hold for any repairer, i.e., any repairer that does not read data at or above the lower bound rate will provably not maintain recoverability of the source data. The bounds are provably tight asymptotically as the number of storage nodes grows and the allocated storage capacity approaches the source data size. [ABSTRACT FROM AUTHOR]

The electrochemical literature describes a plethora of devices for various applications. Design and development of such paper‐based analytical device(PAD) for sensing applications is paramount of interest. In this work, a PAD was developed using common office‐hold items like paper, pencil, crayons and scotch tape. On a paper, a three‐electrode system was developed by simple drawing with pencils, and the accessible area was confined by creating a hydrophobic barrier using color crayons. The newly developed PAD can hold a low‐dead volume of 25 μL for the analysis and is sealed at the bottom using scotch tape. In our preliminary approach, uric acid (UA), a critical biomarker, was demonstrated as a model analyte for the application of the developed PAD as an electrochemical sensor. The sensor exhibited better analytical performance for UA sensing in a wide range (0.1–1 mM) with appreciable reproducibility, sensitivity (0.3×10−3 A M−1) and selectivity over common interferents (ascorbic acid, urea and glucose). Furthermore, the developed electroanalytical approach was validated by testing the UA in non‐invasive bio‐sample (human urine). Such a cheap, portable, disposable, biocompatible, eco‐friendly and fully‐drawn PAD paves the way for the development of affordable 'lab on paper' devices for a wide range of bioanalytical applications. [ABSTRACT FROM AUTHOR]

Ultrasonic welding is a serious candidate in the development of methods to assemble papers and paperboards without using additional substances. However, the ultrasonic welding of papers remains a technological challenge considering the low weldability of lignocellulosic materials. This study aims to investigate on the ultrasonic welding process applied to papers in order to identify the processing conditions which favor the formation of strong welded joints. To reach such purpose, an experimental strategy was developed by combining the characterization of welded materials and the monitoring of process parameters. Experimentations were performed using a reference paper displaying a good weldability to specifically highlight the contribution of process parameters. Results indicate that the process is highly sensitive to vibration amplitude, power supplied by the high frequency generator, and sample thickness. Power seems to be a reliable indicator of the severity of the process. A strong decrease in the strength of the welded joints is observed when working with low thicknesses. It seems that the layers coated on top of papers are the main part of the material contributing in the development of adhesion at the welding joint. Overall, instrumenting the device has led to a better understanding of the ultrasonic welding of papers. [ABSTRACT FROM AUTHOR]

Paper flowers are frequently, for example as indoor decorations and in wedding bouquets. But these traditional paper flowers can only maintain static conditions, greatly affecting their sensory effects, vividness, and appreciation. The design of novel paper flowers with dynamic shape deformation could effectively broaden the application of paper flowers. Here, inspired by Chinese calligraphy, a novel polyvinyl butyral (PVB)/carbon/cellulose composite (PCC) magic paper with a sandwiched structure is prepared. The hygroscopicity difference between hydrophobic PVB and hydrophilic cellulose layer endows the PCC paper with humidity responsiveness, and the maximum bending angle is up to 91.4° upon exposure to humidity environment. Carbon in the interlayer with strong light–heat conversion capacity could further accelerate water desorption and deformation speed, resulting in highly sensitive light responsiveness. The recovery time of PCC paper from maximum bending to the original flat state is shorter than 1 s. The PCC paper has good flexibility and processability, which can be cut and assembled into flowers with different shapes, and these unique magic flowers could freely bloom and furl upon external stimulus. All these results indicate that PCC paper has great potential in the production of magic props, artworks, and intelligent household decorations fields. [ABSTRACT FROM AUTHOR]

Purpose: This paper aims to identify the most common fungal species that grow on paper manuscripts and cause bio-deterioration. It also detects the impact of additive materials on fungal degrading and builds a wide database. Thus, it helps conservators understand this phenomenon. Design/methodology/approach: In total, 15 samples were collected from different paper manuscripts suffering from fungi. The achievement of the study objectives depends on using a variety of analyzes, such as a microbiological study, which indicated that three main fungi grew on the paper samples. Then, a digital microscope and an environmental scanning electron microscope were used to detect the effect of fungi on paper fibers. Fourier transform infrared microscopy was used to identify the binding medium and the X-ray diffraction method was used to measure the crystallinity index of cellulose of the paper samples. Findings: Arabic gum was used as a binder medium with the samples. Aspergillus Niger, Aspergillus Fumigatus and Aspergillus Clavatus were the most common fungal species that grew on the Qur'an papers under investigation. They also caused much common damage to the paper samples. The results of the analyzes also showed that the highest crystallinity index of cellulose was in the samples that contained the lowest rate of fungal growth. Originality/value: This paper highlights the relationship between fungal degradation and the multi-component nature of paper manuscripts. It builds a wide database that correlates the composition and the degradation of the Qur'an papers. [ABSTRACT FROM AUTHOR]

This paper aims at re-evaluating two of Hungarian artist Dóra Mauer's films, the video work PROPORTIONS (1979) and the 16mm film TIMING (1973/80). Both films follow a rigid structure. In PROPORTIONS, Maurer uses a paper roll to compare her own body measures repeatedly; in TIMING, she repeatedly folds a white linen to compare the rhythm of her arm movements. Through her use of paper and the gesture of folding, the two films can be read as references to the very origin of the term format , as coined in early letterpress printing. When the notion of format is understood as a determination of a ratio and, as such, as an indexical reference to given social relationships (Summers, 2003), these films unfold sociocultural and political meanings. The present paper traces this spectrum of meaning through the pointed inclusion of historical discourses surrounding early motion studies, the art scene in socialist Hungary in the 1970s, and early time experiments before the advent of precision clocks. [ABSTRACT FROM AUTHOR]

Electrocoagulation and chemical coagulation are treatment methods based on the same removal mechanism.In this study, it was investigated the effectiveness of coagulation methods using Al electrodes and Al2(SO4)3.18H2O on the wastewaters from cardboard production.In the electrocoagulation experiments, the optimum current and pH where the highest COD removal efficiency by 54% was achieved were determined respectively as 10A and 6.62.The study also it was seen that 58%COD removal was reached for the KCl concentration of 0.5 mg/L that was applied.In the chemical coagulation study, the highest removal efficiencies were obtained as 36%, 95% and 97% for respectively COD, color and turbidity.The results show that higher efficiency could be achieved by electrocoagulation as a pre-treatment step. [ABSTRACT FROM AUTHOR]

A novel macro-RAFT emulsifier was synthesized with S, S'-bis(α, α'-dimethyl-α"-acetic acid)-trithiocarbonate (BDATT), M13-10 (self-made emulsifier) and acrylate monomer, which was further used to prepare surface sizing agent. On the other hand, M13-10 was synthesized with iso-tridecanol polyoxyethylene ether, sodium methoxide and sulfamic acid as the starting materials. The hydrophilicity of macro-RAFT emulsifier and the performance of surface sizing agent were affected by BDATT used as the chain transfer agent and M13-10 as the hydrophilic monomer. So, the CMC and HLB of the emulsifier prepared with different M13-10 content and BDATT content, were compared, as well as the particle size of the prepared surface sizing agent, and the cobb, bursting resistance, tensile resistance, folding endurance and roughness of paper sized. The results reveal that surface sizing agent with macro-RAFT emulsifier of which the amount of M13-10 is 7 w% and the amount of BDATT is 2.5 w% demonstrates the best sizing effect on paper with the contact angle of 119°, the surface water absorption (cobb) of 48.8 g/m2, the bursting strength of 285 kPa, the folding endurance of 19 and the tensile strength of 59.6 kN/m. [ABSTRACT FROM AUTHOR]

This work has been conducted to investigate the effect of accelerated ageing on the filler-free (control) handsheets and the ones having Precipitated Calcium Carbonate (PCC) and Zeolite (Clinoptilolite) fillers. The diagnosis approach of this work has been based on the use of the techniques of attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR) and X-ray diffraction (XRD). The FT-IR technique has allowed identifying the changes in cellulose components of handsheets. Likewise, the XRD technique has provided to diagnose the changes in crystallinity of the handsheets and fillers. The results found out that PCC and Zeolite fillers could be easily added to the structure of the paper network by changing various experimental variables. The loss of C−O functional groups and the formation of carbonyl groups in handsheets has been analysed by accelerated ageing. The spectroscopy results confirmed that usage of zeolite filler has a retarding and structurally improving effect on the glycosidic linkages. Recent findings have been provided new insights into the role of the synergistic effect of the combination of PCC and zeolite fillers in the decelerating of certain ageing mechanism. [ABSTRACT FROM AUTHOR]

The chloropropanols, monochloropropane-1,2-diol (3-MCPD) and 1,3-dichloro-2-propanol (1,3-DCP) are potential contaminants that may be found in food contact materials (FCM) from paper and paperboard that have been treated with certain wet-strength resins. They can migrate from the paper matrix to aqueous food and beverages and, due to their potentially carcinogenic properties, are of increasing interest in quality assurance or official controls of paper-based FCM. We hereby describe an improved method for the analysis of 3-MCPD and 1,3-DCP in water extracts of FCM making use of 1-chloro-3-methoxy-2-propanol (CMP) as a novel internal standard. The LOD and LOQ were determined to be 0.4 µg/L and 1.2 µg/L for both analytes, making the method appropriate for the quantification of 3-MCPD and 1,3-DCP below the current legal limits. The method was applied to an extensive market survey of food contact articles made from paper and paperboard including 674 samples. The survey revealed that a high percentage of the products available on the market (e.g., up to 55% of the analysed drinking straws) exceed the BfR limits with values of up to 327 µg/L 3-MCPD and 20 µg/L 1,3-DCP detected in the cold water extract. Remarkable differences were observed concerning the release of 3-MCPD and 1,3-DCP from different kinds of paper-based FCM products, with drinking straws, cupcake cases, bagasse bowls and kitchen rolls showing particularly high rates (>10%) of non-conformity with the legal limits. A number of samples with especially high concentrations were additionally analysed by hot water extraction, which surprisingly yielded considerably lower results for the release of 3-MCPD and 1,3-DCP than cold water extraction. The results indicate that cold water extraction is the most sensitive method to detect the migration and control the risk of exposure to 3-MCPD and 1,3-DCP. [ABSTRACT FROM AUTHOR]

From the moment of production, paper as a printing substrate is exposed to the process of natural ageing regardless of the type of cellulose fibres in its composition. Accordingly, the prints produced by the various printing techniques are also exposed to several factors that impair the quality of the print i.e. its colour over time. Therefore, it is very important to properly select the printing substrate for achieving a high quality of graphic products. For that purpose, three types of papers with hemp fibres were used as printing substrates which were printed with laboratory hand-operated instrument Esiproof using flexographic cyan (C), magenta (M), yellow (Y) and black (K) water-based inks. Prints were artificially aged in SunTEST XLS+ test chamber according to standard ASTM D 6789-02 for 48 and 96 hours. Based on changes in the reflectance spectra of each printed ink after exposure to electromagnetic radiation it was noticed how composition of printing substrate strongly influence on colour stability of prints due time. An increase of exposure time to electromagnetic radiation leads to a decrease in the value of the reflectance of the printing substrate and cyan, magenta and yellow prints. It was confirmed how electromagnetic radiation have the greatest impact on the reflectance of yellow print, while the black one is the most stabile regardless of the substrate it was printed on. [ABSTRACT FROM AUTHOR]

In this study, the effects of the lacquer applied to the printing materials which were printed by electrophotographic printing method on printing quality were investigated. In practice, printing materials with the same weight and different optical properties were used and the study was carried out in three stages. The optical and physical properties of the printing materials used in the first part were determined, in the second part, the printing of these materials by electrophotographic printing method and printability tests were performed. In the third chapter, matte and glossy lacquers were applied to these printed materials and printability tests were repeated. As a result of the study, it was observed that the application of gloss and matte lacquer caused a decrease in the printing density values and also the application of matte lacquer caused a decrease in the gloss values. [ABSTRACT FROM AUTHOR]

The charging/discharging delays in superconducting coils wound without insulation (NI coils) are a major drawback of the technique. While removing the insulation improves safety margins, the increase in the characteristic time constant τc can make a coil unfit for a particular purpose. It is widely accepted for instance that NI coils will not be used in ac applications where τc ~ 1/f. To decrease τc of the NI coils, the same length of superconductor can be wound/connected in parallel rather than in series — decreasing the inductance L, and hence the time constant τc, while maintaining the number of amp-turns IopN. Here we investigate the effect of parallel connecting coils in a magnet using a 2D axially symmetric model which captures all the necessary electromagnetic properties of the HTS NI coils. These properties include: critical current anisotropy Jc(B,θ), turn-to-turn conductivity, as well as winding parallelism. Our modeling results show that the parallel connected magnet experiences magnet-wide shielding current effects. Whilst these shielding currents affect field homogeneity — the model enables this effect to be quantified. Furthermore, shielding currents are not an issue when running NI coils in saturated mode. The modeling work presented here provides a simple initial example of how magnet designers may approach designing, optimizing, and operating high current, HTS NI coils. [ABSTRACT FROM AUTHOR]

We report a paper-based chemosensor array device (PCSAD) for the quantitative detection of oxyanions including the herbicide glyphosate (GlyP) in aqueous media. The mechanism of the oxyanion detection relies on a coordination-binding-based sensor array. In this study, the competitive coordination binding among Zn2+, four catechol dyes, and seven oxyanions caused noticeable colour changes. The colour changes were employed for qualitative and quantitative analyses using an in-house automated image-processing algorithm with pattern recognition for digital images. A linear discrimination analysis discerned similarly structured oxyanions with 100% accuracy. The regression analysis allowed the accurate quantification of GlyP in the herbicide products with a limit of detection of 16 mg/L, which is lower than the health advisory value for children (20 mg/L) stipulated by the environmental protection agency (EPA). PCSAD is a powerful sensor device for the on-site quantification of aqueous anions for environmental assessment. [ABSTRACT FROM AUTHOR]

Two kinds of cellulose/ZnO piezoelectric papers are prepared by crushing and dissolving methods. The papers are characterized by SEM and analyzed by a piezoelectric equipment. The differences in the structure and piezoelectric performance of the two kinds of papers are explored. The effects of ZnO add-on amount, thickness of the papers, and pressure on the piezoelectric properties are discussed and compared with a PVDF film. The mutts show that the fibers of the piezoelectric paper prepared by the dissolving method are smooth and tightly bounded to ZnO, which makes ZnO uniformly coat on the surface of the fibers. The higher the pressure, the higher the piezoelectric properties. The thicker the piezoelectric paper, the higher the piezoelectric properties. The piezoelectric paper with 20% ZnO added by the dissolving method has high piezoelectric properties, and the maximum output current is 52.36 nA/cm². The piezoelectric properties of the piezoelectric paper are comparable to the purchased PVDF film. [ABSTRACT FROM AUTHOR]

The grey silverfish Ctenolepisma longicaudatum is a new and serious pest spreading rapidly across Europe. Compared to the silverfish Lepisma saccharinum, it does not depend on relative humidity above 70% and thrives also in new museum buildings, modern storage depositories, apartments, and office buildings. Especially collections of graphic art, modern art on paper, photographs, but also archives and libraries are increasingly affected by this pest. Damage of paper objects has been reported by different authors and institutions across Europe. As these animals live in inaccessible cracks and crevices inside the buildings, we investigated the spread of microorganisms on living grey silverfish, to show a potential additional threat posed by this pest. In 8 locations in Austria living animals were collected with traps and placed for 10 min on agar plates which were incubated for 2 weeks. After incubation of 50 agar plates, between 2 and 20 colonies of fungi were growing on each plate. The most dominant fungal genera were Cladosporium (Cladosporium cladosporioides clade) and Penicillium (Penicillium glabrum, Penicillium decumbens); also, species of the genera Aspergillus, Alternaria, Botrytis, Bartalinia, Byssochlamis, Chaetomium and Mycothypha were found. The diversity of fungi reflects the common fungal community of museums and archives. The spores and mycelial fragments of the fungi are obviously travelling on the legs and bodies of the silverfish. [ABSTRACT FROM AUTHOR]

Landfills are engineered, heterogeneously contaminated sites containing large reservoirs of paper waste. Cellulose degradation is an important process within landfill microbial ecology, and these anoxic, saturated environments are prime locations for discovery of cellulases that may offer improvements on industrial cellulose degradation efforts. We sampled leachate from three locations within a municipal landfill, a leachate collection cistern, and groundwater from an adjacent aquifer to identify cellulolytic populations and their associated cellulases. Metagenomic sequencing identified wide-spread and taxonomically diverse cellulolytic potential, with a notable scarcity of predicted exocellulases. 16S rRNA amplicon sequencing detected nine landfill microorganisms enriched in a customized leachate medium amended with microcrystalline cellulose or common paper stocks. Paper-enrichment cultures showed competition dynamics in response to the specific composition (lignin: hemi-cellulose: cellulose) of the different paper stocks. From leachate biomass, four novel cellulolytic bacteria were isolated, including two with the capacity for cellulolysis at industrially relevant temperatures. None of the isolates demonstrated exocellulase activity, consistent with the metagenome-based predictions. However, there was very little overlap between metagenome-derived predicted cellulolytic organisms, organisms enriched on paper sources, or the isolates, suggesting the landfill cellulolytic community is at low abundance but able to rapidly respond to introduced substrates. [ABSTRACT FROM AUTHOR]

A small box, hitherto described as white lacquerware, currently displayed at the Chinese Pavilion, Drottningholm, Sweden, is an unusual example of artefacts imported from the Far East during the era of the East India Companies. By using microscopy for cross- and thin sections, X−ray fluorescence microscopy, attenuated total reflection Fourier transform infrared spectroscopy, and pyrolysis-gas chromatography-mass spectrometry, some of the specific characteristics of the box are described, and it was possible to differentiate original from more recent restoration material. Among other findings, the results suggest that white glue tempera is a better description, based on indications of calcium carbonate and protein, and support an earlier attribution of the box to an Edo period doll maker in Kyoto. [ABSTRACT FROM AUTHOR]

Paper evidence usually undergoes two consecutive examinations in forensic laboratories: ESDA (electrostatic detection apparatus) to detect indented impressions and a subsequent search for fingermarks by optical, physical, and chemical techniques. The ability of ESDA in visualizing fingermarks is well known. The aim of the present study is to understand better how long fingermarks can be developed with ESDA and if the different constituents of fingermarks show a different susceptibility to being developed. Several types of marks were collected from six donors on A4 standard office copy paper and tested with ESDA up to 69 days from deposition. A clear difference between natural, eccrine, and sebaceous marks emerged, being the latter ones better developed. ESDA developed standard sebaceous marks up to 16 days from deposition, whereas natural marks were visible within a few days. Eccrine marks were mainly visualized in reverse mode, despite the quality of these marks was not as good as the sebaceous marks. The appearance of the mark (standard/reverse) seemed to be correlated with time since deposition. Data suggest that the mechanism by which ESDA visualizes the fingermarks could be related to the residue (water‐soluble and/or non‐water‐soluble) available on the surface of the substrate and not yet absorbed by the paper. ESDA could act as a useful screening tool in fingermark visualization on porous surfaces, especially because it is a non‐destructive technique. Therefore, as a general procedure, it is highly recommended to acquire potential fingermarks developed by means of ESDA before proceeding with fingermark visualization. [ABSTRACT FROM AUTHOR]

The paper is an integral part of our cultural development. Its’ properties are determined by the properties of the fibrous materials of which it is composed by and from the technological regime in its production. The good knowledge of the fibrous materials used, their chemical composition, morphological and anatomical structure in the restoration practice is essential for proper conduction of the recovery procedures. In world restoration practice, Japanese paper is the most often used material for the renovation of paper documents. The examination and microscopic analysis of Japanese paper contributes to its proper use in restoration practice. [ABSTRACT FROM AUTHOR]

A paper-based membrane coated by graphitic carbon nitride (g-C3N4) is prepared via a dip-coating method and used as a separator for sodium metal batteries with merits of low cost and environment-friendliness. Introduction of g-C3N4 effectively improves the ionic conductivity and the structural stability of the separator. Compared with traditional polyethylene separators and Al2O3-coated separators, the g-C3N4-coated separators show better electrolyte wettability, thermal stability, and electrochemical stability. Therefore, Na||Na3V2(PO4)3 battery using the g-C3N4-coated separator exhibits better cycling stability and higher rate capability. These results prove that the g-C3N4-coated paper-based separator is expected to become the next generation of low-cost and high-safety separator in sodium metal batteries. [ABSTRACT FROM AUTHOR]

The entire world seems to have responded to COVID-19 pandemic in a knee-jerk manner with a short mindset without building on the existing strengths of public health infrastructure. National governments cannot be blamed for this as we are dealing with a crisis that comes once in a lifetime. Realising this, the Organized Medicine Academic Guild (OMAG) an association of major health associations in this country has suggested measures for long-term solutions to COVID-19-like pandemics in the form of a policy paper by OMAG. [ABSTRACT FROM AUTHOR]

Background: Through a close reading of the four issues of The Bowater Papers, this article aims to understand the rise of a paper modernity and to reinsert it--as material and infrastructure-- into media studies. Analysis: Producing wood paper is a strain on the landscape and the environment. The Bowater Papers showcases the histories and material possibilities of paper media products. A paper-dependent modernity can be understood as an infrastructural assemblage of harvesting, production, circulation, and consumption. Conclusion and implications: Paper calls for a natural history and geography of media. Thinking about the mediations from tree to paper through the encompassing notion of "xylomedia" is a way of articulating the intersection of the material, environmental, and infrastructural in media studies. Today is still a paper world, one that is also the age of lignin, package, and Amazon. [ABSTRACT FROM AUTHOR]

Summary: Solar steam generation has proven to be a sustainable method to handle water shortage. Various materials for solar steam generation have been introduced in the past few years. However, the utilization of tedious and complicated synthesis to generate a photoactive layer is a matter of concern in the fabrication solar steam generation devices. Thus, improved methods toward cost‐effectiveness by exploring economical materials with simple manufacturing process are urgently and essentially needed. In this study, we first report on manufacturing hybrid membranes using commercially accessible materials, that is, cellulose paper and pencil graphite. The proposed method is to trace and coat a cellulose paper directly with a pencil without the use of solvents and chemicals, and it is possible to create an ecofriendly photoactive layer without a complicated process. The formed pencil graphite‐traced membranes were successfully utilized in solar steam generation and showed excellent steam generation rate of 4.32 kg/m2h which is almost 3.5 times more than that of pristine membrane at solar intensity of 3 Sun. The developed method could be widely utilized in the field of solar steam generation, since it is very facile and simple, and can be integrated to other commonly used materials for solar steam generation such as fabric and wood. In addition, on‐site production is possible, so it has a potential to be utilized in remote and resource‐limited areas for steam generation. [ABSTRACT FROM AUTHOR]

Cellulose nanofibers isolated from unbleached pulp are characterized by different surface properties due to presence of lignin at their surface, in addition to lower cost than isolated from bleached pulp. In the current work, the effect of cellulose nanofibers isolated from unbleached neutral sulfite and bleached soda rice straw pulps (so called UBCNF and BCNF) on improving paper sheet properties of unbleached and bleached rice straw pulp (so called UBP and BP) was studied. The effect on mechanical properties (tensile strength, burst strength, and tearing resistance) and physical properties (porosity and water vapor permeability) was studied. Scanning electron microscopy (SEM) was used to assist in explaining the obtained results. The result showed that using BCNF and BP resulted in better improvement in mechanical properties and also more effective in reducing porosity of paper sheets than in case of using UBCNF and UBP. These results indicated stronger bonding between nanofibers and pulps' fibers in case of using BCNF and BP (surfaces rich in cellulose hydroxyl groups) than in case of UBCNF and UBP (surfaces rich in lignin). Water vapor permeability of paper sheets made from unbleached or bleached pulps did not significantly affect by the addition the nanofibers. [ABSTRACT FROM AUTHOR]

The dimensional stability of paper products is a well-known problem, affecting multiple engineering applications. The macroscopic response of paper to moisture variations is governed by complex mechanisms originating in the material at all length-scales down to the fiber-level. Therefore, a recently-developed method, based on Global Digital Height Correlation of surface topographies is here exploited to measure the full-field hygro-expansion of single fibers, i. e. a surface strain tensor map over the full field of view is obtained as function of time. From the strain field, the longitudinal and transverse hygro-expansion and principle strains can be calculated. Long- and intermediate-duration dynamic tests are conducted on softwood and hardwood fibers. A large spread in the softwood fiber's transverse and longitudinal hygro-expansion coefficient ratio was found, while hardwood fibers behave more consistently. Computing the principle strain ratios reduces this spread, as it takes into account the variations of the deformation direction, which is directly affected by the micro-fibril angle (MFA). Furthermore, long-duration tests allow identification of the half-times at which the fibers equilibrate. Finally, the determined major strain angles for all fibers are consistent with the MFA ranges reported in the literature. [ABSTRACT FROM AUTHOR]

Paper has been the most significant carrier of written information for many centuries. To prolong the life expectancy of papers, the polyurethane based on nanosilica was used to strengthen the paper fibers in this work. The relation between the mass concentration of polyurethane based on nanosilica and the specific properties of papers (e. g., folding endurance, tensile strength, tearing strength, whiteness and glossiness) were investigated. In addition, the effect of polyurethane based on nanosilica on the acid/alkali resistance and ageing resistance were studied. The results showed that polyurethane based on nanosilica could significantly improve the mechanical properties and ageing resistance of papers. [ABSTRACT FROM AUTHOR]

Phthalates are one of many chemical compounds that are used as plasticisers. Packaging can transfer plasticisers to the surfaces of foods or other materials. A recent study suggested a link between fast food consumption and increased urine phthalate metabolites even though phthalates are most commonly found in food contact materials made of PVC while fast food packaging is most commonly composed of paper and paper board. Phthalates in PVC are usually present in percent concentrations. In non-PVC food contact materials, such as paper or paperboard, the concentrations, if any, are expected to be significantly lower which can greatly impact the analytical method used for their determination. Due to the widespread use of plasticised PVC in many commercial applications, background concentrations of phthalates are a concern for trace concentration analyses and background contamination must be avoided when performing these analyses. A glassware cleaning method was developed and a solvent extraction with dichloromethane and hexane was used to extract phthalates from paper-based food packaging. The extracts were then analysed using a GC-MS/MS. The minimum reporting concentrations for the method were determined to be 0.10–0.40 µg/g depending on the phthalate investigated. Phthalate concentrations in several different non-PVC printed and unprinted packaging are presented. Of the 54 packaging samples tested, 10 samples contained no reportable concentrations of any of the 6 phthalates investigated. Of those that were reportable, all measured lower than 10 µg/g and in fact, most had concentrations less than 1 µg/g. These data demonstrate that phthalates from fast food packaging do not significantly contribute to overall consumer exposure. [ABSTRACT FROM AUTHOR]

In this work, barium sulfate (BS) fibers with a three‐level nanorod‐assembled hierarchical structure have been synthesized in a large scale by the barium oleate precursor hydrothermal method. A new kind of anti‐acid and anti‐alkali fire‐resistant BS inorganic paper has been developed using BS fibers, glass fibers and inorganic adhesive, and it has advantages such as high flexibility, good tensile strength, excellent fire‐resistant properties, excellent corrosion resistance to strong acids and strong alkalis. It is expected that the anti‐acid anti‐alkali fire‐resistant BS paper has promising applications under various high‐temperature and harsh conditions. [ABSTRACT FROM AUTHOR]

This research study proposes a classification system to identify and prevent occupational accidents in fiber storage warehouses at a pulp and paper facility. The present analysis is based on variables including pedestrian circulation, bobcat, trailer trucks, access, pedestrian circulation zones, and handrails. The proposed methodology defines and trains the system by using occupational accident event data collected at the facility. Three different predicting algorithms are used: J48 decision-making trees, Naive Bayes, and Bayesian nets. The results show that the J48 decision-making tree algorithm accurately identifies possible occupational accidents 90% of the time. It is concluded that identifying variables involved in occupational accidents allows generating a C4.5 (J48) decision-making tree that can be used as a support tool to prevent occupational accidents. [ABSTRACT FROM AUTHOR]

While hundreds of scientific and artistic studies have been undertaken about Yunus Emre, one of the most important figures of Turkish culture and literature, only a few bibliographic studies have been chosen to compile these studies. Moreover, some of the studies are quite narrow in scope. There has been a rapid increase in the literature about Yunus Emre since the first comprehensive bibliographic study covering the period up to 1991. However, it remains a major shortcoming in the field that a comprehensive bibliography study has not been conducted. In this paper, which was written on the occasion of Yunus Emre Year, the author aimed to make a bibliographical master-text of the literature about Yunus Emre from 1991 to 2021. The bibliographic tags of the books, theses, articles, symposiums, and papers published between these years are given. [ABSTRACT FROM AUTHOR]

Background: Inpatient nursing documentation facilitates multi‐disciplinary team care and tracking of patient progress. In both high‐ and low‐ and middle‐income settings, it is largely paper‐based and may be used as a template for electronic medical records. However, there is limited evidence on how they have been developed. Objective: To synthesise evidence on how paper‐based nursing records have been developed and implemented in inpatient settings to support documentation of nursing care. Design: A scoping review guided by the Arksey and O'Malley framework and reported using PRISMA‐ScR guidelines. Eligibility criteria: We included studies that described the process of designing paper‐based inpatient records and excluded those focussing on electronic records. Included studies were published in English up to October 2019. Sources of evidence: PubMed, CINAHL, Web of Science and Cochrane supplemented by free‐text searches on Google Scholar and snowballing the reference sections of included papers. Results: 12 studies met the eligibility criteria. We extracted data on study characteristics, the development process and outcomes related to documentation of inpatient care. Studies reviewed followed a process of problem identification, literature review, chart (re)design, piloting, implementation and evaluation but varied in their execution of each step. All studies except one reported a positive change in inpatient documentation or the adoption of charts amid various challenges. Conclusions: The approaches used seemed to work for each of the studies but could be strengthened by following a systematic process. Human‐centred Design provides a clear process that prioritises the healthcare professional's needs and their context to deliver a usable product. Problems with the chart could be addressed during the design phase rather than during implementation, thereby promoting chart ownership and uptake since users are involved throughout the design. This will translate to better documentation of inpatient care thus facilitating better patient tracking, improved team communication and better patient outcomes. Relevance to clinical practice: Paper‐based charts should be designed in a systematic and clear process that considers patient's and healthcare professional's needs contributing to improved uptake of charts and therefore better documentation. [ABSTRACT FROM AUTHOR]

Three natural extracted oils from Citrus reticulata peels, C. aurantifolia leaves, and Linum usitatissimum (linseeds) were used as antifungal agents against the growth of Aspergillus flavus and Penicillium chrysogenum. The following main compounds (determined via gas chromatography--mass spectrometry) were found. The essential oil (EO) from C. aurantiifolia leaves contained limonene (22.96%), geranyl acetal (13.53%), and geraniol acetate (13.33%); the n-hexane oil from C. reticulata peels contained methyl-13-cyclopentyltridecanoate (16.74%), and D-limonene (16.06%); and linseed oil contained linoleic acid (27.36%), and oleic acid (19.01%). The inhibition of fungal growth significantly was reached 100% against A. flavus at all tested C. aurantifolia leaf EO concentrations and at a concentration of 2000 µL/mL for linseeds oil. The growth inhibition reached 100% against P. chrysogenum with C. aurantifolia leaf EO concentrations of 125-2000 µL/mL. Citrus reticulata peel EO had 100% growth inhibition of P. chrysogenum at concentrations of 2000 µL/mL and 1000 µL/mL, while linseeds oil had 100% growth inhibition at 2000 µL/mL. Thermogravimetric analysis showed that C. aurantifolia EO yielded the greatest thermal stability and color change protection to cotton pulp, while linseed oil was found to protect wood pulpbased and historical papers. [ABSTRACT FROM AUTHOR]

The article briefly outlines the history of the handmade paper production, from its invention in China in 105 CE, its expansion through the Arab world and its arrival in Europe, to the end of the 18th century when paper began to be manufactured by machines. The history of the handmade paper is a long and interesting one, since its first invention as a replacement for parchment which was a prevalent writing surface material until invention of the first machines for grinding the paper pulp. The paper technology’s voyage through Asian countries via Arab countries to Europe had lasted 11 centuries and had gone through various technological changes. Some of those have been kept until today as part of the paper manufacturing tradition. After paper arrived in Europe the technology and raw material had been adjusted to local circumstances: linen rags began to be used as raw material, with gelatine as an addition. The technologies became more advanced, paper mills expanded and the demand for paper increased as the result of the invention of the printing press and rising book production. The paper also outlines the historical development of watermarks, from the oldest surviving simple ones from Cremona, Italy to the more complex ones that gradually appeared as the result of the technological advancement. Paper watermark collectors and their collecting passion are responsible for the development of the new auxiliary historical science i.e. filigranology. Today entire digital platforms across Europe are dedicated to this part of paper history, registering their appearance that can help in dating the paper and sometimes even documents. [ABSTRACT FROM AUTHOR]

Background: The transition from traditional print medium to a digital medium may affect the accommodative response (AR) because of the differences in the characteristics of the targets viewed. Aim: This study investigated how the accommodation system responded to targets displayed on a tablet computer compared to that on paper. Setting: The study was conducted amongst students at a university in South Africa. Methods: Using a quantitative, cross-sectional study the AR, amplitude of accommodation (AA), and accommodative facility (AF) were assessed with a target on an iPad and a paper-based one on a non-probability sample of 30 university students. Data was analysed using descriptive statistics and Bland Altman plots. Results: The median AR with a tablet was +0.25 dioptre (D) compared to +0.21 D with the paper-based target. This difference was neither statistically nor clinically significant. The median AA with a tablet computer target was 10.59 D and 9.85 D with a paper-based target. While this difference was statistically significant (p = 0.002), Bland Altman analysis revealed comparable measurements with both types of targets. Both Wilcoxon Signed Ranks Test (p = 0.462) and Bland Altman analysis found comparable medians for AF obtained with a target on paper (7.67 cycles per minute [cpm]) and a target on the tablet computer (7.17 cpm) to be comparable. Conclusion: The accuracy, strength and flexibility of accommodation were comparable for tablet computer and paper-based targets. [ABSTRACT FROM AUTHOR]