Search

A nonlinear dynamic model with full flight envelope controller is developed for the propulsion system of a partially turboelectric single-aisle aircraft. The propulsion system model consists of two turbofan engines with a large percentage of power extraction, feeding an electric tail fan for boundary layer ingestion. The dynamic model is compared against an existing steady state design model. An electrical system model using a simple power flow approach is integrated into existing modeling tools used for dynamic simulation of the turbomachinery of the vehicle. In addition to the simple power flow model of the electrical system, a more detailed model is used for comparison at a key vehicle transient flight condition. The controller is a gain scheduled proportional-integral type that is examined throughout the flight envelope for performance metrics such as rise time and operability margins. Potential improvements in efficiency for the vehicle are explored by adjusting the power split between the energy used for thrust by the turbofans and that extracted to supply power to the tail fan. Finally, an operability study of the vehicle is conducted using a 900 nautical mile mission profile for a nominal vehicle configuration, a deteriorated propulsion system at the end of its operating life, and an optimized power schedule with improved efficiency.

In the past few years, NASA (National Aeronautics and Space Administration) Aeronautics Research Mission Directorate (ARMD) has introduced and updated a “New Blueprint for Transforming Global Aviation†. This blueprint consists of six NASA Aeronautics Research Strategic Thrusts â€" “The updated vision is designed to ensure that through NASA's aeronautical research the United States will maintain its leadership in the sky and sustain aviation so that it remains a key economic driver and cultural touchstone for the nation.†In mid-2016, technology development roadmaps were developed by ARMD for each of the strategic research thrusts and these roadmaps are continually being updated based on feedback from the broader aeronautics research community. The NASA Aeronautics research vision is implemented through a set of 4 programs â€" Advanced Air Vehicles Program (AAVP), Airspace Operations and Safety Program (AOSP), Integrated Aviation Systems Program (IASP), and Transformative Aeronautics Concepts Program (TACP). The Intelligent Control and Autonomy Branch (ICAB) at NASA Glenn Research Center (GRC) in Cleveland, Ohio, is leading and participating in various projects in partnership with other organizations within GRC and across NASA, the U.S. aerospace industry, and academia to develop advanced controls and health management technologies for aero-propulsion systems that will help meet the goals of the ARMD programs. These efforts are primarily under the various projects under AAVP, AOSP, and TACP. The ICAB current research tasks in support of ARMD program are described in this paper. The paper provides motivation, background, technical approach and recent accomplishments for these tasks, as well as a couple of tasks completed in the previous fiscal year.

The reliability of the propulsion system of an aircraft is paramount for the aircraft safety and hence the aircraft health must be monitored continuously. In contrast to fuel- operated aircraft, electric battery-operated propulsion system poses specific problems, such as, the remaining battery power does not linearly decrease and cannot be measured directly. In this paper, we describe a combined monitoring and prognostics architecture that can continuously monitor all components of the electric propulsion system with respect to safety and performance properties as well as state of charge and rest of useful life for the battery. Our system combines a detailed electrochemical battery model for Li-ion batteries with a powerful prognostics engine based upon an Unscented Kalman Filter with the R2U2 monitoring device, which provides efficient observers for metric temporal logic and Bayesian reasoning. R2U2 is a real-time, realizable, responsive, unobtrusive unit, which continuously monitors sensor readings, outputs of the prognostics engine, as well as the ight software status for safety, performance, and security properties. We illustrate our architecture with two case studies, one reporting actual ight tests with an X8+ octocopter and the other a software-in-the-loop simulation with an unmanned Edge 540 electric aircraft model.

The aeronautics industry has been challenged to increase efficiency, reduce noise and emissions, and decrease dependency on carbon-based fuels. To address these needs, NASA has identified and begun to pursue electrified aircraft as a possible solution. The power system for an electric aircraft can exist in many different forms, however; at the early design stage the engineer(s) must identify whether a hybrid- or turbo- electric solution may be best, whether the power transmission system is to be AC or DC, and to ultimately answer the question: does the electric solution provide a net system benefit compared to the fully mechanical solution? This paper describes a generalized power system architecture sizing and analysis framework to provide a mechanism to answering these questions, along with an example based on the STARC-ABL Architecture.

Over the past few decades, there has been significant research into propulsion concepts attempting to employ pressure gain combustion. Pressure gain combustion concepts to date have resulted in dynamic, non-uniform gas flows which are difficult to characterize and compare with more conventional forms of propulsion. This paper proposes a technique to derive for the pressure gain combustion device an equivalent, steady, uniform gas pressure that is available to do work or provide thrust, thereby providing a direct comparison with conventional propulsive devices.

The Commercial Aero-Propulsion Control Working Group (CAPCWG), consisting of propulsion control technology leads from The Boeing Company, GE Aviation, Honeywell, Pratt & Whitney, Rolls-Royce, and NASA (National Aeronautics and Space Administration) Glenn Research Center, has been working together over the past year to identify propulsion control technology areas of common interest that we believe are critical to achieving the challenging NASA Aeronautics Research goals for Thrust 3a: Ultra-Efficient Commercial Vehicles - Subsonic Transports, and Thrust 4: Transition to Alternative Propulsion and Energy. This paper describes the various propulsion control technology development areas identified by CAPCWG as most critical for NASA to invest in. For Thrust 3a these are: i) Integrated On-Board Model Based Engine Control and Health Management; ii) Flexible and Modular Networked Control Hardware and Software Architecture; iii) Intelligent Air/Fuel Control for Low Emissions Combustion; and iv) Active Clearance Control. For Thrust 4a, the focus is on Hybrid Electric Propulsion (HEP) for single aisle commercial aircraft. The specific technology development areas include: i) Integrated Power and Propulsion System Dynamic Modeling for Control; ii) Control Architectures for HEP; iii) HEP Control Verification and Validation; and iv) Engine/Airplane Control Integration. For each of the technology areas, the discussion includes: problem to be solved and how it relates to NASA goals, and the challenges to be addressed in reducing risk.

Previous studies of Ejector-Enhanced Resonant Pulse Combustors considered configurations that were relatively long, making them difficult to incorporate in practical gas turbine engines. In the present study, more compact configurations are analyzed, focusing on the system pressure gain. The study shows that it is possible to reduce the length of both the pulse combustor and ejector components without compromising the device's performance. In fact, it is found that in several of the compact configurations analyzed, the system pressure gain actually increased, reaching pressure gain levels above 5%, significantly higher than those obtained in previous studies. The Rayleigh efficiency, which has been used in the past to characterize the performance of pulse combustors, is computed for several of the Ejector-Enhanced Resonant Pulse Combustor configurations. The Rayleigh efficiency is seen to correlate with both average combustor pressure and system pressure gain for a given configuration, however, it could not be used to compare different configurations.

A gas turbine engine includes a gear assembly and a bypass flow passage that includes an inlet and an outlet that define a design pressure ratio between 1.3 and 1.55. A fan is arranged at the inlet. A first turbine is coupled with a first shaft such that rotation of the first turbine will drive the fan, through the first shaft and the gear assembly, at a lower speed than the first shaft. The fan includes a row of fan blades. The row includes 12-16 (N) fan blades, a solidity value (R) that is from 1.0 to 1.3, and a ratio of N/R that is from 10.0 to 16.

This presentation is designed to update and enhance NASA's ability to collect, preserve, disseminate, and communicate to decision makers for Distributed Electric Propulsion technologies. Acronyms: LEAPTech/HEIST (Leading Edge Asynchronous Propeller Technology/Hybrid-Electric Integrated Systems Testbed).

A small scale, high speed turbomachine is described, as well as a process for manufacturing the turbomachine. The turbomachine is manufactured by diffusion bonding stacked sheets of metal foil, each of which has been pre-formed to correspond to a cross section of the turbomachine structure. The turbomachines include rotating elements as well as static structures. Using this process, turbomachines may be manufactured with rotating elements that have outer diameters of less than four inches in size, and/or blading heights of less than 0.1 inches. The rotating elements of the turbomachines are capable of rotating at speeds in excess of 150 feet per second. In addition, cooling features may be added internally to blading to facilitate cooling in high temperature operations.

Because of the growing Urban Air Mobility focus, this presentation provides an attractive alternative to the all-electric X-57 option.

A dual-stream nozzle configuration was studied numerically with the objective of predicting the appearance of tones and study their sources. It was found that some of the tones traced to a coupling between Strouhal shedding from the struts, which held different pieces of the nozzle together, and various duct acoustic modes. A focus of the work was on exploring the nature of the duct modes. First, elements of the numerical procedure were studied for a 4-strut nozzle, validating the results with existing experimental data. The approach was then applied to a 3-strut geometry and four different excitation methods. The predicted tones and associated duct modes are analyzed in detail.

There is increased interest in using electric motors to drive propulsors across a range of small air vehicle classes. Applications include both vertical lift and conventional takeoff and landing systems for Small Unmanned Aircraft Systems. Mission profiles call for integrating these systems into urban airspaces exposing populated areas to new noise sources. In addition to the propulsor noise from rotors and propellers, electric motors are expected to contribute to the overall sound levels and possibly human annoyance. This work presents acoustic measurements of electric motors used for small quadcopters to characterize the sound and identify sources with and without a propeller. Free field microphone measurements were used to determine directivity and a phased microphone array was used to identify sound sources. A companion paper (Part II – Source Characteristics and Prediction) compares the far field results with current probe measurements of the signal driving the motor, the structural response of the motor case, and describes prediction methods of electric motor noise.

The Leading Edge Asynchronous Propeller Technology (LEAPTech) project tested the Hybrid-Electric Integrated Systems Testbed (HEIST) and was intended for a general aviation sized aircraft with Distributed Electric Propulsion (DEP) to show large improvements with regards to efficiency, emissions, safety and operating costs. The wing was designed for high loading to improve ride quality and show improved takeoff and landing characteristics. The full-scale test article wing had a 31-foot-span, had integrated electric motors, was mounted on a truck 20 ft. above ground and driven in a simulated flight test environment at various velocities up to 70 miles per hour. The simulated flight test varied primarily angle of attack and flap settings. These tests were conducted to obtain data and verify blown wing performance primarily with regards to lift. The experimental test results are presented.

Mechanical shaft power and shaft speed of reciprocating internal combustion engines are closely coupled. Maximum rated shaft power is typically produced at or near peak shaft speed. If a general aviation airplane equipped with a reciprocating engine and a variable-pitch propeller attempts a low-noise takeoff by reducing propeller tip speed, propeller power and thrust are reduced. Such takeoffs are not tolerated due to punishing performance effects, such as increased field lengths and poor climb rates. Certain electric motors, however, are able to deliver maximum shaft power over a wide range of shaft speed. Electric or hybrid-electric propeller-driven airplanes should be able to exploit this behavior. At low shaft speeds, high shaft power levels and high blade pitch angles could be combined to recover much of the thrust that would otherwise be lost. This could enable a low-noise operating mode for propellers normally designed for performance rather than for noise. The subject of this paper is an analytical investigation into low-noise takeoffs and steady overflights of a notional general aviation airplane equipped with a propeller driven by an electric motor.

NASA researchers, in a partnership with Boeing, are investigating a fuel-cell powered variant of the X-57 “Maxwell” Mod-II electric propulsion aircraft, which is itself derived from a stock Tecnam P2006T. The “Fostering Ultra-Efficient Low-Emitting Aviation Power” (FUELEAP) project will replace the X-57 power subsystem with a hybrid Solid-Oxide Fuel Cell (SOFC) system to increase the potential range of the electric-propulsion aircraft while dramatically improving efficiency and emissions over stock internal-combustion engines. Our FUELEAP safety analysis faces two primary challenges. First, the Part 23 certificated Tecnam P2006T is undergoing significant modifications to host the hybrid electric-propulsion system, and the challenge is to assure that the safety inherent in the stock aircraft (and subsequently in X-57 Mod-II) is not compromised by changes in avionics, aircraft structural loading, weight and balance, or other considerations. Secondly, because the SOFC power system has little (if any) relevant in-service precedent, our challenge is to assure that we identify and mitigate all reasonably plausible hazards introduced by unique FUELEAP equipage. We are investigating and utilizing Model-Based Safety Analysis (MBSA) methods to help us address these FUELEAP safety challenges. We captured aircraft-level system hazard conditions using instances of a SysML hazard block via aircraft-level Functional Hazard Analysis (FHA). Then, using SysML models of the FUELEAP architecture, we related the hazard conditions to initiating system events and possible mitigations, such as design architecture modifications or operational constraints. We are continuing to define our approach to MBSA by developing a component-by-component inventory of local failure modes and tracing their possible contribution to hazard conditions. Finally, we are applying an argument-based approach to FUELEAP assurance. Through a FUELEAP “safety case,” we are providing an explicit argument for FUELEAP safety by associating assurance evidence with overarching safety claims through a structured argument.

There is increased interest in using electric motors to drive propulsors across a range of small air vehicle classes. Applications include both vertical lift and conventional takeoff and landing systems for Small Unmanned Aircraft Systems. Mission profiles call for integrating these systems into urban airspaces exposing populated areas to new noise sources. In addition to the propulsor noise from rotors and propellers, electric motors are expected to contribute to the overall sound levels and possibly human annoyance. This work presents acoustic measurements of electric motors used for small quadcopters to characterize the sound and identify sources with and without a propeller. Free field microphone measurements were used to determine directivity and a phased microphone array was used to identify sound sources. A companion paper (Part II - Source Characteristics and Prediction) compares the far field results with current probe measurements of the signal driving the motor, the structural response of the motor case, and describes prediction methods of electric motor noise.

NASA is continuing to develop over-the-rotor acoustic liners for turbofan applications. A series of low Technology Readiness Level experiments were conducted to better understand the acoustic and aerodynamic effects of these acoustic liners. The final experiment included the evaluation of four acoustic casing treatment concepts and two baseline configurations in an internal flow axial compressor facility with a 1.5 pressure-ratio high-bypass turbofan rotor. An inlet in-duct array was utilized to extract sound power levels propagating forward from the turbofan rotor. The effect of a circumferentially grooved relative to a hardwall fan case was found to reduce the in-duct sound power level by about 1.5dB for frequencies less than 2kHz while increasing noise from 4 to 8kHz by as much as 7.5dB at low fan speeds. The four acoustic treatment concepts were incorporated into the bottoms of the circumferential grooves and found to provide an additional 1 to 2dB sound power level reduction under 2kHz. The sound power level reduction was found to be even greater, 2.5 to 3.5dB, when evaluating the reduction on rotor alone duct modes (co-rotating modes). The acoustic treatments also appeared to reduce multiple pure tone noise at transonic fan speeds. Depending on the acoustic treatment concept, the high-frequency noise created by the circumferential grooves was reduced by 1.5 to 5 dB. The total noise reduction from acoustic treatments embedded into the bottoms of circumferential grooves relative to a hardwall baseline was found to be 2.5 to 3.5dB sound power level. The sound power level reduction for rotor alone (co-rotating) modes was found to be 3.5 to 4.5dB. These results show the potential for significant turbofan noise reduction by incorporating acoustic treatments over-the-rotor.

The problem of propagation of sound across the shear layer in a turbofan jet exhaust with an external center-body is discussed. The wave equation of interest is compressible Rayleigh equation. Two forms of the equation are considered, and the Green's function solutions subject to appropriate surface conditions on the center-body and flight condition in the ambient are presented. Directivity studied in a heated exhaust at temperature ratio of 2.0 and Mach number 0.90 indicate that a rigid center-body tends to increase the sound propagation at forward angles relative to an exhaust without a center-body, while application of suitable surface liner may significantly reduce this enhancement. A general form of the far-field solution to the propagation equation in a parallel flow under supersonic conditions and in the neighborhood of the shear layer singularity is also discussed.

Lightweight, efficient power production has been a pacing technology for aviation. Advances in airborne electric propulsion technology have enabled new aviation concepts in markets that previously were not dominated by aviation systems, largely because electric propulsion allows for efficient, integrated propulsion/aerodynamic/control solutions that were previously not practical with combustion-based power architectures. These new markets include automated package delivery, urban air mobility, and short-haul transportation. As these markets evolve, the impact of using electricity for airborne propulsion on an expanding mission set, as well as the sheer amount of energy consumed, will begin to challenge the energy harvesting and distribution paradigm as it exists today. Left unaddressed, these challenges could stymie the evolution of these new markets and mobility options. This paper identifies some of the potential systemic issues associated with the expanded use of electric propulsion and explores the requirements associated with alternate aviation power architectures. The recommended path includes the development of a new hybrid-electric aviation power architecture that can be used in conjunction with a portfolio of evolving battery-electric and combustion-based systems.

As electric powertrain and propulsion-airframe integration technologies advance, airborne electric propulsion concepts appear to be on the cusp of disrupting or transforming aviation markets. One of the many challenges to this transformation lies within the onboard energy storage and generation technologies. State-of-the-art battery technology is heavy and lacks support infrastructure; purely combustion-based solutions to electrical power generation suffer from increased inefficiency as compared to a traditional combustion powertrain. This paper explores another alternative: a hybrid-electric, solid oxide fuel cell power system. This power system reforms traditional fuels to feed fuel cells that generate electrical power for the aircraft electric powertrain. A representative power system is designed based on the requirements for NASA’s X-57 Mod II electric flight demonstrator platform, and is shown to exceed system feasibility goals of 300 W/kg and 60% efficiency in at least one configuration. The hybrid-electric fuel cell power system is shown to be competitive with the range performance of a combustion-based power architecture and comparable in mission energy cost to a battery-electric power system.

The increased interest in electric motors for propulsion systems has driven interest in quantifying the contribution of electric motor noise to the overall sound levels and possible human annoyance of the propulsion system. This work presents acoustic measurements of electric motors used for small quadcopters to quantify the sound produced by a number of outrunning motors with different types of controllers. Results are presented for loaded and unloaded motors as installed and uninstalled configurations. Motor resonance frequencies were measured and computed. Current probe measurements showed that the supply current from the controllers contained significant harmonic content for the conventional and sinewave controllers. Acoustic results showed motor noise is typically radiated at frequencies near the mode 2 vibration frequency at roughly 5000 Hz. Electric motor noise was evident in the spectra produced by many of the motor-controller combinations for motors loaded with propellers with levels often greater than those for the motor alone due to increase in the stator magnetic flux density with increased current. An installed configuration produced increases in acoustic radiation over that of the uninstalled motor in a frequency range near the mode 1 vibration frequency near 1200 Hz. A companion paper (Part I - Acoustic Measurements), focuses on source identification using a phased array and directivity characteristics for a baseline configuration.

Baseline noise and aerodynamic data have been acquired for the DGEN Aeropropulsion Research Turbofan (DART) test rig. The DART is a fully-mobile engine test rig featuring a DGEN380 geared turbofan producing approximately 500 lbs. of thrust at sea level and a self-contained control room. Baseline noise data were acquired using 5 microphone arrays, varying distance, configuration, and angle to reflect the measurement locations at several other test facilities. Noise data were acquired at one array location on each test day to establish the repeatability of the measurements. The noise data from the different arrays is analyzed to show the limitations of projecting the results to a common radius when the noise sources are distributed and the measurement location is not in the geometric far-field.

Contributions from the combustor to the overall propulsion noise of civilian transport aircraft are starting to become important due to turbofan design trends and advances in mitigation of other noise sources. Future propulsion systems for ultra-efficient commercial air vehicles are projected to be of increasingly higher bypass ratio from larger fans combined with much smaller cores, with ultra-clean burning fuel-flexible combustors. Unless effective noise-reduction strategies are developed, combustor noise is likely to become a prominent contributor to overall airport community noise in the future. The new NASA DGEN Aeropropulsion Research Turbofan (DART) is a cost-efficient testbed for the study of core-noise physics and mitigation. This paper describes the recently completed DART core/combustor-noise baseline test in the NASA GRC Aero-Acoustic Propulsion Laboratory (AAPL). Acoustic data were simultaneously acquired using the AAPL overhead microphone array in the engine aft quadrant farfield, a single midfield microphone, and two semi-infinite-tube unsteady pressure sensors at the core-nozzle exit. Combustor-noise components of measured total-noise signatures were educed using a two-signal source-separation method and are found to occur in the expected frequency range. The acoustic data compare well with results from a limited 2014 feasibility test and will serve as a high-quality baseline for future research using the DART. The research described herein is aligned with the NASA Ultra-Efficient Commercial Transport strategic thrust and is supported by the NASA Advanced Air Vehicle Program, Advanced Air Transport Technology Project, under the Aircraft Noise Reduction Subproject.

The anticipated development of the on-demand-mobility (ODM) market has accelerated the development of electric aircraft. Most proposed electric aircraft have propulsion systems that consist of fans directly driven by electric motors. The lower complexity of these propulsion systems opens the door to more custom propulsion system designs that are tailored to a given aircraft and its mission. This paper represents initial steps in the development of an electric propulsion system design code. A proof of concept version of the code is presented. The proof of concept version of the code is for the design of an axial flux rim driven propulsion system. NASA's all electric aircraft X-57, is used as a case study for this design code. The results of this case study are used to discuss the feasibility and potential benefits of using an axial flux rim driven propulsor on X-57. The final result of the case study shows a potential 4km increase in range over the current design.

A propulsion system for an aircraft includes first and second turbine engines mounted within a fuselage of the aircraft. The first turbine engine includes a first engine core that drives a first propulsor disposed about a first propulsor axis. The second turbine engine includes a second engine core and a second propulsor disposed about a second propulsor axis parallel to the first propulsor axis. The first engine core and the second engine core are mounted at an angle relative to corresponding ones of the first and second propulsor axes.

This paper investigates the effects of cavity diameter on the acoustic performance of conventional perforate-over-honeycomb liners. This investigation is a follow up to a previous study where it was demonstrated that the cavity diameter has a relatively small effect on the acoustic impedance for core cavity diameters up to 2.0 inches. In the current study, liner concepts are exposed to a complex acoustic environment, where higher-order modes are present. Four liner configurations are explored in this investigation, which include two cavity cores of different cavity diameters combined with two facesheets. These configurations are tested in the Grazing Flow Impedance Tube (GFIT) at Mach 0.0, 0.3, and 0.5 at a source sound pressure level of 150 dB. A comparison of the acoustic performance of these samples suggests that the cavity diameter has a relatively small effect on the acoustic impedance for core cavity diameters up to 2.0 inches at these conditions. These configurations are exposed to a more complex acoustic environment (e.g., higher-order modes) in the Curved Duct Test Rig (CDTR) at Mach 0.0 and 0.3.

This paper presents a conceptual design of a tail-cone thruster system which is operating under an axisymmetric inlet distortion. An effort to realize the targeted fuel burn saving that was proposed in NASA's STARC_ABL aircraft design is made through a CFD (Computational Fluid Dynamics)-based design approach. This method employs three iterative steps to exploit the CFD tools until the design requirements are met: a quasi-2D through-flow model to design the fan/EGV (Exit Guide Vane), a 3-D RANS (Reynolds Averaging Navier-Stokes) simulation of the single blade row to account for the inlet/fan and the EGV/nozzle interaction, and a 3-D RANS simulation of the airframe with a propulsor installed - propulsion airframe integration (PAI). The design requirements which include the thrust, and shaft power of the propulsor are matched throughout the evaluations coming from two CFD domains, i.e., the turbo-machinery and the PAI. During the switch between these different computational domains, the inlet and exit profiles are matched via the correction factors of the body-force model. The present tail-cone thruster (TCT) aerodynamic design leverages a low-pressure ratio fan (FPR=1.2 to approximately 1.25) of which the camber-line angles are predicted by a quasi-2D through-flow model. The quasi-2D model is derived to analyze the radially distorted flow resulting from the ingested boundary layer at the inlet. It also estimates the appropriate velocity vectors of the metal angles of the fan and EGV which is subjected to different types of vortex at the fan exit. The baseline geometry is revisited and its internal flow-path and exhaust cone are redesigned to illustrate the strong correlation among the components of the propulsor in the PAI domain. The peak efficiency point of the fan/EGV with respect to the blade counts, also known as solidity, and rotational speed is chosen for the cruise condition via parametric studies. The corresponding performance maps are presented. The resulting performance metrics of the new conceptual design of the BLI (Boundary Layer Ingestion) propulsor are analyzed and compared with these of the baseline in the PAI aspect. Finally, ideas of the CFD based design of a BLI propulsor are discussed based on the observations drawn from the numerical results.

Recent progress in additive manufacturing has enabled opportunities to explore novel stator rim geometries which can be implemented to improve cooling strategies in turbomachinery. This paper presents a simplified stationary geometry optimization strategy to produce enhanced stator-rotor cavity sealing and highlights main driving mechanisms.The stator and rotor rims were designed using a design strategy based on inspiration from the meandering of rivers. A minimum thickness of 2 millimeters was maintained throughout the cavity to ensure a practical implementation. The computational domain comprised of the stator outlet, hub disk leakage cavity, and rotor platform was meshed using NUMECA Int. package, Hexpress. The numerical analysis required 3D Unsteady Reynolds Average Navier-Stokes to replicate vorticial structures using Ansys Fluent. The operating conditions were representative of engine-like conditions, exploring a wide range of mass flow ratios from 1 to 3 percent. The optimization yielded designs that provide 30 percent reduction in rear platform temperature while minimizing coolant mass flow. The applicability of the design was compared against 3D sector in both stationary and in rotation.

Pressure Gain Combustion (PGC) is under investigation as a means to improve the thermal efficiency of gas turbines. PGC is a fundamentally unsteady combustion process which, through some means of confinement, raises the total pressure of the working fluid relative to the initial process state. When implemented in a combustor it yields a total pressure gain across the device instead of the typical loss seen in a conventional combustor. This pressure gain can significantly improve gas turbine performance. The tutorial will provide an introduction to the concept of PGC. It will begin with a process description in fundamental thermodynamic terms, and will quantify potential benefits. The majority of the presentation will describe the various approaches to implementation that are under investigation by the PGC.

High altitude aircraft have been used by the space photovoltaic (PV) community to determine the air mass Zero (AM0) performance of solar cells for over fifty years. Relative to in-space measurement opportunities, these methods are generally cheaper and more readily available. The data obtained, however, must be corrected for residual atmospheric effects. This paper details the correction method currently being used for the calculation of the estimated AM0 short-circuit current (Isc) for photovoltaic devices flown on the NASA ER-2 calibration platform. This method would also be applicable to other high altitude methods where Isc data is collected over a sufficiently large range of altitudes. An initial comparison with a four junction (4J) cell flown on the CASOLBA high altitude balloon platform showed an agreement to 0.2%.

Electrified Aircraft Propulsion (EAP) power systems are being studied at the NASA Electric Aircraft Testbed (NEAT) facility. The electric motors at NEAT have the capability to dynamically respond to commands that would be unrealistic when integrated with turbomachinery. There is a need to provide more realistic turbine transients for future system performance studies.

The supercritical flow model-treatment implemented in AXOD2 is unique of its kind, and unique to axial-flow turbines. It is a rather simple, one-dimensional modeling concept which utilizes and captures two supercritical flow characteristics: 1. The mass flow rate remains to be a constant in supercritical flow conditions. 2. The flow angle at the choked blade-row-discharge deflects against the blade angle.

NASA Aeronautics is advancing a variety of technologies toward the objective of reducing aviation fuel burn and emissions. Specifically, the Advanced Air Transport Technology Project under the Advanced Air Vehicles Program is investing in technologies such as small core engines, fuel-flexible combustors, and electrified aircraft propulsion, all of which offer potential for reduced fleet fuel usage and harmful emissions. This presentation will provide a brief overview of these technical approaches as well as a NASA Aeronautics budget outlook.

Two different configurations of a 7-point lean direct injector array were investigated. Chemiluminescence images of C2* or CH* were collected during combustion tests for insight on flame structure for the two configurations. Several inlet conditions were tested by varying the equivalence ratio or reference velocity. For the center right-hand 60 degree and outer right-hand 52 degree outers, the chemiluminescence emanating from the central pilot appeared well isolated from the outers. At the same time, a hollow region below the pilot showed little fluctuation of chemiluminescence where a central recirculation zone was present during the non-reacting tests. The central left-hand 60 degree and outer right-hand 52 degree configuration displayed a narrower structure from the pilot compared to the flatter pilot observed in the other configuration. Additionally, the right-handed outer swirlers may be responsible for the asymmetry observed with the chemiluminescence images. Both configurations showed less variation in chemiluminescence intensity as the reference velocity was increased. This was likely due to better atomization and vaporization associated with higher fuel and air flow rates.

This paper summarizes research on the lean direct injection (LDI) combustor concept for aero-gas turbine combustors. The focus of this paper is one particular family of lean direct injection designs, swirl-venturi lean direct injection (SV-LDI). SV-LDI is characterized by the airpath: an air swirler followed by a converging-diverging venturi. For most SV-LDI configurations, a fuel injector is inserted through the center of the air swirler, with the fuel injector tip at or near the venturi throat. Several design variables were studied. These included fuel injector tip location, air swirler blade thickness, air swirler blade angle, and fuel-air mixer size. Moving the fuel injector tip slightly upstream or downstream of the venturi throat has at most a small impact on NOx emissions. Changing the blade thickness also does not affect NOx emissions. Changing the swirler blade angle has a significant effect on NOx emissions. Decreasing swirler blade angle, and thus decreasing swirl number, decreases the NOx emissions at lower flame temperatures (below about 1800 K). However, the slope of the NOx vs. flame temperature curve is higher for lower swirl numbers. Finally, decreasing the fuel-air mixer size initially decreases NOx emissions. However, there may be an optimum fuel-air mixer size below which NOx emissions do not continue to decrease.

As part of a parametric study in which we vary swirler angle and orientation and look at their effect on fluid mixing and combustion, we examine one configuration of a 7-point lean direct injector by looking at the non-combusting 2-D velocity field using PIV (Particle Image Velocimetry), and combusting system for chemical species using chemiluminescent imaging and flame spectroscopy. The circular 7-point array consists of axial swirlers, with the center 60 degree counterclockwise swirler surrounded by six 52 degree clockwise swirlers. The velocity results for this configuration show that the outer swirlers serve to isolate the center flow field near the injector exit. A recirculation zone forms downstream of the center swirler, but not behind the outer swirlers. The combusting results also show an isolated zone directly downstream of the center injector. The flame spectra show variation in speciation of combustion species such as OH* and CH*, and as a function of position within the combustor.

An investigation was completed into the power loss associated with a rotating feed-through (RFT) design feature used to transfer lubrication and a hydraulic control signal from the static reference frame to a rotating reference frame in the NASA GRC two-speed transmission tests conducted in the Variable-Speed Drive Test Rig. The RFT feature, not commercially available, was created specifically for this research project and is integral to all two-speed transmission configurations tested, as well as a variant concept design for a geared variable-speed transmission presented at AHS Forum 71 in 2015. The experimental set-up and results from measurements in the isolated rotating-feed-through (RFT) experiments are presented. Results were used in an overall power loss assessment for a scaled conceptual 1,000 horsepower inline concentric two-speed transmission to support a NASA Revolutionary Vertical Lift Technologies (RVLT) Technical Challenge, demonstrating 50% speed change with less than 2% power loss while maintaining current power-to-weight ratios.

Rotorcraft gearbox transmissions are required to efficiently transfer power from the turbine engine to the main and tail rotor blades. Losses in transmission efficiency impact mission payload and aircraft range. These systems are expected to deliver high power with high gear pitch line velocities. More recently, shrouding has been employed to reduce windage power losses associated with the high gear rotational speeds. However, recent experimental results from tests conducted by the authors show the negative impact of close clearance shrouds on windage power loss, particularly at the meshed region where flow is ejected, or jetted, from the collapsing tooth spaces. A literature review was conducted to gain further insight into the phenomenon of gear mesh jetting and strategies to mitigate and control the associated losses. An analysis was conducted on windage losses in the mesh region. Test results are given for a modified shroud configuration. Finally, a discussion on observed trends follows with suggestions on future research.

Magnetic gearing is an alternative to mechanical gearing, where torque is transferred through magnetic force as opposed to contact force. The technology has the potential to be used in aircraft applications, without the lubrication, noise, and maintenance issues that can exist with mechanical gearing. Initial design and prototype development work was done at NASA to create a foundational understanding of the technology and the factors that influence its specific torque. The specific torque achieved through design optimization was found to be less than that of high-torque mechanical aircraft transmissions, but may be comparable to that of lower torque mechanical transmissions for electrified vertical takeoff and landing aircraft. The lessons learned from NASA's initial technology development and the direction of NASA's future work in field are discussed.

A previous system study identified significant increases in range and number of urban air mobility (UAM) missions by replacing the all battery power system of a notional UAM vehicle with an advanced diesel hybrid using conventional diesel or liquid natural gas (LNG) fuels (at constant vehicle design gross weight). Some benefits were realized using the LNG's cryogenic properties to reduce some electrical component losses and cooling requirements. Significant questions were raised concerning volume and thermal management considerations for all studied systems. The notional, baseline vehicle was a hybrid helicopter / airplane design capable of vertical take-off and landing (VTOL), balancing high cruise efficiency with reasonable hover capability. A subsequent power system assessment using the same notional vehicle and mission was performed that identified increased volume and power requirements for the active cooling required. The cooling airflow could also generate additional drag on the vehicle during operation. For the notional vehicle studied, the additional volume identified by the subsequent study would not affect vehicle mold line and therefore drag. However, the additional drag from cooling airflow and the power to circulate it as needed would impact power system and vehicle mission performance. Vehicle and mission models were updated and rerun. Updated results still indicated significant benefits in range and number of UAM missions, but reduced the benefit by 12-15%. Hold time for the hybrid systems also generally increased a few minutes because of reduced power available for charging from the power for required cooling flows. Vehicle weights, thermal loads, and cooling airflows from the updated analyses were similar to previous results.

A feasibility study was performed for an advanced commercial short-haul aircraft to evaluate the potential for increased service for short-haul flights that operate out of regional and community airports. An analysis of potential origin-destination markets and trip distances resulted in a seat capacity selection of 48 passengers and a design range of 600 NM. A down-select of advanced technologies resulted in a hybrid-electric propulsion system being chosen as the primary enabling technology. A conceptual design of the advanced aircraft was developed, and a mission and sizing analysis was performed, comparing variants of the advanced aircraft with different levels of electrification. Fairly aggressive levels of electrification and battery specific energy are needed for the hybridelectric architecture to realize any benefit in terms of total energy cost for the 600 NM design mission. The development and operational costs were estimated for the advanced aircraft and compared to the baseline. This analysis demonstrated the negative effect of the cost to develop the hybrid-electric technology on the eventual operating cost. A market analysis was performed to determine possible passenger demand for the advanced shorthaul aircraft. According to the market analysis, there is potential demand for such an aircraft, but not necessarily in many of the smaller regional and community airports that were the intended beneficiaries of this new aircraft concept.

A set of empirical jet-surface interaction noise models, developed for single-stream round nozzles exhausting over a simple surface in a static ambient, are evaluated for use in more realistic applications that include multi-stream nozzle systems with chevrons and dihedral surface geometries. The simple-single-stream models have several advantages when used in system-level noise studies: they are robust, they are quickly computed, and they are generally applicable to a wide range of configurations. However, these models rely on a fixed noise source distribution that does not account for the presence of chevrons at the nozzle exit. The effect of this omission on the prediction accuracy is shown by this comparison to experimental data. This motivates discussion of future work to develop a more robust modeling framework that can account for generalized source distributions and more complex airframe geometries. Re: Top-Mounted Propulsion (TMP17) Test Plans.

A simplified, two-dimensional, computational fluid dynamic (CFD) simulation, with a reactive Euler solver is used to examine possible causes for the low detonation wave propagation speeds that are consistently observed in air breathing rotating detonation engine (RDE) experiments. Intense, small-scale turbulence is proposed as the primary mechanism. While the solver cannot model this turbulence, it can be used to examine the most likely, and profound effect of turbulence. That is a substantial enlargement of the reaction zone, or equivalently, an effective reduction in the chemical reaction rate. It is demonstrated that in the unique flowfield of the RDE, a reduction in reaction rate leads to a reduction in the detonation speed. A subsequent test of reduced reaction rate in a purely one-dimensional pulsed detonation engine (PDE) flowfield yields no reduction in wave speed. The reasons for this are explained. The impact of reduced wave speed on RDE performance is then examined, and found to be minimal. Two other potential mechanisms are briefly examined. These are heat transfer, and reactive mixture non-uniformity. In the context of the simulation used for this study, both mechanisms are shown to have negligible effect on either wave speed or performance.

The Intelligent Control and Autonomy Branch at NASA Glenn Research Center hosted the Sixth Propulsion Control and Diagnostics Workshop on August 22-24, 2017. The objectives of this workshop were to disseminate information about research being performed in support of NASA Aeronautics programs; get feedback from peers on the research; and identify opportunities for collaboration. There were presentations and posters by NASA researchers, Department of Defense representatives, and engine manufacturers on aspects of turbine engine modeling, control, and diagnostics.

A mixer assembly for a gas turbine engine is provided, including a main mixer with fuel injection holes located between at least one radial swirler and at least one axial swirler, wherein the fuel injected into the main mixer is atomized and dispersed by the air flowing through the radial swirler and the axial swirler.

A fuel injector component includes a body, an elongate void and a plurality of bores. The body has a first surface and a second surface. The elongate void is enclosed by the body and is integrally formed between portions of the body defining the first surface and the second surface. The plurality of bores extends into the second surface to intersect the elongate void. A process for making a fuel injector component includes building an injector component body having a void and a plurality of ports connected to the void using an additive manufacturing process that utilizes a powdered building material, and removing residual powdered building material from void through the plurality of ports.

A fan section for an engine has a fan which rotates about an axis, the fan has an inlet for ingesting ambient air, and a non-axisymmetric nozzle for providing the fan with non-uniform back pressure.