Search

Abstract: Comparative analysis of the luminescent properties of Y3Al5O12:Ce (YAG:Ce) transparent optical ceramics (OС) with those of single crystal (SC) and single crystalline film (SCF) analogues has been performed under excitation by pulsed synchrotron radiation in the fundamental absorption range of YAG host. It has been shown that the properties of YAG:Ce OC are closer to the properties of the SCF counterpart, where YAl antisite defects are completely absent, rather than to the properties of SC of this garnet with large concentration of YAl antisite defects. At the same time, the luminescence spectra of YAG:Ce OC show weak emission bands in the 200–470nm range related to YAl antisite defects and charged oxygen vacancies (F+ and F centers). YAG:Ce ОС also possesses significantly larger contribution of slow components in the Ce3+ luminescence decay under high-energy excitation in comparison with SC and SCF of this garnet due to the involvement of antisite defects, charged oxygen vacancies as well as boundaries of grains in the energy transfer processes from the host to the Ce3+ ions. [ABSTRACT FROM AUTHOR]

The sol–gel derived synthesis of TiO2 films doped with Lu2O3:Tb3+ nanocrystallites and deposited on quartz or silicon substrates has been described. Their morphology have been determined by the SEM techniques. The transmission, photoluminescence and cathodoluminescence spectra have been measured. The emission decays have been measured and lifetimes for starting nanocrystalline powders and embedded nanocrystallites have been determinated. A strong influence of TiO2 matrix on the emission properties of embedded Lu2O3:Tb3+ nanocrystallites was found. [Copyright &y& Elsevier]

The study examined the possibility of intercalation of montmorillonite with neomycin in an aqueous drug solution and the factors influencing the effectiveness of this process, such as the ion exchange capacity and process conditions, including the time and temperature of incubation with the drug. X-ray diffractometry (XRD), infrared spectroscopy (FTIR), thermal analysis (DSC/TG), and Zeta potential measurement were used to confirm drug intercalation as well as to investigate the nature of clay-drug interactions. The obtained conjugates with the most favorable physicochemical properties were also tested for antibacterial response against Gram-negative bacteria ( Escherichia coli ) to confirm that the bactericidal properties of neomycin were retained after intercalation and UV-VIS spectrophotometry was used to examine the kinetics of drug release from the carrier. The results of the conducted research clearly indicate the successful intercalation of neomycin in montmorillonite and indicate the influence of process parameters on the properties of not only the conjugates themselves but also the properties of the intercalated drug, particularly its bactericidal activity. Ultimately, a temperature of 50 °C was found to be optimal for effective drug intercalation and the conjugates obtained within 2 h showed the highest antibacterial activity, indicating the highest potential of the thus-obtained montmorillonite conjugates as neomycin carriers.

Background: Protein adsorption on medical devices in contact with blood is a significant issue during renal replacement therapy. Main forces determining fouling are the electrostatic interactions between membrane and charged protein, but the dialysis membrane surface charges can be adjusted by modifying the polymer matrix to decrease the blood plasma protein adsorption., Methods: In this study, polysulfone membranes (PSU) were modified by incorporation of carbon nanoparticles such as: multiwall carbon nanotubes (2 wt.% MWCNT), graphene oxide (1 wt.% GO), and graphite (5 wt.% GR) during manufacturing process (nonsolvent-induced phase separation, NIPS). The PSU flat sheet membrane was the reference sample., Results: Observed morphology of nanocomposite membranes was similar (SEM imaging); all of them had finger-like pore structure with unimodal distribution of pore size and similar skin-to-support ratio (1:3). The carbon nanoadditives also influenced the surface wettability: hydrophobicity and surface free energy of membranes increased (polar components of energy were reduced, while the dispersive components were increased)., Conclusion: The surface charge of nanocomposite membranes increased, when the polymer matrix has been modified with CNT or GR. This significantly affects the adsorption of proteins such as chicken (CSA) and bovine serum albumin (BSA) and reduces blood clotting on the membrane., Competing Interests: Declaration of conflicting interestsThe author(s) declared no potential conflicts of interest with respect to the research, authorship, and/or publication of this article.

Here we present the cascade converter (CC), which provides real-time imaging of ionizing radiation (IoR) distribution. It was designed and manufactured with the simplest architecture, utilizing liquid crystal display (LCD) technology. Based on two merged substrates with transparent electrodes, armed with functional layers, with the cell filled with nematic liquid crystal, a display-like, IoR-stimulated CC was achieved. The CC comprises low-absorbing polymer substrates (made of polyethylene terephthalate-PET) armed with a transparent ITO electrode covered with a thin semipermeable membrane of polymer (biphenylperfluorocyclobutyl: BP-PFCB) doped with functional nanoparticles (NPs) of Lu 2 O 3 :Eu. This stack was covered with a photoconductive layer of α-Se and finally with a thin polyimide (PI) layer for liquid crystal alignment. The opposite substrate was made of LCD-type glass with ITO and polyimide aligning layers. Both substrates form a cell with a twisted structure of nematic liquid crystal (TN) driven with an effective electric field Eeff. An effective electric field driving TN structure is generated with a sum of (1) a bias voltage VBIAS applied to ITO transparent electrodes and (2) the photogenerated additional voltage VXray induced between ITO and α-Se layers with a NPs-doped BP-PFCB polymer layer in-between. The IoR (here, X-ray) conversion into real imaging of the IoR distribution was achieved in the following stages: (1) conversion of IoR distribution into non-ionizing red light emitted with functional NPs, (2) transformation of red light into an electric charge distributed in a layer of the photoconductive α-Se, which is what results in the generation of distributed voltage VXray, and (3) a voltage-mediated, distributed switching of the TN structure observed with the naked eye. The presented imaging device is characterized by a simple structure and a simple manufacturing process, with the potential for use as a portable element of IoR detection and as a dosimeter.

Aluminum garnets display exceptional adaptability in incorporating mismatching elements, thereby facilitating the synthesis of novel materials with tailored properties. This study explored Ce 3+ -doped Tb 3 Al 5-x Sc x O 12 crystals (where x ranges from 0.5 to 3.0), revealing a novel approach to control luminescence and photoconversion through atomic size mismatch engineering. Raman spectroscopy confirmed the coexistence of garnet and perovskite phases, with Sc substitution significantly influencing the garnet lattice and induced A 1g mode softening up to Sc concentration x = 2.0. The Sc atoms controlled sub-eutectic inclusion formation, creating efficient light scattering centers and unveiling a compositional threshold for octahedral site saturation. This modulation enabled the control of energy transfer dynamics between Ce 3+ and Tb 3+ ions, enhancing luminescence and mitigating quenching. The Sc admixing process regulated luminous efficacy (LE), color rendering index (CRI), and correlated color temperature (CCT), with adjustments in CRI from 68 to 84 and CCT from 3545 K to 12,958 K. The Ce 3+ -doped Tb 3 Al 5-x Sc x O 12 crystal (where x = 2.0) achieved the highest LE of 114.6 lm/W and emitted light at a CCT of 4942 K, similar to daylight white. This approach enables the design and development of functional materials with tailored optical properties applicable to lighting technology, persistent phosphors, scintillators, and storage phosphors.

The multiscale approach in designing substrates for regenerative medicine endows them with beneficial properties determining their performance in the body. Substrates for corneal regeneration should reveal the proper transparency, mechanical properties and microstructure to maintain the functionality of the regenerated tissue. In our study, series of non-wovens with different fibres orientation (random (R), aligned (A)), topography (shish-kebab (KK), core-shell (CS)) and thickness were fabricated via electrospinning. The samples were assessed for mechanical (static tensile test) and optical properties (spectroscopy UV-Vis). The research evaluated the impact of different microstructures on the viability and morphology of three cell lines (Hs 680, HaCaT and RAW 264.7). The results showed how the fibres arrangement influenced mechanical behaviour of the non-wovens. The randomly oriented fibres were more elongated (up to 50 mm) and had a lower maximum tensile force (up to 0.46 N). In turn, the aligned fibres were characterized by lower elongation (up to 19 mm) and higher force (up to 1.45 N). The conducted transparency tests showed the relation between thickness (of the non-woven and fibres) and morphology of the substrate and light transmission. To simulate the in vivo conditions, prior to the light transmission studies, samples were immersed in water. All the samples exhibited high transparency after immersion in water (>80%). The impact of various morphologies was observed in the in vitro studies. All the samples proved high cells viability. Moreover, the substrate morphology had a significant impact on the orientation and arrangement of the fibroblast cytoskeleton. The aligned fibres were oriented in exactly the same direction. The conducted research proved that, by altering the non-wovens microstructure, the properties can be adjusted so as to induce the desirable cellular reaction. This indicates the high potential of electrospun fibres in terms of modulating the corneal cell behaviour in response to the implanted substrate., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

It is well-known that the chemical composition of the host material significantly affects the spectroscopic performance of transition metal ions. However, it is worth noting that also the structure and symmetry of crystallographic sites play significant roles in transition metal ion luminescence. In this study, we demonstrate three perovskite structures of strontium titanate forming so-called Ruddlesden-Popper phases doped with Mn 4+ ions. The observed reduction in the average Ti 4+ -O 2- distance in the series SrTiO 3 -Sr 2 TiO 4 -Sr 3 Ti 2 O 7 allowed for a record-breaking shift in the spectral position of Mn 4+ emission band with a maximum of around 734 nm and led to an improvement of the already impressive thermometric performance of SrTiO 3 :Mn 4+ in ratiometric and lifetime-based approaches. This research encourages a further search for structures that, with the help of the developed correlations between structural and optical properties, could lead to the discovery of phosphors beyond the limits established so far.

Electrospinning is an increasingly popular technique for obtaining scaffolds for skin regeneration. However, electrospun scaffolds may also have some disadvantages, as the densely packed fibers in the scaffold structure can limit the penetration of skin cells into the inner part of the material. Such a dense arrangement of fibers can cause the cells to treat the 3D material as 2D one, and thus cause them to accumulate only on the upper surface. In this study, bi-polymer scaffolds made of polylactide (PLA) and polyvinyl alcohol (PVA) electrospun in a sequential or a concurrent system were investigated in a different PLA:PVA ratio (2:1 and 1:1). The properties of six types of model materials were investigated and compared i.e.; the initial materials electrospun by the sequential (PLA/PVA, 2PLA/PVA) and the concurrent system (PLA||PVA) and the same materials with removed PVA fibers (PLA/rPVA, 2PLA/rPVA, PLA||rPVA). The fiber models were intended to increase the porosity and coherent structure parameters of the scaffolds. The applied treatment involving the removal of PVA nanofibers increased the size of interfibrous pores formed between the PLA fibers. Ultimately, the porosity of the PLA/PVA scaffolds increased from 78 % to 99 %, and the time of water absorption decreased from 516 to 2 s. The change in wettability was induced by a synergistic effect of decrease in roughness after washing out and the presence of residual PVA fibers. The chemical analysis carried out confirmed the presence of PVA residues on the PLA fibers (FTIR-ATR study). In vitro studies were performed on human keratinocytes (HaKaT) and macrophages (RAW264.7), for which penetration into the inner part of the PLAIIPVA scaffold was observed. The new proposed approach, which allows the removal of PVA fibers from the bicomponent material, allows to obtain a scaffold with increased porosity, and thus better permeability for cells and nutrients., Competing Interests: Declaration of competing interest The authors declare no conflict of interest., (Copyright © 2023 Elsevier B.V. All rights reserved.)

An extracorporeal blood purification method called continuous renal replacement therapy uses a porous hollow-fiber polymeric membrane that is exposed to prolonged contact with blood. In that condition, like with any other submerged filtration membrane, the hemofilter loses its properties over time and use resulting in a rapid decline in flux. The most significant reason for this loss is the formation of a biofilm. Protein, blood cells and bacterial cells attach to the membrane surface in complex and fluctuating processes. Anticoagulation allows for longer patency of vascular access and a longer lifespan of the membrane. Other preventive measures include the modification of the membrane itself. In this article, we focused on the role of nanoadditives in the mitigation of biofouling. Nanoparticles such as graphene, carbon nanotubes, and silica effectively change surface properties towards more hydrophilic, affect pore size and distribution, decrease protein adsorption and damage bacteria cells. As a result, membranes modified with nanoparticles show better flow parameters, longer lifespan and increased hemocompatibility.

The aim of the study was to develop a method of laparoscopic embryo transfer in pigs and to compare different variants of this method. Two catheter diameters (1.6 mm and 1.0 mm), the method and site of embryo deposition (oviduct or uterus), the embryo development stage (2 - 4 cell or blastocyst), the method for oviduct or uterus stabilization, the potential for cryopreserved embryo transfer, the developmental potential of the embryos after transfer to the oviduct, patomorphology of the oviduct after transfer and possible clinical complications were taken into consideration. Two studies compared two variants of transfer to the uterus, and five variants of transfer to the fallopian tube. The transfer of embryos by the infundibulum may be of limited use due to handling problems and very low efficiency (pregnancy was not achieved). Very low efficiency was shown after transfer of vitrified embryos. Transfer to the fallopian tube by puncture of the fallopian tube, regardless of the developmental stage of the embryo, is the recommended method of embryo transfer. The histopathological examination of the fallopian tube revealed possible changes within the puncture site. The numerous clinical complications observed did not affect the effectiveness of the method., (Copyright© by the Polish Academy of Sciences.)

The aim of the work was to examine the possibility of using modified halloysite nanotubes as a gentamicin carrier and to determine the usefulness of the modification in terms of the effect on the amount of the drug attached, its release time, but also on the biocidal properties of the carriers. In order to fully examine the halloysite in terms of the possibility of gentamicin incorporating, a number of modifications of the native halloysite were carried out prior to gentamicin intercalation with the use of sodium alkali, sulfuric and phosphoric acids, curcumin and the process of delamination of nanotubes (expanded halloysite) with ammonium persulfate in sulfuric acid. Gentamicin was added to unmodified and modified halloysite in an amount corresponding to the cation exchange capacity of pure halloysite from the Polish Dunino deposit, which was the reference sample for all modified carriers. The obtained materials were tested to determine the effect of surface modification and their interaction with the introduced antibiotic on the biological activity of the carrier, kinetics of drug release, as well as on the antibacterial activity against Escherichia coli Gram-negative bacteria (reference strain). For all materials, structural changes were examined using infrared spectroscopy (FTIR) and X-ray diffraction (XRD); thermal differential scanning calorimetry with thermogravimetric analysis (DSC/TG) was performed as well. The samples were also observed for morphological changes after modification and drug activation by transmission electron microscopy (TEM). The conducted tests clearly show that all samples of halloysite intercalated with gentamicin showed high antibacterial activity, with the highest antibacterial activity for the sample modified with sodium hydroxide and intercalated with the drug. It was found that the type of halloysite surface modification has a significant effect on the amount of gentamicin intercalated and then released into the surrounding environment but does not significantly affect its ability to further influence drug release over time. The highest amount of drug released among all intercalated samples was recorded for halloysite modified with ammonium persulfate (real loading efficiency above 11%), for which high antibacterial activity was found after surface modification, before drug intercalation. It is also worth noting that intrinsic antibacterial activity was found for non-drug-intercalated materials after surface functionalization with phosphoric acid (V) and ammonium persulfate in the presence of sulfuric acid (V).

A number of Lu 2 O 3 -based materials were reported to present efficient capability of trapping excited charge carriers in metastable excited states formed either by specific dopants or naturally occurring defects. Over the years, abundant experimental data have been collected, which were taken as a solid ground to treat the problem using computational chemistry. Density functional theory (DFT) calculations with an advanced meta generalized gradient approximation (mGGA) functional were used to analyze electron trapping in cubic Lu 2 O 3 doped with Hf. Individual ions of dopant and nearest-neighbor dopant ion pairs were considered. The effects of interstitial anions such as O 2- and Cl - were analyzed. In most of the analyzed cases the additional electron charge is localized at the dopant site. However, in many of the studied cases, the dopant/defect states overlap with the conduction band and cannot correspond to electron trapping. The Hf 3+ ion in the Lu site of C 3i local symmetry ({\rm Hf}^{\times}_{{\rm Lu}-C_{\rm 3i}}) corresponds to a moderate trap depth of 0.8-0.9 eV. Several composite defects corresponding to deeper (1.1-1.4 eV) traps also exist. Unambiguous deep traps (1.5-1.8 eV) correspond to systems with Hf dopant in the cationic void, accompanied by two interstitial oxygen atoms. The results thus indicate that basic `Hf-substitutes-Lu' doping is unlikely to correspond to the deep traps observed experimentally in Lu 2 O 3 :Tb,Hf andLu 2 O 3 :Pr,Hf and more complex defects must be involved.

Emulsion electrospinning is a method of modifying a fibers' surface and functional properties by encapsulation of the bioactive molecules. In our studies, bovine serum albumin (BSA) played the role of the modifier, and to protect the protein during the electrospinning process, the W/O (water-in-oil) emulsions were prepared, consisting of polymer and micelles formed from BSA and anionic (sodium dodecyl sulfate-S) or nonionic (Tween 80-T) surfactant. It was found that the micelle size distribution was strongly dependent on the nature and the amount of the surfactant, indicating that a higher concentration of the surfactant results in a higher tendency to form smaller micelles (4-9 µm for S and 8-13 µm for T). The appearance of anionic surfactant micelles reduced the diameter of the fiber (100-700 nm) and the wettability of the nonwoven surface (up to 77°) compared to un-modified PCL polymer fibers (100-900 nm and 130°). The use of a non-ionic surfactant resulted in better loading efficiency of micelles with albumin (about 90%), lower wettability of the nonwoven fabric (about 25°) and the formation of larger fibers (100-1100 nm). X-ray photoelectron spectroscopy (XPS) was used to detect the presence of the protein, and UV-Vis spectrophotometry was used to determine the loading efficiency and the nature of the release. The results showed that the location of the micelles influenced the release profiles of the protein, and the materials modified with micelles with the nonionic surfactant showed no burst release. The release kinetics was characteristic of the zero-order release model compared to anionic surfactants. The selected surfactant concentrations did not adversely affect the biological properties of fibrous substrates, such as high viability and low cytotoxicity of RAW macrophages 264.7.

In this study, we propose a new approach in the anterior cruciate ligament (ACL) replacement to provide stability and integration with bone tunnel. A polylactide (PLA)-based tubular implant was used to support the graft stabilization in femoral and tibial bones and to stimulate the healing process after (ACL) replacement on a sheep model. The ACL was replaced with an autologous Achilles tendon split graft. The tendon-to-bone healing in the model was analyzed after 6 and 12 weeks. Two groups of animals were compared, i.e. the group with the PLA-based implant used in the ACL replacement and the control group without the implant. The knee joints were mechanically and clinically evaluated, including the histopathology tests, to determine their stability and integrity. The results indicated that the bioresorbable PLA-based tubular implant may facilitate integration of the tendon graft with bone. Remodeling the allograft inside the implant improves the joint mobility from the first week of healing: no pathological changes were observed at the surgery site and in the animals' mobility. After 6 and 12 weeks of healing no significant changes in the mechanical parameters of the knee joint were observed, regarding the joint failure force, knee displacement, angular mobility range and joint stiffness. Relatively small values of the non-destructive tests in the knee displacement, already 6 weeks after surgery, indicated the early stabilization of the knee joint. The studies showed that the failure forces of knee joints after the ACL replacement with the PLA-based implant are lower than those of an intact joint, although their biomechanical features, including strain-at- failure, are similar. The biomechanical parameters of the knee joint were significantly improved due to the selected method of attaching the autograft ends to the femoral and tibial bone surfaces. After 12 weeks the intra-tunnel tendon-bone site with the PLA implant revealed the better tibia-femur joint mechanical stability, linear force-strain function and the decreasing strain-to-failure value, as compared to the control group., (Copyright © 2021 Elsevier Ltd. All rights reserved.)

Electrospinning was used to obtain multifunctional fibrous composite materials with a matrix of poly-ɛ-caprolactone (PCL) and 2 wt.% addition of a nanofiller: montmorillonite (MMT), montmorillonite intercalated with gentamicin sulphate (MMTG) or gentamicin sulphate (G). In the first stage, the aluminosilicate gallery was modified by introducing gentamicin sulfate into it, and the effectiveness of the intercalation process was confirmed on the basis of changes in the clay particle size from 0.5 µm (for MMT) to 0.8 µm (for MMTG), an increase in the interplanar distance d 001 from 12.3 Å (for MMT) to 13.9 Å (for MMTG) and altered clay grain morphology. In the second part of the experiment, the electrospinning process was carried out in which the polymer nonwovens with and without the modifier were prepared directly from dichloromethane (DCM) and N,N-dimethylformamide (DMF). The nanocomposite fibrous membranes containing montmorillonite were prepared from the same polymer solution but after homogenization with the modifier (13 wt.%). The degree of dispersion of the modifier was evaluated by average microarray analysis from observed area (EDS), which was also used to determine the intercalation of montmorillonite with gentamicin sulfate. An increase in the size of the fibers was found for the materials with the presence of the modifier, with the largest diameters measured for PCL_MMT (625 nm), and the smaller ones for PCL_MMTG (578 nm) and PCL_G (512 nm). The dispersion of MMT and MMTG in the PCL fibers was also confirmed by indirect studies such as change in mechanical properties of the nonwovens membrane, where the neat PCL nonwoven was used as a reference material. The addition of the modifier reduced the contact angle of PCL nonwovens (from 120° for PCL to 96° for PCL_G and 98° for PCL_MMTG). An approximately 10% increase in tensile strength of the nonwoven fabric with the addition of MMT compared to the neat PCL nonwoven fabric was also observed. The results of microbiological tests showed antibacterial activity of all obtained materials; however, the inhibition zones were the highest for the materials containing gentamicin sulphate, and the release time of the active substance was significantly extended for the materials with the addition of montmorillonite containing the antibiotic. The results clearly show that the electrospinning technique can be effectively used to obtain nanobiocomposite fibers with the addition of nonintercalated and intercalated montmorillonite with improved strength and increased stiffness compared to materials made only of the polymer fibers, provided that a high filler dispersion in the spinning solution is obtained.

It was shown that carbon nonwoven fabrics obtained from polyacrylonitrile fibers (PAN) by thermal conversion may be modified on the surface in order to improve their biological compatibility and cellular response, which is particularly important in the regeneration of bone or cartilage tissue. Surface functionalization of carbon nonwovens containing C-C double bonds was carried out using in situ generated diazonium salts derived from aromatic amines containing both electron-acceptor and electron-donor substituents. It was shown that the modification method characteristic for materials containing aromatic structures may be successfully applied to the functionalization of carbon materials. The effectiveness of the surface modification of carbon nonwoven fabrics was confirmed by the FTIR method using an ATR device. The proposed approach allows the incorporation of various functional groups on the nonwovens' surface, which affects the morphology of fibers as well as their physicochemical properties (wettability). The introduction of a carboxyl group on the surface of nonwoven fabrics, in a reaction with 4-aminobenzoic acid, became a starting point for further modifications necessary for the attachment of RGD-type peptides facilitating cell adhesion to the surface of materials. The surface modification reduced the wettability ( θ ) of the carbon nonwoven by about 50%. The surface free energy (SFE) in the chemically modified and reference nonwovens remained similar, with the surface modification causing an increase in the polar component (ɣ p ). The modification of the fiber surface was heterogeneous in nature; however, it provided an attractive site of cell-materials interaction by contacting them to the fiber surface, which supports the adhesion process.

The aim of the review was to describe a complex microstructure and biomechanical properties of the articular cartilage as well as a current review of its pathologies encountered in veterinary practice. The articular cartilage with its unique features: complex microarchitecture, significant mechanical durability and elasticity, lacking blood, lymphatic vessels, and innervation, seems to stand in contradiction to the laws of biology. It can be involved in a vast majority of diseases, from osteoarthrosis as a result of natural aging process to more complex in nature like osteochondromatosis. The primary role of articular cartilage is to provide the surface for movement in any single joint in the body. Therefore, its diseases lead to physical impairment and deterioration of the quality of life. Treatment of articular cartilage poses a formidable challenge in both modern human and animal medicine., (Copyright© 2021, International Institute of Anticancer Research (Dr. George J. Delinasios), All rights reserved.)

Skin regeneration requires a three-dimensional (3D) scaffold for cell adhesion, growth and proliferation. A type of the scaffold offering a 3D structure is a nonwoven material produced via a melt-blown technique. Process parameters of this technique can be adapted to improve the cellular response. Polylactic acid (PLA) was used to produce a nonwoven scaffold by a melt-blown technique. The key process parameters, i.e., the head and air temperature, were changed in the range from 180-270 °C to obtain eight different materials (MB1-MB8). The relationships between the process parameters, morphology, porosity, thermal properties and the cellular response were explored in this study. The mean fiber diameters ranged from 3 to 120 µm. The average material roughness values were between 47 and 160 µm, whereas the pore diameters ranged from 5 to 400 µm. The calorimetry thermograms revealed a correlation between the temperature parameters and crystallization. The response of keratinocytes and macrophages exhibited a higher cell viability on thicker fibers. The cell-scaffold interaction was observed via SEM after 7 days. This result proved that the features of melt-blown nonwoven scaffolds depended on the processing parameters, such as head temperature and air temperature. Thanks to examinations, the most suitable scaffolds for skin tissue regeneration were selected.

The aim of this work was to study effect of the type of silica nanoparticles on the properties of nanocomposites for application in the guided bone regeneration (GBR). Two types of nanometric silica particles with different size, morphology and specific surface area (SSA) i.e., high specific surface silica (hss-SiO 2 ) and low specific surface silica (lss-SiO 2 ), were used as nano-fillers for a resorbable polymer matrix: poly(L-lactide-co-D,L-lactide), called PLDLA. It was shown that higher surface specific area and morphology (including pore size distribution) recorded for hss-SiO 2 influences chemical activity of the nanoparticle; in addition, hydroxyl groups appeared on the surface. The nanoparticle with 10 times lower specific surface area (lss-SiO 2 ) characterized lower chemical action. In addition, a lack of hydroxyl groups on the surface obstructed apatite nucleation (reduced zeta potential in comparison to hss-SiO 2 ), where an apatite layer appeared already after 48 h of incubation in the simulated body fluid (SBF), and no significant changes in crystallinity of PLDLA/lss-SiO 2 nanocomposite material in comparison to neat PLDLA foil were observed. The presence and type of inorganic particles in the PLDLA matrix influenced various physicochemical properties such as the wettability, and the roughness parameter note for PLDLA/lss-SiO 2 increased. The results of biological investigation show that the bioactive nanocomposites with hss-SiO 2 may stimulate osteoblast and fibroblast cells'proliferation and secretion of collagen type I. Additionally, both nanocomposites with the nanometric silica inducted differentiation of mesenchymal cells into osteoblasts at a proliferation stage in in vitro conditions. A higher concentration of alkaline phosphatase (ALP) was observed on the material modified with hss-SiO 2 silica.

Current restrictions on the use of antibiotics, associated with increases in bacterial resistance, require new solutions, including materials with antibacterial properties. In this study, copper alginate fibers obtained using the classic wet method were used to make nonwovens which were modified with arginine-glycine-aspartic acid (RGD) derivatives. Stable polysaccharide-peptide conjugates formed by coupling with 4-(4,6-dimethoxy-1,3,5-triazin-2-yl)-4-methylmorpholinium toluene-4-sulfonate (DMT/NMM/TosO - ), and materials with physically embedded RGD derivatives, were obtained. The materials were found to be characterized by very high antibacterial activity against S. aureus and K. pneumoniae . Cytotoxicity studies confirmed that the materials are not cytotoxic. Copper alginate conjugates with RGD peptides have strong potential for use in regenerative medicine, due to their biocompatibility and innate antibacterial activity.

Purpose: The aim of this study was to investigate the possibility of intercalation of gentamicin and neomycin in montmorillonite (MMT) nanofillers, as well as to study the in vitro antimicrobial properties of nanocomposite films containing a small amount of thus obtained nanofillers., Methods: The polylactide matrix (PLA) nanocomposite films with drug-intercalated montmorillonite fillers were obtained by casting after intercalation of drugs in aqueous solutions. The efficiency of intercalation has been confirmed by X-ray diffraction (XRD) and Zeta potential measurements. The materials were studied for surface wettability, roughness and mechanical properties during 6 weeks of incubation in phosphate buffer saline, and their bactericidal activity was tested against Escherichia coli bacteria before and after 6 weeks of incubation in distilled water at 37 °C. The presence of antibiotics during the incubation was monitored by conductivity and pH measurements., Results: The results indicate that nanocomposite polylactide films with montmorillonite filler intercalated with gentamicin and neomycin tend to degrade faster that their counterparts with non-intercalated fillers, which affects their mechanical properties. However, drug intercalation provided an antibacterial activity, which was confirmed by the presence of zones inhibiting the growth of Gram-negative bacteria for both antibiotics. It was also confirmed that the interaction of antibiotics with clay and polymer matrix did not adversely affect this bactericidal effect., Conclusions: Montmorillonite can be successfully intercalated with both gentamicin and neomycin, and then used as active filler for polylactide films having very good antibacterial properties, therefore their use in biomedical applications can be significantly expanded.

Purpose: The polymeric porous surface of fibres (PLA) may influence the kinetics of release of biologically active compounds (gentamicin, G and ethacridine lactate, R) affecting development of a bacterial biofilm., Methods: The porous fibres with different morphology were manufactured by the electrospinning method from ternary systems composed of PLA and selected solvents. Fibres morphology was examined using a scanning electron microscopy (SEM), their structure was analyzed by FT-IR ATR spectroscopy and differential scanning calorimetry (DSC). Changes in the drug release profile were measured using ICP/UV-Vis methods and the resulting bactericidal or bacteriostatic properties were tested by two-layer disk diffusion test in relation to various drug incorporation methods., Results: The porous fibres can be applied to produce drug-bearing membranes. The spectroscopic studies confirmed incorporation of gentamicin into the fibres and the presence of ethacridine lactate on their surface. Bimodal fibres distribution (P3) promoted faster release of gentamicin and ethacridine lactate from P3G and P3R materials. The electrospinning process coupled with the vapor induced phase separation influenced the glass transition temperature of the porous polymer fibres. The pre/post-electrospinning modification influenced the glass transition, maximum temperature of cold crystallization and melting point of the porous membrane, compared to the neat polymer. The polylactide fibres with gentamicin showed strong bactericidal effect on Gram-positive bacteria, while fibres with ethacridine lactate were bacteriostatic., Conclusions: The obtained fibres with complex surface morphology can be used as a membrane in active dressings as they make it possible to control the release profile of the active compounds.

The exact causes of failure of anterior cruciate ligament (ACL) reconstruction are still unknown. A key to successful ACL reconstruction is the prevention of bone tunnel enlargement (BTE). In this study, a new strategy to improve the outcome of ACL reconstruction was analyzed using a bioresorbable polylactide (PLA) stent as a catalyst for the healing process. The study included 24 sheep with 12 months of age. The animals were randomized to the PLA group (n = 16) and control group (n = 8), subjected to the ACL reconstruction with and without the implantation of the PLA tube, respectively. The sheep were sacrificed 6 or 12 weeks post-procedure, and their knee joints were evaluated by X-ray microcomputed tomography with a 50 μm resolution. While the analysis of tibial and femoral tunnel diameters and volumes demonstrated the presence of BTE in both groups, the enlargement was less evident in the PLA group. Also, the microstructural parameters of the bone adjacent to the tunnels tended to be better in the PLA group. This suggested that the implantation of a bioresorbable PLA tube might facilitate osteointegration of the tendon graft after the ACL reconstruction. The beneficial effects of the stent were likely associated with osteogenic and osteoconductive properties of polylactide., Competing Interests: The authors declare no conflict of interest.

Thermoluminescence of LuPO4:0.1%Yb3+ sintered ceramics was investigated and simultaneous infrared 2F5/2 → 2F7/2 and UV-blue (YbCT3+)* → O2- charge transfer emissions of the Yb3+ impurity were observed around 150 °C (423 K) for the first time. Both photons were generated by one excited Yb3+*. LuPO4:Yb3+ was thus proved to be the first system showing the quantum cutting effect in thermoluminescence. Low concentration of the dopant was proved crucial to observe an intense CT emission at so high temperatures. These data revise deeply those reported previously on the thermal quenching of Yb3+ charge transfer luminescence in orthophosphates. In was formerly claimed that CT luminescence of Yb3+ in LuPO4 and similar hosts is quenched below 300 K. Similarly, the thermoluminescent emission of LuPO4:Yb3+ above room temperature was previously reported to appear only in the IR part of the spectrum around 980 nm. Our results fundamentally change this picture and prove that CT luminescence of Yb3+ in orthophosphates appears to be significant even above 150 °C (423 K). We demonstrate the great significance of the activator concentration in its CT luminescence thermal quenching. The Yb3+ impurity ion was found to act both as an electron trap and as a recombination center. Our data open the possibility to generate intense CT luminescence of Yb3+ in orthophosphates at room temperature and above which may make such phosphors rational for applications previously considered unattainable for them.

The aims of this study were to identify the short aromatic peptides which are able to form highly ordered amyloid-like structures in self-assembling processes, to test the influence of length of hydrophobic peptides on tendency to aggregation, and to check if aggregated peptides fulfill requirements expected for materials useful for scaffolding. All tested hydrophobic peptides were prepared on solid phase by using DMT/NMM/TsO - as a coupling reagent. The progress of aggregation was studied by set of independent tests. All aggregated peptides were found stable under in vitro conditions. All fibrous material formed by self-assembling of peptides does not show any cytotoxic effects on L929 fibroblast cells. Peptides containing tyrosine and tryptophan residues even effectively accelerated the proliferation and stimulated the activity of L929 fibroblasts., (© 2019 Wiley-VHCA AG, Zurich, Switzerland.)

This study represents the unique analysis of the electrospun scaffolds with the controlled and stable surface potential without any additional biochemical modifications for bone tissue regeneration. We controlled surface potential of polyvinylidene fluoride (PVDF) fibers with applied positive and negative voltage polarities during electrospinning, to obtain two types of scaffolds PVDF(+) and, PVDF(-). The cells' attachments to PVDF scaffolds were imaged in great details with advanced scanning electron microscopy (SEM) and 3D tomography based on focus ion beam (FIB-SEM). We presented the distinct variations in cells shapes and in filopodia and lamellipodia formation according to the surface potential of PVDF fibers that was verified with Kelvin probe force microscopy (KPFM). Notable, cells usually reach their maximum spread area through increased proliferation, suggesting the stronger adhesion, which was indeed double for PVDF(-) scaffolds having surface potential of -95 mV. Moreover, by tuning the surface potential of PVDF fibers, we were able to enhance collagen mineralization for possible use in bone regeneration. The scaffolds built of PVDF(-) fibers demonstrated the greater potential for bone regeneration than PVDF(+), showing after 7 days in osteoblasts culture produce well-mineralized osteoid required for bone nodules. The collagen mineralization was confirmed with energy dispersive X-ray spectroscopy (EDX) and Sirius Red staining, additionally the cells proliferation with fluorescence microscopy and Alamar Blue assays. The scaffolds made of PVDF fibers with the similar surface potential to the cell membranes promoting bone growth for next-generation tissue scaffolds, which are on a high demand in bone regenerative medicine.

Purpose: Physiotherapy with the use of pulsed magnetic fields is one of the methods of activating the processes of bone healing and regeneration. Exposing materials serving as membranes in guided bone regeneration (GBR) or guided tissue regeneration (GTR) to magnetic fields is an effective model that allows to monitor changes in the material under the influence of the magnetic field., Methods: Materials engineering methods were used to verify the extent of material degradation resulting from magnetic field exposure in an aqueous environment. Changes in surface morphology were observed under an optical microscope and a scanning electron microscope (SEM). Changes in surface wettability were analysed in relation to the direct contact angle. Chemical structural changes were verified with the use of infrared spectroscopy (FTIR-ATR)., Results: The PCL-based membrane materials underwent relatively moderate surface degradation (altered contact angle, changes in surface morphology), but the absence of observable FTIR-ATR spectral shifts evidenced material stability under the influence of magnetic field. More extensive degradation processes were observed in the case of PLDLA-based materials, whose surface character changed from hydrophilic to hydrophobic. The spectra revealed enhanced intensity of the chain terminal groups, provided that modifiers (nanometric SiO2 and TCP (water reservoir)) were present in the polymer matrix., Conclusions: The extent degradation in the polymer membrane was primarily dependent on the presence of aqueous environment, while the influence of the magnetic field on the analysed membrane materials was negligible. Therefore, GBR/GTR membrane implants can be considered to remain stable during rehabilitation with the use of alternating magnetic field.

The aim of this study was to verify whether L-lactide/DL-lactide copolymer 80/20 (PLDLLA) and platelet-rich plasma (PRP) trigger bone formation within critical-sized calvarial defects in adult sheep ( n = 6). Two craniectomies, each ca. 3 cm in diameter, were created in each animal. The first craniectomy was protected with an inner polylactide membrane, filled with PRP-polylactide granules, and covered with outer polylactide membrane. The second control craniectomy was left untreated. The animals were euthanized at 6, 7, 17, 19, 33, and 34 weeks after surgery, and the quality and the rate of reossification were assessed histomorphometrically and microtomographically. The study demonstrated that application of implants made of PLDLLA 80/20 combined with an osteopromotive substance (e.g., PRP) may promote bone healing in large calvarial defect in sheep. These promising proof-of-concept studies need to be verified in the future on a larger cohort of animals and over a longer period of time in order to draw definitive conclusions.

Adsorption or immobilization of proteins on synthetic surfaces is a key issue in the context of the biocompatibility of implant materials, especially those intended for the needs of cardiac surgery but also for the construction of biosensors or nanomaterials used as drug carriers. The subject of research was the analysis of Raman spectra of two types of fibrous carbon nanomaterials, of great potential for biomedical applications, incubated with human serum albumin (HSA). The first nanomaterial has been created on the layer of MWCNTs deposited by electrophoretic method (EPD) and then covered by thin film of pyrolytic carbon introduced by chemical vapor deposition process (CVD). The second material was formed from carbonized nanofibers prepared via electrospinning (ESCNFs) of polyacrylonitrile (PAN) precursor and then covered with pyrolytic carbon (CVD). The G-band blue-shift towards the position of about 1600cm -1 , observed for both studied surfaces, clearly indicates the albumin (HSA) adhesion to the surface. The G and G' (2D) peak shift was employed to assess the stress build up on the carbon nanomaterials. The surface nano- and micro-topography as well as the method of ordering the carbon nanomaterial has a significant influence on the mode of surface-protein interaction., (Copyright © 2018 Elsevier B.V. All rights reserved.)

Luminescence properties of SrS:Ce pellets sintered at 1700 °C were investigated under high pressure. Two different Ce3+-related emissions were confirmed to appear in the blue-green and red parts of the spectrum and were shown to shift significantly and linearly to longer wavelengths with increasing pressure. Changes in decay times of both emissions were also thoroughly analyzed. The results confirmed that Ce3+ ion pairing/clustering occurring due to their enhanced mobility at high temperatures is responsible for the appearance of the recently reported red Ce3+ emission in sintered SrS:Ce pellets.

This study investigates the propensity of short peptides to self-organize and the influence of aggregates on cell cultures. The dipeptides were derived from both enantiomers of identical aromatic amino acids and tripeptides were prepared from two identical aromatic amino acids with one cysteine or methionine residue in the C-terminal, N-terminal, or central position. The formation or absence of fibrous structures under physiological conditions was established using Congo Red and Thioflavine T assays as well as by microscopic examination using normal and polarized light. The in vitro stability of the aggregates in buffered saline solution was assessed over 30 days. Materials with potential for use in regenerative medicine were selected based on the cytotoxicity of the peptides to the endothelial cell line EA.hy 926 and the wettability of the surfaces of the films, as well as using scanning electron microscopy. The criteria were fulfilled by H- d Phe d Phe-OH, H- d Cys d Phe d Phe-OH, H-CysTyrTyr-OH, H- d Phe d Phe d Cys-OH, H-TyrTyrMet-OH, and H-TyrMetTyr-OH. Our preliminary results suggest that the morphology and cell viability of L919 fibroblast cells do not depend on the stereochemistry of the self-organizing peptides.

Purpose: Skin substitutes are heterogeneous group of scaffolds (natural or synthetic) and cells. We hypothesize that nanofibers with layer composition made of polylactide (PLA) and sodium hyaluronate (HA) obtained using electrospinning method are a good matrix for cell adhesion and proliferation., Methods: Optimal conditions of electrospinning of PLA and HA nanofibers to create layered compositions (PLA membrane covered with HA nonwovens) were determined by modifying parameters such as the appropriate amount of solvents, polymer concentration, mixing temperature and electrospinning process conditions. By changing the parameters, it was possible to control the diameter and properties of both polymer fibers. The spinning solution were characterized by surface tension and rheology. A scanning electron microscope (SEM) was used to determine the morphology and fiber diameters: PLA and HA. Structure of the PLA/HA nonwoven was analyzed using spectroscopy (FTIR/ATR). Biocompatibility of the nonwoven with fibroblasts (ECM producers) was assessed in the in vitro conditions., Results: The results showed that stable conditions for the formation of submicron PLA fibers were obtained using a 13% wt. solution of the polymer, dissolved in a 3:1 mixture of DCM:DMF at 45 °C. The hyaluronic fibers were prepared from a 12% wt. solution of the polymer dissolved in a 2:1 mixture of ammonia water and ethyl alcohol. All materials were biocompatible but to a different degree., Conclusions: The proposed laminate scaffold was characterized by a hydrophobic-hydrophilic domain surface with a maintained fiber size of both layers. The material positively underwent biocompatibility testing in contact with fibroblasts.

Aim: To evaluate the utility of a novel nanocomposite biomaterial consisting of poly-L/D-lactide, and hydroxyapatite bioceramics, enriched with sodium alginate in articular cartilage defect treatment., Materials and Methods: The biomaterial was prepared using the method of solvent casting and particle leaching. The study was conducted on 20 New Zealand White rabbits. Experimental osteochondral defects were created in the femoral trochlear grooves and filled with biomaterials. In control groups, the defects were left to spontaneously heal. The quality of newly-formed tissue was evaluated on the basis of macroscopic and histological assessment. Additionally the level of osteogenic and cartilage degradation markers were measured., Results: The majority of the defects from the treatment group were covered with tissue similar in structure and colour to healthy cartilage, whereas in the control group, tissue was uneven, and not integrated into the surrounding cartilage., Conclusion: The results obtained validate the choice of biomaterial used in this study as well as the method of its application., (Copyright© 2017, International Institute of Anticancer Research (Dr. George J. Delinasios), All rights reserved.)

The present work focuses on the state-of-the-art of biodegradable ceramic-polymer composites with particular emphasis on influence of various types of ceramic fillers on properties of the composites. First, the general needs to create composite materials for medical applications are briefly introduced. Second, various types of polymeric materials used as matrices of ceramic-containing composites and their properties are reviewed. Third, silica nanocomposites and their material as well as biological characteristics are presented. Fourth, different types of glass fillers including silicate, borate and phosphate glasses and their effect on a number of properties of the composites are described. Fifth, wollastonite as a composite modifier and its effect on composite characteristics are discussed. Sixth, composites containing calcium phosphate ceramics, namely hydroxyapatite, tricalcium phosphate and biphasic calcium phosphate are presented. Finally, general possibilities for control of properties of composite materials are highlighted., (Copyright © 2016 Elsevier B.V. All rights reserved.)

The present paper concerns the potential use of montmorillonite as a drug carrier and focusses on the intercalation of the studied clay with gentamicin (an aminoglycoside antibiotic) at various temperatures (20, 50 and 80°C). The experiments were performed to identify the temperature required for the optimum intercalation of gentamicin into the interlayer of montmorillonite. The structural and microstructural properties of gentamicin and the potential for introducing it between smectite clay layers were investigated by means of X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopic techniques, and SEM with EDS analysis. Additionally, the in vitro drug release behaviour of the montmorillonite-gentamicin complex and its antibacterial activity against Escherichia coli (E. coli) bacteria was investigated. Based on these studies, the impact of temperature on the intercalation of the drug between layers of smectite was evaluated. It was found that an intercalation temperature of 50°C resulted in the highest shift in the position of principle peak d (001) as measured by XRD, suggesting, that the greatest amount of gentamicin had been introduced into the interlayer space of montmorillonite at this temperature. Subsequently, the montmorillonite-gentamicin complex material obtained at 50°C revealed the greatest capacity for killing E. coli bacteria during an in vitro test., (Copyright © 2016 Elsevier B.V. All rights reserved.)

In this study, two different composition gel derived silica-rich (S2) or calcium-rich (A2) bioactive glasses (SBG) from a basic CaO-P2 O5 -SiO2 system were incorporated into poly(ε-caprolactone) (PCL) matrix to obtain novel bioactive composite scaffolds for bone tissue engineering applications. The composites were fabricated in the form of highly porous 3D scaffolds using following preparation methods: solvent casting particulate leaching (SCPL), solid-liquid phase separation, phase inversion (PI). Scaffolds containing 21% vol. of each bioactive glass were characterized for architecture, crystallinity, hydrolytic degradation, surface bioactivity, and cellular response. Results indicated that the use of different preparation methods leads to obtain highly porous (60-90%) materials with differentiated morphology: pore shape, size, and distributions. Thermal analysis (DSC) showed that the preparation method of materials and addition of bioactive glass particles into polymer matrix induced the changes of PCL crystallinity. Composites obtained by SCPL and PI method containing A2 SBG rapidly formed a hydroxyapatite calcium phosphate surface layer after incubation in SBF. Bioactive glasses used as filler in composite scaffolds could neutralize the released acidic by-products of the polymer degradation. Preliminary in vitro biological studies of the composites in contact with osteoblastic cells showed good biocompatibility of the obtained materials. Addition of bioactive glass into the PCL matrix promotes mineralization estimated on the basis of the ALP activity. These results suggest that through a process of selection appropriate methods of preparation and bioglass composition it is possible to design and obtain porous materials with suitable properties for regeneration of bone tissue., (© 2014 Wiley Periodicals, Inc.)

Purpose: The purpose of the study was to assess the biocompatibility of porous terpolymer (polytetrafluoroethylene-co-polyvinylidene fluoride-co-polypropylene, PTFE-PVDF-PP) membranes as an implant material to be placed during nonpenetrating very deep sclerectomy (NPVDS). Another study objective was to determine whether the polymer membrane under investigation could be used to manufacture a new-generation implant, which would actively delay the process of fistula closure and facilitate aqueous humor drainage., Methods: Histological response and tissue tolerance of the implant material were assessed. The study was performed on 38 eyeballs of 19 New Zealand white rabbits (19 implanted, 19 control). Histological assessment was carried out between 2 and 52 weeks after surgery. We routinely assessed inflammatory infiltrate, neovascularization, hemorrhage, and stromal edema as well as connective tissue attachment to the implant and adjacent tissues., Results: At 52 weeks of observation, a statistically significant difference was revealed between the study and control groups in terms of resorptive granulation, tissue, and the inflammatory infiltrate. No features of acute inflammatory response to the implant were observed, and there was an absence of histological features of acute inflammatory infiltrates and subsidence of chronic inflammatory infiltrates and resorptive granulation over time., Conclusions: Slight fibrotic response and insignificant changes in neighboring eye tissues all indicate good tolerance to bioimplant materials. This allows for some optimism regarding the use of hydrophobic terpolymer in the construction of new intrascleral implants. However, the ultimate decision regarding its usefulness and safety in the treatment of glaucoma requires further investigation.

Purpose: The aim of the study was to evaluate the influence of an implant made of a terpolymer (PTFE-PVDF-PP) on the condition of rabbit eyes during a one year observation period., Methods: The implant in the shape of an equilateral triangle (3 mm side length) was manufactured from a thin hydrophobic porous membrane. There were evaluated 40 eyes of 20 rabbits. The animals had non-penetrating very deep sclerectomy (NPVDS) performed, with insertion of an implant in the form of a triangular thin membrane. The control group consisted of 20 eyes where the animals had NPVDS performed without implant insertion. The evaluations included the study of the anterior part of the eye together with photographic documentation. Histopathological examination of the eyes 52 weeks after NPVDS procedure has been made. The process of wound healing was comparable in both groups., Results: The evaluation of the rabbits did not reveal any acute process of intraocular inflammation. After 12 month period of observation, no statistically significant differences in the process of wound healing or status of eyes were found between the groups. An analysis of fibrous connective tissue attachment to the implant showed that its layer was not thick and did not differ significantly from the control. The procedure of very deep sclerectomy and insertion of a polymer implant were well tolerated by the rabbit eyes., Conclusions: The in vivo results indicate that the hydrophobic implant in the form of a membrane can serve as a sclera implant after further study.

Li₂SO₄ or (Li₂SO₄ + SiO₂)-mixture fluxes were used to prepare a Lu₂O₃:Eu powder phosphor as well as an undoped Lu₂O₃ utilizing commercial lutetia and europia as starting reagents. SEM images showed that the fabricated powders were non-agglomerated and the particles sizes varied from single microns to tens of micrometers depending largely on the flux composition rather than the oxide(s)-to-flux ratio. In the presence of SiO₂ in the flux, certain grains grew up to 300-400 μm. The lack of agglomeration and the large sizes of crystallites allowed making single crystal structural measurements and analysis on an undoped Lu₂O₃ obtained by means of the flux technique. The cubic structure with a = 10.393(2) Å, and Ia space group at 298 K was determined. The most efficient radioluminescence of Lu₂O₃:Eu powders reached 95%-105% of the commercial Gd₂O₂S:Eu.

Lu₂O₃:Pr,Hf ceramics were investigated using mainly thermoluminescence (TL) technique. Their ability to efficiently store energy acquired upon irradiation with X-rays was proven. The best TL performance was achieved for compositions containing 0.025%-0.05% of Pr and about 0.1% of Hf. Further enhancement of TL efficiency was attained by increasing the temperature of sintering of the ceramics up to 1700 °C and applying reducing atmosphere of forming gas. It was also proven that fast cooling after the sintering at 1700 °C significantly enhanced the storage phosphor performance. TL glow curve contained three components peaking around 130, 250 and 350 °C. Among them, the one at 250 °C contributed the most to the total TL.

This work concerns the production of fibrous composite materials based on biodegradable polymers such as alginate, dibutyryl chitin (DBC) and poly-ε-caprolactone (PCL). For the production of fibres from these polymers, various spinning methods were used in order to obtain composite materials of different composition and structure. In the case of alginate fibres containing the nanoadditive tricalcium phosphate (TCP), the traditional method of forming fibres wet from solution was used. However in the case of the other two polymers the electrospinning method was used. Two model systems were tested for biocompatibility. The physicochemical and basic biological tests carried out show that the submicron fibres produced using PCL and DBC have good biocompatibility. The proposed hybrid systems composed of micrometric fibres (zinc and calcium alginates containing TCP) and submicron fibres (DBC and PCL) meet the requirements of regenerative medicine. The biomimetic fibre system, the presence of TCP nanoadditive, and the use of polymers with different resorption times provide a framework with specific properties on which bone cells are able to settle and proliferate.

Tricalcium diyttrium trisilicon oxide, Ca(3)Y(2)(SiO(4))(3) doped with Eu(2+) and Eu(3+) belongs to a very limited number of hosts able to accommodate both Eu(3+) and Eu(2+) ions, which might make it useful for white light emitting diodes (WLEDs) based on UV chip technology. In this contribution we present a detailed study of photoluminescence kinetics and high pressure spectroscopy of Eu(3+) and Eu(2+) doped Ca(3)Y(2)(SiO(4))(3). At ambient pressure and room temperature, under excitation with near-UV radiation, a broad emission band from 400 to 550 nm due to the 4f(6)5d(1)→4f(7)((8)S(7/2)) transition in Eu(2+) was observed, as well as several emission peaks in the region between 550 and 710 nm, ascribed to the (5)D(0)→ (7)F(J) (J = 0-4) transitions in Eu(3+). The bluish green luminescence related to Eu(2+) in the Ca(3)Y(2)(SiO(4))(3) exhibits a small red pressure-induced shift reaching -5.2 cm(-1)/kbar. The red shifts of the luminescence lines related to Eu(3+) ion emission vary from 0.15 to -0.54 cm(-1)/kbar. Time-resolved photoluminescence was measured at different temperatures and pressures. Luminescence decay traces were studied for the bluish green emission band of Eu(2+) and for the red emission peak due to the (5)D(0) →  (7)F(2) transition of Eu(3+). Decay times slightly decreased with increasing pressure.

Background: Kinesio Taping is currently regarded by physiotherapists as a method supporting rehabilitation and modulating some physiological processes. It is employed e.g. in orthopaedics and sport medicine. This sensory method supports joint function by exerting an effect on muscle function, enhancing activity of the lymphatic system and endogenous analgesic mechanisms as well as improving microcirculation. The aim of the study was to determine the effect of Kinesio Taping on changes in the tone of the vastus medialis muscle during isometric contractions., Material and Method: The study group included 27 healthy persons. A Kinesio Tape was placed to support the function of the medial head of the quadriceps muscle of thigh. Transdermal EMG was used to assess bioelectrical activity of the muscle. A standardised protocol was employed for measurement of muscle tone, recorded as the peak torque of the muscle., Results: An examination performed 24 hours after the placement of the Kinesio Tape revealed significantly increased recruitment of the muscle's motor units, as expressed by peak torque. An examination performed after 72 hours of kinesio taping showed a statistically significant increase in bioelectrical activity of the muscle. However, this was lower than the effect at 24 hours. In the group where the tapes were removed after 24 hours, high torque was still maintained., Conclusions: 1. Clinically significant effects of Kinesio Taping in this study included an increase in the bioelectrical activity of the muscle after 24 hours of kinesio taping and the maintenance of this effect for another 48 hours following removal of the tape. 2. The decrease in muscle tone to the baseline value, which was observed during the fourth day of Kinesio Taping use, may have resulted from the time of effective use of the KT tape being shorter than previously believed and may restrict Kinesio Taping use. 3. Kinesio Taping used shortly before the motor activity it is supposed to support may fail to fulfil its function.