Search

This study evaluated the corrosion kinetics and surface topography of Ti-6Al-4V alloy exposed to mouthwash solutions (0.12% chlorhexidine digluconate, 0.053% cetylpyridinium chloride and 3% hydrogen peroxide) compared to artificial saliva (pH6.5) (control). Twenty Ti-6Al-4V alloy disks were used and divided into 4 groups (n=5). For the electrochemical assay, standard tests as open circuit potential and electrochemical impedance spectroscopy (EIS) were applied at baseline, 7 and 14days after immersion in the solutions. Scanning electron microscopy, atomic force microscopy and profilometry (average roughness - Ra) were used for surface characterization. Total weight loss of disks was calculated. Data were analyzed by ANOVA and Bonferroni's test (α=0.05). Hydrogen peroxide generated the lowest polarization resistance (Rp) values for all periods (P<0.05). For the capacitance (Cdl), similar results were observed among groups at baseline (P=0.098). For the 7 and 14-day periods, hydrogen peroxide promoted the highest Cdl values (P<0.0001). Hydrogen peroxide promoted expressive superficial changes and greater Ra values than the others (P<0.0001). It could be concluded that solutions containing cetylpyridinium chloride and chlorhexidine digluconate might be the mouthwashes of choice during the post-operatory period of dental implants. However, hydrogen peroxide is counter-indicated in these situations. Further studies evaluating the dynamics of these solutions (tribocorrosion) and immersing the disks in daily cycles (two or three times a day) to mimic a clinical situation closest to the application of mouthwashes in the oral cavity are warranted to prove our results., (Copyright © 2014 Elsevier B.V. All rights reserved.)

Procedures for the surgical correction of dentofacial deformities may produce important complications, whether due to the potential for vascular injury or to prolonged surgery, both of which may lead to severe blood loss. Fluid replacement with crystalloid, colloid, or even blood products may be required. The aim of this study was to assess blood loss and transfusion requirements in 45 patients (18 males and 27 females; mean age 29.29 years, range 16-52 years) undergoing orthognathic surgery, assigned to one of two groups according to procedure type-rapid maxillary expansion or double-jaw orthognathic surgery. Preoperative hemoglobin and hematocrit levels and intraoperative blood loss were measured. There was a substantial individual variation in pre- and postoperative hemoglobin values (10.3-17 and 8.8-15.4 g/dL, respectively; p < 0.05). Mean hematocrit values were 41.53 % preoperatively (range 31.3-50.0 %) and 36.56 % postoperatively (range 25-43.8 %) (p < 0.05). Mean blood loss was 274.60 mL (range 45-855 mL). Only two patients required blood transfusion. Although blood loss and transfusion requirements were minimal in the present study, surgical teams should monitor the duration of surgery and follow meticulous protocols to minimize the risks.

Condylar hyperplasia (CH) is a pathologic condition that causes overdevelopment of the condylar head and neck as well as the mandible. Slowly progressive unilateral enlargement of the head and the neck of the condyle causes crossbite malocclusion, facial asymmetry, and shifting of the midpoint of the chin to the unaffected side. The etiology and the pathogenesis of CH remain uncertain. The diagnosis is made by clinical and radiologic examinations and bone scintigraph. A difference in uptake of 10% or more between condyles is regarded as indicative of CH, and the affected condyles had a relative uptake of 55% or more. When the diagnosis of active CH is established, the treatment consists of removal of the growth center by a partial condylectomy. The authors present the case of a 46-year-old male patient with right active type II CH or hemimandibular hyperplasia who underwent a high condylectomy.

We evaluated the influence of bone tissue type on stress distribution in full-arch implant-supported fixed prostheses using a three-dimensional finite element analysis. Stresses in cortical and trabecular bones were also investigated. Edentulous mandible models with four implants inserted into the interforaminal region were constructed from different bone types: type 1 - compact bone; type 2 - compact bone surrounding dense trabecular bone; type 3 - a thin layer of compact bone surrounding trabecular bone; and type 4 - low-quality trabecular bone. The mandible was restored with a full-arch implant-supported fixed prosthesis. A 100-N oblique load was applied to the left lower first molar of the prosthesis. The maximum (σmax) and minimum (σmin) principal stress values were determined. The σmax in the type 4 cortical bone was 22.56% higher than that in the type 1 bone. The σmin values in the cortical bone were similar among all the bone types. For the superstructure, increases of 9.04% in the σmax and 11.74% in the σmin in G4 (type 4 bone) compared with G1 (type 1 bone) were observed. For the implants, the highest stress values were located in G4, and the lowest values were observed in G1. In the trabecular bone, the highest stress was generated in G1 and G2. In conclusion, the more compact bones (types 1 and 2) are the most suitable for supporting full-arch implant-supported fixed prostheses, and poor bone quality may increase the risk of biological and mechanical failure., (Copyright © 2014 Elsevier B.V. All rights reserved.)

This study evaluated the stress distribution in mandibular full-arch implant-supported fixed dentures with different veneering and metallic infrastructure materials, using three-dimensional finite element analysis. Ten models were obtained from an edentulous human mandible with a complete denture fixed by four implants. Acrylic resin (RES) and porcelain (POR) teeth were associated with infrastructures of titanium (Ti), gold (Au), silver-palladium (AgPd), chrome-cobalt (CoCr) and nickel-chrome (NiCr). A 100-N oblique was applied. The von Mises (σvM) and maximum (σmax) and minimum (σmin) principal stresses were obtained. The RES-AgPd group showed the lowest σvM values, while the RES-Ni-Cr group showed the highest. In the bone tissue, the RES-Au group was the only one that showed different σmax values with a 12% increase in comparison to the other groups which had similar stress values. In the implants, the groups with Ti, Au and AgPd infrastructures, either with porcelain or resin teeth, showed σvM values similar and lower in comparison to the groups with CoCr and NiCr infrastructures. The tooth veneering material influenced the stress values in metallic infrastructures, in which the acrylic resin had the highest values. The veneering and infrastructure materials have influence on stress values of implant-supported dentures, except for the peri-implant bone tissue., (© 2013.)

Background: Surgical approaches to temporomandibular region have been the subject of numerous controversies in the literature. Pre-auricular approaches have been used with the observance of high success rate, and during surgery history, various modifications of this approach were conducted in order to reduce irreversible sequelae. Thus, given the relevance of the study, this article proposes to alert the professionals that carry out these surgical approaches in relation to the anatomical structures involved and to describe and emphasise the benefits of endaural approach., Case Report: A Caucasian male patient, victim of a firearm injury, sustained a wound on the right pre-auricular region, and at the time of assessment, he complained of pain, mouth opening difficulty and dysphagia. On physical examination, there was oedema and ecchymosis in the right periorbital region. In the radiological examination, a foreign body compatible with a firearm projectile was observed in the right pre-auricular region, being in accordance with the information collected. The endaural incision and divulsion by plans was then made until the projectile., Discussion: For proper exposure of the region, several studies were designed to evaluate the patterns of branching and anastomosis of the facial nerve. As for the best cosmetic result with the different pre-auricular approaches, the endaural approach was described as an approach that offers great cosmetic results because the incision design guides the surgeon in the wound closure and causes a decrease in the tension of flap, unlike that observed by some authors.

Titanium is a metallic element known by several attractive characteristics, such as biocompatibility, excellent corrosion resistance and high mechanical resistance. It is widely used in Dentistry, with high success rates, providing a favorable biological response when in contact with live tissues. Therefore, the objective of this study was to describe the different uses of titanium in Dentistry, reviewing its historical development and discoursing about its state of art and future perspective of its utilization. A search in the MEDLINE/PubMed database was performed using the terms 'titanium', 'dentistry' and 'implants'. The title and abstract of articles were read, and after this first screening 20 articles were selected and their full-texts were downloaded. Additional text books and manual search of reference lists within selected articles were included. Correlated literature showed that titanium is the most used metal in Implantology for manufacturing osseointegrated implants and their systems, with a totally consolidated utilization. Moreover, titanium can be also employed in prosthodontics to obtain frameworks. However, problems related to its machining, casting, welding and ceramic application for dental prosthesis are still limiting its use. In Endodontics, titanium has been used in association to nickel for manufacturing rotatory instruments, providing a higher resistance to deformation. However, although the different possibilities of using titanium in modern Dentistry, its use for prostheses frameworks still needs technological improvements in order to surpass its limitations.

Dental trauma has been considered as a public health problem that affects mainly children and youngsters and due to its impact on the patient's quality of life. This study presents the results of a 6-year survey of the occurrence and characteristics of dental trauma in patients admitted to the Service of Surgery and Oral and Maxillofacial Traumatology of the School of Dentistry of Araçatuba (UNESP, Brazil) after emergency care in hospital facilities in the region of Araçatuba, SP, Brazil. For such purpose, the clinical files of patients treated at the Service between 1999 and 2005 were reviewed. Information regarding gender, age, number of traumatized teeth, etiology and diagnosis of the trauma was collected from the files of patients with tooth injuries and recorded in case report forms specifically designed for this purpose. The results showed that from a total of 4112 patients admitted to the Service within the surveyed period, 266 (6.5%) had tooth injuries (172 males - 64.7%; 94 females - 35.3%). The total number of traumatized teeth was 496. Most patients belonged to the 16-20 year-old age group (20.3%) and the most frequent causes of tooth injuries were bicycle accidents (28.6%), motorcycle accidents (19.2%) and falls (18.8%). Injuries to the periodontal tissues were the most frequent type of tooth injuries (408 teeth; 82.26%), occurring in 118 primary and 290 permanent teeth. Among the injuries to the periodontal tissues, avulsion was the most common (32.86%) (29.41% for primary and 34.0% for permanent teeth), followed by extrusive luxation (19.15%) (25.21% for primary and 17.24% for permanent teeth). In conclusion, in the surveyed population, cases of tooth injuries were more frequent in males aged 16-20 years old due to cyclist accidents with predominance of injuries to the periodontal tissues, in particular, avulsions.