Search

There are many factors that influence filling body stability in partial-filling mining. In deep mining, filling rate and internal friction angle of filling body are the main factors that greatly influence both sides of plasticity zone breadth in the process of filling bodys deformation and destruction. Taking filling rate and friction angle as the main variables to make a numerical simulation analysis on the deep mine working face, we can find a conclusion that it shows a concave-down power exponent relationship between the width of plasticity zone and the filling rate; With lower filling rate, it shows a concave-up power exponent relationship with friction angle, and the relationship of power exponent will change into the linearity as the filling rate increase.

The structural transitions of Ti3AlC2 induced by ion irradiation were investigated over a wide fluence range by transmission electron microscopy. No amorphization occurs even at the highest dose of 31 dpa, indicating a great tolerance to irradiation-induced amorphization. Dynamic electron diffraction simulations and high-resolution observations indicate that the nanolamellar structure of Ti3AlC2 is readily destroyed through the formation of antisite defects and a phase transformation from α-Ti3AlC2 to β-Ti3AlC2 occurs at 2.61 dpa. A great number of stacking faults in basal planes are formed with increasing fluence, leading to the formation of nano Ti3AlC2 grains with different stacking sequences at 10.45 dpa. Serious structural damage and polygonization are observed at the highest dose of 31 dpa. Due to the similar structural transition process with some complex oxides (pyrochlore and murataite), it is assumed that the great irradiation tolerance of Ti3AlC2 results from the low formation energy of antisite defects. These findings first clarify the structural transition mechanism of Ti3AlC2 under ion irradiation and its relationship with irradiation tolerance, which is of vital importance in understanding the irradiation response of MAX phases and provides a clue in searching for materials with higher irradiation tolerance from MAX phases.

For treating severe faecal incontinence, the authors developed an intelligent artificial anal sphincter system (AASS) equipped with a feedback sensor that utilized a transcutaneous energy transfer system (TETS). To deliver the correct amount of power (i.e. to match the load demand under variable coupling conditions caused by changes in positioning between the coils due to fitting and changes in posture), a regulating method to stabilize output voltage with a closed loop variable-frequency controller was developed in this paper. The method via which the voltage gain characteristics of a voltage-fed series-tuned TETS were derived is also described. The theoretical analysis was verified by the results of the experiment. A numerical analysis method was used as a control rule with respect to the relationship between operating frequency and output voltage. To validate the feedback control rules, a prototype of the TET charging system was constructed, and its performance was validated with the coupling variation between 0.12-0.42. The results show that the output voltage of the secondary side can be maintained at a constant 7 V across the whole coupling coefficient range, with a switching frequency regulation range of 271.4-320.5 kHz, and the proposed controller has reached a maximal end-to-end power efficiency of 67.5% at 1 W.

Peking University (PKU) and China Institute of Atomic Energy (CIAE) are jointly proposing to construct a large science facility, temporarily called “Beijing ISOL”. This facility aims at both basic science and application goals, and is based on the double driver system, namely reactor driving and intense deuteron-beam driving. On the basic science side, the radioactive ion beams produced from the isotope separation online (ISOL) device will be used to study the new physics and technologies at the limit of nuclear stability. On the other side regarding to the applications, the facility will be devoted to material research for the nuclear energy system by using typically the intense neutron and ion beams. In the whole process of design, construction and operation, an opening policy will be pursued, and the domestic and international cooperation will be emphasized. Through this project, a joint research and education mode will be established.

This paper reports a comprehensive investigation of structural damage in yttria-stabilized zirconia irradiated with different ions over a wide fluence range. A similar multistep damage accumulation exists for the irradiations of different ions, but the critical doses for occurrence of second damage step, characterized by a faster increase in damage fraction, and the maximum elastic strain at the first damage step are varied and depend on ion mass. For irradiations of heavier ions, the second damage step occurs at a higher dose with a lower critical elastic strain. Furthermore, larger extended defects were observed in the irradiations of heavy ions at the second damage step. Associated with other experiment results and multistep damage accumulation model, the distinct discrepancies in the damage buildup under irradiations of different ions were interpreted by the effects of electronic excitation, energy of primary knock-on atom and chemistry contributions of deposited ions.

Irradiation-induced microstructure evolution and phase transformation have been studied on the nanocrystalline tungsten film with simple cubic structure (β phase). The samples were irradiated by 4 MeV Au ions at different fluences ranging from 6 × 1014 to 1 × 1016 ions/cm2, corresponding to the peak damage levels from 6 to 100 dpa (displacements per atom). Analysis by GIXRD and TEM reveals that the structure of tungsten film undergoes a distinct transition from simple cubic phase to bcc phase when the fluence is above 3 × 1015 ions/cm2 (30 dpa) and grain growth occurs with the increasing fluence. Radiation-induced small voids are clearly observed in the interior of coarsened grains at the highest fluence, 1 × 1016 ions/cm2 (100 dpa).

Magnetron sputtered ZrO2/W multilayer samples with each layer thickness of 5 nm and 50 nm are irradiated by 70keV He+ ions at fluences from 8× 1016to 6× 1017m 2at room temperature. The surface morphology and microstructural evolution are studied with scanning electron microscopy(SEM), X-ray diffraction(XRD) and cross-sectional transmission electron microscopy(TEM). The experimental results suggest that the radiation tolerance of the nano-multilayers consisting of same compounds can be different because of different interfacial structure and gr ain boundary.

A new cyathane diterpene, named as cyathin I (1), as well as two known cyathane diterpenes (12R)-11a,14a-epoxy-13a,14b,15-trihydroxycyath-3-ene (2) and erinacine I (3), were isolated from the liquid culture of Cyathus hookeri Berk. Their structures were elucidated on the basis of extensive spectroscopic analysis. Compounds 1-3 showed inhibition against nitric oxide production in macrophages with an IC50 value of 15.5, 52.3, and 16.8 μM, respectively.

Several populations of memory T cells have been described that differ in their migration and function. In this study, we have identified a unique subset of memory T cells, which we have named recirculating memory T cells (TRCM). By exposing Kaede transgenic mouse skin to violet light, we tracked the fate of cutaneous T cells. One population of memory CD4+ T cells remained in the skin. A second population migrated from the skin into draining lymph nodes (LNs) in a CCR7-dependent manner. These migrating CD4+ T cells expressed a novel cell surface phenotype (CCR7int/+CD62LintCD69−CD103+/− E-selectin ligands+) that is distinct from memory T cell subsets described to date. Unlike memory T cell subsets that remain resident within tissues long-term, or that migrate either exclusively between lymphoid tissues or into peripheral nonlymphoid sites, CD4+ TRCM migrate from the skin into draining LNs. From the draining LNs, CD4+ TRCM reenter into the circulation, distal LNs, and sites of non-specific cutaneous inflammation. In addition, CD4+ TRCM upregulated CD40L and secreted IL-2 following polyclonal stimulation. Our results identify a novel subset of recirculating memory CD4+ T cells equipped to deliver help to both distal lymphoid and cutaneous tissues.

Studies of threading dislocations with Burgers vector of c+a have been carried out using synchrotron white beam X-ray topography. The nucleation and propagation of pairs of opposite sign threading c+a dislocations is observed. Overgrowth of inclusions by growth steps leads to lattice closure failure and the stresses associated with this can be relaxed by the nucleation of opposite sign pairs of dislocations with Burgers vector c+a. Once these dislocations are nucleated they propagate along the c-axis growth direction, or can be deflected onto the basal plane by overgrowth of macrosteps. For the c+a dislocations, partial deflection can occasionally occur, e.g. the a-component deflects onto basal plane while the c-component continuously propagates along the growth direction. One factor controlling the details of these deflection processes is suggested to be related to the ratio between the height of the overgrowing macrostep and that of the surface spiral hillock associated with the threading growth dislocations with c-component of Burgers vector.

This paper puts forward an inverter design method based on TMS320F2812A. For inverter part we adopt double closed loops control method, on the basis of the analysis of the inverter designed the controller parameters, and realized the digital control algorithm through TMS320F2812A. Introduce the design method of the hardware system, and give the flow chart of the software control. Finally simulate the double closed loops algorithm though MATLAB, and test whether the control algorithm is feasible.

Materials performance is central to the satisfactory operation of current and future nuclear energy systems due to the severe irradiation environment in reactors. Searching for structural materials with excellent irradiation tolerance is crucial for developing the next generation nuclear reactors. Here, we report the irradiation responses of a novel multi-component alloy system, high entropy alloy (HEA) AlxCoCrFeNi (x = 0.1, 0.75 and 1.5), focusing on their precipitation behavior. It is found that the single phase system, Al0.1CoCrFeNi, exhibits a great phase stability against ion irradiation. No precipitate is observed even at the highest fluence. In contrast, numerous coherent precipitates are present in both multi-phase HEAs. Based on the irradiation-induced/enhanced precipitation theory, the excellent structural stability against precipitation of Al0.1CoCrFeNi is attributed to the high configurational entropy and low atomic diffusion, which reduces the thermodynamic driving force and kinetically restrains the formation of precipitate, respectively. For the multiphase HEAs, the phase separations and formation of ordered phases reduce the system configurational entropy, resulting in the similar precipitation behavior with corresponding binary or ternary conventional alloys. This study demonstrates the structural stability of single-phase HEAs under irradiation and provides important implications for searching for HEAs with higher irradiation tolerance.

The haze pollution caused by high PM2.5 concentrations has become one of the major environmental issues restricting urban and regional sustainable development in China in recent years. Therefore, the diagnosis of the pollution sources of PM2.5 and its major components in a scientific and efficient way is of great significance both scientifically and theoretically. A rare heavy haze pollution event occurred in Shanghai and the surrounding Yangtze River Delta in early December, 2013, that the hourly PM2.5 concentration reached 640 μg x m(-3). In this study, we analyzed the three typical episodes that occurred in Shanghai during this period. The particulate matter source apportionment technology (PSAT) was applied to study the source contributions to PM2.5 and its major components. Results showed that NO3-(2.5) were mostly contributed by industrial boilers and kilns, transportation and power plants. Comparatively, most of the SO4(2-) 2.5 came from industry and transport sectors. During the three episodes including haze, foggy haze and transport, local emissions contributed 35.3%, 44.8%, 22.7%, while super-regional transport accounted for 42.0%, 41.1% and 59.8% to PM2.5, respectively. In the YRD modeling domain, fugitive dust, industrial processing, volatile source, industrial boilers and kilns and transport were the major contributors to high concentrations of PM2.5, with the average contributions of 25.1%, 14.9%, 15.8%, 13.7% and 15.9%, respectively. Results showed that the very heavy haze pollution is usually not caused by a single city, the regional joint pollution control is of great importance to relieve the pollution level.

T helper 17 (Th17) cells play an important role in multiple sclerosis (MS) and its animal model experimental autoimmune encephalomyelitis (EAE). Th17 cell differentiation from naïve T cells can be induced in vitro by the cytokines transforming growth factor β1 and interleukin-6. However, it remains unclear whether other regulatory factors control the differentiation of Th17 cells. Mesenchymal stem cells (MSCs) have emerged as a promising candidate for inhibiting Th17 cell differentiation and autoimmune diseases. Despite the fact that several molecules have been linked to the immunomodulatory function of MSCs, many other key MSC-secreted regulators that are involved in inhibiting Th17 cell polarization are ill-defined. In this study, we demonstrated that the intraperitoneal administration of skin-derived MSCs (S-MSCs) substantially ameliorated the development of EAE in mice. We found that the proinflammatory cytokine tumor necrosis factor (TNF)-α, a key mediator in the pathophysiology of MS and EAE, was capable of promoting Th17 cell differentiation. Moreover, under inflammatory conditions, we demonstrated that S-MSCs produced high amounts of soluble TNF receptor 1 (sTNFR1), which binds TNF-α and antagonizes its function. Knockdown of sTNFR1 in S-MSCs decreased their inhibitory effect on Th17 cell differentiation ex vivo and in vivo. Thus, our data identified sTNFR1 and its target TNF-α as critical regulators for Th17 cell differentiation, suggesting a previously unrecognized mechanism for MSC therapy in Th17-mediated autoimmune diseases. Significance This study showed that administration of skin-derived mesenchymal stem cells (S-MSCs) was able to alleviate the clinical score of experimental autoimmune encephalomyelitis by inhibiting the differentiation of T helper 17 (Th17) cells. Tumor necrosis factor (TNF)-α is a critical cytokine for promoting Th17 cell differentiation. It was discovered that activated S-MSCs produced high amount of soluble TNF receptor 1 (sTNFR1), which neutralized TNF-α and inhibited Th17 cell polarization. The data identified S-MSC-secreted sTNFR1 and its target TNF-α as essential regulators for Th17 cell differentiation and revealed a novel mechanism underlying MSC-mediated immunomodulatory function in autoimmunity.

The thermal conductive composites prepared by twin-screw extrusion extrudes polypropylene and graphite.This paper studies the influence of molding process on the thermal conductivity.The experimental results show that thermal conductivity of composites changes with the screw rotate speed changing,obtaining the maximum when the screw rotate speed is 300r/min.Results indicate that the opposite trend with thermal conductivity and the melt index and injection speed,and the injection temperature has not a big influence on the thermal conductivity. The crystallization influences the electrical conductivity and density of some points of molding samples.In addition,the test condition has cast impact on thermal conductivity,in the lower temperature(lower than the Debye temperature),the thermal conductivity of composites increased with the of temperature and humidity increasing.

This paper presented coal consumption of electricity generation in Qingdao, Shandong Province, under different energy scenarios with LEAP 2010. And, time-serial emission inventory of As was also built based on fuel consumptions. The results show that the coal consumption will increase by 3.5 times ,amounting to 4.92 million tces under BAU scenario. The total emission of As is 2.7 Mtces with an average annual growth rate of 6.6%.

The threshold displacement energies in silicon carbide under different pressures are determined with ab initio molecular dynamics. The results show that the threshold displacement energies change anisotropically in different crystallographic directions when high pressure is applied. However, the weighted average values for both the C and Si sublattice, which determine the defect production in a material under irradiation, are found to increase significantly with increasing external pressures. Besides, we have observed some new defect structures under high pressures which are not observed at ambient conditions. Our results show that irradiation under high pressures could decrease the production rate of point defects in SiC, thus greatly enhancing its resistivity against radiation damage. The combination of irradiation and high pressure technique hence provides a pathway to obtain new structure materials.

The determination of stopping powers for slow heavy ions in targets containing light elements is important to accurately describe ion–solid interactions, evaluate ion irradiation effects and predict ion ranges for device fabrication and nuclear applications. Recently, discrepancies of up to 40% between the experimental results and SRIM (Stopping and Range of Ions in Matter) predictions of ion ranges for heavy ions with medium and low energies (

This work reports a greatly enhanced tolerance for He irradiation-induced swelling in nanocrystalline zirconia film with interconnected nanoporous structure (hereinafter referred as to NC-C). Compared to bulk yttria-stabilized zirconia (YSZ) and another nanocrystalline zirconia film only with discrete nano voids (hereinafter referred as to NC-V), the NC-C film reveals good tolerance for irradiation of high-fluence He. No appreciable surface blistering can be found even at the highest fluence of 6 × 10 17 cm −2 in NC-C film. From TEM analysis of as-irradiated samples, the enhanced tolerance for volume swelling in NC-C film is attributed to the enhanced diffusion mechanism of deposited He via widely distributed nano channels. Furthermore, the growth of grain size is quite small for both nanocrystalline zirconia films after irradiation, which is ascribed to the decreasing of area of grain boundary due to loose structure and low energy of primary knock-on atoms for He ions.

Using first-principles molecular dynamics (MD) and classical MD simulations, we investigate the minimum energy required for various incident ions to displace a carbon atom in single-walled carbon nanotubes (CNTs), which is a key parameter to characterize the damage capability of the incident ion. The role of chemical aspects of incident ions played in the damage production mechanism was analyzed in details. The results indicate that the chemical bonding properties of impinging ions could greatly lower the threshold displacement energy of carbon atoms in CNTs, and thus considerably enhance their damage capabilities compared to those chemically inactive ions. The strong chemical interactions existing between ions and nanotubes can considerably increase the amount of damages, which is in contrast with the conventional conclusion that the damage yield increases monotonically with the atomic number of incident ion owing to its dependence on the cross section of defect production. This chemical bonding assisted damage process is clearly different from the damage process resulted only from physical collisions.

Synchrotron White Beam X-ray Topography (SWBXT) imaging of wafers cut parallel to the growth axis from 4H-SiC boules grown using Physical Vapor Transport has enabled visualization of the evolution of the defect microstructure. Here we present observations of the propagation and post-growth mutual interaction of threading growth dislocations with c-component of Burgers vector. Detailed contrast extinction studies reveal the presence of two types of such dislocations: pure c-axis screw dislocations and those with Burgers Vector n1c+n2a, where n1is equal to 1 and n2is equal to 1 or 2. In addition, observations of dislocation propagation show that some of the threading dislocations with c-component of Burgers adopt a curved, slightly helical morphology which can drive the dislocations from adjacent nucleation sites together enabling them to respond to the inter-dislocation forces and react. Since all of the dislocations exhibiting such helical configurations have significant screw component, and in view of the fact that such dislocations are typically not observed to glide, it is believed that such morphologies result in large part from the interaction of a non-equilibrium concentration of vacancies with the originally approximately straight dislocation cores during post-growth cooling. Such interactions can lead to complete or partial Burgers vector annihilation. Among the reactions observed are: (a) the reaction between opposite-sign threading screw dislocations with Burgers vectors c and –c wherein some segments annihilate leaving others in the form of trails of stranded loops comprising closed dislocation dipoles; (b) the reaction between threading dislocations with Burgers vectors of -c+a and c+a wherein the opposite c-components annihilate leaving behind the two a-components; (c) the similar reaction between threading dislocations with Burgers vectors of -c and c+a leaving behind the a-component.

A review is presented of Synchrotron White Beam X-ray Topography (SWBXT) studies of stacking faults observed in PVT-Grown 4H-SiC crystals. A detailed analysis of various interesting phenomena were performed and one such observation is the deflection of threading dislocations with Burgers vector c/c+a onto the basal plane and associated stacking faults. Based on the model involving macrostep overgrowth of surface outcrops of threading dislocations, SWBXT image contrast studies of these stacking faults on different reflections and comparison with calculated phase shits for postulated fault vectors, has revealed faults to be of basically four types: (a) Frank faults; (b) Shockley faults; (c) Combined Shockley + Frank faults with fault vector s+c/2; (d) Combined Shockley + Frank faults with fault vector s+c/4.

In this paper, we report on the synchrotron white beam topographic (SWBXT) observation of “hopping” Frank-Read sources in 4H-SiC. A detailed mechanism for this process is presented which involves threading edge dislocations experiencing a double deflection process involving overgrowth by a macrostep (MP) followed by impingement of that macrostep against a step moving in the opposite direction. These processes enable the single-ended Frank-Read sources created by the pinning of the deflected basal plane dislocation segments at the less mobile threading edge dislocation segments to “hop” from one slip plane to other parallel slip planes. We also report on the nucleation of 1/3< >{ } prismatic dislocation half-loops at the hollow cores of micropipes and their glide under thermal shear stress.

The mtDNA 1555AG mutation was considered to be one of the most common causes of aminoglycoside-induced and non-syndromic hearing loss. However, this mutation was always found in homoplasmy with high phenotypic heterogeneity. Recently this mutation in heteroplasmy has been reported in several studies. In the present study, we have collected a large Chinese family harboring heteroplasmic mtDNA 1555AG mutation with diverse clinical phenotypes. To investigate the relationship between the mutation load and the severity of hearing loss under Eastern Asian background, we performed clinical, molecular, genetic and phylogenic analysis. This pedigree was characterized by coexistence of eight subjects with homoplasmic mutation and ten subjects with various degrees of heteroplasmy, and the results suggested that there was a strong correlation between the mutation load and the severity/age-onset of hearing loss (r=0.758, p0.001). We noticed that the mutation level of offspring was associated with their mothers' in this pedigree, which indicated that maybe exist a regular pattern during the process of the heteroplasmic transmission. In addition, analysis of the complete mtDNA genome of this family revealed that it belonged to Eastern Asian haplogroup B4C1. In addition, a rare homoplasmic mtDNA 9128TC variant was identified, it located at a strictly conserved site of mtDNA ATP6 gene.

In recent years, tapered glass capillary ion beam focusing is developing rapidly. It is attractive for simple, compact, low cost and easy use. However, the focusing mechanism for MeV ion beams is still indistinct. We present several experimental results of focusing 2 MeV He+ beam. Ion beams were focused by tapered glass capillaries with various outlet inner diameters from several micron to hundred micron. The current densities, angle divergences and energy spectra of the transmitted ion beams are measured. The results proved that 2 MeV He+ ions can focused and guided by our capillaries. The energy spectra show that a great part of transmitted ions experienced obvious energy loss, which is different from results of others research groups. We discussed the reason and charged it to the larger incident angle. Considered the incident ions with larger incident angle, the charge will distribute in a layer of micro meter depth in the capillary’s inner wall, but not the surface. The energy loss and many other spectra characters can be explained in this way.

The study presents an investigation of damage evolution of yttria-stabilized zirconia (YSZ) induced by irradiation of 100 keV He ions at room temperature as a function of fluence. Transmission electron microscopy (TEM), X-ray diffraction (XRD) and atomic force microscopy (AFM) were used in order to study the nature and evolution of structural damage at different levels. Our study shows that various kinds of defects are formed with the increasing fluence. Firstly, at low fluences, from 1 × 1016 to 4 × 1016 cm−2, of which maximum values of displacement per atom (dpa) range from 0.29 to 1.17, an elastic strain which is attributed to the accumulation of irradiation-induced discrete point defects, is presented. Secondly, in the intermediate fluences ranging from 8 × 1016 to 1 × 1017 cm−2 with corresponding dpa varying from 2.33 to 2.91, a large drop of elastic strain occurs accompanied by presence of an intensive damage region, which is comprised by large and interacted defect clusters. Thirdly, at the two high fluences of 2 × 1017 and 4 × 1017 cm−2, of which dpa are 5.83 and 11.65 respectively, a great amount of ribbon-like He bubbles with granular structure and cracks are presented at the depth of maximum concentration of deposited He atoms. The structural damage evolution and the mechanism of formation of He bubbles are discussed.

We present the enhanced wet etching of GaN epilayer implanted with Au+ ion. Patterned GaN with 2 microm-wide sink-like strips was achieved by using 500 keV Au+ ion implantation and KOH etching. The Dependence of etching depth on etching time for the implantation at different ion fluences was investigated. The experiment showed that the damaged GaN area could be almost etched out at high ion fluence, and the etching depth could exceed the project range of incident 500 keV Au+ ion. The etch pits could be observed at the bottom of the etched area. The -400 nm depth etching could be achieved with high fluence implantation after a long etching time, and the edge of etched area could remain clear until the etching process had passed 40 min. As-deposited SiO2 spheres were used to mask the GaN sample in implantation process to investigate the etching effect. -70 nm wave of the GaN surface was observed. The results of our experiments may suggest an approach to the fabricating of GaN devices.

Water quality criteria for aquatic environments are numerical concentrations or narrative statements to support and protect designated water uses, based on data quantifying the response of aquatic organisms to toxic pollutants in laboratory tests. In general, the main process being used around the world for establishing criteria for the protection of freshwater aquatic environment can be summarized as the following: (a) selecting the most sensitive species and testing toxicity to them and (b) application of evaluation methods to obtain the water quality criteria. The data requirement, tested organisms and three calculation methodologies were discussed in detail. In China, establishing appropriate and effective water quality criteria for protecting aquatic environment is an urgent task and national strategy. The systematic and feasible experience from other countries and international organizations can be a valuable guide for the Chinese Environmental Protection Departments. This review put forward researc...

Little information is available about the toxicity of toluene, ethylbenzene and xylene acting on macrophytes, and their toxicity data are rarely used in regulation and criteria decisions. The results extended the knowledge on toxic effects of toluene, ethylbenzene and xylene on aquatic plants. The responses of Hydrilla verticillata to these pollutants were investigated. Chlorophyll levels, lipid peroxidation, and antioxidant enzymes (superoxide dismutase and guaiacol peroxidase) showed diverse responses at different concentrations of toluene, ethylbenzene and xylene. The linear regression analyses were performed respectively, suggesting the concentrations of toluene, ethylbenzene and xylene expected to protect aquatic macrophytes were 7.30 mg L⁻¹, 1.15 mg L⁻¹ and 2.36 mg L⁻¹, respectively. This study emphasized that aquatic plants are also sensitive to organic pollutants as fishes and zooplanktons, indicating that macrophytes could be helpful in predicting the toxicity of these pollutants and should be considered in regulation and criteria decisions for aquatic environment protection.