Search

Most of the tidal flat shellfish harvesting equipment predominantly employed tracked or wheeled walking devices, which encountered issues such as significant sinking of the driving components during operation, poor load-carrying capacity of the devices, and high maintenance costs in the later stage. Therefore, this paper designed a tidal flat walking device based on the principle of spiral propulsion, which could be used for transportation, and conducted structural design and experimental research on the walking device. The impact of the spiral blade structure on working performance was analyzed by using DEMMBD(discrete element method-multibody dynamics) coupling simulation technology. A single-factor test was carried out to identify the optimal range for height, thickness, and helix angle of spiral blade on the walking mechanism. Subsequently, a three-factor and three-level orthogonal test method was then used to determine the optimal design parameters of blade. Finally, no-load and load operating performance tests were carried out on an experimental prototype, which was constructed according to similar criteria to evaluate the working performance of the designed running gear. The results indicated the following: 1) When all factors were independent, the slip rate of the walking device increased with higher helix angles. Both the traction force and working efficiency of the walking device initially increased and then decreased with higher helix angles. The slip rate of the walking device increased with the thickness increased, while working efficiency and traction coefficient of the walking device followed an initial increase and then decrease pattern. On the other hand, increasing the height-to-diameter ratio resulted in a decrease followed in slip rate of the walking device. The traction coefficient, increased overall with higher height-to-diameter ratios, with working efficiency exhibiting a similar trend. 2) The walking device demonstrated optimal driving performance with a helix angle of 25°, a height of 150 mm, and a thickness of 7.5 mm as determined by orthogonal test. 3) The slip rate of the walking device was 46.92% with no load, 63.56% with a 10 kg load, and 58.34% with a 15 kg load. The slip rate displayed an overall upward trend with increasing load. The subsidence amount was directly proportional to the load, with values of 47.59, 60.09, and 70.22 mm for no load, 10, and 15 kg load respectively, with a proportional coefficient of 1.512. 4) The rated load of the walking device was approximately 8 kg while the ultimate load was around 21.61 kg, which demonstrated its robust carrying capacity in the tidal flat environment. 5) In comparison with the simulation experiments, the deviation rates of subsidence and slip rate were 10.191% and 3.176% with no load, 3.744% and 3.571% with a 10 kg load, and 24.614% and 4.061% with a 15 kg load respectively. This affirmed that the simulation results could offer reference for prediction and analysis of walking device performance. These research findings were valuable for the development of more efficient tidal flat harvesting equipment with stronger carrying capacity. [ABSTRACT FROM AUTHOR]

Copyright of Experimental Technology & Management is the property of Experimental Technology & Management Editorial Office and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Experimental Technology & Management is the property of Experimental Technology & Management Editorial Office and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

A contact model can be expected to accurately and rapidly characterize the tidal flat soil using the discrete element method (DEM). In this study, the contact model was optimized using the API secondary development function of the discrete element simulation software (EDEM). The target model was selected as the Hertz-Mindlin contact model. Firstly, the plasticity and adhesion were added to the normal contact force. Secondly, the sliding friction force with the relative tangential velocity was input into the tangential contact force. Then, the moist elasto-plastic adhesion (MEPA) model was obtained. The maximum normal pressure and normal adhesion force of the piston pull-out test were selected as the indexes of virtual calibration. Plackett-Burman test showed that there were significant effects of the correction coefficient of sliding friction, Young 's modulus of soil, static friction coefficient between soil particles, rolling friction coefficient between particles, static friction coefficient between particles, and geometry on the maximum normal pressure of the probe. The maximum adhesion force of the probe depended mainly on the adhesion coefficient between particles and the geometry and their interaction. The piston pullout test showed that the combination of parameters was achieved in the comparison indexes for the virtual calibration of tidal flat soil under target working conditions, including the 0 h settling time, 0 min contact time, and 210 mm/min separation velocity. The virtual calibration of DEM parameters was realized using non-significant and significant parameters. Among them, the non-significant parameters were referred to the existing data, while the significant parameters were continuously adjusted to make the simulated curve of piston pull-out force close to the actual. The MEPA, JKR, EEPA, and Bonding models were compared to characterize the tidal flat soil. The shoveling test platform was then built to verify the accuracy of the models. The tidal flat soil with a thickness of 11 cm was accumulated in the soil box. The digging shovel had a cutting depth of 5cm in the soil box. Two tests were set firstly, where the angle of the digging shovel was adjusted to 25° and 30°, respectively, and the forward speed was 0.08m/s. Then one test was that the digging shovel angle of 20°, and the forward speed of 0.16 m/s. The force was accurately obtained at the sensor of the shoveling device. The EDEM and the multi-dynamics (RecurDyn) software were also selected to simulate the shoveling. The test results showed that the average absolute error of the MEPA model was controlled within 50 N, compared with the actual shoveling resistance. The simulation accuracies of the MEPA model were about 65.957 %, 74.206%, and 59.326 % higher than those of the JKR, EEPA, and the Bonding model, respectively. Compared with the field test, the relative errors of the MEPA model were 5.598% and 6.362% in the soil accumulation thickness and side margins, respectively. Both errors were remained within 10%. Therefore, the MEPA model can be used to better simulate the tidal flat soil. It is of great significance to simulate and optimize the tidal flat device. [ABSTRACT FROM AUTHOR]

This study aims to determine the rheological properties and structural stability of the beach soil for shellfish cultivation. A series of rheological tests were carried out on the beach soil with different water content and standing time using a rotary rheometer. A single-factor test was also conducted to explore the influence of water content and standing time on the rheological properties of the beach soil. The soil shear was then analyzed to determine the influence of water content and standing time on yield stress. At the same time, the numerical model was established for the yield stress, water content and resting time after the central composite design (CCD) test in the response surface method (RSM). A comparison was then made on the influence of water content and resting time on yield stress. Finally, the reliability and accuracy of the regression model were further verified to compare the error between the measured and the actual values. The results show as follows: 1) The shear stress gradually decreased with the increase of water content under the same shearing rate in the shearing process, whereas there was a gradual increase with the increase of standing time; In addition, the beach soil was characterized by the consolidation. The longer the static time was, the longer the solid-liquid transformation was, and the later the solid-liquid node was. The static time shared the greatest impact on the solid-liquid node in the early stage. The longer the static time was, the smaller the impact on the solid-liquid node was. 2) When the average shear stress and yield stress were at the shear rate of 10 - 60 s-1 under the same standing time, the overall shear stress of the tidal flat soil gradually decreased with the increase of water content, thus reducing the structural stability of the tidal flat soil. In addition, the overall shear stress of the tidal flat soil gradually increased under the same moisture content with the increase of static time, indicating the increase in the structural stability of tidal flat soil. The change rate of yield stress with the static time showed that there was a cut-off point of moisture content in the beach soil, which was between 64.5% and 67.0%. In the samples exceeding this moisture content cut-off point, the change rate of yield stress with the static time remained stable after the static time exceeded 31 h, where there was no fluctuation in the yield stress. The yield stress ranged from 2 240 to 4 380 Pa. In addition, the yield stress in the sample of 62.0%-69.5% was between the 0-53 h, and the yield stress between 62.0%-69.5% was between 1 870-5 410 Pa. 3) The P and R 2 values of numerical models were above 0.05, and 0.953 4, respectively, indicating the high reliability and accuracy. There was a more significant influence of water content on the yield stress, compared with the resting time. However, the interaction between water content and resting time shared no significant influence on the yield stress. The test verified that the measured yield stress was basically consistent with the predicted one, with an error of less than 15.0%. The rheological properties of beach soil can be better characterized as well. The findings can provide a strong reference for the research and optimization of beach shellfish harvesting machinery [ABSTRACT FROM AUTHOR]

Branch and leaf pruning has been one of the most important links in the process of tomato planting for reducing the disease rate and increasing economic benefits. However, the manual pruning of tomato branches and leaves cannot fully meet large-scale production in recent years, due to the time-consuming and labor-intensive task. An accurate and rapid identification of the pruning position can be greatly contributed to the automatic operation of tomato branch and leaf pruning. In this study, a Recognition method was proposed for the pruning point of the tomato lateral branch using an improved Mask R-CNN. Firstly, the backbone network of ResNet50 in the original Mask R-CNN was replaced with the MobileNetv3-Large to reduce the model complexity. Efficient Channel Attention was added to the feature map C3 and C4, in order to focus more on the features of the lateral and main branch rather than other features. Then, the tomato lateral and main branches were predicted using the improved Mask R-CNN. Three steps were selected to avoid some single branches taken as multiple masks. The lateral and main branch masks were first distinguished by the aspect ratio of the bounding boxes. The overlap and pole constraints were then analyzed for the adjacent masks that belonged to the same branch. The masks with similar constraints were finally merged and joined in the images. The pruning point of the lateral branch was only positioned at one of the two ends of the lateral branch. The lateral pruning point identification was proposed with the help of the main branch, in order to determine the coordinate of the lateral pruning point. The range near the main branch was first determined. And then the branch pruning end was determined by estimating which one of the lateral branch left and right endpoints was in the range. The center point close to the endpoint of the pruning end was finally determined as the pruning point of the lateral branch. The original and improved Mask R-CNN were also compared to verify the detection performance of the lateral and main branches. The recall rate and precision of the original Mask R-CNN were 87.9% and 93.3%, respectively, whereas, the recall rate and precision of the improved Mask R-CNN were 91.2% and 88.6%, respectively. The number of backbone network parameters in the improved Mask R-CNN was only 21.1% of that in the original one. The average segmentation time of the improved Mask R-CNN decreased by 0.038 s than before. The results showed that the backbone network of MobileNetv3-Large reduced the model parameters with the high speed in the improved Mask R-CNN. More branches were recognized, particularly when adding the Efficient Channel Attention mechanism into the feature map C3 and C4. Lateral and main branches that were divided into multiple masks were selected randomly to verify the performance of merging masks. The merging success rate of lateral branch masks was lower than that of the main branch masks, due to the more outstanding curved shape of the lateral branch. The average success rate of merging masks was 86.2%, indicating the excellent performance of merging masks. The presence of multiple pruning points was effectively reduced, where the single branch was normally taken as the multiple masks. Some images were selected randomly in the test set to verify the recognition accuracy for the pruning point of the lateral branch. The result showed that the recognition success rate on sunny days was higher than that on cloudy. The average recognition success rate was 82.9%, which fully met the requirements of lateral branch pruning. This finding can provide the technical support for the tomato branch and leaf pruning automatically. [ABSTRACT FROM AUTHOR]

Tea sorting has been one of the most important links in tea production. Manual sorting has been often adopted to remove the excess impurities (such as branches and grains) from the collected fresh tea in traditional processing. However, the current sorting cannot fully meet the high requirement of taste and quality in the finished tea products after collection in recent years, due to the labor-intensive and high cost. Fortunately, machine vision has been gradually applied to tea impurity sorting, particularly for fully automatic sorting in the process of tea collection. Among them, the single-stage lightweight network (represented by YOLOv5 deep learning) can perform better performance for small targets with high detection speed and accuracy. However, the conventional YOLOv5 network cannot be used to extract the characteristics of tea impurities, due to the disorderly clusters, the generally small targets, the complex types of impurities, and the similar color to the tea. Particularly, the overlapping small targets can cause an inaccurate prediction box, leading to low accuracy or miss detection of the tea impurities. It is necessary to improve the conventional YOLOv5 network to meet the requirements of tea impurity detection. In this study, an improved YOLOv5 model was proposed to detect the tea impurity with a higher accuracy and detection speed than before. The YOLOv5 was taken as the baseline network. The K-Means clustering was applied to cluster the real boxes of impurities as the anchor frame size suitable for the characteristics of tea impurities. Convolutional Block Attention Module (CBAM) was introduced into the backbone feature extraction network (CSPDarkNet). The key features were obtained using the channel and spatial dimension of feature images. A Spatial Pyramid Pooling (SPP) module was added to the neck network, in order to integrate and extract the multi-scale features of different sensory fields. The deep separable convolution was updated to reduce the number of network parameters for the higher detection speed. The confidence loss weight of the small target prediction in the feature map was improved for the higher detection accuracy of the network for the small targets. The data set was taken as the Tieguanyin tea mixed with the rice, melon seed shell, bamboo branches, and tea stems. The results show that the improved YOLOv5 presented a higher confidence score than the conventional one, where the positioning was much more accurate without missing detection. The mAP and FPS of improved YOLOv5 reached 96.05% and 62 frames/s, respectively. The higher efficiency and robustness of the improved model were achieved to compare the mainstream target detections. The findings can provide a strong reference for the detection accuracy and speed of small target impurities in the tea production process. [ABSTRACT FROM AUTHOR]

Image Jacobian matrix is core portion of robot vision servo system. During estimating image Jacobian matrix with traditional methodology of KF (Kalman Filter) and UKF (Unscented Kalman Filter), the system noises of unknown statistical properties is determined according to priori knowledge, which is remained unchanged in system. However, this methodology of dealing system noises would make image Jacobian matrix’s estimation inaccuracy because of time-varying system noises. Based on traditional methodology of KF and UKF, in this paper, we structured propagator of system noises estimation with the difference value of system state predicted value and updated value, and raised Adoption Unscented Kalman Filter to estimate image Jacobian matrix. Two points on the tomato string’s stem, clamping point and picking point, were chosen as feature points in the image feature space. The center of mass of fruit stem was extracted as the holding point. According to the vertical growth characteristics of tomato clusters and the distance between the holding point on the end and the cutting point on the image, a point above the holding point was extracted as the cutting point. Image Jacobian matrix was used to transform information of pixel difference in image feature space to change in pose of end-effector in manipulator motion space. First, results of image feature space localization experiment showed that six image feature errors were smaller and the average image feature error of visual servo system based on AUKF was 4.978 pixes/mm in condition of unknown system noises. Compared with visual servo system based on KF and UKF, average image feature error reduced 54.44% and 24.78%, respectively. Second, three dimensional space positioning experiment between end-effector and target picking point showed that the final distance between end-effector and target picking point was 4.19 mm, reduced by 79.74% and 80.38% compared to methods of KF and UKF. Third, the response time of visual servo control system based on KF method, UKF method and AUKF method to estimate image Jacobian matrix was 2, 1.5 and 1.2 s, respectively. The picking experiment was carried out on the visual servo test platform of the seven-degree-of-freedom picking manipulator. The visual system based on each visual servo control method was tested for 30 times. For the visual servo system based on AUKF method estimation, the success rate of picking the static target was 90%, and the success rate of picking the dynamic target was 83%. Compared with KF methodology and UKF methodology, the success rate of static picking test was increased by 17 and 10 percentage points, respectively, and the success rate of dynamic picking test was increased by 16 and 10 percentage points, respectively. The results showed that the static picking time based on AUKF methodology was the 18 s, compared with the visual servo system based on KF methodology and UKF methodology, the time of static picking was reduced by 35.71% and 25%, respectively. The average dynamic picking time of visual servo system based on AUKF was 22 s and the test time of dynamic picking was reduced by 35.29% and 26.67%, respectively compared with the visual servo system based on KF methodology and UKF methodology. The image Jacobian matrix based on AUKF was suitable for the dynamic picking of tomato clusters, and the accuracy of visual servo control under dynamic condition was lower than that under static condition. Test results suggested that the proposed AUKF method with KF method and the UKF method compared to estimating by image Jacobin matrix, and AUKF method to estimate the image Jacobin matrix, reduced the process of picking robot visual servo control system noise interference, which made the picking robot visual servo control system of processing noise adapted to the change of the visual servo system, resulting in higher positioning precision for picking robot visual servo control system . [ABSTRACT FROM AUTHOR]

Automatic harvesting of fruits and vegetables is a key process to realize the automation and intellectualization of agricultural production, which can reduce production costs and improve the production efficiency. Tomato is one of the most fruits and vegetables planted in China. The researches on tomato harvesting robots are focused on the single fruit harvesting. The end-effector of the harvesting robot touches the tomato fruit directly and picks one tomato once during harvesting, so the tomato fruits are easy to be damaged and the harvesting efficiency is very low. To overcome the above shortages of the single fruit harvesting, the method of the tomato cluster picking was presented, and the determination method of picking point was developed based on the corner detection on the tomato stem skeleton for the binocular vision system of the tomato cluster picking robot in the paper. The test platform of the vision system was set up and the experiments on the determination of the picking points have been conducted. In the paper, the color images of the tomato clusters were collected in greenhouse in the agricultural production base. The target tomato cluster was segmented from background by OTSU method according to the color features of the tomato clusters and denoised by the morphologic method and threshold method. The centroid of tomato fruit cluster was obtained by enclosing rectangle method. Furthermore, the rectangle region of interest of the target stem was recognized according to constraint relationship between the fruit cluster and the fruit stem, which included the whole stem of the target tomato cluster. Converting the RGB (red, green, blue) color channel map to the HSV (hue, saturation, value) channel map, there are different grayscales between the stem and the background. The target stem of the tomato cluster was separated from background by using the gray difference of H channel and denoised by morphologic method, median filtering method and extracting the maximum connected region. To avoid the effects of the irregular stem on the picking point determination, we abstracted the stem skeletons by Zhang’s thinning algorithm to simplify the stem original shape and extract the kernel information of the stem, and then, the Harris algorithm was applied to extract the corner points of the skeleton, and the corner points were sorted from large to small according to the vertical axis coordinates. The picking feature points on the target stem were obtained by averaging pixel coordinates of the 5 corner points. Sixty groups of experiments on the determination of picking points of the tomato cluster were carried out on the binocular vision test platform. The results show that the success rate of position information obtaining of the picking point on the stem is 90%. Comparing X and Y coordinates data of the picking point and centroid of the tomato fruit clusters, the X coordinates of the picking feature points vary in small range, while Y coordinates vary within wide limits, which results from the main stem growing in longitudinal direction. The mean absolute value of the pixel deviation of the Y coordinates is 21. The research provides the basis for locating the picking point on the stem for the tomato fruit cluster picking robots. [ABSTRACT FROM AUTHOR]

Copyright of Transactions of the Chinese Society of Agricultural Engineering is the property of Chinese Society of Agricultural Engineering and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The seeds cannot fully sprout owing to the seed quality and environmental differences. So it is difficult to provide seedling pots without empty seedling holes for automatic transplanting. In order to reduce the number of seedling shortage and the manual labor intensity of seedling supplement, and to improve transplanting quality, a method for supplementing seedlings in cotyledon phase was presented in the paper. According to the delicate seedling, undeveloped root system and the unconsolidated substrate in pot, a new type of end-effector for supplementing pot-seedling in cotyledon phase with 4 seedling shovels was designed. The 4 angular seedling shovels were synchronously driven up and down by stepper motor moving the X-shaped press rod. They can shape enveloping surface when they are inserted into the lower limit position of the whole pot and surrounded the seedlings from the 4 sides of seedling substrates during seedling. And then the pot seedling was taken out from seedling hole and transplanted to the target hole. The seedling supplementing was finished while the pot seedling was left in the target pot hole and the seedling spades lifted it up along the inclined guide. The 3 factor and 3 level orthogonal tests were conducted respectively with the Zheza809 tomato pot seedlings in cotyledon phase with the seedling age of 16, 21 and 26 d cultivated in standard seedling tray with 72 holes. In the test, the velocities of inserting and taking out of matrix for the shovels were measured by speedtro-50 laser velometer, and the average velocities were 29.85 and 31.12 m/s respectively. The mixture ratio of peat, vermiculite and perlite in nursery matrix, the moisture content of the substrate and the seedling age were chosen as factors. The matrix net rate, which is the percentage of the weight of pot seedling taken out from the pot holes by the end-effector in the total mass of the pot seedling in the pot hole, was set as index. The results indicate that the net rate of taking out the free substrate without seedlings or the pot seedlings in cotyledon phase is affected significantly by the pot seedling age and the mixture ratio of peat, vermiculite and perlite in nursery matrix. The net rate increases with the seedling age, which reaches the highest value at the end of cotyledon phase and the mixture ratio of peat, vermiculite and perlite in nursery matrix of 2:2:1. The effect of matrix water content from 67.1% to 79.2% on the net rate is not significant, while the net rate keeps a high value owing to good cohesive force and plasticity of the substrate when the moisture content of the substrate is 74.1%. When the growth age is 26 d, the mixture ratio of peat, vermiculite and perlite in nursery matrix is 2:2:1 and the moisture content of the substrate is 74.1%, the average net rate reaches the maximum of 89.5% and the shape and volume of the seedling pot keep complete. To further verify the optimal combination obtained by the test, the experiments of seedling taking out and supplementing were carried out with tomato pot seedlings with the age of 26 d, the mixture ratio of peat, vermiculite and perlite in nursery matrix of 2:2:1 and suitable substrate moisture content. The results show that the success rates for the free substrate without seedlings and pot seedlings are both 100%, which can take out the pot seedlings in cotyledon phase with crisp plant and loose matrix as a whole and fill them into target hole on the seedling pot completely. [ABSTRACT FROM AUTHOR]