Search

KTiOPO4 (KTP) nanoparticles (NPs) are potential materials as biolabels for long-term imaging. Optimizing their properties can lead to higher imaging efficiency and lower cytotoxicity and side effects. In this study, these nanoparticles were synthesized using the co-precipitation method and capping agents of oxalic acid and glycine. The capping agent's effect on the structural, optical, morphological, hemocompatibility, and biocompatibility properties of the obtained nanoparticles was studied. The smallest (12.56 nm) grain size and the lowest lattice strain (0.0024) were obtained using 1:1 and 1:3 mol ratios of glycine, respectively. Oxalic acid as a capping agent resulted in needle-type, flower-type, and oval-form NPs. Polygonal tablet form, cubic, and polyhedral forms of KTP NPs were synthesized using glycine. C–O–H bending bonds, O–H, N–H, and carbonyl (C=O) stretching bonds remain on the surface of synthesized NPs after heat treatment and functionalization of their surface. Our results showed that the surface functionalization modifies the biocompatibility properties of NPs. The 1:3 mol ratio of oxalic acid as a capping agent resulted in the perfect KTP NPs for long-term imaging studies. The presence of hydroxyl groups improved the biocompatibility of obtained KTP NPs using a 1:3 mol ratio of oxalic acid over time. The needle form of obtained NPs resulted in an increase in cell cytotoxicity at higher concentrations.

Microbial Fuel Cells (MFCs) represent an environmentally-friendly approach to generating electricity, but the need to study variation parameters to find improvement conditions has been an important challenge for decades. In this study, a single-chamber MFC was designed to investigate the key parameters such as the concentration and type of bacteria, chamber temperature, electrode spacing, and substrate rotation speed that affected the performance of MFCs. Therefore, two types of bacteria, Shewanella oneidensis (S.one) and Escherichia coli (E. coli), were compared as microorganisms. Then, the function of MFC was investigated under the following condition: three temperatures (30 ℃, 45℃, and 60℃), three bacterial concentrations (0.5% (v/v) (4.5 mg/ml), 1% (v/v) (9mg/ml), and 1.5% (v/v) (13.5mg/ml)), electrode distances (2 cm, 3 cm, 4cm), and substrate speeds (100 rpm, 150 rpm, 200 rpm). Ultimately, (S.one) bacteria, a chamber temperature of 45 ℃, a bacterial concentration of 1% (v/v) (9mg/ml), a cathode-anode spacing of 3 cm, and a rotation speed of 150 rpm proved to be the most efficient parameter settings for the constructed microbial fuel cell. The maximum voltage and highest power density were 486.9 mV and 9.73 mW/ , respectively, with a resistance of 7500 ohms. These results are meaningful for determining and improving important parameters in an MFC device.

Tissue-engineered bone substitutes, characterized by favorable physicochemical, mechanical, and biological properties, present a promising alternative for addressing bone defects. In this study, we employed an innovative 3D host-guest scaffold model, where the host component served as a mechanical support, while the guest component facilitated osteogenic effects. More specifically, we fabricated a triangular porous polycaprolactone framework (host) using advanced 3D printing techniques, and subsequently filled the framework's pores with tragacanth gum-45S5 bioactive glass as the guest component. Comprehensive assessments were conducted to evaluate the physical, mechanical, and biological properties of the designed scaffolds. Remarkably, successful integration of the guest component within the framework was achieved, resulting in enhanced bioactivity and increased strength. Our findings demonstrated that the scaffolds exhibited ion release (Si, Ca, and P), surface apatite formation, and biodegradation. Additionally, in vitro cell culture assays revealed that the scaffolds demonstrated significant improvements in cell viability, proliferation, and attachment. Significantly, the multi-compartment scaffolds exhibited remarkable osteogenic properties, indicated by a substantial increase in the expression of osteopontin, osteocalcin, and matrix deposition. Based on our results, the framework provided robust mechanical support during the new bone formation process, while the guest component matrix created a conducive micro-environment for cellular adhesion, osteogenic functionality, and matrix production. These multi-compartment scaffolds hold great potential as a viable alternative to autografts and offer promising clinical applications for bone defect repair in the future.

Abstract Background Three-dimensional (3D) printing is a capable approach for the fabrication of bone tissue scaffolds. Nevertheless, a purely made scaffold such as polylactic acid (PLA) may suffer from shortcomings and be restricted due to its biological behavior. Gelatin, hydroxyapatite and platelet-rich plasma (PRP) have been revealed to be of potential to enhance the osteogenic effect. In this study, it was tried to improve the properties of 3D-printed PLA scaffolds by infilling them with gelatin-nano-hydroxyapatite (PLA/G-nHA) and subsequent coating with PRP. For comparison, bare PLA and PLA/G-nHA scaffolds were also fabricated. The printing accuracy, the scaffold structural characterizations, mechanical properties, degradability behavior, cell adhesion, mineralization, systemic effect of the scaffolds on the liver enzymes, osteocalcin level in blood serum and in vivo bone regeneration capability in rat critical-sized calvaria defect were evaluated. Results High printing accuracy (printing error of

Abstract In this paper, the in-vivo healing of critical-sized bony defects by cell-free and stem cell-seeded 3D-printed PLA scaffolds was studied in rat calvaria bone. The scaffolds were implanted in the provided defect sites and histological analysis was conducted after 8 and 12 weeks. The results showed that both cell-free and stem cell-seeded scaffolds exhibited superb healing compared with the empty defect controls, and new bone and connective tissues were formed in the healing site after 8 and 12 weeks, postoperatively. The higher filled area, bone formation and bone maturation were observed after 12 weeks, particularly for PLA + Cell scaffolds.

Introduction: Alumina-titanium (Al2O3-Ti) composites with enhanced mechanical and corrosion properties have been recently developed for potential applications in orthopaedics and hard tissue replacements. However, before any clinical use, their interactions with biological environment must be examined. Methods: The aim of this study, therefore, was to assess the biocompatibility of three Al2O3-Ti composites having 25, 50, and 75 volume percentages of titanium. These materials were made by spark plasma sintering (SPS), and MC3T3-E1 cells were cultured onto the sample discs to evaluate the cell viability, proliferation, differentiation, mineralization, and adhesion. Furthermore, the apatite formation ability and wettability of the composites were analysed. Pure Ti (100Ti) and monolithic Al2O3 (0Ti) were also fabricated by SPS and biological characteristics of the composites were compared with them. Results: The results showed that cell viability to 75Ti (95.0%), 50Ti (87.3%), and 25Ti (63.9%) was superior when compared with 100Ti (42.7%). Pure Al2O3 also caused very high cell viability (89.9%). Furthermore, high cell proliferation was seen at early stage for 50Ti, while the cells exposed to 75Ti proliferated more at late stages. Cell differentiation was approximately equal between different groups, and increased by time. Matrix mineralization was higher on the composite surfaces rather than on 0Ti and 100Ti. Moreover, the cells adhered differently to the surfaces of different biomaterials where more spindle-shaped configuration was found on 100Ti, slightly enlarged cells with dendritic shape and early pseudopodia were observed on 75Ti, and more enlarged cells with long dendritic extensions were found on 0Ti, 25Ti, and 50Ti. The results of EDS analysis showed that both Ca and P deposited on the surfaces of all materials, after 20 days of immersion in SBF. Conclusion: Our in-vitro findings demonstrated that the 75Ti, 50Ti, and 25Ti composites have high potential to be used as load-bearing orthopedic materials.

Background: Coronavirus disease 2019 (COVID-19) has become one of the most serious diseases worldwide. The contagiousness of the virus and its unexpectedly rapid spread in different communities have raised many concerns. Objectives: This study investigated the association of clinical findings and hospital stay length of COVID-19 patients with diabetes and hypertension history in Garmsar Hospital. Methods: This cross-sectional study assessed COVID-19 patients admitted to Motamedi Hospital, Garmsar, Iran. Data were recorded in Minitab V17 software and analyzed through analysis of variance (ANOVA). Pearson's and Spearman's correlation coefficients were also computed for quantitative and qualitative variables, respectively. Results: The mean age was significantly higher in the group with underlying diseases than in the control group. The proportion of CRP-positive cases was higher in the hypertensive group than in the diabetes + hypertensive group, but it was not statistically significant. The rate of shortness of breath, length of hospital stay, and mortality were lower in the control group than in the group with underlying diseases, but this difference was not statistically significant. Conclusions: Although the incidence of respiratory distress, the length of hospital stay, and the mortality rate were lower in the control group than in the group with diabetes + hypertension, there was no significant association between these conditions and the risk of death and the length of hospital stay due to COVID-19. [ABSTRACT FROM AUTHOR]

Abstract Background Alumina-titanium (Al2O3-Ti) biocomposites have been recently developed with improved mechanical properties for use in heavily loaded orthopedic sites. Their biological performance, however, has not been investigated yet. Methods The aim of the present study was to evaluate the in vivo biological interaction of Al2O3-Ti. Spark plasma sintering (SPS) was used to fabricate Al2O3-Ti composites with 25 vol.%, 50 vol.%, and 75 vol.% Ti content. Pure alumina and titanium were also fabricated by the same procedure for comparison. The fabricated composite disks were cut into small bars and implanted into medullary canals of rat femurs. The histological analysis and scanning electron microscopy (SEM) observation were carried out to determine the bone formation ability of these materials and to evaluate the bone-implant interfaces. Results The histological observation showed the formation of osteoblast, osteocytes with lacuna, bone with lamellar structures, and blood vessels indicating that the healing and remodeling of the bone, and vasculature reconstruction occurred after 4 and 8 weeks of implantation. However, superior bone formation and maturation were obtained after 8 weeks. SEM images also showed stronger interfaces at week 8. There were differences between the composites in percentages of bone area (TB%) and the number of osteocytes. The 50Ti composite showed higher TB% at week 4, while 25Ti and 75Ti represented higher TB% at week 8. All the composites showed a higher number of osteocytes compared to 100Ti, particularly 75Ti. Conclusions The fabricated composites have the potential to be used in load-bearing orthopedic applications.

Abstract Advances in biomaterials and the need for patient-specific bone scaffolds require modern manufacturing approaches in addition to a design strategy. Hybrid materials such as those with functionally graded properties are highly needed in tissue replacement and repair. However, their constituents, proportions, sizes, configurations and their connection to each other are a challenge to manufacturing. On the other hand, various bone defect sizes and sites require a cost-effective readily adaptive manufacturing technique to provide components (scaffolds) matching with the anatomical shape of the bone defect. Additive manufacturing or three-dimensional (3D) printing is capable of fabricating functional physical components with or without porosity by depositing the materials layer-by-layer using 3D computer models. Therefore, it facilitates the production of advanced bone scaffolds with the feasibility of making changes to the model. This review paper first discusses the development of a computer-aided-design (CAD) approach for the manufacture of bone scaffolds, from the anatomical data acquisition to the final model. It also provides information on the optimization of scaffold’s internal architecture, advanced materials, and process parameters to achieve the best biomimetic performance. Furthermore, the review paper describes the advantages and limitations of 3D printing technologies applied to the production of bone tissue scaffolds.