Search

This paper outlines the development and operation of Yeti, a bottom-up traffic emission inventory framework written in the Python 3 scripting language. A generalized representation of traffic activity and emission data affords a high degree of scalability and flexibility in the use and execution of Yeti, while accommodating a wide range of details on topological, traffic, and meteorological data. The resulting traffic emission data are calculated at a road-level resolution on an hourly basis. Yeti is initially applied to traffic activity and fleet composition data provided by the senate administration for the city of Berlin, which serves as the region of interest, where the Yeti-calculated emissions are highly consistent with officially reported annual aggregate levels, broken down according to different exhaust and non-exhaust emission modes. Diurnal emission profiles on select road segments show not only the dependence on traffic activities but also on road type and meteorology. These road-level emissions are further classified on the basis of vehicle categories and Euro emission classes, and the results obtained confirmed the observations of the city of Berlin and subsequent rectifications.

The Berlin Air quality and Ecosystem Research: Local and long-range Impact of anthropogenic and Natural hydrocarbons (BAERLIN2014) campaign was conducted during the 3 summer months (June–August) of 2014. During this measurement campaign, both stationary and mobile measurements were undertaken to address complementary aims. This paper provides an overview of the stationary measurements and results that were focused on characterization of gaseous and particulate pollution, including source attribution, in the Berlin–Potsdam area, and quantification of the role of natural sources in determining levels of ozone and related gaseous pollutants. Results show that biogenic contributions to ozone and particulate matter are substantial. One indicator for ozone formation, the OH reactivity, showed a 31 % (0.82 ± 0.44 s−1) and 75 % (3.7 ± 0.90 s−1) contribution from biogenic non-methane volatile organic compounds (NMVOCs) for urban background (2.6 ± 0.68 s−1) and urban park (4.9 ± 1.0 s−1) location, respectively, emphasizing the importance of such locations as sources of biogenic NMVOCs in urban areas. A comparison to NMVOC measurements made in Berlin approximately 20 years earlier generally show lower levels today for anthropogenic NMVOCs. A substantial contribution of secondary organic and inorganic aerosol to PM10 concentrations was quantified. In addition to secondary aerosols, source apportionment analysis of the organic carbon fraction identified the contribution of biogenic (plant-based) particulate matter, as well as primary contributions from vehicles, with a larger contribution from diesel compared to gasoline vehicles, as well as a relatively small contribution from wood burning, linked to measured levoglucosan.

With NO2 limit values being frequently exceeded in European cities, complying with the European air quality regulations still poses a problem for many cities. Traffic is typically a major source of NOx emissions in urban areas. High-resolution chemistry transport modelling can help to assess the impact of high urban NOx emissions on air quality inside and outside of urban areas. However, many modelling studies report an underestimation of modelled NOx and NO2 compared with observations. Part of this model bias has been attributed to an underestimation of NOx emissions, particularly in urban areas. This is consistent with recent measurement studies quantifying underestimations of urban NOx emissions by current emission inventories, identifying the largest discrepancies when the contribution of traffic NOx emissions is high. This study applies a high-resolution chemistry transport model in combination with ambient measurements in order to assess the potential underestimation of traffic NOx emissions in a frequently used emission inventory. The emission inventory is based on officially reported values and the Berlin–Brandenburg area in Germany is used as a case study. The WRF-Chem model is used at a 3 km × 3 km horizontal resolution, simulating the whole year of 2014. The emission data are downscaled from an original resolution of ca. 7 km × 7 km to a resolution of 1 km × 1 km. An in-depth model evaluation including spectral decomposition of observed and modelled time series and error apportionment suggests that an underestimation in traffic emissions is likely one of the main causes of the bias in modelled NO2 concentrations in the urban background, where NO2 concentrations are underestimated by ca. 8 µg m−3 (−30 %) on average over the whole year. Furthermore, a diurnal cycle of the bias in modelled NO2 suggests that a more realistic treatment of the diurnal cycle of traffic emissions might be needed. Model problems in simulating the correct mixing in the urban planetary boundary layer probably play an important role in contributing to the model bias, particularly in summer. Also taking into account this and other possible sources of model bias, a correction factor for traffic NOx emissions of ca. 3 is estimated for weekday daytime traffic emissions in the core urban area, which corresponds to an overall underestimation of traffic NOx emissions in the core urban area of ca. 50 %. Sensitivity simulations for the months of January and July using the calculated correction factor show that the weekday model bias can be improved from −8.8 µg m−3 (−26 %) to −5.4 µg m−3 (−16 %) in January on average in the urban background, and −10.3 µg m−3 (−46 %) to −7.6 µg m−3 (−34 %) in July. In addition, the negative bias of weekday NO2 concentrations downwind of the city in the rural and suburban background can be reduced from −3.4 µg m−3 (−12 %) to −1.2 µg m−3 (−4 %) in January and from −3.0 µg m−3 (−22 %) to −1.9 µg m−3 (−14 %) in July. The results and their consistency with findings from other studies suggest that more research is needed in order to more accurately understand the spatial and temporal variability in real-world NOx emissions from traffic, and apply this understanding to the inventories used in high-resolution chemical transport models.

OBJECTIVES: To develop treat-to-target (T2T) recommendations in giant cell arteritis (GCA) and polymyalgia rheumatica (PMR). METHODS: A systematic literature review was conducted to retrieve data on treatment targets and outcomes in GCA/PMR as well as to identify the evidence for the effectiveness of a T2T-based management approach in these diseases. Based on evidence and expert opinion, the task force (29 participants from 10 countries consisting of physicians, a healthcare professional and a patient) developed recommendations, with consensus obtained through voting. The final level of agreement was provided anonymously. RESULTS: Five overarching principles and six-specific recommendations were formulated. Management of GCA and PMR should be based on shared decisions between patient and physician recognising the need for urgent treatment of GCA to avoid ischaemic complications, and it should aim at maximising health-related quality of life in both diseases. The treatment targets are achievement and maintenance of remission, as well as prevention of tissue ischaemia and vascular damage. Comorbidities need to be considered when assessing disease activity and selecting treatment. CONCLUSION: These are the first T2T recommendations for GCA and PMR. Treatment targets, as well as strategies to assess, achieve and maintain these targets have been defined. The research agenda highlights the gaps in evidence and the need for future research.

Urban air quality and human health are among the key aspects of future urban planning. In order to address pollutants such as ozone and particulate matter, efforts need to be made to quantify and reduce their concentrations. One important aspect in understanding urban air quality is the influence of urban vegetation which may act as both emitter and sink for trace gases and aerosol particles. In this context, the "Berlin Air quality and Ecosystem Research: Local and long-range Impact of anthropogenic and Natural hydrocarbons 2014" (BAERLIN2014) campaign was conducted between 2 June and 29 August in the metropolitan area of Berlin and Brandenburg, Germany. The predominant goals of the campaign were (1) the characterization of urban gaseous and particulate pollution and its attribution to anthropogenic and natural sources in the region of interest, especially considering the connection between biogenic volatile organic compounds and particulates and ozone; (2) the quantification of the impact of urban vegetation on organic trace gas levels and the presence of oxidants such as ozone; and (3) to explain the local heterogeneity of pollutants by defining the distribution of sources and sinks relevant for the interpretation of model simulations. In order to do so, the campaign included stationary measurements at urban background station and mobile observations carried out from bicycle, van and airborne platforms. This paper provides an overview of the mobile measurements (Mobile BAERLIN2014) and general conclusions drawn from the analysis. Bicycle measurements showed micro-scale variations of temperature and particulate matter, displaying a substantial reduction of mean temperatures and particulate levels in the proximity of vegetated areas compared to typical urban residential area (background) measurements. Van measurements extended the area covered by bicycle observations and included continuous measurements of O3, NOx, CO, CO2 and point-wise measurement of volatile organic compounds (VOCs) at representative sites for traffic- and vegetation-affected sites. The quantification displayed notable horizontal heterogeneity of the short-lived gases and particle number concentrations. For example, baseline concentrations of the traffic-related chemical species CO and NO varied on average by up to ±22.2 and ±63.5 %, respectively, on the scale of 100 m around any measurement location. Airborne observations revealed the dominant source of elevated urban particulate number and mass concentrations being local, i.e., not being caused by long-range transport. Surface-based observations related these two parameters predominantly to traffic sources. Vegetated areas lowered the pollutant concentrations substantially with ozone being reduced most by coniferous forests, which is most likely caused by their reactive biogenic VOC emissions. With respect to the overall potential to reduce air pollutant levels, forests were found to result in the largest decrease, followed by parks and facilities for sports and leisure. Surface temperature was generally 0.6–2.1 °C lower in vegetated regions, which in turn will have an impact on tropospheric chemical processes. Based on our findings, effective future mitigation activities to provide a more sustainable and healthier urban environment should focus predominantly on reducing fossil-fuel emissions from traffic as well as on increasing vegetated areas.

Abstract 12-oxophytodienoate reductase 3 (OPR3) is a key enzyme in the biosynthesis of jasmonoyl-L-isoleucine, the receptor-active form of jasmonic acid and crucial signaling molecule in plant defense. OPR3 was initially crystallized as a self-inhibitory dimer, implying that homodimerization regulates enzymatic activity in response to biotic and abiotic stresses. Since a sulfate ion is bound to Y364, mimicking a phosphorylated tyrosine, it was suggested that dimer formation might be controlled by reversible phosphorylation of Y364 in vivo. To investigate OPR3 homodimerization and its potential physiological role in more detail, we performed analytical gel filtration and dynamic light scattering on wild-type OPR3 and three variants (R283D, R283E, and Y364P). The experiments revealed a rapid and highly sensitive monomer–dimer equilibrium for all OPR3 constructs. We crystallized all constructs with and without sulfate to examine its effect on the dimerization process and whether reversible phosphorylation of Y364 triggers homodimerization in vivo. All OPR3 constructs crystallized in their monomeric and dimeric forms independent of the presence of sulfate. Even variant Y364P, lacking the putative phosphorylation site, was crystallized as a self-inhibitory homodimer, indicating that Y364 is not required for dimerization. Generally, the homodimer is relatively weak, and our results raise doubts about its physiological role in regulating jasmonate biosynthesis.

Abstract Heat engines are key devices that convert thermal energy into usable energy. Strong thermoelectricity, at the basis of electrical heat engines, is present in superconducting spin tunnel barriers at cryogenic temperatures where conventional semiconducting or metallic technologies cease to work. Here we realize a superconducting spintronic heat engine consisting of a ferromagnetic insulator/superconductor/insulator/ferromagnet tunnel junction (EuS/Al/AlO x /Co). The efficiency of the engine is quantified for bath temperatures ranging from 25 mK up to 800 mK, and at different load resistances. Moreover, we show that the sign of the generated thermoelectric voltage can be inverted according to the parallel or anti-parallel orientation of the two ferromagnetic layers, EuS and Co. This realizes a thermoelectric spin valve controlling the sign and strength of the Seebeck coefficient, thereby implementing a thermoelectric memory cell. We propose a theoretical model that allows describing the experimental data and predicts the engine efficiency for different device parameters.

The HOVERT (HOrizontal and VERtical Transport of ozone and particulate matter) campaign held in the Berlin Brandenburg area in Eastern Germany from September 2001 to September 2002 allowed to collect a unique data set of the aerosol chemical speciation (daily averages) at traffic, urban and rural sites. These observations are used for a thorough evaluation of the aerosol part in the REM-CALGRID model (RCG) developed at the Free University of Berlin (FUB). For inorganic ions (sulphate, nitrate and ammonium), simulated annual averages agree to observations within ±30% at more than half of the sites and always within a factor of two. Correlation coefficients are larger than in previous studies for SO42− and NH4+ (>0.7). For nitrate, less elevated correlations, 0.4–0.7 in the cold season, 0.2–0.4 in the warm season, are encountered. To our knowledge, this is one of the first comparisons of air quality model simulated elemental and organic carbon (EC and OC) with daily observations for a whole year. It suggests an overestimation of EC and OC emissions in the Berlin area (through a scaling techniques between EC, OC and NOx and when assuming correct NOx emissions), and an underestimation of EC and OC at rural sites. Secondary organic aerosol (SOA) formation, recently introduced into the model (SORGAM module, Schell et al., 2001), is simulated as a very variable process, SOA levels varying from close to zero for most days to more than 5 μg/m3. Correlation between simulated SOA to observed OC is about 0.6, indicating that simulated variability partly corresponds to reality.

Abstract Claws, as nature's multifaceted instruments, play fundamental roles across the animal kingdom, aiding in prey capture and enabling movement across diverse terrains. Claw features often reflect the ecologies of the respective taxa and thus can provide important insights into the different lifestyles. This study explores the claw morphology of monodactylous oribatid mites through geometric morphometrics, analyzing 559 specimens from 49 species across various ecosystems. The research identifies distinct claw characteristics associated with specific habitats, revealing a significant correlation between claw morphology and the mites' environmental adaptations. Littoral mites exhibit notably larger claws compared to terrestrial counterparts, with aquatic and semiaquatic species presenting intermediate traits. The analysis shows an inverse relationship between claw curvature and sharpness, differing from patterns observed in larger animals. A trend of increasing claw bluntness with body size in terrestrial mites echoes biomechanical constraints seen in larger species. The study also observes consistent claw shapes within oribatid superfamilies, suggesting a potential, albeit muted, phylogenetic influence alongside environmental factors. These findings reveal how ecological, evolutionary, and functional aspects influence claw morphology in oribatid mites, enhancing our knowledge of arthropod biology and potentially inspiring biomimetic advances in material science and engineering.

This study aims to evaluate the clinical outcome of stereotactic radiosurgery as the sole treatment for brain metastases and to assess prognostic factors influencing survival. A total of 108 consecutive patients with 213 metastases were retrospectively analyzed. Treatment was determined with close-meshed MRI follow-up. Various prognostic factors were assessed, and several prognostic indices were compared regarding their reliability to estimate overall survival. Median overall survival was 15 months; one-year overall survival was 50.5%. Both one- and two-year local controls were 90.9%. The rate of new metastases after SRS was 49.1%. Multivariate analysis of prognostic factors revealed that the presence of extracranial metastases, male sex, lower KPI, and progressive extracranial disease were significant risk factors for decreased survival. Of all evaluated prognostic indices, the Basic Score for Brain Metastases (BSBMs) showed the best correlation with overall survival. A substantial survival advantage was found for female patients after SRS when compared to male patients (18 versus 9 months, p = 0.003). SRS of brain metastasis is a safe and effective treatment option when frequent monitoring for new metastases with MRI is performed. Common prognostic scores lack reliable estimation of survival times. Female sex should be considered as an additional independent positive prognostic factor influencing survival.

In less than a decade, additive manufacturing technologies have been developed so successfully that they already produce small and medium-sized lot sizes of prototypes or customised components in the industry. With its new possibilities such as combining materials and technologies, the benefits of different technologies can be merged and broaden future application fields. One way is to print with one technology on a part produced by another. Thus, a thermally bonded part composed of, e.g., selectively sintered and material-extruded components can be created. This combination of technologies was considered in this study to investigate the bonding strength of extrusion-based layers on selectively sintered surfaces and the impact of nozzle temperature, orientation, and thickness of imprinted materials. The extrusion-based layers covered stiff (fibre-reinforced polyamide) and soft (thermoplastic polyurethane) material properties with pre-cracked single-leg bending (SLB) specimens to study their effect on delamination tendencies. This combination of materials and additive manufacturing technologies has not yet been studied for the SLB testing method. The scope of this study is to obtain more information on how relatively hard-hard and hard-soft combinations behave for this special testing method. The results of this testing method were evaluated using two different fracture mechanical approaches to determine the energy release rate. A clear trend towards an improved bonding, thus, higher values, was found for higher nozzle temperatures. Furthermore, a limitation regarding the required bending stiffness of the composites was found. Overall, the single-leg bending testing method enables a relative ranking for material combinations with a certain bending stiffness.

The paper presents an estimate of emission source influence on PM10 concentrations in Berlin. Particulate matter less than 10 μm in aerodynamic diameter (PM10) is a conglomerate of different chemical components related to distinct sources and physico-chemical processes in the atmosphere and lithosphere. Emission reduction thus has temporally and spatially varying effects on different scales. Urban PM10 concentrations are heavily influenced by long range transport (up to 70%) from remote source areas, whereas rural air pollution is strongly determined by urban emissions. By means of emission reduction scenario simulations with a chemistry-transport-model it has been found that on average two third of the urban background concentrations in Berlin are due to Berlin-specific emissions. This percentage varies strongly considering primary and secondary components: only about 5% of secondary PM10 concentrations are related to local emissions, while approximately 70% of primary concentrations stem from the urban sources. City related emissions influence homogenously the rural air-pollution concentrations, but with different ranges of influence.

BackgroundThe acquisition of handwriting skills is essential for a child’s academic success, self-confidence, and general school performance. Nevertheless, an estimated 5% to 27% of children face handwriting challenges, where the ability to modulate pressure on the pencil and lead on the paper is a key motor component. ObjectiveWe aimed to investigate the experience with and usability of the SensoGrip system, a pressure-measuring pen system with personalized real-time feedback about pressure modulation, in a clinical setting with children and occupational therapists (OTs). MethodsA multimethods study was conducted, incorporating qualitative interviews and questionnaires with children, user diaries, focus group discussions, and a usability questionnaire with OTs, along with a questionnaire for parents. ResultsThe study involved OTs (n=8), children with handwriting difficulties (n=16), and their parents (n=16), each of whom used the SensoGrip system in up to 5 therapy sessions. OTs reported that the SensoGrip system helped to focus the child’s awareness on handwriting pressure and to measure it objectively. The system received high acceptance and usability ratings from the OTs—usefulness: median score of 4 out of 7; ease of use and ease of learning: median score of 6 out of 7; and satisfaction: median score of 6 out of 7. Participants appreciated that it fosters pressure awareness and motivation to draw and write. ConclusionsThe SensoGrip pressure-sensing system with real-time feedback is a promising tool for pediatric occupational therapy. It supports children with handwriting difficulties to adjust their pressure application during the task. In the future, controlled quantitative trials are warranted to further examine the system’s impact.

Selecting the optimal settings for the production of rubber goods can be a very time-consuming and resource-intensive process. A promising method for optimizing rubber processing in a short period of time is the use of simulation routines. However, process simulations have only recently enabled meaningful predictions of not only the part’s state of cure but also its mechanical characteristics. As a first approach, second-order polynomials were considered suitable for describing the properties of compression-molded parts. However, more precision is required for injection molding due to the narrower distribution of mechanical characteristics of parts produced at different vulcanization temperatures. This became evident when the approximation of mechanical data with second order models partly revealed significant failures of part behavior prediction. To tackle this issue, a combined approach for approximation is proposed in this contribution by means of logistic growth function in addition to second order polynomials. To feed the model, an experimental plan was designed for producing injection-molded parts from an SBR compound at various temperatures and to different degrees of cure. The parts obtained were then characterized mechanically, and the results were opposed to varying degrees of cure and extents of reaction to calculate the model coefficients. Once available, a simulation-based calculation of the mechanical part quality is possible. The comparison of test results from the simulation and the real process has shown a reliable prediction, as simulation results were found within the natural deviation of the real measurements.

Osteoarthritis, predominantly of the knee, is a highly prevalent disease leading to pain, reduced quality of life, and significantly reduced ability to work. With autologous orthobiologic options, new regenerative treatment methods have emerged, offering an alternative to early surgical intervention. Supercharged Liparthroplasty combines arthroscopy with lipoaspirate and plasma infiltration of the joint. Lipoaspirate contains high levels of adipose-derived stem cells, which show chondroprotective and anti-inflammatory qualities. Intra-articular injection, combined with platelet-rich plasma administration for accelerated cartilage metabolism, thus provides an optional approach in osteoarthritis treatment. This article aims to provide in detail our regimen for Supercharged Liparthroplasty, including tissue harvesting and preparation of the injectables, therefore enabling physicians to adopt this point-of-care technique.

Effects of mowing on vegetation parameters have been well studied. However, less is known about mowing effects on soil fauna and if soil properties alter this. We investigated earthworm communities in a long-term experiment 14 years after its establishment in 5 dry, fresh and moist grassland plots located in the Natura 2000 site Lainzer Tiergarten near Vienna, Austria (238–402 m a.s.l., 48°10′ N, 16°12′ E). The grasslands were either mowed once a year or every second year, or not mowed since being established. Earthworms were assessed using the non-destructive octet electro-shocking method. Additionally, vegetation composition, soil conductivity, temperature and moisture were assessed. We found 13 earthworm species across all treatments, although their abundance was generally low with 6.1 ± 4.7 worms m−2. The total earthworm abundance and species diversity was higher in dry compared to fresh and moist grasslands but was not affected by mowing frequency. Endogeic earthworms (Aporrectodea caliginosa, Aporrectodea rosea) and epigeics (Lumbricus rubellus) were more tolerant to mowing than anecics (Lumbricus terrestris, Allolobophora longa). Since plant species richness was highest in annually mown grasslands and earthworm species richness was positively related to plant species numbers, we recommend regular, low-input management to promote above- and belowground biodiversity in these grasslands.