Search

Subacromial impingement (SAI) is associated with shoulder pain and dysfunction and is exacerbated by rotator cuff tears; however, the role of acromioplasty in mitigating subacromial contact in the rotator cuff deficient shoulder remains debated. This study aimed to quantify the influence of isolated and combined tears involving the supraspinatus on subacromial contact during abduction; and second, to evaluate the influence of acromioplasty on joint space size and subacromial contact under these pathological conditions. Eight fresh-frozen human cadaveric upper limbs were mounted to a computer-controlled testing apparatus that simulated joint motion by simulated force application. Shoulder abduction was performed while three-dimensional joint kinematics was measured using an optoelectronic system, and subacromial contact evaluated using a digital pressure sensor secured to the inferior acromion. Testing was performed after an isolated tear to the supraspinatus, as well as tears involving the subscapularis and infraspinatus-teres minor, both before and after acromioplasty. Rotator cuff tears significantly increased peak subacromial pressure (p < 0.001), average subacromial pressure (p = 0.001), and contact force (p = 0.034) relative to those in the intact shoulder. Following acromioplasty, significantly lower peak subacromial contact pressure, force and area were observed for all rotator cuff tears involving the supraspinatus at 30° of abduction (p < 0.05). Acromioplasty predominantly reduces acromion thickness anteriorly thereby reducing subacromial contact in the rotator cuff deficient shoulder, particularly in early to mid-abduction where superior glenohumeral joint shear force potential is large. These findings provide a biomechanical basis for acromioplasty as an intervention for SAI syndrome and as an adjunct to rotator cuff repairs.

The Latarjet procedure is an established surgical treatment for recurrent glenohumeral joint instability with glenoid bone loss. Intraoperatively, the conjoint tendon and its attachement on the coracoid bone graft is routed through a split in subscapularis where the graft is fixed to and augments the anteroinferior glenoid. The objective of this in vitro study was to quantify the influence of glenohumeral joint position and conjoint tendon force on the lines of action and moment arms of subscapularis muscle sub-regions after Latarjet surgery. Eight fresh-frozen, entire upper extremities were mounted onto a testing apparatus, and a cable-pulley system was used to apply physiological muscle loading to the major shoulder muscles. The lines of action and moment arms of four subregions of subscapularis (superior, mid-superior, mid-inferior, and inferior) were quantified radiographically with the conjoint tendon unloaded and loaded while the shoulder was in (i) 0° abduction (ii) 90° abduction (iii) 90° abduction and full external rotation (ABER), and (iv) the apprehension position, defined as ABER with 30° horizontal extension. Conjoint tendon loading after Latarjet surgery significantly increased the inferior inclination of the lines of action of the mid-inferior and inferior subregions of subscapularis in the scapular plane in ABER and apprehension positions (p < 0.001), as well as decreased the horizontal flexion moment arm of the inferior subscapularis (p = 0.040). Increased subscapularis inferior inclination may ultimately increase inferior joint shear potential, while smaller horizontal flexion leverage may reduce joint flexion capacity. The findings have implications for Latarjet surgical planning and postoperative rehabilitation prescription.

Total temporomandibular joint replacement (TMJR) surgery is the established treatment for severe temporomandibular joint disorders. While TMJR surgery is known to increase mouth-opening capacity, reduce pain and improve quality of life, little is known about post-surgical jaw function during activities of daily living such as biting and chewing. The aim of this study was to use subject-specific 3D bite force measurements to evaluate the magnitude and direction of joint loading in unilateral total TMJR patients and compare these data to those in healthy control subjects. An optoelectronic tracking system was used to measure jaw kinematics while biting a rubber sample for 5 unilateral total TMJR patients and 8 controls. Finite element simulations driven by the measured kinematics were employed to calculate the resultant bite force generated when compressing the rubber between teeth during biting tasks. Subject-specific musculoskeletal models were subsequently used to calculate muscle and TMJ loading. Unilateral total TMJR patients generated a bite force of 249.6 ± 24.4 N and 164.2 ± 62.3 N when biting on the contralateral and ipsilateral molars, respectively. In contrast, controls generated a bite force of 317.1 ± 206.6 N. Unilateral total TMJR patients biting on the contralateral molars had a significantly higher lateral TMJ force direction (median difference: 63.6°, p = 0.028) and a significantly lower ratio of working TMJ force to bite force (median difference: 0.17, p = 0.049) than controls. Results of this study may guide TMJ prosthesis design and evaluation of dental implants.

Full-thickness rotator cuff tears can lead to poor coaptation of the humeral head to the glenoid, disrupting muscle forces required for glenohumeral joint stability, ultimately leading to joint subluxation. The aim of this study was to evaluate muscle forces and glenohumeral joint translations during elevation in the presence of isolated and combined full-thickness rotator cuff tears. Eight fresh-frozen upper limbs were mounted to a computer-controlled testing apparatus that simulated joint motion by simulated muscle force application. Scapular-plane abduction was performed, and glenohumeral joint translations were measured using an optoelectronic system. Testing was performed in the native shoulder, a following an isolated tear to the supraspinatus, as well as combined tears involving the supraspinatus and subscapularis, as well as supraspinatus, infraspinatus, and teres minor. Rotator cuff tears significantly increased middle deltoid force at 30°, 60°, and 90° of abduction relative to that in the native shoulder (p < 0.05). Significantly greater superior translations were observed relative to the intact shoulder due to combined tears to the supraspinatus and infraspinatus at 30° of abduction (mean increase: 1.6 mm, p = 0.020) and 60° of abduction (mean increase: 4.8 mm, p = 0.040). This study illustrates the infraspinatus-teres minor complex as a major humeral head depressor and contributor to glenohumeral joint stability. An increase in deltoid force during abduction occurs in the presence of rotator cuff tears, which exacerbates superior migration of the humeral head. The findings may help in the development of clinical tests in rotator cuff tear diagnostics, in surgical planning of rotator cuff repair, and in planning of targeted rehabilitation.

The ligamentous structures of the wrist stabilise and constrain the interactions of the carpal bones during active wrist motion; however, the three-dimensional translations and rotations of the scaphoid, lunate and capitate in the normal and ligament deficient wrist during planar and oblique wrist motions remain poorly understood. This study employed a computer-controlled simulator to replicate physiological wrist motion by dynamic muscle force application, while carpal kinematics were simultaneously measured using bi-plane x-ray fluoroscopy. The aim was to quantify carpal kinematics in the native wrist and after sequential sectioning of the scapholunate interosseous ligament (SLIL) and secondary scapholunate ligament structures. Seven fresh-frozen cadaveric wrist specimens were harvested, and cycles of flexion-extension, radial-ulnar deviation and dart-thrower's motion were simulated. The results showed significant rotational and translational changes to these carpal bones in all stages of disruptions to the supporting ligaments (p < 0.05). Specifically, following the disruption of the dorsal SLIL (Stage II), the scaphoid became significantly more flexed, ulnarly deviated, and pronated relative to the radius, whereas the lunate became more extended, supinated and volarly translated (p < 0.05). Sectioning of the dorsal intercarpal (DIC), dorsal radiocarpal (DRC), and scaphotrapeziotrapezoid (STT) ligaments (Stage IV) caused the scaphoid to collapse further into flexion, ulnar deviation, and pronation. These findings highlight the importance of all the ligamentous attachments that relate to the stability of the scapholunate joint, but more importantly, the dorsal SLIL in maintaining scapholunate stability, and the preservation of the attachments of the DIC and DRC ligaments during dorsal surgical approaches. The findings will be useful in diagnosing wrist pathology and in surgical planning.

Total temporomandibular joint (TMJ) replacement surgery aims to improve mandibular function, reduce pain and enhance quality of life in patients suffering from end-stage TMJ disorders. Traditional post-operative jaw evaluation is carried out using measurement of maximum interincisal opening distance; however, this can correlate poorly to joint function. The present study aimed to evaluate three-dimensional (3D) jaw motion during border movements and chewing in unilateral total TMJ replacement patients and healthy controls. Motion analysis experiments were performed on six unilateral total TMJ replacement patients and ten age-matched healthy controls. Subject-specific motion tracking plates worn by each participant were registered to CT scans of each participant's skull and mandible to enable anatomical mandibular kinematics measurement using an optoelectronic system. Participants performed 15 repetitions of maximal opening, protrusion, lateral excursions, and chewing cycles. Total TMJ replacement patients had significantly smaller incisal displacements at maximum mouth opening relative to the controls (median difference: 7.1 mm, p = 0.002) and decreased anterior translation of the prosthetic condyle (median difference: 10.5 mm, p = 0.002). When TMJ replacement subjects chewed using their contralateral molars, there was a significant increase in inferior condylar translation of the non-working condyle (median difference: 9.7 mm, p = 0.016). This study found that unilateral total TMJ replacement surgery was associated with mouth opening capacity within the range of healthy individuals, but reduced anterior movement of the prosthetic condyle and restricted protrusion and lateral excursions. The results provide future direction for prosthetic TMJ design to enhance postsurgical implant functionality and improve long-term clinical outcomes for prosthesis recipients.

BACKGROUND: Total joint replacements are an established treatment for patients suffering from reduced mobility and pain due to severe joint damage. Aseptic loosening due to stress shielding is currently one of the main reasons for revision surgery. As this phenomenon is related to a mismatch in mechanical properties between implant and bone, stiffness reduction of implants has been of major interest in new implant designs. Facilitated by modern additive manufacturing technologies, the introduction of porosity into implant materials has been shown to enable significant stiffness reduction; however, whether these devices mitigate stress-shielding associated complications or device failure remains poorly understood. METHODS: In this systematic review, a broad literature search was conducted in six databases (Scopus, Web of Science, Medline, Embase, Compendex, and Inspec) aiming to identify current design approaches to target stress shielding through controlled porous structures. The search keywords included 'lattice,' 'implant,' 'additive manufacturing,' and 'stress shielding.' RESULTS: After the screening of 2530 articles, a total of 46 studies were included in this review. Studies focusing on hip, knee, and shoulder replacements were found. Three porous design strategies were identified, specifically uniform, graded, and optimized designs. The latter included personalized design approaches targeting stress shielding based on patient-specific data. All studies reported a reduction of stress shielding achieved by the presented design. CONCLUSION: Not all studies used quantitative measures to describe the improvements, and the main stress shielding measures chosen varied between studies. However, due to the nature of the optimization approaches, optimized designs were found to be the most promising. Besides the stiffness reduction, other factors such as mechanical strength can be considered in the design on a patient-specific level. While it was found that controlled po

BACKGROUND: Lumbar interbody fusion (LIF) is an established surgical intervention for patients with leg and back pain secondary to disc herniation or degeneration. Interbody fusion involves removal of the herniated or degenerated disc and insertion of interbody devices with bone grafts into the remaining cavity. Extensive research has been conducted on operative complications such as a failure of fusion or non-union of the vertebral bodies. Multiple factors including surgical, implant, and patient factors influencing the rate of complications have been identified. Patient factors include age, sex, osteoporosis, and patient anatomy. Complications can also be influenced by the interbody cage design. The geometry of the bony endplates as well as their corresponding material properties guides the design of interbody cages, which vary considerably across patients with spinal disorders. However, studies on the effects of such variations on the rate of complications are limited. Therefore, this study aimed to perform a systematic review of lumbar endplate geometry and material property factors in LIF failure. METHODS: Search keywords included 'factor/cause for spinal fusion failure/cage subsidence/cage migration/non-union', 'lumbar', and 'interbody' in electronic databases PubMed and Scopus with no limits on year of publication. RESULTS: In total, 1341 articles were reviewed, and 29 articles were deemed suitable for inclusion. Adverse events after LIF, such as cage subsidence, cage migration, and non-union, resulted in fusion failure; hence, risk factors for adverse events after LIF, notably those associated with lumbar endplate geometry and material properties, were also associated with fusion failure. Those risk factors were associated with shape, concavity, bone mineral density and stiffness of endplate, segmental disc angle, and intervertebral disc height. CONCLUSIONS: This review demonstrated that decreased contact areas between the cage and endplate, thin and weak bo

BACKGROUND: Acromial and scapular spine fractures after reverse total shoulder arthroplasty (RTSA) can be devastating complications leading to substantial functional impairments. The purpose of this study was to review factors associated with increased acromial and scapular spine strain after RTSA from a biomechanical standpoint. METHODS: A systematic review of the literature was conducted based on PRISMA guidelines. PubMed, Embase, OVID Medline, and CENTRAL databases were searched and strict inclusion and exclusion criteria were applied. Each article was assessed using the modified Downs and Black checklist to appraise the quality of included studies. Study selection, extraction of data, and assessment of methodological quality were carried out independently by two of the authors. Only biomechanical studies were considered. RESULTS: Six biomechanical studies evaluated factors associated with increased acromial and scapular spine strain and stress. Significant increases in acromial and scapular spine strain were found with increasing lateralization of the glenosphere in four of the included studies. In two studies, glenosphere inferiorization consistently reduced acromial strain. The results concerning humeral lateralization were variable between four studies. Humeral component neck-shaft angle had no significant effect on acromial strain as analysed in one study. One study showed that scapular spine strain was significantly increased with a more posteriorly oriented acromion (55° vs. 43°; p < 0.001). Another study showed that the transection of the coracoacromial ligament increased scapular spine strain in all abduction angles (p < 0.05). CONCLUSIONS: Glenoid lateralization was consistently associated with increased acromial and scapular spine strain, whereas inferiorization of the glenosphere reduced strain in the biomechanical studies analysed in this systematic review. Humeral-sided lateralization may increase or decrease acromial or scapular spine strain. Indep

Bone graft resorption following the Latarjet procedure has received considerable concern. Current methods quantifying bone graft resorption rely on two-dimensional (2D) CT-scans or three-dimensional (3D) techniques, which do not represent the whole graft volume/resorption (i.e., 2D assessment) or expose patients to additional radiation (i.e., 3D assessment) as this technique relies on early postoperative CT-scans. The aim of the present study was to develop and validate a patient-specific, CT-morphometric technique combining image registration with 3D CT-reconstruction to quantify bone graft resorption following the Latarjet procedure for recurrent anterior shoulder instability. Pre-operative and final follow-up CT-scans were segmented to digitally reconstruct 3D scapula geometries. A virtual Latarjet procedure was then conducted to model the timepoint-0 graft volume, which was compared with the final follow-up graft volume. Graft resorption at final follow-up was highly correlated to the 2D gold standard-technique by Zhu (Kendall tau coefficient = 0.73; p < 0.001). The new technique was also found to have excellent inter- and intra-rater reliability (ICC values, 0.931 and 0.991; both p < 0.001). The main finding of this study is that the technique presented is a valid and reliable method that provides the advantage of 3D-assessment of graft resorption at long-term follow-up without the need of an early postoperative CT-scan.

Dynamic occlusal loading during mastication is clinically relevant in the design and functional assessment of dental restorations and removable dentures, and in evaluating temporomandibular joint dysfunction. The aim of this study was to develop a modelling framework to evaluate subject-specific dynamic occlusal loading during chewing and biting over the entire dental arch. Measurements of jaw motion were performed on one healthy male adult using low-profile electromagnetic field sensors attached to the teeth, and occlusal anatomy quantified using an intra-oral scanner. During testing, the subject chewed and maximally compressed a piece of rubber between both second molars, first molars, premolars and their central incisors. The occlusal anatomy, rubber geometry and experimentally measured rubber material properties were combined in a finite element model. The measured mandibular motion was used to kinematically drive model simulations of chewing and biting of the rubber sample. Three-dimensional dynamic bite forces and contact pressures across the occlusal surfaces were then calculated. Both chewing and biting on the first molars produced the highest bite forces across the dental arch, and a large amount of anterior shear force was produced at the incisors and the second molars. During chewing, the initial tooth-rubber contact evolved from the buccal sides of the molars to the lingual sides at full mouth closure. Low-profile electromagnetic field sensors were shown to provide a clinically relevant measure of jaw kinematics with sufficient accuracy to drive finite element models of occlusal loading during chewing and biting. The modelling framework presented provides a basis for calculation of physiological, dynamic occlusal loading across the dental arch.

Reverse total shoulder arthroplasty (RTSA) is an established treatment for elderly patients with irreparable rotator cuff tears, complex proximal humerus fractures, and revision arthroplasty; however, with the increasing indications for RTSA over the last decade and younger implant recipients, post-operative complications have become more frequent, which has driven advances in computational modeling and simulation of reverse shoulder biomechanics. The objective of this study was to provide a review of previously published studies that employed computational modeling to investigate complications associated with RTSA. Models and applications were reviewed and categorized into four possible complications that included scapular notching, component loosening, glenohumeral joint instability, and acromial and scapular spine fracture, all of which remain a common cause of significant functional impairment and revision surgery. The computational shoulder modeling studies reviewed were primarily used to investigate the effects of implant design, intraoperative component placement, and surgical technique on postoperative shoulder biomechanics after RTSA, with the findings ultimately used to elucidate and mitigate complications. The most significant challenge associated with the development of computational models is in the encapsulation of patient-specific anatomy and surgical planning. The findings of this review provide a basis for future direction in computational modeling of the reverse shoulder.

The use of video and music as an intrinsic, dissociative attentional stimulus during exercise is thought to distract from the physical discomfort of exercise, and contribute to improved exercise adherence; however, the effects of video-based feedback and engagement during pedaling on exercise performance and motivation are poorly understood. The aims of the present study were twofold. Firstly, to develop a novel video-based engagement regime for pedaling that links pedaling cadence with the play rate of a video, and secondly, to employ an instrumented pedaling device to assess the influence of the video engagement paradigm on cadence performance and exercise motivation. Eighteen healthy subjects participated in 15-min-duration pedaling sessions while targeting a specific low cadence (60 rotations per minute) and high cadence (100 rotations per minute), including pedaling with the provision of (i) target pedaling cadence information only, (ii) visual feedback on cadence control, including pedaling duration, pedaling cadence, and cadence deviation from target, and (iii) real-time engagement, which involved pedaling at the target speed to maintain the playback rate of a pre-recorded video. Cadence deviation from the target was evaluated, and self-reported exercise motivation examined with a post-exercise survey. Pedaling-cadence deviations significantly reduced with cadence feedback at both low and high cadence (p < 0.05). Participants reported enjoying feedback and video-based engagement during pedaling, with 83% of participants feeling that engagement motivated them to perform pedaling-based exercise. In conclusion, real-time cadence control feedback and video-based engagement during pedaling for healthy individuals may improve performance in targeted pedaling tasks. Through dissociation from the physical cues associated with exercise and fatigue, feedback and engagement may ultimately increase enjoyment and exercise compliance and adherence of pedaling-based exercis

BACKGROUND: Dual orthogonal plating of clavicle fractures may provide greater stiffness and strength than unilateral plate constructs and allow the use of lower-profile plates. We aim to biomechanically compare three clavicle plating constructs in a comminuted clavicle fracture model. METHOD: Fifteen clavicle sawbones were osteotomised, simulating a comminuted midshaft fracture and allocated to either: group 1, single superior plate (3.5 mm superior plate); group 2, combination plating (3.5 mm superior plate, 2.8 mm anterior plate) and group 3, dual mini-plates (two 2.8-mm orthogonal mini-plates). Specimens were biomechanically tested under torsion and cantilever bending. Construct stiffness (Nm/degree) and load to failure (Nm) were measured. RESULTS: Group 2 had higher torsional (0.70 vs. 0.60 Nm/deg, p = 0.017) and cantilever bending stiffness (0.61 vs. 0.51 Nm/deg, p = 0.025) than group 1. Group 3 had lower cantilever bending stiffness (0.39 vs. 0.51 Nm/deg, p < 0.004) and load to failure (40.87 vs. 54.84 Nm, p < 0.01) than group 1. All dual plate constructs that catastrophically failed did so from fracture at the lateral ends of the plates. Single plate constructs failed due to plate bending. CONCLUSION: Dual orthogonal fixation with mini-plates demonstrated lower stiffness and strength than traditional superior plating. The addition of an anterior mini-plate to a traditional superior plating improved construct stiffness and may have a role in patients seeking early return to activity. LEVEL OF EVIDENCE: Basic science biomechanical study.

Motion of the mandible and temporomandibular joint (TMJ) plays a pivotal role in the function of the dentition and associated hard and soft tissue structures, and facilitates mastication, oral communication and access to respiratory and digestive systems. Quantification of TMJ kinematics is clinically relevant in cases of prosthetic rehabilitations, TMJ disorders, osteoarthritis, trauma, tumour resection and congenital abnormalities, which are known to directly influence mandibular motion and loading. The objective of this systematic review was to critically investigate published literature on historic and contemporary measurement modalities used to quantify in vivo mandibular and TMJ kinematics in six degrees of freedom. The electronic databases of Scopus, Web of Science, Medline, Embase and Central were searched and 109 relevant articles identified. Publication quality was documented using a modified Downs and Black checklist. Axiography and ultrasonic tracking are commonly employed in the clinical setting due to their simplicity and capacity to rapidly acquire low-fidelity mandibular motion data. Magnetic and optoelectronic tracking have been used in combination with dental splints to produce higher accuracy measurements while minimising skin motion artefact, but at the expense of setup time and cost. Four-dimensional computed tomography provides direct 3D measurement of mandibular and TMJ motion while circumventing skin motion artefact entirely, but employs ionising radiation, is restricted to low sampling frequencies, and requires time-consuming image processing. Recent advances in magnetic tracking using miniature sensors adhered to the teeth in combination with intraoral scanning may facilitate rapid and high precision mandibular kinematics measurement in the clinical setting. The findings of this review will guide selection and application of mandibular and TMJ kinematic measurement for both clinical and research applications.

BACKGROUND CONTEXT: While burst fracture is a well-known cause of spinal canal occlusion with dynamic, axial spinal compression, it is unclear how such loading mechanisms might cause occlusion without fracture. PURPOSE: To determine how spinal canal occlusion during dynamic compression of the lumbar spine is differentially caused by fracture or mechanisms without fracture and to examine the influence of spinal level on occlusion. STUDY DESIGN: A cadaveric biomechanical study. METHODS: Twenty sets of three-vertebrae specimens from all spinal levels between T12 and S1 were subjected to dynamic compression using a hydraulic loading apparatus up to a peak velocity between 0.1 and 0.9 m/s. The presence of canal occlusion was measured optically with a high-speed camera. This was repeated with incremental increases of 4% compressive strain until a vertebral fracture was detected using acoustic emission measurements and computed tomographic imaging. RESULTS: For axial compression without fracture, the peak occlusion (Omax) was 29.9±10.0%, which was deduced to be the result of posterior bulging of the intervertebral disc into the spinal canal. Omax correlated significantly with lumbar spinal level (p<.001), the compressive displacement (p<.001) and the cross-sectional area of the vertebra (p=.031). CONCLUSIONS: Spinal canal occlusion observed without vertebral fracture involves intervertebral disc bulging. The lower lumbar spine tended to be more severely occluded than more proximal levels. CLINICAL SIGNIFICANCE: Clinically, intermittent canal occlusion from disc bulging during dynamic compression may not show any radiographic features. The lower lumbar spine should be a focus of injury prevention intervention in cases of high-rate axial compression.

BACKGROUND: Osseointegrated implants for transfemoral amputees facilitate direct load transfer between the prosthetic limb and femur; however, implant loosening is a common complication, and the associated implant-bone loads remain poorly understood. This case study aimed to use patient-specific computational modeling to evaluate bone-implant interface loading during standing and walking in a transfemoral amputee with an osseointegrated implant prior to prosthesis loosening and revision surgery. METHODS: One male transfemoral amputee with an osseointegrated implant was recruited (age: 59-yrs, weight: 83 kg) and computed tomography (CT) performed on the residual limb approximately 3 months prior to implant failure. Gait analyses were performed, and the CT images used to develop a finite element model of the patient's implant and surrounding bone. Simulations of static weight bearing, and over-ground walking were then performed. FINDINGS: During standing, maximum and minimum principal strains in trabecular bone adjacent to the implant were 0.26% and -0.30%, respectively. Strains generated at the instant of contralateral toe-off and contralateral heel strike during walking were substantially higher and resulted in local trabecular bone yielding. Specifically, the maximum and minimum principal strains in the thin layer of trabecular bone surrounding the distal end of the implant were 1.15% and -0.98%, respectively. INTERPRETATION: Localised yielding of trabecular bone at the interface between the femur and implant in transfemoral amputee osseointegrated prosthesis recipients may present a risk of implant loosening due to periprosthetic bone fracture during walking. Rehabilitation exercises should aim to produce implant-bone loading that stimulates bone remodelling to provide effective bone conditioning prior to ambulation.

Direct skeletal attachment of prostheses in transfemoral amputees circumvents skin-interface complications associated with conventional sockets; however, joint pain and musculoskeletal disease is known to occur postoperatively. This study quantified hip contact forces and the roles of individual muscles in producing hip contact forces during walking in transfemoral amputees with osseointegrated prostheses. Musculoskeletal models were developed for four transfemoral amputees. Gluteus maximus and gluteus medius were the major contributors to the hip contact forces, and the intact limb hip muscles demonstrated greater contributions to hip contact forces than those of the residual limb. The findings may be useful for mitigating walking asymmetry.

Individuals with unilateral transfemoral amputation depend on compensatory muscle and joint function to generate motion of the lower limbs, which can produce gait asymmetry; however, the functional role of the intact and residual limb muscles of transfemoral amputees in generating progression, support, and mediolateral balance of the body during walking is not well understood. The aim of this study was to quantify the contributions of the intact and the residual limb's contralateral muscles to body center of mass (COM) acceleration during walking in transfemoral amputees. Three-dimensional subject-specific musculoskeletal models of 6 transfemoral amputees fitted with a socket-type prosthesis were developed and used to quantify muscle forces and muscle contributions to the fore-aft, vertical, and mediolateral body COM acceleration using a pseudo-inverse ground reaction force decomposition method during over-ground walking. Anterior pelvic tilt and hip range of motion in the sagittal and frontal planes of the intact limb was significantly larger than those in the residual limb (p<0.05). The mean contributions of the intact limb hip muscles to body COM support, forward propulsion and mediolateral balance were significantly greater than those in the residual limb (p<0.05). Gluteus maximus contributed more to propulsion and support, while gluteus medius contributed more to balance than other muscles in the intact limb than the residual limb. The findings demonstrate the role of the intact limb hip musculature in compensating for reduced or absent muscles and joint function in the residual limb of transfemoral amputees during walking. The results may be useful in developing rehabilitation programs and design of prostheses to improve gait symmetry and mitigate post-operative musculoskeletal pathology.

Surgical fixation of comminuted mid‐shaft clavicle fractures commonly employs intramedullary devices; however, pins with smooth surfaces are prone to migration, whilst threaded pins can be challenging to remove post‐operatively. The aim of this study was to evaluate the biomechanical performance of fractured clavicles repaired using a novel intramedullary Echidna pin device and a non‐threaded Knowles pin. The Echidna pin features retractable spines that engage with the bone to minimize migration and facilitate ease of device removal.

The moment arm of a muscle represents its leverage or torque-producing capacity, and is indicative of the role of the muscle in joint actuation. The objective of this study was to undertake a systematic review of the moment arms of the major muscles spanning the glenohumeral joint during abduction, flexion and axial rotation. Moment arm data for the deltoid, pectoralis major, latissimus dorsi, teres major, supraspinatus, infraspinatus, subscapularis and teres minor were reported when measured using the geometric and tendon excursion methods. The anterior and middle sub-regions of the deltoid had the largest humeral elevator moment arm values of all muscles during coronal- and scapular-plane abduction, as well as during flexion. The pectoralis major, latissimus dorsi and teres major had the largest depressor moment arms, with each of these muscles exhibiting prominent leverage in shoulder adduction, and the latissimus dorsi and teres major also in extension. The rotator cuff muscles had the largest axial rotation moment arms regardless of the axial position of the humerus. The supraspinatus had the most prominent elevator moment arms during early abduction in both the coronal and scapular planes as well as in flexion. This systematic review shows that the rotator cuff muscles function as humeral rotators and weak humeral depressors or elevators, while the three sub-regions of the deltoid behave as substantial humeral elevators throughout the range of humeral motion. The pectoralis major, latissimus dorsi and teres major are significant shoulder depressors, particularly during abduction. This study provides muscle moment arm data on functionally relevant shoulder movements that are involved in tasks of daily living, including lifting and pushing. The results may be useful in quantifying shoulder muscle function during specific planes of movement, in designing and validating computational models of the shoulder, and in planning surgical procedures such as tendon transf

Changes in joint architecture and muscle loading resulting from total shoulder arthroplasty (TSA) and reverse total shoulder arthroplasty (RSA) are known to influence joint stability and prosthesis survivorship. This study aimed to measure changes in muscle moment arms, muscle lines of action, as well as muscle and joint loading following TSA and RSA using a metal‐backed uncemented modular shoulder prosthesis. Eight cadaveric upper extremities were assessed using a customized testing rig. Abduction, flexion, and axial rotation muscle moment arms were quantified using the tendon‐excursion method, and muscle line‐of‐force directions evaluated radiographically pre‐operatively, and after TSA and revision RSA. Specimen‐specific musculoskeletal models were used to estimate muscle and joint loading pre‐ and post‐operatively. TSA lateralized the glenohumeral joint center by 4.3 ± 3.2 mm, resulting in small but significant increases in middle deltoid force (2.0%BW) and joint compression during flexion (2.1%BW) (p < 0.05). Revision RSA significantly increased the moment arms of the major abductors, flexors, adductors, and extensors, and reduced their peak forces (p < 0.05). The superior inclination of the deltoid significantly increased while the inferior inclination of the rotator cuff muscles decreased (p < 0.05). TSA using an uncemented metal‐backed modular shoulder prosthesis effectively restores native joint function; however, lateralization of the glenoid component should be minimized intra‐operatively to mitigate increased glenohumeral joint loading and polyethylene liner contact stresses. Revision RSA reduces muscle forces required during shoulder function but produces greater superior joint shear force and less joint compression. The findings may help to guide component selection and placement to mitigate joint instability after arthroplasty.

It is important to restore horizontal and vertical stability to the acromioclavicular (AC) joint when treating dislocations of this joint. Most surgical stabilization techniques of the AC joint have primarily addressed the coracoclavicular ligament complex; however, these techniques may not satisfactorily restore horizontal stability to the AC joint.

BACKGROUND: Intraoperative neurovascular complications with clavicle fracture fixation are often due to far cortex penetration by drills and screws, but could be avoided using a unicortical construct. The objective of this study was to compare the bending and torsional strength of a unicortical locking screw plate construct and a hybrid (with central locked and outer non-locked long oblique screws) unicortical plate construct for clavicle fracture fixation with that of a conventional bicortical locking screw construct of plate fixation. METHODS: Twenty-four human clavicle specimens were harvested and fractured in a comminuted mid-shaft butterfly configuration. Clavicles were randomly allocated to three surgical fixation groups: unicortical locking screw, bicortical locking screw and hybrid unicortical screw fixation. Clavicles were tested in torsion and cantilever bending. Construct bending and torsional stiffness were measured, as well as ultimate strength in bending. RESULTS: There were no significant differences in bending stiffness or ultimate bending moment between all three plating techniques. The unicortical locked construct had similar torsional stiffness compared with the bicortical locked construct; however, the hybrid technique was found to have significantly lower torsional stiffness to that of the bicortical locking screw construct (mean difference: 87.5 Nmm/degree, P = 0.028). CONCLUSIONS: Unicortical locked screw plate fixation and hybrid unicortical plating fixation with centrally locked screws and outer long, oblique screws may alleviate far cortex penetration, protecting nearby anatomical structures, and may ease implant removal and conversion to bicortical fixation for revision surgery; however, use of long oblique screws may increase the risk of early loosening under torsion.

BACKGROUND: Double-row rotator cuff tendon repair techniques may provide superior contact area and strength compared with single-row repairs, but are associated with higher material expenses and prolonged operating time. The purpose of this study was to evaluate gap formation, ultimate tensile strength and stiffness of a single-row cruciate suture rotator cuff repair construct, and to compare these results with those of the Mason-Allen and SutureBridge repair constructs. METHODS: Infraspinatus tendons from 24 spring lamb shoulders were harvested and allocated to cruciate suture, Mason-Allen and SutureBridge repair groups. Specimens were loaded cyclically between 10 and 62 N for 200 cycles, and gap formation simultaneously measured using a high-speed digital camera. Specimens were then loaded in uniaxial tension to failure, and construct stiffness and repair strength were evaluated. RESULTS: Gap formation in the cruciate suture repair was significantly lower than that of the Mason-Allen repair (mean difference = 0.6 mm, P = 0.009) and no different from that of the SutureBridge repair (P > 0.05). Both the cruciate suture repair (mean difference = 15.7 N/mm, P = 0.002) and SutureBridge repair (mean difference = 15.8 N/mm, P = 0.034) were significantly stiffer than that of the Mason-Allen repair; however, no significant differences in ultimate tensile strength between repair groups were discerned (P > 0.05). CONCLUSION: The cruciate suture repair construct, which may represent a simple and cost-effective alternative to double-row and double-row equivalent rotator cuff repairs, has comparable biomechanical strength and integrity with that of the SutureBridge repair, and may result in improved construct longevity and tendon healing compared with the Mason-Allen repair.

Isotropic hyperelastic models have been used to determine the material properties of normal human cartilage, but there remains an incomplete understanding of how these properties may be altered by osteoarthritis. The aims of this study were to (1) measure the material constants of normal and osteoarthritic human knee cartilage using isotropic hyperelastic models; (2) determine whether the material constants correlate with histological measures of structure and/or cartilage tissue damage; and (3) quantify the abilities of two common isotropic hyperelastic material models, the neo-Hookean and Yeoh models, to describe articular cartilage contact force, area, and pressure. Small osteochondral specimens of normal and osteoarthritic condition were retrieved from human cadaveric knees and from the knees of patients undergoing total knee arthroplasty and tested in unconfined compression at loading rates and large strains representative of weight-bearing activity. Articular surface contact area and lateral deformation were measured concurrently and specimen-specific finite element models then were used to determine the hyperelastic material constants. Structural parameters were measured using histological techniques while the severity of cartilage damage was quantified using the OARSI grading scale. The hyperelastic material constants correlated significantly with OARSI grade, indicating that the mechanical properties of cartilage for large strains change with tissue damage. The measurements of contact area described anisotropy of the tissue constituting the superficial zone. The Yeoh model described contact force and pressure more accurately than the neo-Hookean model, whereas both models under-predicted contact area and poorly described the anisotropy of cartilage within the superficial zone. These results identify the limits by which isotropic hyperelastic material models may be used to describe cartilage contact variables. This study provides novel data for the mechanica

Upper limb muscle force estimation using Hill-type muscle models depends on musculotendon parameter values, which cannot be readily measured non-invasively. Generic and scaled-generic parameters may be quickly and easily employed, but these approaches do not account for an individual subject's joint torque capacity. The objective of the present study was to develop a subject-specific experimental testing and modeling framework to evaluate shoulder muscle and joint function during activities of daily living, and to assess the capacity of generic and scaled-generic musculotendon parameters to predict muscle and joint function. Three-dimensional musculoskeletal models of the shoulders of 6 healthy subjects were developed to calculate muscle and glenohumeral joint loading during abduction, flexion, horizontal flexion, nose touching and reaching using subject-specific, scaled-generic and generic musculotendon parameters. Muscle and glenohumeral joint forces calculated using generic and scaled-generic models were significantly different to those of subject-specific models (p<0.05), and task dependent; however, scaled-generic model calculations of shoulder glenohumeral joint force demonstrated better agreement with those of subject-specific models during abduction and flexion. Muscles in generic musculoskeletal models operated further from the plateau of their force-length curves than those of scaled-generic and subject-specific models, while muscles in subject-specific models operated over a wider region of their force length curves than those of the generic or scaled-generic models, reflecting diversity of subject shoulder strength. The findings of this study suggest that generic and scaled-generic musculotendon parameters may not provide sufficient accuracy in prediction of shoulder muscle and joint loading when compared to models that employ subject-specific parameter-estimation approaches.

The management of irreparable rotator cuff tears associated with osteoarthritis of the glenohumeral joint has long been challenging. Reverse total shoulder arthroplasty (RSA) was designed to provide pain relief and improve shoulder function in patients with severe rotator cuff tear arthropathy. While this procedure has been known to reduce pain, improve strength and increase range of motion in shoulder elevation, scapular notching, rotation deficiency, early implant loosening and dislocation have attributed to complication rates as high as 62%. Patient selection, surgical approach and post-operative management are factors vital to successful outcome of RSA, with implant design and component positioning having a significant influence on the ability of the shoulder muscles to elevate, axially rotate and stabilise the humerus. Clinical and biomechanical studies have revealed that component design and placement affects the location of the joint centre of rotation and therefore the force-generating capacity of the muscles and overall joint mobility and stability. Furthermore, surgical technique has also been shown to have an important influence on clinical outcome of RSA, as it can affect intra-operative joint exposure as well as post-operative muscle function. This review discusses the behaviour of the shoulder after RSA and the influence of implant design, component positioning and surgical technique on post-operative joint function and clinical outcome.

We investigated the immediate effects of a varus knee brace on knee symptoms and knee-joint biomechanics in an individual with predominant lateral tibiofemoral joint osteoarthritis (TFJOA) and valgus malalignment after anterior cruciate ligament (ACL) reconstruction. A varus unloader brace was prescribed to a 48-year-old male with predominant lateral radiographic and symptomatic TFJOA and valgus malalignment eight-years following ACL reconstruction. During a step-down task, the participant rated knee pain, task-difficulty, knee-stability and knee-confidence on four separate visual analogue scales. Quantitative gait analysis was conducted during self-selected walking trials under three test conditions in a randomized order: (i) no brace; (ii) brace without frontal plane adjustment (no varus re-alignment); and (ii) brace with frontal plane adjustment (varus re-alignment). Post-processing of gait data involved calculation of knee kinematics and net joint moments for the reconstructed limb. The participant reported improved pain (3%), task difficulty (41%), stability (46%) and confidence (49%) when performing the step-down task with the brace. The varus brace resulted in immediate reductions in knee abduction angle (24%) and internal rotation angle (56%), and increased knee adduction moment (18%). These findings provide preliminary evidence for potentially beneficial effects of bracing on knee-symptoms and biomechanics in individuals with lateral TFJOA after reconstruction.