Search

Ceramic coatings were formed on the surface of as-cast Al5.2Zn1.7Mg0.4Ni0.3Fe and heat-treated Al7.0Zn2.7Mg0.5Ni0.4Fe "nikalin" aluminum alloys by using the plasma electrolytic oxidation (PEO) technique in a silicate–alkaline electrolyte. Uniform coatings containing a minimum number of defects and consisting predominantly of a γ-Al2O3 phase were synthesized on the surface of both Al-Zn-Mg-Ni-Fe alloys. The coatings had a microhardness of 660–1200 HV, which is 3.5–11 times higher than that of the "bare" as-cast and heat-treated alloy. The coating on the Al5.2Zn1.65Mg0.4Ni0.3Fe alloy had the highest peak hardness, which is probably caused by the lower residual alloying elements Zn and Mg in the coating bulk. As a consequence, the PEO coating with the highest hardness synthesized on the as-cast alloy exhibited a lower wear rate as compared to the heat-treated alloy. The polarization curves in 3.5% NaCl show that the PEO coatings in all cases reduced the corrosion current density and shifted the corrosion potential toward positive values, thus indicating protective properties of the coatings. The corrosion rate of the as-cast and heat-treated Al-Zn-Mg-Ni-Fe alloys increased noticeably by about 3.7–5.7 times after PEO treatment. A relationship between the residual alloying elements Zn and Mg in the bulk of the PEO coatings and corrosion resistance was established. [ABSTRACT FROM AUTHOR]

The compatibility of the wrought Al-Ca alloy with the element Fe was investigated in the present study. In this work, both the Al-Ca alloy and Al-Ca-Fe alloy were synthesized through melting, casting, heat treatment, and rolling. A new ternary Al-Ca-Fe eutectic phase, identified as Al10CaFe2 with an orthorhombic structure, demonstrated enhanced performance, as revealed by nanoindentation tests. Combining the results of the nanoindentation and EBSD, it can be inferred that during the rolling and heat treatment process, the divorced eutectic phases were broken and spheroidized, and the structure of the Fe-rich alloy became finer, which promotes the formation of fine grains during the process of dynamic recrystallization and effectively hindered the grain growth during thermal treatment. Consequently, the strength of the as-rolled Al-Ca alloy was improved with the addition of 1 wt.% Fe while the ductility of the alloy was maintained. Therefore, adding Ca into the high-Fe content recycled aluminum altered the form of the Fe-containing phases in the alloy, effectively expanding the application scope of recycled aluminum alloy manufacturing. This approach also offered a method for strengthening the Al-Ca aluminum alloys. Compared to the traditional approach of reducing Fe content in alloys through metallurgical means, this study opened a new avenue for designing novel, renewable aluminum alloys highly compatible with impurity iron in scrap. [ABSTRACT FROM AUTHOR]

The effects of Fe-bearing phases on the structure, mechanical properties, and fracture mechanism of a non-heat-treatable model sheet alloy (wt.%: Al–2%Cu–1.5%Mn(-Mg,Zn)), designed for Al20Cu2Mn3 dispersoids, was investigated. This involved a combination of thermodynamic modeling in the Thermo-Calc program and experimental studies of structure and mechanical properties. It has been shown that the addition of 0.5 and 0.4% iron and silicon leads to the formation of eutectic inclusions in the Al15(Mn,Fe)3Si2 phase. In addition to the Fe- bearing inclusions, the formation of the eutectic Al2Cu and Al2CuMg phases can be expected in the as-cast structure of the experimental alloys. Despite their relatively high fraction of eutectic particles, non-homogenized alloy ingots demonstrated sufficiently high deformation processability during the hot (400 °C) and cold rolling, which made it possible to obtain high-quality sheet alloys (with reduction degrees of 80 and 75%, respectively). The results of the tensile tests revealed that, after cold rolling, the addition of 1% Mg significantly increased the tensile and yield strengths, whereas the effect of 1% Zn was negligible. At the same time, the uniform distribution of Fe-bearing phases in the structure of the cold-rolled sheets contributes to the preservation of the dimple mechanism of the fracture toughness. This helps to maintain the same level of ductility for the cold-rolled sheet Fe-containing alloys as for Fe-free alloys. It has been shown, based on the data obtained, that adding Fe, Si, Mg, and Zn to the base Al–2%Cu–1.5%Mn alloy in a total amount of more than 3% makes it possible to retain the ductile fracture patterns of the base alloy and obtain a fairly higher level of mechanical properties. This suggests the fundamental possibility of using a variety of secondary raw materials (containing the main elements present in aluminum alloys of different alloying systems) to prepare a base alloy that does not require homogenization or thermal hardening. [ABSTRACT FROM AUTHOR]

This work was focused on studying the possibility of increasing the strength of non-heat-treatable sheet alloy Al2Cu1.5Mn (wt.%) by the joint addition of 1% Mg and 1% Zn. The effect of these elements on the structure and mechanical properties of the new sheet Al2Cu1.5Mn alloy designed for Al20Cu2Mn3 dispersoids has been studied by calculations and experimental methods. The obtained data on the phase composition, microstructure, and physical and mechanical properties of the new alloy for different processing routes (including hot rolling, cold rolling, and annealing) have been compared with those for the ternary Mg- and Zn-free alloy. It has been shown that the formation of nanosized Al20Cu2Mn3 dispersoids (~7 vol.%) provides for the preservation of the non-recrystallized grain structure after annealing at up to 400 °C (3 h), while Mg and Zn have a positive effect on the strength due to the formation of alloyed aluminum solid solution. As a result, cold-rolled sheets of the Al2Cu1.5Mn1Mg1Zn model alloy showed a substantially higher strength performance after annealing at 400 °C in comparison with the ternary reference alloy. In particular, the UTS is ~360 vs. ~300 MPa, and the YS is 280 vs. 230 MPa. For the example of the Al2Cu1.5Mn1Mg1Zn model alloy, it has been shown that the system is promising for designing new heat-resistant alloys as a sustainable alternative to the 2xxx alloys. The new alloy has an advantage over the commercial alloys (particularly, 2219, 2024, 2014), not only in manufacturability but also in thermal stability. The sheet production cycle for the model alloy is much shorter because the stages of homogenization, solution treatment, and water quenching are excluded. [ABSTRACT FROM AUTHOR]

Solidification path, hot tearing susceptibility and processability by L-PBF of the hypereutectic aluminium alloy Al-8%Zn-7%Ni-3%Mg were investigated. It was shown that the alloy has an advantageous hot tearing resistance due to formation of an adequate amount of the [(Al)+Al3Ni] eutectic and a reduced effective solidification range. In that sense, it may be valid for L-PBF. To prepare a feedstock for L-PBF, we produced chips which were subsequently grinded by high-energy ball milling into a 100 µm fine powder batch. The powder contained irregular shape particles that may have led to failure in fabrication of regular single tracks at a laser power of 170-250 W and scanning speed of 200-350 mm/s. Whilst from on-top view all the tracks had defects like balling and irregularity, their cross-sections also revealed a high degree of penetration into 5052 alloy substrate. Most structures showed a level of mixing of 5/1 between the substrate and the experimental alloy. The most successful track obtained at 250 W and 250 mm/s showed an inhomogeneity in distribution of the alloy-rich regions. Meanwhile, no defects and no primary Al3Ni phase were observed. The present study serves as an initial one for further research which may be focused on producing of a finer powder, assessment of different layer thicknesses and fabrication of bulk specimens.

The structure of the previously unstudied ternary Al-Ca-La system near the aluminum corner has been analyzed using experimental [scanning electron microscopy, electron microprobe analysis (EMPA), and x-ray diffraction analysis (XRD)] and computational analysis (thermodynamic calculations). Based on the experimental data, the projection of the liquidus surface and solid-state phase-field distribution of the ternary system have been suggested. It is shown that Al4(Ca,La) and Al11(La,Ca)3 compounds can be in equilibrium with aluminum. EMPA and XRD analyses have revealed significant mutual solubility between the binary Al4(Ca,La) and Al11(La,Ca)3 intermetallics which leads to significant changes in their structure and mechanical and physical properties. The analysis of hot tearing susceptibility together with linear contraction showed that new Al-(2–4)wt.%Ca-(0–2)wt.%La-1.5 wt.%Mn hypoeutectic quaternary alloys have excellent casting properties comparable to those of the most manufacturable casting branded aluminum alloys, e.g., A356 and 361. [ABSTRACT FROM AUTHOR]