Search

In this study, a practical study was conducted to compare the efficient behavior of close loop solar water heater with thermosiphon- riser tubes with dimensions (80 cm width, 120 cm height) with two acrylic covering. both with and without thermal performance enhancer, and to find the optimum mode of convection in the collector. the thermal performance enhancers have been used, helical spring with a core bar, and they were inserted a solar absorber tube The ethanol as a working fluid is used by applying a practical test set to it. The current tests were conducted on September 6, 8 and October 4, 5 , 2022, in Baghdad, Iraq, under identical ambient and load circumstances. All examination were from 08:00 am to 16:00 pm, at tilted angle (45 °) South in sunny days. The experimental tests were carried out at flow rates (1 and 1.5 L/min) and filling ratio (50%). At a flow rate of 1.5 L/min and a filling ratio of 50%, using an inserted helical spring with a core bar yielded the highest daily efficiency of 70%. In the interest of the system.

Thermoelectric coolers (TEC) are devices that conversion of electrical power into a temperature gradient. TEC modules have the benefits of high dependability, small dimensions, lightweight, absence of mechanical moving parts and working fluid. Thermoelectric cooling systems have experienced significant utilisation in recent years. These technologies have been used in automobiles to cool and maintain the quality of goods during transportation and in portable cooling bags, computers, and medical apparatus. The TEC manufacture datasheet only offers limited data on characteristics and maximum parameters, which is insufficient for studying thermoelectric systems. This paper presents an analytical modelling methodology that provides a direct method for assessing the performance of module parameters and determining the fundamental thermal physical parameters of a TEC. Furthermore, this article outlines the procedure for choosing the appropriate TEC module from a selection of three options to integrate it with a vapour compression refrigeration (VCR) system. The objective is to attain low temperatures while reducing power consumption and improving performance. The findings indicates that The TEC1-12706 module was the most suitable option among three different types of TEC modules for integration with the VCR system to achieve low temperatures. This choice was based on its lower power consumption than the TEC127010 and TEC127015 modules, resulting in 36.5% and 59.3% energy savings, respectively. Additionally, the heat dissipation from the hot side of the TEC12706 is lower than the TEC12710 and TEC12715 modules by 32.2% and 59%, respectively.

In this study, a different design of passive air Solar Chimney(SC)was tested by installing it in the south wall of insulated test room in Baghdad city. The SC was designed from vertical and inclined parts connected serially together, the vertical SC (first part) has a single pass and Thermal Energy Storage Box Collector (TESB (refined paraffin wax as Phase Change Material(PCM)-Copper Foam Matrix(CFM))), while the inclined SC was designed in single pass, double passes and double pass with TESB (semi refined paraffin wax with copper foam matrix) with selective working angle ((30o, 45o and 60o). A computational model was employed and solved by Finite Volume Method (FVM) to simulate the air induced through the test room by SC effect. The governing equation of Computational Fluid Dynamic (CFD) model was developed by the effective heat capacity method equation to describe the heat storage and release from PCM-CFM. Practical and computational Results referred to increase in thermal conductivity of the paraffin wax that supported by CFM than 10 times, while the ventilation effect is still active for hours after sun set amount. The maximum ventilation mass flow rate with TESB collector was 36.651 kg/hr., when the overall discharge coefficient equals 0.371. Also, the experimental results referred to the best working angle range 45~60o, while the highest approaching temperature (between air and collector) was appeared for the double passes flat plate collector. Results gave higher heat storage efficiency 47% when the maximum solar radiation 780 W/m2 at 12.00 pm, and the energy summation through duration of charging time was 18460 kJ. Double passes SC at 60o angle presented the highest efficiency with value approaching to 73%, while TESB collector efficiency depicted highest efficiency value 70% at 12:00 pm.

A paraffin wax and copper foam matrix were used as a thermal energy storage material in the double passes air solar chimney (SC) collector to get ventilation effect through daytime and after sunset. Air SC collector was installed in the south wall of an insulated test room and tested with different working angles (30o, 45o and 60o). Different SC types were used; single pass, double passes flat plate collector and double pass thermal energy storage box collector (TESB). A computational model based on the finite volume method for transient tw dimensional domains was carried out to describe the heat transfer and storage in the thermal energy storage material of collector. Also, equivalent specific heat method was employed to describe the heat storage and release in the mushy zone. Experimental results referred to an increase in thermal conductivity of paraffin wax that supported by copper foam matrix more than ten times. While the ventilation effect was still active for hours after the sun set, depending on the heat storage amount. Maximum ventilation mass flow rate with TESB collector was recorded with value equals to 36.651 kg/hr., when the overall discharge coefficient that was calculated for the system equals to 0.371. Experimental results showed that the best working angle range was 45~60o, and the highest air to the collector approaching temperature appeared to the double passes flat plate collector. Results gave greater heat storage efficiency of (47)% when the maximum solar radiation was 780 W/m2 at 12.00pm, while the energy summation through duration charge time was 18460 kJ. Computational results, depending on the equivalent heat capacity method for heat storage or release from phase change material that supported by copper foam matrix, showed the behavior of paraffin wax melting and solidification situation through periodic for charge and released heat from the solar collector. Also, these results gave agreement approaching the experimental results for the heat storage in the combined heat storage material, with standard error of 16.8%.

In this work, a test room was built in Baghdad city, with selective dimensions, while the solar chimneys (SC) where designed with aspect ratio (ar) bigger than 12 and setup to the oriented wall to the south. Collector of SC consist of paraffin wax as a phase change material (PCM) and supported by copper foam matrix (CFM), to enhance the combined of thermal energy storage material box (TESMB). Double transparent acrylic sheets covered the collector from outside. TESB supported by array of evacuated tubular collector with thermosyphon to sincere heat storage in the TESB. Results of experimental work that achieved in 25 January and 26 February refer to effectiveness using TESM in closed loop SC in day time and its effect cover the night time also. The heating system of test room is arrived to the biggest room temperature after sun set, at that moment the difference between indoor and outdoor approximately 15oC, and room temperature value still bigger after five hours from sun- set with a different in temperature by approximately 8 oC. Numerical solution done by employing CFD with solution the PDE’s that present continuity, momentum, energy equations, by using the FVM with algebraic forms of turbulent viscosity and diffusion coefficient and employing turbulent standard (k-ε)model. The comparison between numerical and experimental results indicated that the heat transfer inside test room is dominate by condition, also results shows acceptable convergence in velocity and temperature profile, while the experimental results for air flow inside SC gap appears the turbulent behavior in most duration time.

In this work, a test room was built in Baghdad city, with (2*1.5*1.5) m3 in dimensions, while the solar chimneys (SC) were designed with aspect ratio (ar) bigger than 12. Test room was supplied by many solar collectors; vertical single side of air pass with ar equals 25, and tilted 45o double side of air passes with ar equals 50 for each pass, both collectors consist of flat thermal energy storage box collector (TESB) that covered by transparent clear acrylic sheet, third type of collector is array of evacuated tubular collectors with thermosyphon in 45o instelled in the bottom of TESB of vertical SC. The TESB was made from metallic iron sheets as a shell and fuelled by paraffin wax as phase change material (PCM). The PCM supported by copper foam matrix (CFM) to enhance thermal conductivity of wax. When heat is released from TESB to the air, a buoyancy force will be generated in chimney gaps. Then a difference in pressure between inside and outside test room leads to induce the air flow to test room through wet corrugated cellulose pad, where evaporative cooling (EC) occurs. Results of experimental work, that achieved in June, for 12 to24 hour in the test day, refer to effectiveness using EC to decrease the room temperature comparing. The system reduces test room temperature of up to 8.5~9.2 oC in 11:00 am to 3:00 pm and at highest effectiveness of EC, while minimum reduces in temperature of up to 3.5 oC in 8:00pm to 3:00 am. Also, the results showed the affectivity to using the TESB, during the night time for ventilation and EC, with lower effectiveness than from day time. The range of EC effectiveness equals 30.5-37.5 with a natural vent, while The maximum air change per hour (ACH) equals (3.8-6.187), and the maximum mass flow rate is equal to (36.651 kg.hr-1) at experimental evaluation of the system’s discharge coefficient value 0.371.

In this work, a test room was built in Baghdad city, with (2*1.5*1.5) m3 in dimensions, while the solar chimneys (SC) were designed with aspect ratio (ar) bigger than 12. Test room was supplied by many solar collectors; vertical single side of air pass with ar equals 25, and tilted 45o double side of air passes with ar equals 50 for each pass, both collectors consist of flat thermal energy storage box collector (TESB) that covered by transparent clear acrylic sheet, third type of collector is array of evacuated tubular collectors with thermosyphon in 45o instelled in the bottom of TESB of vertical SC. The TESB was made from metallic iron sheets as a shell and fuelled by paraffin wax as phase change material (PCM). The PCM supported by copper foam matrix (CFM) to enhance thermal conductivity of wax. When heat is released from TESB to the air, a buoyancy force will be generated in chimney gaps. Then a difference in pressure between inside and outside test room leads to induce the air flow to test room through wet corrugated cellulose pad, where evaporative cooling (EC) occurs. Results of experimental work, that achieved in June, for 12 to24 hour in the test day, refer to effectiveness using EC to decrease the room temperature comparing. The system reduces test room temperature of up to 8.5~9.2 oC in 11:00 am to 3:00 pm and at highest effectiveness of EC, while minimum reduces in temperature of up to 3.5 oC in 8:00pm to 3:00 am. Also, the results showed the affectivity to using the TESB, during the night time for ventilation and EC, with lower effectiveness than from day time. The range of EC effectiveness equals 30.5-37.5 with a natural vent, while The maximum air change per hour (ACH) equals (3.8-6.187), and the maximum mass flow rate is equal to (36.651 kg.hr-1) at experimental evaluation of the system’s discharge coefficient value 0.371.