Search

Au nanoparticles at the TiO$_2$ surface can enhance the photocatalytic H$_2$ generation performances owing to their electron transfer co-catalytic ability. Key to maximize the co-catalytic effect is a fine control over Au nanoparticle size and placement on the photocatalyst, in relation to parameters such as the TiO$_2$ morphology, illumination wavelength and pathway, and light penetration depth in the photocatalyst. Here we present an approach for site-selective intrinsic-decoration of anodic TiO$_2$ nanotubes (TNs) with Au nanoparticles: we produce, by Ti and Au co-sputtering, Ti-Au alloy layers that feature compositional gradients across their thickness; these layers, when anodized under self-ordering electrochemical conditions, can form Au-decorated TNs where the Au nanoparticle density and placement vary according to the Au concentration profile in the metal alloy substrates. Our results suggest that, the Au co-catalyst placement strongly affects the photocatalytic H$_2$ evolution performance of the TNs layers. We demonstrate that, when growing Au-decorated TNs, the use of Ti-Au substrates with a suitable Au compositional gradient can lead to higher H$_2$ evolution rates compared to TNs classically grown with a homogenous co-catalyst decoration. As a side effect, a proper placement of the co-catalyst nanoparticles allows for reducing the amount of noble metal without dumping the H$_2$ evolution activity.

Self-standing TiO$_2$ nanotube layers in the form of membranes are fabricated by self-organizing anodization of Ti metal and a potential shock technique. The membranes were then decorated by sputtering different Pt amounts i) only at the top, ii) only at the bottom or iii) at both top and bottom of the tube layers. The Pt-decorated membranes are transferred either in tube top up or in tube top down configuration onto FTO slides and investigated after crystallization as photocatalysts for H$_2$ generation using either front or back-side light irradiation. Double-side Pt-decoration of the tube membranes leads to higher H$_2$ generation rates (independent of tube and light irradiation configuration) compared to membranes decorated at only one side with similar overall Pt amounts. The results suggest that this effect is not ascribed to the overall amount of Pt cocatalyst as such but rather to its distribution at both tube extremities. This leads to optimized light absorption and electron diffusion/transfer dynamics: the central part of the membranes act as light harvesting zone and electrons therein generated can diffuse towards the Pt/TiO$_2$ active zones (tube extremities) where they can react with the environment and generate H$_2$ gas.

Gold-decorated TiO$_2$ nanotubes were used for the photocatalytic abatement of Hg(II) in aqueous solutions. The presence of dewetted Au nanoparticles induces a strong enhancement of photocatalytic reduction and scavenging performances, with respect to naked TiO$_2$. In the presence of chlorides, a massive formation of Hg2Cl2 nanowires, produced from Au nanoparticles, was observed using highly Au loaded photocatalysts to treat a 10 ppm Hg(II) solution. EDS and XPS confirmed the nature of the photo-produced nanowires. In the absence of chlorides and/or at lower Hg(II) starting concentrations, the scavenging of mercury proceeds through the formation of Hg-Au amalgams. Solar light driven Hg(II) abatements up to 90% were observed after 24h. ICP-MS analysis revealed that the removed Hg(II) is accumulated on the photocatalyst surface. Regeneration of Hg-loaded exhaust photocatalysts was easily performed by anodic stripping of Hg(0) and Hg(I) to Hg(II). After four catalytic-regeneration cycles only a 10% decrease of activity was observed.

Flat TiO$_2$ layers are deposited by magnetron sputtering on Ti/Si wafers. The TiO$_2$ surfaces are then sputter-coated with thin Au films of a nominal thickness of 0.5-10 nm that are converted by solid-state dewetting into Au nanoparticles of tuneable size and spacing; the Au nanoparticle size can be tuned over a broad range, i.e. ca. 3-200 nm. The Au-decorated TiO$_2$ surfaces enable plasmonic photo-electrochemical water splitting under visible light illumination (450-750 nm). The water splitting performance reaches a maximum for TiO$_2$ layers decorated with ~ 30 nm-sized Au particles. As expected, optical absorption measurements show a red shift of the plasmonic extinction band with increasing the Au nanoparticle size. However, the plasmonic photocurrent is found to peak at ~ 600 nm regardless of the size of the Au nanoparticles, i.e. the plasmonic photocurrent band position is size-independent. Such a remarkable observation can be ascribed to a hot electron injection cut-off effect.

Photocatalytic $H_2$ evolution reactions on pristine TiO$_2$ is characterized by low efficiencies due to trapping and recombination of charge carriers, and due to a sluggish kinetics of electron transfer. Noble metal (mainly Pt, Pd, Au) nanoparticles are typically decorated as cocatalyst on the TiO$_2$ surface to reach reasonable photocatalytic yields. However, owing to the high cost of noble metals, alternative metal cocatalysts are being developed. Here we introduce an approach to fabricate an efficient noble metal free photocatalytic platform for $H_2$ evolution based on alloyed NiCu cocatalytic nanoparticles at the surface of anodic TiO$_2$ nanotube arrays. NiCu bilayers are deposited onto the TiO$_2$ nanotubes by plasma sputtering. A subsequent thermal treatment is carried out that leads to dewetting, that is, owing to surface diffusion the Ni and Cu sputtered layers simultaneously mix with each other and split into NiCu nanoparticles at the nanotube surface. The approach allows for a full control over key features of the alloyed nanoparticles such as their composition, work function and cocatalytic ability towards $H_2$ generation. Dewetted-alloyed cocatalytic nanoparticles composed of equal Ni and Cu amounts not only are significantly more reactive than pure Ni or Cu nanoparticles, but also lead to $H_2$ generation rates that can be comparable to those obtained by conventional noble metal (Pt) decoration of TiO$_2$ nanotube arrays.

In the present work we explore the front- and back-side performance of a photocatalytic platform consisting of self-organized TiO2 nanotube layers formed by complete anodization of Ti metal films evaporated on quartz slides. The adhesion and light transmission of the tube layers on the quartz surfaces are optimized by a suitable anodization procedure. After their growth, the nanotube arrays were converted into crystalline structures and sputter-coated with co-catalytic Pt nanoparticles. The optically transparent quartz substrates enable the use of the Pt-decorated tube layers for photocatalytic H2 generation under either front- or back-side illumination configurations. The nanotube films on quartz are characterized in view of their physico-chemical properties, including their light transmission features measured using different light sources. The results show that the front-side illumination under optimized factors, i.e., the amount of loaded co-catalyst, yields a maximized photocatalytic performance in terms of H2 generation.

In the present work we use TiO2 nanotube arrays, carrying a Pt coating that is optimally dewetted, as a photocatalyst to generate H2. In order to achieve a maximum H2-generation efficiency, on the one hand an ideal thermal dewetting of the Pt layer into nanoparticles is needed that requires an oxygen free heat treatment, and on the other hand an optimal crystallization of the TiO2 nanotubes into anatase with reduced defect density is achieved only by annealing in O2 containing environment. To overcome this issue, we combine adequate reducing and oxidizing conditions in a multiple annealing treatment, and obtain Pt-decorated anatase TiO2 nanotubes showing significantly enhanced photocatalytic H2 generation ability.

TiO2 nanotube arrays grown by anodization were coated with thin layers of polydopamine as visible light sensitizer. The PDA-coated TiO2 scaffolds were used as photocatalyst for selective oxidation of benzyl alcohol under monochromatic irradiation at 473 nm. Benzaldehyde was selectively formed and no by-products could be detected. A maximized reaction yield was obtained in O2-saturated acetonitrile. A mechanism is proposed that implies firstly the charge carrier generation in polydopamine as a consequence of visible light absorption. Secondly, photo-promoted electrons are injected in TiO2 conduction band, and subsequently transferred to dissolved O2 to form oxygen radical anions. These radicals react with benzyl alcohol and lead to its selective dehydrogenation oxidation towards benzaldehyde.

We fabricate photo-anodes by transferring anodic TiO2 nanotube membranes in tube-top-down configuration on FTO glass, and use them for constructing frontside illuminated dye-sensitized solar cells. Prior to solar cell construction, the tube-based photo-anodes are crystallized at different temperatures (400-800{\deg}C), and the effects of tube electron transport properties on the photovoltaic performance of the solar cells are investigated. We show that improved solar cell efficiencies (up to ca. 8.0%) can be reached by high-temperature treatment of the tube membranes. Consistently with electron transport time measurements, remarkably enhanced electron mobility is enabled when tube membranes are crystallized at 600{\deg}C., Comment: Published 1 October 2015, 2016 IOP Publishing Ltd, Semiconductor Science and Technology, Volume 31, Number 1

We introduce the use of pure molten ortho-phosphoric acid (o-H3PO4) as an electrolyte for selforganizing electrochemistry. This electrolyte allows for the formation of self-organized oxide architectures (one-dimensional nanotubes, nanochannels, nanopores) on metals such as tungsten that up to now were regarded as very difficult to grow self-ordered anodic oxide structures. In this work, we show particularly the fabrication of thick, vertically aligned tungsten oxide nanochannel layers, with pore diameter of ca. 10 nm, and illustrate their potential use in some typical applications.

We optimize the deposition of CH3NH3PbI3 perovskite into mesoporous electrodes consisting of anodic TiO2 nanotube layers. By a simple spin coating approach, complete filling of the tube scaffolds is obtained, that leads to interdigitated perovskite structures in conformal contact with the TiO2 tube counterparts. Such assemblies can be used as solid state solar cells in hole-transporting material-free configuration, i.e., the tube scaffold serves as electron collector and blocking layer, while the perovskite acts as visible light absorber and hole transporting material. We show that the complete filling of the tube scaffold with the perovskite is essential to improve the solar cell efficiency.

In the present work we investigate various optical properties (such as light absorption and reflectance) of anodic TiO2 nanotubes layers directly transferred as self-standing membranes onto quartz substrates. This allows investigation in a transmission geometry which provides significantly more reliable data than measurements on the metallic Ti substrate. Light transmission and reflectance measurements were carried out for layers of thicknesses varying from 1.8 to 50 micrometer, and the layers were investigated in their amorphous and crystalline form. A series of wavelength-dependent light attenuation coefficients are extrapolated and found to match the photocurrent vs. irradiation wavelength behavior. However, a feature specific to anodic nanotubes is that their intrinsic carbon content causes a sub-bandgap response that is proportional to the carbon contamination content in the TiO2 nanotubes. Overall the extracted data provide valuable basis and understanding for the design of photo-electrochemical devices based on TiO2 nanotubes.

In the present work we compare TiO2 nanotube lift-off strategies for the construction of front-side illuminated dye-sensitized solar cells (DSSCs). Anodic nanotube layers were detached from the metallic back contact by using different techniques and transferred onto an FTO substrate. We show that if we use an optimized potential step treatment to fabricate membranes, DSSC cell efficiencies can be significantly increased (>8%). This improved efficiency is ascribed to higher specific dye-loading and enhanced electron transport properties of optimally fabricated TiO2 nanotube membranes.

In the present work we introduce a technique to form a photocatalyst, based on Pt nanoparticles suspended over the mouth of TiO2 nanotubes. These structures are obtained by the decoration of the top end of highly ordered TiO2 nanotubes with a web of TiO2 nanofibrils, followed by sputter deposition of a minimum amount of Pt. A subsequent thermal dewetting step forms 3-6 nm-sized Pt nanoparticles along the nanofibrils. These structures, when compared to conventional Pt decoration techniques of TiO2 nanotubes, show a strongly enhanced photocatalytic H2 evolution efficiency.

The least is the best. We introduce a technique to strongly reduce Pt use for photocatalytic hydrogen generation from TiO2 nanotubes. By site-selectively depositing thin layers of Pt only at the mouth of the nanotubes and by a subsequent thermal dewetting step, we achieve an outstanding photocatalytic improvement with minimal amounts of co-catalyst.

Overlaid self-ordering processes: we form anodic self-organized TiO2 nanostumps and exploit them for self-ordering dewetting of Au-Ag sputtered films. This forms ordered particle configurations at tube top (crown position) or bottom (ground position). By dealloying we then form, from minimal amount of noble metal, porous Au nanoparticles that when in crown position allow for a drastically improved photocatalytic H2 production compared with nanoparticles produced by conventional dewetting processes.