Search

Octyl-silane-coated Al2O3 nanoparticles are found to be a promising conductivity-reducing additive for thermoplastic ternary blends comprising low-density polyethylene (LDPE), isotactic polypropylene and a styrenic copolymer.

Click chemistry type reactions between polyethylene-based copolymers are a promising and by-product free alternative to peroxide crosslinking of low-density polyethylene, which is widely used as an insulation material for high-voltage power cables.

The impact of a small amount of polystyrene-b-poly(ethylene-co-butylene)-b-polystyrene (SEBS) on the thermomechanical and electrical properties of blends comprising low-density polyethylene (LDPE) and isotactic polypropylene (PP) is investigated. SEBS is found to assemble at the PP:LDPE interface as well as within isolated PP domains. The addition of 10 wt% SEBS significantly increases the storage modulus between the melting temperatures of the two polyolefins, 110 and 160°C, and results in improved resistance to creep during both tensile deformation as well as compression. Furthermore, the ternary blends display a very low direct-current (DC) conductivity as low as 3.4 × 10 S m at 70°C and 30 kV mm , which is considerably lower than values measured for neat LDPE. The here presented type of ternary blend shows potential as an insulation material for high-voltage direct current power cables.

The most common type of extruded power cable insulation is based on cross-linked polyethylene (XLPE), which cannot be recycled as a thermoplastic material. Hence, thermoplastic insulation materials...

High-voltage direct-current power cables are vital for the efficient transport of electricity derived from renewable sources of energy. The most widely used material for high-voltage power cable insulation - low-density polyethylene (LDPE) - is usually crosslinked with peroxides, a process that releases unwanted by-products. Hence, by-product-free crosslinking concepts that mitigate the associated increase in electrical conductivity are in high demand. Click chemistry-type crosslinking of polyethylene copolymer mixtures that contain glycidyl methacrylate and acrylic acid co-monomers is a promising alternative, provided that the curing reaction can be controlled. Here, we demonstrate that the rate of the curing reaction can be adjusted by tuning the number of epoxy and carboxyl groups. Both dilution of copolymer mixtures with neat LDPE and the selection of copolymers with a lower co-monomer content have an equivalent effect on the curing speed. Ternary blends that contain 50 wt% of neat LDPE feature an extended extrusion window of up to 170 degrees C. Instead, at 200 degrees C rapid curing is possible, leading to thermosets with a low direct-current electrical conductivity of about 10(-16) S cm(-1) at an electric field of 20 kV mm(-1) and 70 degrees C. The conductivity of the blends explored here is comparable to or even lower than values measured for both ultraclean LDPE and a peroxide-cured commercial crosslinked polyethylene grade. Hence, click chemistry curing represents a promising alternative to radical crosslinking with peroxides. (c) 2019 Society of Chemical Industry

Self-propelled micromachines have recently attracted attention for environmental remediation, yet their use for radioactive waste management has not been addressed. Engineered micromotors that are able to combine highly adsorptive capabilities together with fast autonomous motion in liquid media are promising tools for the removal of nuclear waste, which is one of the most difficult types to manage. Herein, we fabricate self-propelled micromotors based on metal-organic frameworks (MOFs) via template-based interfacial synthesis and show their potential for efficient removal of radioactive uranium. A crucial challenge of the MOF-based motors is their stability in the presence of fuel (hydrogen peroxide) and acidic media. We have ensured their structural stability by Fe doping of zeolitic imidazolate framework-8 (ZIF-8). The implementation of magnetic ferroferric oxide nanoparticles (Fe3O4 NPs) and catalytic platinum nanoparticles (Pt NPs) results in the magnetically responsive and bubble-propelled micromotors. In the presence of 5 wt % H2O2, these micromotors are propelled at a high speed of ca. 860 ± 230 μm·s-1 (i.e., >60 body lengths per second), which is significantly faster than that of other microrod-based motors in the literature. These micromotors demonstrate a highly efficient removal of uranium (96%) from aqueous solution within 1 h, with the subsequent recovery under magnetic control, as well as stable recycling ability and high selectivity. Such self-propelled magnetically recoverable micromotors could find a role in the management and remediation of radioactive waste.

The development of highly sensitive sensors and power generators that could function efficiently in extreme temperatures and contact with fire can be lifesaving but challenging to accomplish. Herein, we report, for the first time, a fire-retardant and self-extinguishing triboelectric nanogenerator (FRTENG), which can be utilized as a motion sensor and/or power generator in occupations such as oil drilling, firefighting or working in extreme temperature environments with flammable and combustible materials. The device takes advantage of the excellent thermal properties of carbon derived from resorcinol-formaldehyde aerogel whose electrical, mechanical and triboelectric properties have been improved via the introduction of Polyacrylonitrile nanofibers and graphene oxide nanosheets. This FRTENG is not flammable even after 90 s of trying, whereas conventional triboelectric materials were entirely consumed by fire under the same conditions. The developed device shows exceptional charge transfer characteristics, leading to a potential difference up to 80 V and a current density up to 25 µA/m2. When integrated into firefighter's shoes, the FRTENG is able to discern the movements of a firefighter in hazardous situations, while providing the high thermal stability missing in conventional TENGs. The fire-retardant and self-extinguishing characteristics offered by the FRTENG makes it a path-breaking device for lifesaving wearable applications.

Poly(3-hexylthiophene) (P3HT) is found to be a highly effective conductivity-reducing additive for low-density polyethylene (LDPE), which introduces a new application area to the field of conjugated polymers. Additives that reduce the direct-current (DC) electrical conductivity of an insulation material at high electric fields have gained a lot of research interest because they may facilitate the design of more efficient high-voltage direct-current power cables. An ultralow concentration of regio-regular P3HT of 0.0005 wt% is found to reduce the DC conductivity of LDPE threefold, which translates into the highest efficiency reported for any conductivity-reducing additive to date. The here-established approach, i.e., the use of a conjugated polymer as a mere additive, may boost demand in absolute terms beyond the quantities needed for thin-film electronics, which would turn organic semiconductors from a niche product into commodity chemicals.

Hydrogen (H2) sensors that can be produced en masse with cost-effective manufacturing tools are critical for enabling safety in the emerging hydrogen economy. The use of melt-processed nanocomposites in this context would allow the combination of the advantages of plasmonic hydrogen detection with polymer technology; an approach which is held back by the slow diffusion of H2 through the polymer matrix. Here, we show that the use of an amorphous fluorinated polymer, compounded with colloidal Pd nanoparticles prepared by highly scalable continuous flow synthesis, results in nanocomposites that display a high H2 diffusion coefficient in the order of 10-5 cm2 s-1. As a result, plasmonic optical hydrogen detection with melt-pressed fluorinated polymer nanocomposites is no longer limited by the diffusion of the H2 analyte to the Pd nanoparticle transducer elements, despite a thickness of up to 100 μm, thereby enabling response times as short as 2.5 s at 100 mbar (≡10 vol. %) H2. Evidently, plasmonic sensors with a fast response time can be fabricated with thick, melt-processed nanocomposites, which paves the way for a new generation of robust H2 sensors.

Knowledge of the electrical conductivity of polymer insulation materials is important for designing cable components for high-voltage direct-current (HVDC) applications. The aim of this study is to compare three measuring techniques, namely, charging current, surface potential decay (SPD) and dielectric response measurements. The first method is time consuming because it requires that the current through a material is recorded while a direct-current (DC) voltage is applied for a prolonged period of time. The DC conductivity is calculated from the steady state current, which is typically only approached after several hours to days. In SPD experiments, the decay of a potential, induced by corona charging, is monitored and utilized to estimate the field-dependent conductivity from one single measurement. Frequency domain dielectric spectroscopy (FDS) measurements allow to estimate the DC conductivity from the low frequency response. Two materials, low density polyethylene (LDPE) and cross-linked polyethylene (XLPE), were used. The SPD measurements overestimated the conductivities of both materials compared to those obtained by the charging current method for the entire studied range of temperature (30-70° C) and electric field (10–50 kV/mm). At the same, FDS measurements underestimated the temperature dependency of the conductivity for both LDPE and XLPE. It was noticed that the SPD technique demonstrated a very good repeatability and required significantly shorter measuring time compared to other methods.

MXenes show differential affinity towards single- and double-stranded DNA, with unique kinetics and potential for fluorescent biosensing., The integration of nucleic acids with nanomaterials has attracted great attention from various research communities in search of new nanoscale tools for a range of applications, from electronics to biomedical uses. MXenes are a new class of multielement 2D materials baring exciting properties mostly directed to energy-related fields. These advanced materials are now beginning to enter the biomedical field given their biocompatibility, hydrophilicity and near-infrared absorption. Herein, we elucidate the interaction of MXene Ti3C2Tx with fluorophore-tagged DNA by fluorescence measurements and molecular dynamics simulations. The system showed potential for biosensing with unequivocal detection at picomole levels and single-base discrimination. We found that this material possesses a kinetically unique entrapment/release behavior, with potential implications in time-controlled biomolecule delivery. Our findings present MXenes as platforms for binding nucleic acids, contributing to their potential for hybridization-based biosensing and related bio-applications.

To design reliable high voltage cables, clean materials with superior insulating properties capable of operating at high electric field levels at elevated temperatures are required. This study aims at the electrical characterization of a byproduct-free crosslinked copolymer blend, which is seen as a promising alternative to conventional peroxide crosslinked polyethylene currently used for high voltage direct current cable insulation. The characterization entails direct current (DC) conductivity, dielectric response and surface potential decay measurements at different temperatures and electric field levels. In order to quantify the insulating performance of the new material, the electrical properties of the copolymer blend are compared with those of two reference materials, i.e., low-density polyethylene (LDPE) and peroxide crosslinked polyethylene (XLPE). It is found that, for electric fields of 10–50 kV/mm and temperatures varying from 30 °C to 70 °C, the DC conductivity of the copolymer blend is in the range of 10−17–10−13 S/m, which is close to the conductivity of crosslinked polyethylene. Furthermore, the loss tangent of the copolymer blend is about three to four times lower than that of crosslinked polyethylene and its magnitude is on the level of 0.01 at 50 °C and 0.12 at 70 °C (measured at 0.1 mHz and 6.66 kV/mm). The apparent conductivity and trap density distributions deduced from surface potential decay measurements also confirmed that the new material has electrical properties at least as good as currently used insulation materials based on XLPE (not byproduct-free). Thus, the proposed byproduct-free crosslinked copolymer blend has a high potential as a prospective insulation medium for extruded high voltage DC cables.

Self-motile mesoporous ZnO/Pt-based Janus micromotors accelerated by bubble propulsion that provide efficient removal of explosives and dye pollutants via photodegradation under visible light are presented. Decomposition of H2O2 (the fuel) is triggered by a platinum catalytic layer asymmetrically deposited on the nanosheets of the hierarchical and mesoporous ZnO microparticles. The size-dependent motion behavior of the mesoporous micromotors is studied; the micromotors with average size ∼1.5 μm exhibit enhanced self-diffusiophoretic motion, whereas the fast bubble propulsion is detected for micromotors larger than 5 μm. The bubble-propelled mesoporous ZnO/Pt Janus micromotors show remarkable speeds of over 350 μm s-1 at H2O2 concentrations lower than 5 wt %, which is unusual for Janus micromotors based on dense materials such as ZnO. This high speed is related to efficient bubble nucleation, pinning, and growth due to the highly active and rough surface area of these micromotors, whereas the ZnO/Pt particles with a smooth surface and low surface area are motionless. We discovered new atomic interfaces of ZnO2 introduced into the ZnO/Pt micromotor system, as revealed by X-ray diffraction (XRD), which contribute to enhance their photocatalytic activity under visible light. Such coupling of the rapid movement with the high catalytic performance of ZnO/Pt Janus micromotors provides efficient removal of nitroaromatic explosives and dye pollutants from contaminated water under visible light without the need for UV irradiation. This paves the way for real-world environmental remediation efforts using microrobots.

The incorporation of metal oxide (e.g. Al2O3) nanoparticles has a pronounced positive effect on low-density polyethylene (LDPE) as an insulating material for high-voltage direct-current (HVDC) cabl ...

The degradation of fluoroelastomers (FKM) based on different monomers, additives and curing systems was studied after exposure to rapeseed biodiesel at 100 °C and different oxygen partial pressures ...

Self-propelled micromachines have recently attracted attention for environmental remediation, yet their use for radioactive waste management has not been addressed. Engineered micromotors that are able to combine highly adsorptive capabilities together with fast autonomous motion in liquid media are promising tools for the removal of nuclear waste, which is one of the most difficult types to manage. Herein, we fabricate self-propelled micromotors based on metal-organic frameworks (MOFs)

Self-propelled micromachines have recently attracted lots of attention for environmental remediation. Developing a large-scale but template-free fabrication of self-propelled rod/tubular micro/nanomotors is very crucial but still challenging. Here, a new strategy based on vertically aligned ZnO arrays is employed for the large-scale and template-free fabrication of self-propelled ZnO-based micromotors with H2 O2 -free light-driven propulsion ability. Brush-shaped ZnO-based micromotors with different diameters and lengths are fully studied, which present a fast response to multicycles UV light on/off switches with different interval times (2/5 s) in pure water and slow directional motion in aqueous hydrogen peroxide solution in the absence of UV light. Light-induced electrophoretic and self-diffusiophoretic effects are responsible for these two different self-motion behaviors under different conditions, respectively. In addition, the pH of the media and the presence of H2 O2 show important effects on the motion behavior and microstructure of the ZnO-based micromotors. Finally, these novel ZnO-based brush-shaped micromotors are demonstrated in a proof-of-concept study on nitroaromatic explosive degradation, i.e., picric acid. This work opens a completely new avenue for the template-free fabrication of brush-shaped light-responsive micromotors on a large scale based on vertically aligned ZnO arrays.

The electric conduction under intense electric fields (up to ∼ 109 V/m) in nanofluids using surface-modified ZnO–C18 nanoparticles dispersed in mineral oil as host, is investigated with both experiments and numerical simulations. The measurements are used to estimate unknown parameters necessary to represent the generation and loss of electrons in an electrohydrodynamic model for mineral oil with and without ZnO–C18 nanoparticles in a needle-plane configuration. The model suggests that ZnO–C18 nanoparticles induce an enhanced field emission from negative needles, explaining the significantly larger conduction currents measured in the nanofluid compared with those in the host liquid. It is also found that the scavenging of electrons by ZnO–C18 nanoparticles is a process which is negligible compared with the loss of electrons due to attachment in mineral oil. It is shown that ZnO–C18 nanoparticles hinder the streamer initiation process by reducing the effective electric field at the tip of the needle. This electric field reduction is caused by the combined effect of enhanced electron injection through ZnO–C18 nanoparticles and strong electron attachment in mineral oil. Thus, the electric field on the needle tip reaches the same threshold value when the streamer is incepted in the nanofluid as in mineral oil, although at a larger voltage. Solid evidence indicating that the additional electron scavenging and the reduced electron mobility introduced by nanoparticles has no effect in the conduction currents and in the negative streamer inception in the tested ZnO–C18 nanofluids is shown.

The electrical conductivity of reduced graphene oxide (rGO) obtained from graphene oxide (GO) using sodium borohydride (NaBH4) as a reducing agent has been investigated as a function of time (2 min to 24 h) and temperature (20 °C to 80 °C). Using a 300 mM aqueous NaBH4 solution at 80 °C, reduction of GO occurred to a large extent during the first 10 min, which yielded a conductivity increase of 5 orders of magnitude to 10 S m-1. During the residual 1400 min of reaction, the reduction rate decreased significantly, eventually resulting in a rGO conductivity of 1500 S m-1. High resolution XPS measurements showed that C/O increased from 2.2 for the GO to 6.9 for the rGO at the longest reaction times, due to the elimination of oxygen. The steep increase in conductivity recorded during the first 8-12 min of reaction was mainly due to the reduction of C-O (e.g., hydroxyl and epoxy) groups, suggesting the preferential attack of the reducing agent on C-O rather than C[double bond, length as m-dash]O groups. In addition, the specular variation of the percentage content of C-O bond functionalities with the sum of Csp2 and Csp3 indicated that the reduction of epoxy or hydroxyl groups had a greater impact on the restoration of the conductive nature of the graphite structure in rGO. These findings were reflected in the dramatic change in the structural stability of the rGO nanofoams produced by freeze-drying. The reduction protocol in this study allowed to achieve the highest conductivity values reported so far for the aqueous reduction of graphene oxide mediated by sodium borohydride. The 4-probe sheet resistivity approach used to measure the electrical conductivity is also, for the first time, presented in detail for filtrate sheet assemblies' of stacked GO/rGO sheets.

In this work, zinc oxide (ZnO) micron and nano sized-particles with different morphologies were synthesized by aqueous precipitation and evaluated as antimicrobial agents against foodborne pathogens. The most effective bactericide system was selected to prepare active poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) films by three different methods (i) direct melt-mixing, (ii) melt-mixing of preincorporated ZnO into PHBV18 (18 mol% valerate content) fiber mats made by electrospinning, and, (iii) as a coating of the annealed electrospun PHBV18/ZnO fiber mats over compression molded PHBV. Results showed that ZnO successfully improved the thermal stability of the PHBV18, being the preincorporation method the most efficient in mitigating the negative impact that the PHBV18 had on the thermal stability, barrier and optical properties of the PHBV films. Similar behavior was found for the coating structure although this film showed effective and prolonged antibacterial activity against Listeria monocytogenes. This study highlights the suitability of the PHBV/ZnO nanostructures for active food packaging and food contact surface applications., This work was financially supported by the Spanish Ministry of Economy and Competitiveness (MAT2012-38947-C02-01 and AGL2015-63855-C2-1-R). J.L. Castro-Mayorga is supported by the Administrative Department of Science, Technology and Innovation (Colciencias) of Colombian Government. M. J. Fabra is recipient of a Ramon y Cajal contract from the Spanish Ministry of Economy and Competitiveness.

Polyethylene nanocomposites based on functionalized ZnO nano/hierarchical particles with highly effective interfacial surface area are presented, for the next generation of ultralow transmission-loss high-voltage DC insulating materials.

Polyethylene composites based on metal oxide nanoparticles are emerging materials for use in the insulation of extruded HVDC cables. The short-term electrical performance of these materials is adeq ...

To meet the future need for clean and sustainable energies, there has been considerable interest in the development of triboelectric nanogenerators (TENGs) that scavenge waste mechanical energies. The performance of a TENG at the macroscale is determined by the multifaceted role of surface and interface properties at the nanoscale, whose understanding is critical for the future development of TENGs. Therefore, various protocols from the atomic to the macrolevel for fabrication and tuning of surfaces and interfaces are required to obtain the desired TENG performance. These protocols branch out into three categories: chemical engineering, physical engineering, and structural engineering. Chemical engineering is an affordable and optimal strategy for introducing more surface polarities and higher work functions for the improvement of charge transfer. Physical engineering includes the utilization of surface morphology control, and interlayer interactions, which can enhance the active interfacial area and electron transfer capacity. Structural engineering at the macroscale, which includes device and electrode design/modifications has a considerable effect on the performance of TENGs. Future challenges and promising research directions related to the construction of next-generation TENG devices, taking into consideration “interfaces” are also presented.

Self-motile mesoporous ZnO/Pt-based Janus micromotors accelerated by bubble propulsion that provide efficient removal of explosives and dye pollutants via photodegradation under visible light are presented. Decomposition of H

Recent progress in autonomous self-propelled multifunctional Janus nano/micromotors, which are able to convert chemical or light energy into mechanical motion, is presented. This technology of moving micro- and nanodevices is at the forefront of materials research and is a promising and growing technology with the possibility of using these motors in both biomedical and environmental applications. The development of novel multifunctional Janus motors together with their motion mechanisms is discussed. Different preparation and synthesis routes are compared. The effects of the size, interfacial structures and porosity on the directional motion and the speed of Janus micromotors are discussed. For light-derived Janus micromotors, newly developed techniques that are able to observe directly the interfaces' charge distribution on a nanometer scale are presented in order to clarify the underlying electrophoresis motion mechanism. This review aims to encourage further research in the field of micromotors using new and facile methodologies for obtaining novel Janus motors with enhanced motion and activity.

A protocol for the aqueous synthesis of ca. 1-μm-long zinc oxide (ZnO) nanorods and their growth at intermediate reaction progression is presented, together with photoluminescence (PL) characteristics after heat treatment at temperatures of up to 1000 °C. The existence of solitary rods after the complete reaction (60 min) was traced back to the development of sea urchin structures during the first 5 s of the precipitation. The rods primarily formed in later stages during the reaction due to fracture, which was supported by the frequently observed broken rod ends with sharp edges in the final material, in addition to tapered uniform rod ends consistent with their natural growth direction. The more dominant rod growth in the c direction (extending the length of the rods), together with the appearance of faceted surfaces on the sides of the rods, occurred at longer reaction times (5 min) and generated zinc-terminated particles that were more resistant to alkaline dissolution. A heat treatment for 1 h at 600 or 800 °C resulted in a smoothing of the rod surfaces, and PL measurements displayed a decreased defect emission at ca. 600 nm, which was related to the disappearance of lattice imperfections formed during the synthesis. A heat treatment at 1000 °C resulted in significant crystal growth reflected as an increase in luminescence at shorter wavelengths (ca. 510 nm). Electron microscopy revealed that the faceted rod structure was lost for ZnO rods exposed to temperatures above 600 °C, whereas even higher temperatures resulted in particle sintering and/or mass redistribution along the initially long and slender ZnO rods. The synthesized ZnO rods were a more stable Wurtzite crystal structure than previously reported ball-shaped ZnO consisting of merging sheets, which was supported by the shifts in PL spectra occurring at ca. 200 °C higher annealing temperature, in combination with a smaller thermogravimetric mass loss occurring upon heating the rods to 800 °C.

Low density polyethylene (LDPE) nanocomposites with a reduced conductivity of two orders of magnitude are reported as a novel insulation material for high voltage distribution of renewable energy. The key to the high insulation capacity was to provide 70 nm hexagonal MgO nanoparticles with relatively long, preferably 18 units long, hydrocarbon functional silsesquioxane coatings. This rendered the surface of the particles completely hydrophobic and also served as a protective layer against adsorption of polar low molecular weight atmospheric substances (H2O and CO2). The elimination of trace amounts of water, in combination with the provided carbon functionality, dramatically improved the dispersion of MgO nanoparticles. The lowest volume conductivity was ca. 7 × 10−16 S m−1 for 3 wt% surface coated nanoparticles. Extensive electron microscopy characterization was further used to relate the measured volume conductivity, acquired under conditions that resemble 800 kV high voltage direct current (HVDC) cables, to the distribution of the nanoparticles in the polymer matrix. The results show that an appropriate surface-modification approach yielded uniformly dispersed MgO nanoparticles up to contents as high as 9 wt%, with maintained 10–100 times reduced volume conductivity. Simulations of the MgO nanoparticles distribution revealed that the required interaction radius of the MgO-phase was 775 nm, setting a lower limit of particle amount to effectively work as electrical insulation promoters. The reduced volume conductivity values and scalable processing chemistry reported allow for the production of the next generation insulation material for HVDC cables.

The deterioration of acrylonitrile butadiene rubber (NBR), a common sealing material in automobile fuel systems, when exposed to rapeseed biodiesel and hydrotreated vegetable oil (HVO) was studied. ...

The effect of silsesquioxane coating of aluminium oxide nanoparticles on their dispersion and on the interfacial strength between nanoparticles and polymer matrix in low-density polyethylene compos ...

Tough fibrous membranes for smoke filtration have been developed from recycled polyethylene terephthalate (PET) bottles by solution electrospinning. The fibre thicknesses were controlled from 0.4 to 4.3 μm by adjustment of the spinning conditions. The highest fibre strength and toughness were obtained for fibres with an average diameter of 1.0 μm, 62.5 MPa and 65.8 MJ m−3, respectively. The X-ray diffraction (XRD) patterns of the fibres showed a skewed amorphous halo, whereas the differential scanning calorimetry (DSC) results revealed an apparent crystallinity of 6–8% for the 0.4 and 1 μm fibres and 0.2% crystallinity for the 4.3 μm fibres. Heat shrinkage experiments were conducted by exposing the fibres to a temperature above their glass transition temperature (Tg). The test revealed a remarkable capability of the thinnest fibres to shrink by 50%, which was in contrast to the 4.3 μm fibres, which displayed only 4% shrinkage. These thinner fibres also showed a significantly higher glass transition temperature (+15 °C) than that of the 4.3 μm fibres. The results suggested an internal morphology with a high degree of molecular orientation in the amorphous segments along the thinner fibres, consistent with a constrained mesomorphic phase formed during their rapid solidification in the electric field. Air filtration was demonstrated with cigarette smoke as a model substance passed through the fibre mats. The 0.4 μm fibres showed the most effective smoke filtration and a capacity to absorb 43× its own weight in smoke residuals, whereas the 1 μm fibres showed the best combination of filtration capacity (32×) and mechanical robustness. The use of recycled PET in the form of nanofibres is a novel way of turning waste into higher-value products.

A low temperature (60 °C) aqueous synthesis method of high purity ZnO nanoparticles intended as fillers for ultra-low electrical conductivity insulations is described. Particles were prepared under identical conditions from different zinc salts based on nitrate, chloride, sulphate or acetate to compare their abilities to form high yields of sub-50 nm particles with narrow size distribution. The acetate salt gave uniform 25 nm ZnO particles with a conical prism shape. The chloride and sulphate derived particles showed mixed morphologies of nanoprisms and submicron petals, whereas the nitrate salt yielded prisms assembled into well-defined flower shapes with spiky edges. The micron-sized flower shapes were confirmed by X-ray diffraction to consist of the smaller prism units. Photoluminescence spectroscopy showed emission in the blue-violet region with little variation depending on precursor salt, suggesting that the spectra were dependent on the primary nanoprism formation and rather independent of the final particle morphology. Microscopy revealed that the salt residuals after the reaction showed different affinity to the particle surfaces depending on the type of salt used, with the acetate creating ca. 20 nm thick hydrated shells; and in falling order of affinity: chloride, sulphate and nitrate. An acetate ion shielding effect during the synthesis was therefore assumed, preventing nanoparticle fusion during growth. Varying the concentrations of the counter-ions confirmed the shielding and only the acetate anions showed an ability to stabilize solitary nanoprisms formation in reaction yields from 2 to 10 g L−1. Ultrasonic particle surface cleaning was significantly more efficient than water replacement, resulting in a stable aqueous dispersion with a high zeta potential of 38.9 mV at pH 8.

The degradation of acrylonitrile butadiene rubber (NBR) after exposure to biodiesel at different oxygen partial pressures in an automated ageing equipment at 80 °C, and in a high-pressure autoclave at 150 °C was studied. The oxidation of biodiesel was promoted by an increase in oxygen concentration, resulting in a larger uptake of fuel in the rubber due to internal cavitation, a greater decrease in the strain-at-break of NBR due to the coalescence of cavity, and a faster increase in the crosslinking density and carbonyl index due to the promotion of the oxidation of NBR. During the high-temperature autoclave ageing, less fuel was absorbed in the rubber, because the formation of hydroperoxides and acids was impeded. The extensibility of NBR aged in the autoclave decreased only slightly due to the cleavage of rubber chains by the biodiesel attack. The degradation of NBR in the absence of carbon black was explained as being due to oxidative crosslinking. The dissolution of ZnO crystals in the acidic components of biodiesel was retarded by removing the inter-particle porosity and surface defects through heat treating star-shaped ZnO particles. The rubber containing heat-treated ZnO particles swelled less in biodiesel than a NBR filled with commercial ZnO nanoparticles, and showed a smaller decrease in the strain-at-break and less oxidative crosslinking. QC 20170228

Cross-linked polyethylene (XLPE) is the most commonly used insulating material for extruded high voltage cable applications. Degassing is a heat-treatment process that is performed to remove methan ...

Controlled aqueous growth of 1 μm flower-shaped ZnO particles with a hierarchical subset of exposed nanosheets represented by {210} crystal faces, followed by annealing at temperatures up to 1000 °C, is presented. The flower-shaped particles showed superior photocatalytic performance compared to the crystal faces of 20 nm ZnO nanoparticles. The photocatalytic reaction rate of the flower-shaped particles before annealing was 2.4 times higher per m2 compared with that of the nanoparticles with double specific surface area. Crystal surface defects and nanosized pores within the flower-shaped particles were revealed by porosity measurements and electron microscopy. A heat treatment at 400 °C was found to be optimal for removal of nanoporosity/surface defects and impurities while retaining the hierarchical superstructure. The heat treatment resulted in a photodegradation efficiency that increased by an additional 43%, although the specific surface area decreased from 16.7 to 13.0 m2g–1. The enhanced photocata...

The use of MgO nanoparticles in polyethylene for cable insulation has attracted considerable interest, although in humid media the surface regions of the nanoparticles undergo a conversion to a hydroxide phase. A facile method to obtain MgO nanoparticles with a large surface area and remarkable inertness to humidity is presented. The method involves (a) low temperature (400 °C) thermal decomposition of Mg(OH)2, (b) a silicone oxide coating to conceal the nanoparticles and prevent interparticle sintering upon exposure to high temperatures, and (c) heat treatment at 1000 °C. The formation of the hydroxide phase on these silicone oxide-coated MgO nanoparticles after extended exposure to humid air was assessed by thermogravimetry, infrared spectroscopy, and X-ray diffraction. The nanoparticles showed essentially no sign of any hydroxide phase compared to particles prepared by the conventional single-step thermal decomposition of Mg(OH)2. The moisture-resistant MgO nanoparticles showed improved dispersion and interfacial adhesion in the LDPE matrix with smaller nanosized particle clusters compared with conventionally prepared MgO. The addition of 1 wt % moisture-resistant MgO nanoparticles was sufficient to decrease the conductivity of polyethylene 30 times. The reduction in conductivity is discussed in terms of defect concentration on the surface of the moisture-resistant MgO nanoparticles at the polymer/nanoparticle interface.

Toughening amplification of the neat poly(vinyl chloride) (PVC) and its reinforced version containing 25 phr of the cellulose acetate (CA)-compatibilized starch using methyl methacrylate-butadiene-styrene (MBS) core―shell particles was studied. The room temperature measured impact strength of the PVC showed mild increase up to 10 wt % with the addition of MBS particles. Then, the toughness enhanced discontinuously to super-tough plateau regime. The room temperature measured impact strength of PVC containing 20 phr of MBS particles, however, was reduced by as much as 95% when it was filled with 25 phr of the CA-compatibilized starch. In addition, the brittle―ductile transition (BDT) of the toughened PVC increased from 0 to 60 °C because of its reinforcement, even though the matrix number density of the core/shell particles remained almost constant. The decline in the impact strength and the rise in the BDT of the hybrid PVC system were attributed to the decrease in the shear deformable matrix and shear deformation propagation rate despite the increase in the process zone size. Maximum impact strength of the hybrid system at 60 °C (its BDT) increased to about 25% of the toughened PVC at its BDT (0 °C). The toughness amplification correlation of the toughened and hybrid PVC systems with their process zones fractional stress volumes under the impact load showed three regimes: quasi-tough, transition, and super-tough, which were superimposable on literature data regarding hybrid nylon 66 systems.