Search

This paper presents a unique study on the dynamic identification of the tallest glue-laminated timber frame building in the world using forced vibration tests (FVTs) and long-term ambient vibration tests (AVTs). Because the amount of sway in service under wind has become the governing design criterion for tall timber buildings, this paper aims to provide useful information and evaluate available tools and methods for modal identification in tall glulam timber frame buildings. First, combined operational modal analysis schemes based on the variational mode decomposition with the stochastic subspace identification and the random decrement technique were adopted to identify the modal properties from nonstationary ambient data. Then, unique full-scale forced vibration tests were conducted using two different methods to excite the building: measured electrodynamic shakers excitation and unmeasured rhythmic human-induced excitation. Finally, a finite-element (FE) model of the tall glulam frame building was developed and frequency response function (FRF)–based model updating was conducted showing that the FE model was able to predict the modal behavior of the test building. The results show that natural frequencies identified from output-only techniques are in good agreement with the FVT results. Damping ratios obtained from both AVTs and FVTs exhibited amplitude-dependent behavior with a larger variation observed in the FVT results due to larger range of response amplitudes. These results have significant consequences for the design of tall timber buildings under serviceability-level loading, where damping plays an important role. The resulting damping ranges presented in this paper can serve as a useful guideline for practicing engineers in developing their prediction models of tall timber buildings under serviceability-level loading. [ABSTRACT FROM AUTHOR]

Various approaches have been proposed for bridge structural health monitoring. One of the earliest approaches proposed was tracking a bridge's natural frequency over time to look for abnormal shifts in frequency that might indicate a change in stiffness. However, bridge frequencies change naturally as the structure's temperature changes. Data models can be used to overcome this problem by predicting normal changes to a structure's natural frequency and comparing it to the historical normal behaviour of the bridge and, therefore, identifying abnormal behaviour. Most of the proposed data modelling work has been from long-span bridges where you generally have large datasets to work with. A more limited body of research has been conducted where there is a sparse amount of data, but even this has only been demonstrated on single bridges. Therefore, the novelty of this work is that it expands on previous work using sparse instrumentation across a network of bridges. The data collected from four in-operation bridges were used to validate data models and test the capabilities of the data models across a range of bridge types/sizes. The MID approach was found to be able to detect an average frequency shift of 0.021 Hz across all of the data models. The significance of this demonstration across different bridge types is the practical utility of these data models to be used across entire bridge networks, enabling accurate and informed decision making in bridge maintenance and management. [ABSTRACT FROM AUTHOR]

Structural Health Monitoring (SHM) is a technique that involves gathering information to ensure that a structure is safe and behaving as expected. Within SHM, vibration-based monitoring is generally seen as one of the more cost-effective types of monitoring. However, vibration-based monitoring has mostly been undertaken on long-span bridges using data collected with a dense network of sensors. Historically, the logistical difficulty of collecting data on short- and medium-span bridges has meant that the usefulness of vibration-based methods on these bridges is largely unknown. Therefore, this study proposes Minimal Information Data-modelling (MID). MID is an approach that utilises low-cost, easily implementable sensors that are potentially feasible for operators to purchase and operate across a network. This approach will be investigated to determine whether MID is a feasible approach for monitoring short- and medium- span bridges. The results from MID were assessed to determine whether they could detect a suitably small shift in frequency, which is indicative of damage. It was determined that the data models could reliably detect frequency shifts as low as 0.01 Hz. This magnitude of frequency shift is similar to the level of frequency shift reported for a range of bridge damage cases found by others and validated with FE models. The accuracy achieved by the data models indicates that MID could potentially be used as a damage detection method. The cost of the equipment used to collect the data was approximately £370, demonstrating that it is feasible to use MID to monitor bridges across an entire network. [ABSTRACT FROM AUTHOR]

Based on the experimental estimation of the key dynamic properties of a seven-storey building made entirely of cross-laminated timber (CLT) panels, the finite element (FE) model updating was performed. The dynamic properties were obtained from an input-output full-scale modal testing of the building in operation. The chosen parameters for the FE model updating allowed the consideration of the timber connections in a smeared sense. This approach led to an excellent match between the first six experimental and numerical modes of vibrations, despite spatial aliasing. Moreover, it allowed, together with the sensitivity analysis, to estimate the stiffness (affected by the connections) of the building structural elements. Thus, the study provides an insight into the as-built stiffness and modal properties of tall CLT building. This is valuable because of the currently limited knowledge about the dynamics of tall timber buildings under service loadings, especially because their design is predominantly governed by the wind-generated vibrations. [ABSTRACT FROM AUTHOR]

Summary: The current study is to find out alternative damping to provide satisfactory vibration suppression performance in civil engineering. Accordingly, electromagnetic actuators and electromagnetic dampers (EMDs) are utilised to generate electromagnetic damping. For further discussion on control of vibration serviceability problem in civil structure, the use of a linear voice coil motor (LVCM) as an EMD is implemented to attenuate unwanted vibration. To induce appropriate electromagnetic damping, the terminal ends of the LVCM need to connect with shunt circuits. The basic resistor series circuit and resistor, inductor, and capacitor (RLC) oscillating circuit are employed to connect to the LVCM in terms of enhancing the EMD damping. However, a design of the electromagnetic shunt damper (EMSD) is required with the generic H∞ and H2 robust optimisation techniques to determine shunt circuit components, in which the results of these optimisations were discussed on the previous author study. For extending the EMSD study, the resulting EMSD is experimentally exploited to a six‐storey aluminium frame structure. The random and harmonic excitations are selected to input to the structure to examine the performance of the electromagnetic damping. The finding of the experimental test of the EMSD gives satisfactory vibration suppression performance. [ABSTRACT FROM AUTHOR]