Search

Here, the effect of thermal annealing (TA) on the stability of solution‐sheared thin films of the semiconducting polymer poly[2,5‐bis(2‐octyldodecyl)pyrrolo[3,4‐c]pyrrole‐1,4(2H,5H)‐dione‐3,6‐diyl)‐alt‐(2,2′;5′,2′';5′',2′"‐quaterthiophen‐5,5′"‐diyl)] (PDPP4T) against the original coating solvent is studied, and it is shown that TA significantly improves the solvent resistance of semiconducting polymer films. Specifically, after the thin films are annealed at or above a critical temperature, the thin film thickness is largely retained when exposed to the original solvent, while for lower annealing temperatures material loss occurs, i.e., the thin film thickness is reduced due to rapid dissolution. The results of various techniques including grazing‐incidence wide‐angle x‐ray scattering (GIWAXS), atomic force microscopy (AFM), and ultraviolet‐visible‐near infrared (UV–vis‐NIR) absorption spectroscopy suggest physical changes as the cause for the increased solvent resistance. Such annealed films also show stable electrical characteristics in bottom‐gate, top‐contact (BGTC) organic field‐effect transistors (OFETs) even after solvent exposure. In initial tests, a multitude of technologically relevant polymers show such behavior, underlining the potential impact of such temperature treatments for the fabrication of multi‐layer polymer devices. [ABSTRACT FROM AUTHOR]

State-of-the-art Li batteries suffer from serious safety hazards caused by the reactivity of lithium and the flammable nature of liquid electrolytes. This work develops highly efficient solid-state electrolytes consisting of imidazolium-containing polyionic liquids (PILs) and lithium bis(trifluoromethane sulfonyl)imide (LiTFSI). By employing PIL/LiTFSI electrolyte membranes blended with poly(propylene carbonate) (PPC), we addressed the problem of combining ionic conductivity and mechanical properties in one material. It was found that PPC acts as a mechanically reinforcing component that does not reduce but even enhances the ionic conductivity. While pure PILs are liquids, the tricomponent PPC/PIL/LiTFSI blends are rubber-like materials with a Young's modulus in the range of 100 MPa. The high mechanical strength of the material enables fabrication of mechanically robust free-standing membranes. The tricomponent PPC/PIL/LiTFSI membranes have an ionic conductivity of 10−6 S·cm−1 at room temperature, exhibiting conductivity that is two orders of magnitude greater than bicomponent PPC/LiTFSI membranes. At 60 °C, the conductivity of PPC/PIL/LiTFSI membranes increases to 10−5 S·cm−1 and further increases to 10−3 S·cm−1 in the presence of plasticizers. Cyclic voltammetry measurements reveal good electrochemical stability of the tricomponent PIL/PPC/LiTFSI membrane that potentially ranges from 0 to 4.5 V vs. Li/Li+. The mechanically reinforced membranes developed in this work are promising electrolytes for potential applications in solid-state batteries. [ABSTRACT FROM AUTHOR]

Non‐isothermal crystallization of poly(ε‐caprolactone) (PCL) in semi‐crystalline/amorphous PCL/poly(styrene‐co‐acrylonitrile) (SAN) blends with lower‐critical solution temperature (LCST) phase behavior at temperatures higher than the beginning of PCL crystallization has been studied and quantitatively modeled using different kinetics models. Near‐ and off‐critical PCL/SAN blends were prepared by using two different PCL molecular weights. The kinetics model results verified that the samples containing PCL with higher molecular weight have lower crystallinity and faster crystallization behavior, while adding amorphous SAN chains to PCL retards the crystallization process. A lower crystallization activation energy was relatively required for higher molecular weight, PCL‐2, in off‐critical PCL/SAN blends. However, the easier crystallization with higher degree of crystallinity was attained in near‐critical P80S20 blend containing PCL with lower molecular weight, indicating a shift of the LCST phase diagram of the PCL/SAN blend to higher temperatures by increasing the PCL molecular weight. [ABSTRACT FROM AUTHOR]