Search

A molecularly designed imprinting method was combined with a gravimetric nanosensor for the real-time detection Cu(II) ions in aqueous solutions without using expensive laboratory devices. Thus, 1:1 and 2:1 mol-ratio-dependent coordination modes between Cu(II), N-methacyloly-L histidine methyl ester (MAH) functional monomer complexes, and their four-fold and six-fold coordinations were calculated by means of density functional theory molecular modeling. Cu(II)-MIP1 and Cu(II)-MIP2 nanoparticles were synthesized in the size range of 80-100 nm and characterized by SEM, AFM and FTIR. Cu(II)-MIP nanoparticles were then conducted to a quartz crystal microbalance sensor for the real-time detection of Cu(II) ions in aqueous solutions. The effects of initial Cu(II) concentration, selectivity, and imprinting efficiency were investigated for the optimization of the nanosensor. Linearity of 99% was obtained in the Cu(II) ion linear concentration range of 0.15-1.57 µM with high sensitivity. The LOD was obtained as 40.7 nM for Cu(II)-MIP2 nanoparticles. The selectivity and the imprinting efficiency of the QCM nanosensor were obtained significantly in the presence of competitive ion samples (Co(II), Ni(II), Zn(II), and Fe(II)). The results are promising for sensing Cu(II) ions as environmental toxicants in water by combining molecularly designed ion-imprinted nanoparticles and a gravimetric sensor.

Considering the limitations of well-known traditional detection techniques, innovative research studies have focused on the development of new sensors to offer label-free, highly sensitive, real-time, low-cost, and rapid detection for biomolecular interactions. In this study, we demonstrate immunoglobulin G (IgG) detection in aqueous solutions by using real-time and label-free kinetic measurements of the Interferometric Reflectance Imaging Sensor (IRIS) system. By performing kinetic characterization experiments, the sensor's performance is comprehensively evaluated and a high correlation coefficient value (>0.94) is obtained in the IgG concentration range of 1-50 μg/mL with a low detection limit (0.25 μg/mL or 1.67 nM). Moreover, the highly sensitive imaging system ensures accurate quantification and reliable validation of recorded binding events, offering new perspectives in terms of direct biomarker detection for clinical applications., (Copyright © 2022 Elsevier B.V. All rights reserved.)

The field of biosensing is in constant evolution, propelled by the need for sensitive, reliable platforms that provide consistent results, especially in the drug development industry, where small molecule characterization is of uttermost relevance. Kinetic characterization of small biochemicals is particularly challenging, and has required sensor developers to find solutions to compensate for the lack of sensitivity of their instruments. In this regard, surface chemistry plays a crucial role. The ligands need to be efficiently immobilized on the sensor surface, and probe distribution, maintenance of their native structure and efficient diffusion of the analyte to the surface need to be optimized. In order to enhance the signal generated by low molecular weight targets, surface plasmon resonance sensors utilize a high density of probes on the surface by employing a thick dextran matrix, resulting in a three-dimensional, multilayer distribution of molecules. Despite increasing the binding signal, this method can generate artifacts, due to the diffusion dependence of surface binding, affecting the accuracy of measured affinity constants. On the other hand, when working with planar surface chemistries, an incredibly high sensitivity is required for low molecular weight analytes, and furthermore the standard method for immobilizing single layers of molecules based on self-assembled monolayers (SAM) of epoxysilane has been demonstrated to promote protein denaturation, thus being far from ideal. Here, we will give a concise overview of the impact of tridimensional immobilization of ligands on label-free biosensors, mostly focusing on the effect of diffusion on binding affinity constants measurements. We will comment on how multilayering of probes is certainly useful in terms of increasing the sensitivity of the sensor, but can cause steric hindrance, mass transport and other diffusion effects. On the other hand, probe monolayers on epoxysilane chemistries do not undergo diffusion effect but rather other artifacts can occur due to probe distortion. Finally, a combination of tridimensional polymeric chemistry and probe monolayer is presented and reviewed, showing advantages and disadvantages over the other two approaches.

Quartz crystal microbalance (QCM) is a highly sensitive system that is used as a biosensor for biomolecules and cells. Detection and characterization of cancer cells in circulation or biopsy samples is of crucial importance for cancer diagnosis. Here, we introduce approaches for breast cancer cell detection via their surface molecules. The sensor system is based on preliminary coating of QCM chip with polymeric nanoparticles to increase the surface area and allow for the attachment of proteins to the chip surface. This is followed by the attachment of a specific protein in order to functionalize the chip. Breast cancer cells and fibroblast cells as control are cultured and applied to this chip. The functionalized QCM system can detect breast cancer cells with high affinity and selectivity. Here, we present the preparation methods of QCM-based sensors for selective detection of MDA MB 231 cancer cells. Selectivity of QCM-based sensor is carried out in the presence of L929 mouse fibroblast cells., (© 2022. Springer Science+Business Media, LLC, part of Springer Nature.)

Molecularly imprinted polymer-based surface plasmon resonance sensor prepared using silver nanoparticles was designed for the selective recognition of Penicillin G (PEN-G) antibiotic from both aqueous solution and milk sample. PEN-G imprinted sensors (NpMIPs) SPR sensor was fabricated using poly (2-hydroxyethyl methacrylate-N-methacroyl-(L)-cysteine methyl ester)-silver nanoparticles-N-methacryloyl-L-phenylalanine methyl ester polymer by embedding silver nanoparticles (AgNPs) into the polymeric film structure. In addition, a non-imprinted (NpNIPs) SPR sensor was prepared by utilizing the same polymerization recipe without addition of the PEN-G template molecule to evaluate the imprinting effect. FTIR-ATR spectrophotometer, ellipsometer, contact angle measurements were used for the characterization of NpMIPs SPR sensors. The linear concentration range of 0.01-10 ng/mL PEN-G was studied for kinetic analyses. The augmenting effect of AgNPs used to increase the surface plasmon resonance signal response was examined using polymer-based PEN-G imprinted (MIPs) sensor without the addition of AgNPs. The antibiotic amount present in milk chosen as a real sample was measured by spiking PEN-G into the milk. According to the Scatchard, Langmuir, Freundlich and Langmuir-Freundlich adsorption models, the interaction mechanism was estimated to be compatible with the Langmuir model.

SPR sensor used for amitrole detection was prepared without using any modification. Molecularly imprinted SPR sensor enabled high selectivity for amitrole pesticide. Amino acid-based functional monomer MATrp was integrated as a recognition element. Tailor-made SPR sensor enables real-time monitoring of amitrole pesticide. Synthetic recognition sites provided by MATrp were prepared without labeling., (© 2021 John Wiley & Sons Ltd.)

Microfluidic devices have led to novel biological advances through the improvement of micro systems that can mimic and measure. Microsystems easily handle sub-microliter volumes, obviously with guidance presumably through laminated fluid flows. Microfluidic systems have production methods that do not need expert engineering, away from a centralized laboratory, and can implement basic and point of care analysis, and this has attracted attention to their widespread dissemination and adaptation to specific biological issues. The general use of microfluidic tools in clinical settings can be seen in pregnancy tests and diabetic control, but recently microfluidic platforms have become a key novel technology for cancer diagnostics. Cancer is a heterogeneous group of diseases that needs a multimodal paradigm to diagnose, manage, and treat. Using advanced technologies can enable this, providing better diagnosis and treatment for cancer patients. Microfluidic tools have evolved as a promising tool in the field of cancer such as detection of a single cancer cell, liquid biopsy, drug screening modeling angiogenesis, and metastasis detection. This review summarizes the need for the low-abundant blood and serum cancer diagnosis with microfluidic tools and the progress that has been followed to develop integrated microfluidic platforms for this application in the last few years.

In this work, a surface plasmon resonance (SPR) based immunosensor was prepared by the immobilization of the amine-functionalized gold nanoparticles (N-AuNPs) on the sensing surface to sense immunoglobulin M (IgM) antibodies in the aqueous solution and artificial plasma. The characterization studies of SPR based immunosensor for IgM detection were performed with scanning electron microscope (SEM), contact angle measurements, and ellipsometry. Kinetic studies for the IgM immunosensor were carried out in the range of 1.0 to 200 ng/mL IgM concentrations in an aqueous solution. The total IgM analysis time including adsorption, desorption, and regeneration cycles was nearly 10 min for the prepared immunosensor. The limit of detection (LOD) and limit of quantification (LOQ) were found as 0.08 and 0.26 ng/mL, respectively. The reusability of the proposed immunosensor was tested with 6 consecutive adsorption-desorption, and regeneration cycles. Also, enzyme-linked immunosorbent assay (ELISA) method was utilized in the validation of the immunosensor.

The development of novel biocompatible and cost effective cryogel membrane which shows enhanced antimicrobial properties in order to use for several approaches such as wound dressing, scaffold or food packaging was aimed in this study. A super macro porous lysozyme imprinted cryogel membranes showing antibacterial effect against both Gram-positive and Gram-negative bacteria were prepared by using molecular imprinting technique. N-methacryloyl-(L)-histidine methyl ester (MAH) was used as the pseudo specific ligand and complexed with Cu ++ in order to provide metal ion coordination between MAH and template molecule (lysozyme). Comparing the antibacterial activity of different lysozyme concentrations, cryogel membranes were prepared in three different concentrations. To synthesize Poly (hydroxyethyl methacrylate-N-methacryloyl-(L)-histidine methylester) P(HEMA-MAH) cryogel membrane, free radical polymerization initiated by N, N, N', N'-tetramethylene diamine (TEMED) and ammonium persulfate (APS) was carried out at -12 °C. The characterization of the lysozyme imprinted cryogel membrane was accomplished by using scanning electron microscopy (SEM), swelling degree measurements and Fourier transform infrared spectroscopy-attenuated total reflectance (FTIR-ATR) spectroscopy. The cytotoxicity test of produced membrane was performed by using mouse fibroblast cell line L929. The antibacterial activity of P(HEMA-MAH) lysozyme molecular imprinted [P(HEMA-MAH) Lyz-MIP] cryogel membranes against Staphylococcus aureus ( S. aureus ) and Escherichia coli ( E. coli ) were determined by Kirby-Bauer membranes diffusion and viable cell counting methods. When the antibacterial effect of P(HEMA-MAH) Lyz-MIP cryogel membranes were evaluated, it was found that P(HEMA-MAH) Lyz-MIP cryogel membranes had stronger antibacterial effects against Gram-negative E. coli bacteria even in low lysozyme concentrations. In addition, 100% bacterial inhibition was detected for both of two bacteria at increasing lysozyme concentrations.

Over the past few decades, a significant increase in multi-drug-resistant pathogenic microorganisms has been of great concern and directed the research subject to the challenges that the distribution of resistance genes represent. Globally, high levels of multi-drug resistance represent a significant health threat and there is a growing requirement of rapid, accurate, real-time detection which plays a key role in tracking of measures for the infections caused by these bacterial strains. It is also important to reduce transfer of resistance genes to new organisms. The, World Health Organization has informed that millions of deaths have been reported each year recently. To detect the resistant organisms traditional detection approaches face limitations, therefore, newly developed technologies are needed that are suitable to be used in large-scale applications. In the present study, the aim was to design a surface plasmon resonance (SPR) sensor with micro-contact imprinted sensor chips for the detection of Staphylococcus aureus . Whole cell imprinting was performed by N -methacryloyl-L-histidine methyl ester (MAH) under UV polymerization. Sensing experiments were done within a concentration range of 1.0 × 10 2 -2.0 × 10 5 CFU/mL. The recognition of S. aureus was accomplished by the involvement of microcontact imprinting and optical sensor technology with a detection limit of 1.5 × 10 3 CFU/mL. Selectivity of the generated sensor was evaluated through injections of competing bacterial strains. The responses for the different strains were compared to that of S. aureus. Besides, real experiments were performed with milk samples spiked with S. aureus and it was demonstrated that the prepared sensor platform was applicable for real samples.

Molecularly imprinted polymers are used for creating a specific cavity and selective recognition sites for the structure of a target molecule in a polymeric structure. In this study, specific molecularly imprinted cryogel cartridges were synthesized using two distinct functional monomers to compare imprinting efficiency for the selective recognition of Tyrosine (Tyr). Tyr-imprinted cryogel cartridge (MIP1) was prepared using metal-chelate coordination for the imprinting process by free-radical bulk polymerization under frozen conditions, and Tyr-imprinted cryogel cartridge (MIP2) was prepared in the same way using hydrophobic effects for imprinting. After the characterization of the cryogel cartridges was carried out, the optimum adsorption conditions of both were determined according to the different parameters such as flow rate (0.5-2.5 ml/min), pH of the medium (4.0-8.0), initial Tyr concentration (0.1-3.0 mg/ml), and temperature (4-45°C). Selectivity experiments of Tyr-imprinted and non-imprinted cryogel cartridges were carried out by using phenylalanine, tryptophan, and cysteine. Besides, the eluted Tyr from MIP1 and MIP2 cryogel cartridge were applied to FPLC system. Also, the reusability experiments of Tyr-imprinted cryogel cartridges was observed no significant decrease in the adsorption capacity., (© 2020 American Institute of Chemical Engineers.)

In this study, composite polymeric cryogel cartridges were achieved by using Cd(II) imprinted poly(hydroxyethyl methacrylate N-methacryloly-(L)-cysteine methylester) beads and poly(hydroxyethyl methacrylate) cryogel cartridges with two different mole ratios of functional monomer. The N-methacryloly-(L)-cysteinemethylester was used as a functional monomer and Cd(II) 1:1 and 2:1, which were then notated as MIP1 and MIP2, respectively. Various characterization methods have confirmed the structural transformation on the MIP1 and MIP2 composite cryogel cartridges by scanning electron microscopy, Fourier-transform infrared spectroscopy-Attenuated Total Reflectance, and swelling tests. The maximum amount of Cd(II) adsorption with composite cryogel cartridges was determined by altering the Cd(II) initial concentration, temperature, and pH values. The maximum adsorption capacity of MIP1 and MIP2 composite cryogel cartridges obtained was 76.35 and 98.8 µmol/g of composite cryogels, respectively. The adsorption studies revealed that the MIP2 possessed a good adsorption performance for Cd(II). The obtained composite cryogel cartridges have a selective, reusable, and cost-friendly potential for the removal of Cd(II) from aqueous solutions, and are used many times without decreasing their adsorption capacities significantly. The Cd(II) removal rate of the MIP1 and MIP2 composite cryogel cartridges from synthetic wastewater samples was determined as 98.8%. The obtained cryogel cartridges' adsorption material exhibited a good directional removal performance for Cd(II) from wastewater samples.

Human immunoglobulin M (hIgM) antibodies are considered as hopeful tools for diseases therapy. Therefore, chromatography approaches are used to purify hIgM with a single step. In this study, we prepared a poly(hydroxyethyl methacrylate) based immunoaffinity p(HEMA-I) cryogel column by using cyanamide to immobilize antihuman immunoglobulin on the p(HEMA) cryogel for purification of hIgM in aqueous solution and artificial human plasma. The characterization of the p(HEMA) cryogel column was performed by using a scanning electron microscope (SEM), micro-computerized tomography (µ-CT), Fourier transform infrared spectroscopy (FTIR), swelling degree and macro-porosity. Further, the optimizations of various parameters were performed such as, pH, ionic strength, temperature and concentration of hIgM in aqueous solutions. In addition, the Langmuir adsorption model was supported by experimental results. Maximum adsorbed amount of hIgM corresponded to 11.1 mg/g at pH 5.75 [morpholino ethanesulfonic acid (MES buffer)]. Our results indicated that the p(HEMA-I) cryogel column can be reused at least 10 times without significant loss in adsorption capacity. As a natural source, artificial human plasma was selected for hIgM adsorption and the purity of hIgM was evaluated using sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE)., Competing Interests: There is no conflict of interest for authors.

Background and Objectives: Benign Prostatic Hyperplasia (BPH) is a common urological disorder as men get older. BPH can cause uncomfortable urinary tract symptoms. Given the high incidence of the disease, further research is an undeniable necessity for its better management. In this research, the efficacy of Urtica Dioica root extract (UDE) on clinical and biochemical parameters were evaluated in this type of patients., Materials and Methods: Participants were 60 men with BPH that randomly allocated to two equal groups (Intervention = 30 and Comparison = 30). Block balanced Randomization method was performed using a computer by a trained nurse. Intervention and comparison groups received 450 mg day-1 UDE and placebo as tablets for 12 weeks, respectively. The main outcome was changes in International Prostate Symptoms Score (IPSS) from baseline to end of treatment. Data were collected by completing a standard questionnaire and performing relevant tests based on common laboratory methods., Results: UDE had an intermediate effect on IPSS, a small effect on serum high-sensitivity C-reactive protein (hs-CRP), intermediate to large effect on malondialdehyde (MDA) levels and intermediate effect on superoxide dismutase (SOD) activity. The magnitude of the effects of UDE on other parameters was overall negligible compared to the comparison and not significant. No side effects were seen in these patients following tablet usage., Conclusion: UDE consumption for 12 weeks among BPH patients had clinically significant effects on IPSS, serum hs-CRP, MDA and SOD activity.

Concanavalin A is a representative of the plant protein group known as lectins. Many lectin proteins have useful characteristics for studies on cell division and cell surfaces. In this study, a new adsorbent for the specific separation of Concanavalin A was prepared by applying a silica particle surface imprinting method. First, silica particles were activated via acidic treatment, and then, 3-methacryloyloxypropyl trimethoxysilane (MPTMS) was used for modification. For the preparation of Concanavalin A surface-imprinted silica particles (Con A-MISPs), N-methacryloyl-l-histidine methyl ester (MAH) was used as a functional monomer. The silica particles were characterized using a Zetasizer, scanning electron microscopy equipment (SEM), and Fourier transform infrared spectroscopy (FTIR). The effects of parameters such as the pH, initial concentration of Concanavalin A, and temperature on the adsorption of Concanavalin A were determined. The maximum Concanavalin A adsorption onto Con A-MISPs was observed to be 305.2 mg/g at a pH of 6. The reusability of the Con A-MISPs was approximately 93.5%. The non-imprinted silica particles (NISPs) were prepared in the same manner without Concanavalin A to compare the surface imprinting factor. Selective binding studies were carried out with lysozyme and hemoglobin molecules. The selectivity of the Con A-MISPs was also investigated by isolating Concanavalin A from Canavalia ensiformis. The purity of the Concanavalin A was shown by sodium dodecyl sulphate polyacrylamide gel electrophoresis (SDS-PAGE)., (Copyright © 2019 Elsevier B.V. All rights reserved.)

The aim of the present study was developing a surface plasmon resonance (SPR) nanosensor to detect Escherichia coli (E. coli) for the diagnosis of urinary tract infections by using surface imprinted Au nanoparticles (AuNPs) as a recognition element. In order to realize imprinting, Cu(II) ions were used to provide interaction between E. coli cell wall and amine functionalized AuNPs forming cavities on the surface of nanosensor. E. coli surface imprinted AuNPs nanosensor was characterized by using ellipsometry, contact angle measurement, scanning electron microscopy (SEM) and atomic force microscopy (AFM). The real time detection of E. coli was evaluated by using E. coli suspensions in the concentration range of 1 × 10 3 -0.5 × 10 1  CFU/mL. Combination of the signal enhancing properties of AuNPs and surface imprinting technique provided ultrasensitive detection with a comparatively low limit of detection value (1 CFU/mL) to the SPR nanosensor system. Selectivity experiments were performed by using Staphylococcus aureus, Klebsiella pneumoniae and Pseudomonas aeruginosa. The highest response was recorded for E. coli, as expected. Additionally, the recognition of E. coli even in a complex medium such as artificial urine sample was achieved by the developed nanosensing system. Also, this chip can be used repeatedly without seen signal reducing for four-time consecutive. In the view of these results, it was emphasized that this novel sensing system has a potency for the selective, very sensitive, rapid and real time detection of causative agent in order to diagnose E. coli caused infections., (Copyright © 2019. Published by Elsevier B.V.)

Breast cancer is the most common cancer in women with increasing insidance. Breast cancer occurs as a result of some molecular changes, such as aberrant or dysregulated expression of receptors, in breast epithelial cells. Therefore, breast cancer cells can be detected through their membrane receptors using specific antibodies. This study aims to form a quartz crystal microbalance (QCM) biosensor to detect breast cancer cells. Notch receptor signaling directs many pathways in developing breast tissue and its expression is found to be aberrant or disregulated in metastatic breast cancer cells. Its involvement in malignant transformation makes it a potential drug target. The human metastatic breast cancer cells, MDA MB 231 cells, are used here as a model due to the overexpression of notch-4 receptor on their membranes. First, to increase the surface area of the chip poly(2-hydroxyethyl methacrylate-PHEMA) nanoparticles were synthesized and were placed on QCM chip surface. Then, the surface was further modified and functionalized by binding notch-4 receptor antibody using carbodiimide. Nanoparticle coated and antibody attached QCM chips were characterized via FTIR-ATR, ellipsometry, contact angle measurements and by atomic force microscopy. MDA MB 231 cell samples ranging in numbers between 50-300 cells/ml were introduced to the functionalized QCM chip at a flow rate of 1.0 mL/min and the resonance frequency (f 0 ) was recorded. Then, cell samples were applied to the QCM biosensor and the resonance frequency was monitored. The binding mode fitted best to Langmuir isotherm model. Sensitivity is found to be high and the selectivity as tested by competitive adsorption of L929 mouse fibroblast cells showed that QCM biosensor was 17.5 times more selective for MDA MB 231 cells than the fibroblast cells. The chip was reusable and was stable over 3 months. These results indicate that, the notch-4 receptor antibody PHEMA nanoparticle QCM biosensor is highly selective and efficient system that may be used for cancer cell detection., (Copyright © 2019. Published by Elsevier B.V.)

This study aims to develop molecularly imprinted based quartz crystal microbalance (QCM) and surface plasmon resonance (SPR) sensors for highly sensitive and selective detection of 2,4-dichlorophenoxyacetic acid (2,4-D) and to determine their accuracy and precision by liquid chromatography-tandem mass spectrometry (LC-MS/MS) as a reference technique. Here, we synthesized non-imprinted (NIP) and 2,4-D-imprinted (MIP) [ethylene glycol dimetacrylate-N-metacryloyl-(l)-tryptophan methyl ester-p(EGDMA-MATrp)] polymeric nanofilms by using molecular imprinting technique. MIP and NIP nanofilms were characterized by fourier transform infrared spectroscopy attenuated total reflectance (FTIR-ATR), atomic force microscope (AFM), contact angle and ellipsometer measurements. The molecular imprinting procedures were successfully carried out and it was found that the prepared polymeric surfaces were highly desirable for sensitive recognition by QCM and SPR sensors. Competitive experiments for the sensors revealed that MIP nanofilms were found to show more sensitivity and selectivity than NIP ones. The sensor responses have a good linear relationship with 2,4-D concentrations in the range of 0.23-8.0 nM with a limit of detection at 20.17 ng/L for QCM and 24.57 ng/L for SPR sensors. In conclusion, both QCM and SPR sensor systems showed good accuracy and precision, with recovery percentages between 90 and 92% and 87-93%, respectively. Furthermore, they have a fast response time, reusability, high selectivity and sensitivity and low limit of detection., (Copyright © 2019 Elsevier B.V. All rights reserved.)

The aim of this work is to develop drug carrier system with high loading capacity and controlled drug release profile for antibiotic release. For this purpose, composite molecularly imprinted nanofibers were prepared via in-situ graft polymerization of methacrylic acid as a monomer, N,N'-methylene bisacrylamide as a crosslinker and gentamicin sulfate as a template molecule onto surface-modified bacterial cellulose nanofibers. Gentamicin imprinted microparticles were fabricated onto bacterial cellulose nanofibers resulting in the formation of composite BC nanofibers. Thus, the composite nanofibers incorporated with gentamicin imprinted microparticles were achieved to fabricated. The in-vitro drug release tests were performed to evaluate the release performance of the resultant composite nanofibers at 37 °C. Also, kinetic models were applied to the drug release data. It was determined that the drug release from the composite molecularly imprinted nanofibers fit well in the Korsmeyer-Peppas model.

Molecular imprinting technique was used for the preparation of antibiotic and anti-neoplastic chemotherapy drug (mitomycin C) imprinted cryogel membranes (MMC-ICM). The membranes were synthezied by using metal ion coordination interactions with N-methacryloyl-(l)-histidine methyl ester (MAH) functional monomer and template molecules (i.e. MMC). The 2-hydroxyethyl methacrylate (HEMA) monomer and methylene bisacrylamide (MBAAm) crosslinker were used for the preparation of mitomycin C imprinted cryogel membranes by radical suspension polymerization technique. The imprinted cryogel membranes were characterized by scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET), Fourier transform infrared spectroscopy-attenuated total reflectance (FTIR-ATR) and swelling degree measurements. Cytotoxicity of MMC-ICMs was investigated using mouse fibroblast cell line L929. Time-dependent release of MMC was demonstrated within 150 h from cryogel membranes. Cryogels demonstrated very high MMC loading efficiency (70-80%) and sustained MMC release over hours.

There is a significant need for the development of the novel adsorbents in the field of protein purification. In this study, thin hemoglobin imprinted film (MIP) was fabricated onto the bacterial cellulose nanofibers' (BCNFs) by surface imprinting method using metal ion coordination interactions with N-methacryloyl-(L)-histidinemethylester (MAH) and copper ions. The hemoglobin surface imprinted bacterial cellulose nanofibers (MIP-BCNFs) was applied to selective recognition of hemoglobin and purification from hemolysate. The characterization of the MIP-BCNFs was carried out by the Fourier Transformed Infrared Spectroscopy (FT-IR), Scanning Electron Microscopy (SEM), micro-Computerized Tomography (μCT), atomic force microscopy (AFM) and surface area measurements. The adsorption experiments of hemoglobin onto the MIP-BCNFs and NIP-BCNFs from aqueous hemoglobin solutions were investigated in a batch system. The results showed that MIP-BCNFs are promising materials for purification of hemoglobin with high adsorption capacity, significant selectivity and reusability., (Copyright © 2017 Elsevier B.V. All rights reserved.)

Identification of pathogenic microorganisms by traditional methods is slow and cumbersome. Therefore, the focus today is on developing new and quicker analytical methods. In this study, a Surface Plasmon Resonance (SPR) sensor with a microcontact imprinted sensor chip was developed for detecting Salmonella paratyphi . For this purpose, the stamps of the target microorganism were prepared and then, microcontact S. paratyphi -imprinted SPR chips were prepared with the functional monomer N-methacryloyl-L-histidine methyl ester (MAH). Characterization studies of the SPR chips were carried out with ellipsometry and scanning electron microscopy (SEM). The real-time Salmonella paratyphi detection was performed within the range of 2.5 × 10⁶-15 × 10⁶ CFU/mL. Selectivity of the prepared sensors was examined by using competing bacterial strains such as Escherichia coli , Staphylococcus aureus and Bacillus subtilis . The imprinting efficiency of the prepared sensor system was determined by evaluating the responses of the SPR chips prepared with both molecularly imprinted polymers (MIPs) and non-imprinted polymers (NIPs). Real sample experiments were performed with apple juice. The recognition of Salmonella paratyphi was achieved using these SPR sensor with a detection limit of 1.4 × 10⁶ CFU/mL. In conclusion, SPR sensor has the potential to serve as an excellent candidate for monitoring Salmonella paratyphi in food supplies or contaminated water and clearly makes it possible to develop rapid and appropriate control strategies., Competing Interests: The authors declare no conflict of interest.

The potential of the modified bacterial cellulose (BC) nanofibers was determined bearing metal ion coordination interactions to enhance the protein adsorption and binding capacity. Thus, a household synthesized metal chelating monomer, namely N-methacryloyl-l-histidine methylester (MAH), and a commercial metal chelating monomer, namely 4-vinylimidazole (VIm), were used to complex with metal ions Cu(II) and Ni(II) respectively for the synthesis of the modified BC nanofibers. The modified nanofibers were characterized by FT-IR, SEM and EDX measurements. The protein adsorption tests were carried out using hemoglobin as a model protein and it was determined that the maximum adsorption capacity of hemoglobin onto the modified BC nanofibers was found as 47.40mg/g. The novel strategy for the preparation of metal chelated nanofibers was developed., (Copyright © 2017 Elsevier B.V. All rights reserved.)

Detection of protein C (PC) in human serum was performed by quartz crystal microbalance (QCM) based on molecular imprinting technique (MIP). The high-resolution and mass-sensitive QCM based sensor was integrated with high sensitivity and selectivity of the MIP technique. The PC microcontact imprinted (PC-μCIP) nanofilm was prepared on the glass surface. Then, the PC-μCIP/QCM sensor was prepared with 2-hydroxyethyl methacrylate (HEMA), ethylene glycol dimethacrylate (EGDMA) and N-methacryloyl l-histidine methylester (MAH) as the functional monomer with copper(II) ions. The polymerization was performed under UV light (100W and 365nm) for 20-25min under nitrogen atmosphere. The characterization studies of QCM sensor were done by observation using atomic force microscopy (AFM), contact angle measurements, ellipsometry and fourier transform infrared spectroscopy (FTIR). Detection of PC was investigated in a concentration range of 0.1-30μg/mL. Selectivity of PC-μCIP and PC non-imprinted/QCM (PC-non-μCIP) sensors for PC determination was investigated by using proteins namely hemoglobin (Hb), human serum albumin (HSA) and fibrinogen solutions. QCM sensor was also used for detection of PC molecules in aqueous solutions and human plasma. The detection limit was determined as 0.01μg/mL for PC analysis. The PC-μCIP/QCM sensor was used for five consecutive adsorption-desorption cycles. According to the results, the PC-μCIP/QCM sensor had obtained high selectivity and sensitivity for detection of PC molecules., (Copyright © 2016 Elsevier B.V. All rights reserved.)

The immobilized metal-affinity chromatography (IMAC) has gained significant interest as a widespread separation and purification tool for therapeutic proteins, nucleic acids and other biological molecules. The enormous potential of IMAC for proteins with natural surface exposed-histidine residues and for recombinant proteins with histidine clusters. Cryogels as monolithic materials have recently been proposed as promising chromatographic adsorbents for the separation of biomolecules in downstream processing. In the present study, IMAC cryogels have been synthesized and utilized for the adsorption and separation of immunoglobulin G (IgG) from IgG solution and whole human plasma. For this purpose, Cu(II)-ions were coupled to poly(hydroxyethyl methacrylate) PHEMA using poly(ethylene imine) (PEI) as the chelating ligand. In this study the cryogels formation optimized by the varied proportion of PEI from 1% to 15% along with different amounts of Cu (II) as chelating metal. The prepared cryogels were characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, and thermogravimetric analysis. The [PHEMA/PEI]-Cu(II) cryogels were assayed for their capability to bind the human IgG from aqueous solutions. The IMAC cryogels were found to have high affinity toward human IgG. The adsorption of human IgG was investigated onto the PHEMA/PEI cryogels with (10% PEI) and the concentration of Cu (II) varied as 10, 50, 100 and 150 mg/L. The separation of human IgG was achieved in one purification step at pH7.4. The maximum adsorption capacity was observed at the [PHEMA/PEI]-Cu(II) (10% PEI) with 72.28 mg/g of human IgG. The purification efficiency and human IgG purity were investigated by sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE)., (Copyright © 2016 Elsevier B.V. All rights reserved.)

In this study, thiophilic cryogels were prepared by two different approaches and they were used in purification of IgG from aqueous solutions and human plasma. In the first approach, poly(2-hydoxyethyl methacrylate) [PHEMA] cryogel disks were prepared. The PHEMA cryogel disks were activated by divinylsulfone (DVS) and 2-mercapto ethanol was attached. In the second approach, poly(2-hydroxyethyl methacrylate-etylene glycol dimethacrylate) [P(HEMA-EGDMA)] beads were synthesized and 2-mercapto ethanol was attached to the beads as a thiophilic ligand. In order to increase the surface area, P(HEMA-EGDMA)/PHEMA composite cryogel disks were prepared by embedding the P(HEMA-EGDMA) beads into PHEMA cryogels. Both the thiophilic PHEMA (T-PHEMA) cryogel disks and the thiophilic P(HEMA-EGDMA)/PHEMA [T-P(HEMA-EGDMA)/PHEMA] composite cryogel disks were characterized by Fourier transform infrared spectroscopy, surface area measurements, elemental analysis, swelling tests and scanning electron microscopy. The effects of salt concentration, pH, temperature, initial IgG concentration were analysed for IgG adsorption from aqueous solutions in batch mode. When lyotropic salt, Na2SO4, was used, the adsorption capacity was 27.5 mg/g and 68.7 mg/g for T-PHEMA and the T-P(HEMA-EGDMA)/PHEMA composite cryogel disks, respectively. 1.0 M NaCl was used as desorption agent. The change in adsorption capacity was not remarkable for a repetition of adsorption-desorption cycle ten times. Both the thiophilic cryogel disks and the thiophilic composite cryogel disks were also successfully used for IgG isolation from human plasma. The purity assayed by SDS-PAGE was 89%. The adsorption capacities were 74.8 mg/g and 137.4 mg/g in human plasma samples for the T-PHEMA cryogel disks and the T-P(HEMA-EGDMA)/PHEMA composite cryogel disks, respectively., (Copyright © 2013 Elsevier B.V. All rights reserved.)