Search

Iodine deficiency may cause thyroid dysfunction. The iodine intake in a population is measured by urinary iodine concentration (UIC) in spot samples or 24-h urinary iodine excretion (24UIE). 24UIE is considered the gold standard and may be estimated using an equation including UIC, urinary creatinine concentration, sex and age (e24UIE). The aims of this study were to evaluate the preferable timing of UIC when using this equation and assess the variability of UIE. Sixty healthy non-smoking women (n 31) and men (n 29) were included in Gothenburg, Sweden. Twelve urine samples were collected at six fixed times on two separate days. Variability was calculated for UIC, 24UIE, e24UIE, iodine excretion per hour (iHr) and UIC adjusted for creatinine and specific gravity. Median 24UIE was 156 µg/24 h and the median UIC (all spot samples) was 104 µg/l. UIC (P < 0·001), 24UIE (P = 0·001) and e24UIE (P < 0·001) were significantly higher in men. e24UIE was relatively similar to 24UIE. However, when e24UIE was calculated from UIC in the first void, it was about 15 % lower than 24UIE (P < 0·001). iHr was lowest in the morning and highest in the afternoon. Median iHr was higher in men (7·4 v. 5·3 µg/h, P < 0·001). The variability of UIE was higher within individuals than between individuals. This study suggests that most time points for estimation of individual 24UIE are appropriate, but they should preferably not be collected in the first void.

Employees working in cement production plants are exposed to airborne particulate matter (PM) which may lead to lung function impairments and airway symptoms. The PM consists of raw materials, clinker and additives which vary depending on cement blend. The aim of this work was to characterize the thoracic fraction of PM with regard to size, phase composition and mixing state. Both stationary and personal impactors were used to collect size-fractionated samples in a cement production plant in Norway. Stationary samples were measured with aerosol particle counters and collected with a 13-stage cascade impactor, which were stationed at three locations of the cement production plant: at the raw meal mill, clinker conveyor belt and cement mill. Sioutas cascade impactors, and thoracic and respirable dust samplers were used in parallel for personal sampling. Additionally, particles for electron microscopy were collected with the stationary cascade impactor for size-fractionated single particle characterization. Gravimetric measurements and element compositions of the samples from the stationary impactors show that the PM mass is dominated by calcium-rich particles of size1 μm. The size distribution results of stationary and personal impactors were similar. Characterization of single particles reveals that limestone is the dominating material in the raw meal mill, whereas clinker and limestone dominate at the clinker conveyor belt and at the cement mill. The element composition of clinker PM did not change with particle size. The PM collected on impactor stages with aerodynamic diameter cut-offs below 0.56 μm was dominated by soot and volatile secondary particles at the three locations. The number of ultrafine particles of the cement related compounds was low. Air concentrations of PM in personal respirable and thoracic samples ranged from 0.14-10 mg m

Lead is a non-essential toxic trace element. Lead in blood (BPb) is the most common biomarker of lead exposure but lead in urine (UPb) has also been used. There is, however, limited data on the variability of UPb in the general population and the association with BPb.Our aims were to assess variability of lead in repeated blood and urine samples. The diurnal variation of UPb was also examined as well as associations with BPb.We established an openly available biobank including 60 healthy non-smoking individuals, 29 men and 31 women, 21-64 years of age (median 31 years), with repeated sampling of blood and urine. Timed urine samples were collected at six fixed time points in two 24 h periods, about one week apart, and adjusted for creatinine and specific gravity (SG). BPb and UPb were analyzed by inductively coupled plasma mass spectrometry. The within- and between-individual variabilities and intra-class correlation coefficients (ICCs; ratios of the between-individual to total observed variances) were calculated using mixed-effects models.The ICCs for UPb samples were mostly above 0.5, when adjusted for creatinine or SG, and higher for overnight samples compared with daytime samples. The highest ICCs were obtained for BPb (ICC = 0.97) and for urine samples corrected for dilution by SG or creatinine. The ICC was 0.66 for overnight samples adjusted for creatinine. High correlations with BPb were found for 24 h UPb (rIn addition to BPb, UPb adjusted for creatinine or SG seems to be a useful biomarker for exposure assessment in epidemiological studies.

Objective Ambient exposure to fine particles is associated with increased cardiovascular morbidity and mortality. Associations between occupational particulate matter (PM) exposure and cardiovascular disease have been studied less. The objective of this study was to examine associations between PM exposure and endothelial function among workers in Norwegian smelters. Methods We examined endothelial function with Endo-PAT equipment after a working day (WD) and on a day off (DO) in 59 furnace workers recruited from three metal smelters in Norway. The difference in baseline pulse amplitude (BPA) and reactive hyperemia index (RHI) between the 2 days was analysed in relation to individual exposure to PM 250) or the respirable aerosol fraction of particles, and adjusted for relevant covariates. Results The exposure to PM250 ranged from 0.004 to 5.7 mg/m3. The mean BPA was significantly higher on WD relative to DO (772 vs. 535, p = 0.001). This difference was associated with PM concentrations among participants ≥ 34 years, but not among the younger workers. Reactive hyperemia was significantly lower on workdays relative to days off (1.70 vs. 1.84, p = 0.05). This difference was observed only among participants above the age 34. No associations with PM exposure were observed. Conclusions PM exposure was associated with higher BPA among participants older than 34 years. BPA reflects microvessel pulsatility. Our results may indicate an age-dependent cardiovascular susceptibility to PM exposure. Endothelial function measured by RHI was reduced on WD among participants 34 years and older, but we found no associations between PM exposure and RHI.

While exposure to air contaminants from metal arc welding at workplaces has been intensively investigated over the last five decades, other hot work processes, such as flame and plasma cutting, air carbon arc gouging, and surface grinding have not received as much attention. Exposures to particulate matter (PM) during selected hot work processes, such as metal active gas (MAG) and manual metal arc (MMA) welding, flame and plasma cutting, air carbon arc gouging, and surface grinding were measured. Respirable, inhalable, and "total" fractions of the PM were collected with different air samplers in the workers' breathing zone. Concentrations of PM, chromium (Cr), iron (Fe), manganese (Mn), molybdenum (Mo), nickel (Ni), copper (Cu), and lead (Pb) were determined in the samples by using gravimetric analysis and plasma-based analytical atomic spectrometry techniques. Bio-accessibility of the elements was investigated by using a synthetic lung lining fluid (Hatch´s solution) for the leaching of soluble metal compounds in the collected samples. Short term (15-75 min) workplace air concentrations of PM, Cr, Fe, Mn, Ni and Cu in the workers´ breathing zone during hot work processes were found to be high compared to the current 8-hr time-weighted average (TWA) exposure limit values (ELVs) in use in many countries. The short-term median concentrations of PM during the different hot work processes varied between 6.0 and 88.7 mg m

The aim of this study was to characterise particulate matter (PM) collected in the furnace area during SiMn and high carbon (HC)-FeMn production in terms of single particle analysis and to determine the bioaccessibility of Mn in the PM in a simulated lung fluid. Airborne PM was collected with Sioutas cascade impactors and respirable cyclones in the breathing zone of tappers and crane operators. Stationary samples were collected from the furnace area with a nanoMOUDI cascade impactor and an ESPnano electrostatic particle collector. Individual particles were characterised by scanning and transmission electron microscopy. Bioaccessibility of Mn was studied in terms of the dissolution of Mn in Gamble solution (24 hours leaching at 37 °C) relative to total Mn. Slag particles, alloy fragments, Mn and Fe oxides as well as carbonaceous particles were observed in the size fraction > 1 μm aerodynamic diameter (dae). Thermally generated condensation particles dominated the dae size range of 0.18-1 μm collected from the tapping fumes, while carbonaceous particles dominated the fraction below 0.18 μm. Condensation generated particles from the furnace area of HC-FeMn production were coated with an amorphous Si-O rich surface layer which seemed to hold primary particles together as aggregates. In the same size range, the particles from the furnace area of SiMn production were dominated by spherical condensation particles rich in Si, Mn and O, but without a Si-O rich surface layer. Instead, the Mn oxides were enclosed in an amorphous Si-O rich matrix. The bioaccessibility of Mn was low to moderate (

The aims of this study were to assess serum concentrations of per- and polyfluoroalkyl substances (PFASs) in selected populations from Ghana, including workers engaged in the repair of electronic equipment (ERWs), and to elucidate PFAS concentrations in relation to blood mercury concentrations (B-Hg) as a biomarker of seafood consumption. In all, 219 participants were recruited into the study, of which 26 were women and 64 were ERWs. Overall, the PFAS concentrations were low. The most abundant components were perfluorooctane sulfonate (PFOS) and perfluorohexane sulfonic acid (PFHxS). Women had generally lower PFAS concentration than men. The ERWs had statistically significantly higher concentrations of perfluorooctanoate (PFOA), which was associated with the concentration of tin in urine. This could indicate exposure during soldering. The concentration of B-Hg was associated with several of the PFASs such as PFOA, PFOS and perfluoroheptane sulfonate (PFHpS). Additionally, the concentrations of perfluorodecanoic acid (PFDA) and perfluoroundecanoate (PFUnDA) were highly associated with the concentrations of B-Hg. It is noteworthy that the linear isomer of PFHxS was strongly associated with B-Hg while the branched isomers of PFHxS were not. In conclusion, the PFAS concentrations observed in the present study are low compared to other populations previously investigated, which also reflects a lower PFAS exposure within the Ghanaian cohorts. ERWs had significantly higher PFOA concentrations than the other participants. Several PFASs were associated with B-Hg, indicating that seafood consumption may be a source of PFAS exposure.

The global SiC market is projected to grow in the coming years, and research on potential health effects as well as epidemiological studies is therefore of importance. A detailed characterization in terms of the phase composition, morphology and mixing state of airborne PM is still missing, though highly necessary to identify sources and to understand the risk factors in this industry. Particles in the size range of 10 nm to 10 µm were collected with a 13-stage NanoMOUDI impactor in the Acheson Furnace Hall as well as in processing departments during two sampling campaigns. Particle mass concentrations, including the fraction of ultrafine particles (UFPs), were lower in the processing departments in comparison to those in the Acheson Furnace Hall. The particle number size distribution measured with a scanning mobility particle sizer confirmed the low amount of UFPs in the processing departments compared to the furnace hall. Significant differences in the particle mass concentration and distribution were observed in the Acheson Furnace Hall during the two sampling campaigns. The PM size distribution depends upon the sampling location, on the cycle of the nearby furnaces and on special incidents occurring during a furnace run. Scanning and transmission electron microscopy (SEM and TEM) showed that the size range of 0.32-10 µm (aerodynamic diameter) is dominated by carbon (C)-rich particles, which were identified as petroleum coke, graphite, soot and amorphous spherical C-rich particles. Soot was further classified into three types based on the primary particle size, morphology and composition. Diesel-powered vehicles, pyrolysis of petroleum coke and incomplete combustion of volatile components from this pyrolysis are suggested as sources of different soot particle types. Amorphous spherical C-rich particles were also sub-classified based on their morphology and composition as tar balls (TBs) and C-spherical type 2. The amount of SiC fibers and crystalline SiO2 was found to be low. In the size fraction below 0.32 µm (aerodynamic diameter), sulphur (S)-rich particles dominate. This knowledge of the particle size distribution, and chemical and physical properties of the PM occurring in the SiC production is fundamental for an appropriate risk assessment, and these findings should have implications for future epidemiological studies and for the mitigation of worker exposure.

Introduction Shotgun pellets containing bismuth (Bi) as substitute for lead (Pb) are increasingly being used due to environmental concerns. Information on toxicokinetics of Bi is lacking for the assessment of humans accidentally shot by Bi-containing shotgun alloy pellets. Methods Male Wistar rats were exposed to miniature alloy pellets containing Bi, tin (Sn) and minor amounts of Pb by implantation in muscle tissues of the hind legs. Results The concentrations of Bi in whole blood and urine increased up to 53 weeks after implantation. The highest concentrations of Sn in whole blood were observed three weeks after implantation, then declining to background levels 53 weeks after implantation. Lead in whole blood increased up to 13 weeks of exposure, and declined for the remaining observation period. Bismuth and Sn accumulated mainly in kidney, but also in liver, testicle and brain. Analytical field emission scanning electron microscopy of post-implant pellets showed depletion of Pb towards the pellet surface. Oxygen and chlorine accumulated in Sn rich lamellas in areas next to the pellet surface. The distribution of Bi remained visually unaffected as compared to pre-implant pellets. Conclusion The concentration of Bi increased during the whole observation period in blood, urine, kidney, brain, testicle and liver. The decline in the concentrations of Pb and Sn in blood and urine after reaching the peak concentration may be related to alterations in the chemical composition and element distribution of the implanted alloy pellets.

Silicon carbide (SiC) is largely used in various products such as diesel particulate filters and solar panels. It is produced through the Acheson process where aerosolized fractions of SiC and other by-products are generated in the work environment and may potentially affect the workers’ health. In this study, dust was collected directly on a filter in a furnace hall over a time period of 24 h. The collected dust was characterized by scanning electron microscopy and found to contain a high content of graphite particles, and carbon and silicon containing particles. Only 6% was classified as SiC, whereof only 10% had a fibrous structure. To study effects of exposure beyond the respiratory system, neurotoxic effects on human astrocytic cells, were investigated. Both low, occupationally relevant, and high doses from 9E-6 mg/cm2 up to 4.5 mg/cm2were used, respectively. Cytotoxicity assay indicated no effects of low doses but an effect of the higher doses after 24 h. Furthermore, investigation of intracellular reactive oxygen species (ROS) indicated no effects with low doses, whereas a higher dose of 0.9 mg/cm2 induced a significant increase in ROS and DNA damage. In summary, low doses of dust from the Acheson process may exert no or little toxic effects, at least experimentally in the laboratory on human astrocytes. However, higher doses have implications and are likely a result of the complex composition of the dust. © 2017 The Author(s). Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND

Individual soot agglomerates collected at four different locations on the Arctic archipelago Svalbard (Norway) were characterised by transmission electron microscopy and energy-dispersive X-ray microanalysis. For source identification of the ambient soot agglomerates, samples from different local sources (coal burning power plants in Longyearbyen and Barentsburg, diesel and oil burning for power generation in Sveagruva and Ny Alesund, cruise ship) as well as from other sources which may contribute to Arctic soot concentrations (biomass burning, aircraft emissions, diesel engines) were investigated. Diameter and graphene sheet separation distance of soot primary particles were found to be highly variable within each source and are not suited for source identification. In contrast, concentrations of the minor elements Si, P, K, Ca and Fe showed significant differences which can be used for source attribution. The presence/absence of externally mixed particle groups (fly ashes, tar balls, mercury particles) gives additional hints about the soot sources. Biomass/wood burning, ship emissions and coal burning in Barentsburg can be excluded as major source for ambient soot at Svalbard. The coal power plant in Longyearbyen is most likely a major source of soot in the settlement of Longyearbyen but does not contribute significantly to soot collected at the Global Atmosphere Watch station Zeppelin Mountain near Ny Alesund. The most probable soot sources at Svalbard are aircraft emissions and diesel exhaust as well as long range transport of coal burning emissions.

Background Urine is often used for biomonitoring the exposure to elements. However, most studies report concentrations in spot urine samples, which may not accurately mirror the “gold standard” of complete 24-h (24 h) urine samples. There are relatively few data published for 24 h samples, and little information on the within- and between person variability. Objectives The present study aimed at assessing variability within and between individuals in 24 h excretion for a number of elements in adults from the general population and the typical 24 h excretion of these elements. In addition, we assessed concentrations adjusted for creatinine and specific gravity (SG), and associations between elements. Methods 60 healthy non-smokers (31 women and 29 men) from Sweden, aged 21–64 years, collected all urine during 24 h (split into six separate samples) on two occasions, about one week apart. Concentrations of As, Br, Cd, Co, Cr, Cu, Fe, Hg, Li, Mn, Mo, Ni, P, Pb, S, Sb, Se, Sn, U, V, W, and Zn in urine were analyzed by inductively coupled plasma sector-field mass spectrometry (ICP-SF-MS) and 24 h excretion rates were calculated for each day. The ratio of between-individual variance and the total variance, the intra-class correlation (ICC) was calculated based on natural log-transformed 24 h excretion. Correlation coefficients were calculated between excretion rates (mass/24 h), and concentrations adjusted for creatinine and SG. Results Geometric means (GM), and 90-percentiles are presented for each element. The 24 h excretion was higher in men than in women for most elements, and the difference was statistically significant for Cr, Cu, Fe, Li, P, Pb, S, Se, U, V, and Zn. However, for Cd and Co, the excretion was higher in women. Variability between days was low for Cd, Co, Hg, Pb, Sn, Se, V, and Zn (ICC 0.75–0.90), highest for Cr (ICC = 0.3) and Sb (ICC = 0.18), and moderate for the other elements. Spearman's rank correlation coefficients were about 0.8–0.9 for 17 elements, and 0.3–0.7 for Br, Cu, P, S, Se. Excretion of P and S were highly correlated, and also associated with excretion of most of the other elements, especially Cu, Se, V, and Zn. A high correlation was also found between As and Hg, between Mo and W, as well as between Cr, Fe and Mn. Conclusions These data present normal variability of 24 h excretion of a number of elements, and can also be used as updated reference levels for elements with no or limited previous literature available. Information on variability within- and between individuals is important to know when designing studies with urine levels of elements used as exposure biomarker in studies of associations with health outcomes.

The bio-accessibility of 14 elements in welding fume particulate matter was investigated in 325 personal air samples collected during welding in two shipyards and one factory producing heavy machinery. The apparent solubility in a synthetic lung lining fluid (Hatch's solution) was used as proxy for the bio-accessibility. The Hatch solubility of the different elements was highly variable with a median < 1% for Al, Fe, Pb, Ti, between 4 and 6% for Co, Cr, Ni, V, W, between 13 and 27% for Cd, Cu, Mn, Zn, and 41% for Mo. For many elements, the solubility varied over a wide range of several tens of percent. The welding techniques used influenced the solubility of Co, Cr, Cu, Mn and V significantly. The plants investigated (i.e., the welded materials and used electrodes) had a significant influence on the solubility of Co, Cr, Cu, Mn, Mo, V and W. According to principal component analysis (PCA), the variation in solubility can be described by four components, which explain 69% of the variance. The first principal component mostly comprises elements that can predominantly occur as divalent cations, the second principal component elements often forming oxyanions. The principal components are independent of the absolute value of the Hatch solubility. The results of PCA indicate that the co-variation of Hatch solubility is mainly controlled by the most soluble compounds in contrast to the absolute value of apparent solubility, which is strongly influenced by the distribution of the elements between compounds with different equilibrium solubilities. The observed large variability and the significant differences between welding techniques and plants clearly show that the bio-accessibility cannot be obtained from the literature but has to be studied experimentally at each location of interest.

Studies have shown that welders have increased cardiovascular mortality. This may be due to airborne particulate matter (PM) exposure. Elevated levels of PM in polluted urban air have been associated with increased cardiovascular mortality and morbidity. This study seeks to explore potential mechanisms for the increased cardiovascular mortality in welders. Seventy welders were compared to 74 referents. Exposure to PM was assessed by personal full-shift sampling of work room air the last 2 days before collection of blood samples. Selected biomarkers of pro-coagulant activity, endothelial/platelet activation and systemic inflammation were determined in the samples. The welders had been occupationally exposed to PM for 15 years on average. The geometric mean current exposure to PM was 8.1 mg/m3. They had statistically significantly higher concentrations of TNF-α, P-selectin, CD40L, prothrombin fragment 1 + 2 and d-dimer than the referents. Increasing concentrations of d-dimer and CD40L were observed by increasing current exposure to PM. The study shows that welders highly exposed to welding PM were in a pro-thrombotic state with increased thrombin generation and consequently higher d-dimer concentrations. The welders had also increased endothelial/platelet activation as compared to the referents. These alterations are compatible with increased cardiovascular mortality as previously reported among welders.

The emission of ultrafine carbonaceous particles during the laser cutting of fiber-reinforced polymer (CFRP) composite materials was investigated. The study was based on characterization of air contaminants emitted during laser cutting of an epoxy-based CFRP material with respect to particle size distribution, particle morphology, and chemical composition. Results indicate that about 90% of the total particulate mass is present as fine particulate matter with an aerodynamic cut-off diameter of 0.25 μm, and considerable amounts of ultrafine carbonaceous particulate matter dominated by organic carbon are emitted during high-power laser cutting of CFRP.

Elemental carbon (EC) and nitrogen dioxide (NO2) in air as markers for diesel exhaust (DE) emission exposure were measured in selected work environments in Norway where diesel-powered engines are in use. Two hundred and ninety personal full-shift air samples were collected in primary aluminium production, underground and open-pit mining, road tunnel finishing, transport of ore, and among airport baggage handlers. EC was determined in the samples by a thermo-optical method, while NO2 was determined by ion chromatography. Highest EC air concentrations (geometric mean, GM) were found in aluminium smelters (GM = 45.5 μg m-3) followed by road tunnel finishing (GM = 37.8 μg m-3) and underground mining activities (GM = 18.9 μg m-3). Low EC air concentrations were measured for baggage handling at an international airport (GM = 2.7 μg m-3) and in an open-pit mine (GM = 1.2 μg m-3). Air concentrations of NO2 were similar in road tunnel finishing (GM = 128 μg m-3) and underground mining (GM = 108 μg m-3). Lower NO2 values were observed in open-pit mining (GM = 50 μg m-3), at the airport (GM = 37 μg m-3), and in the aluminium smelters (GM = 27 μg m-3). Highly significant (P < 0.001) positive correlations between NO2 and EC air concentrations in underground mining (r = 0.54) and road tunnel finishing (r = 0.71) indicate a common source of these pollutants. NO2 and EC were also correlated (P < 0.01) positively at the airport. However, due to the complex air chemistry and a potential contribution of various sources, the correlation between EC and NO2 cannot be regarded as unambiguous hint for a common source. The association between EC and NO2 was not of statistical significance in open-pit mining. In the aluminium smelters, EC and NO2 were negatively correlated, although not reaching statistical significance. The substantial differences in NO2/EC ratios across the investigated industries, ranging from around 0.2 in the primary aluminium production to around 25 during spring at the airport, clearly show that exposure to DE cannot be estimated based on NO2 concentrations, at least for outdoor environments. Results in the primary aluminium production suggest that the measured EC concentrations are related to DE emissions, although the NO2 concentrations were low. Further studies are required to assess the magnitude of exposure in primary aluminium production.

Introduction Exposure to fine particulate matter in urban air has been associated with increased risk of hospitalisation and death from cardiovascular diseases. One hypothesis suggests a direct influence of particles on the autonomic nervous system. Some studies have shown an association between particle exposure and reduced heart rate variability (HRV). Furnace workers in metal smelters are occupationally exposed to fine and ultrafine particles. The aim of this study was to examine the association between exposure to particulate matter in metal smelters and HRV. Methods We examined 64 workers in three Norwegian metal smelters on a working day, and on a day off after at least two days since last exposure. On the working day, exposure to different particle size fractions was assessed by personal sampling, using respirable cyclones and five-stage Sioutas cascade impactors. The workers carried Holter monitors for 24 hours’ heart rate registration during the working day and the day off. HRV indices were analysed by exposure for each hour of the day, using mixed model regression, adjusted for relevant covariates. Results There were 58 male and 6 female workers. Their mean age was 34 years (range 19–64). The mean exposure to respirable particulate matter was 2.36 mg/m3, while 0.88 mg/m3 was below 250 nm. Standard deviation of normal-to-normal intervals (SDNN) was reduced during working hours on the working day relative to the day off, whereas in the afternoon and night hours there were no significant differences. Low frequency/high frequency (LF/HF) ratio was higher during working hours on the working day, but in the afternoon and evening hours the LF/HF ratio was significantly higher on the day off compared to the working day. Conclusion HRV indices differ between working day and day off. Analyses are in progression, and further results on the effects of particle exposure will be presented.

A novel analytical procedure was developed for the simultaneous speciation analysis of chromate, molybdate, tungstate and vanadate by anion-exchange high performance liquid chromatography hyphenated to inductively coupled plasma mass spectrometry (HPLC-ICP-MS). Linear gradient elution from 100% water to 100% 0.7 M NaCl was applied for chromatographic separation of metal species. In standard aqueous solution at neutral pH molybdate, tungstate and vanadate exist in several aqueous species, while chromate is present as a single CrO4(2-) species. Consequently, only chromate can be separated from this solution in a sharp chromatographic peak. For obtaining sharp chromatographic peaks for molybdate, tungstate and vanadate, the pH of aqueous standard solutions was raised to 12. At highly alkaline conditions single CrO4(2-), MoO4(2-) and WO4(2-) are present and were eluted in sharp chromatographic peaks, while VO4(3-) species, which predominates at pH 12 was eluted in slightly broaden peak. In a mixture of aqueous standard solutions (pH 12) chromate, molybdate, tungstate and vanadate were eluted at retention times from 380 to 420 s, 320 to 370 s, 300 to 350 s and 240 to 360 s, respectively. Eluted species were simultaneously detected on-line by ICP-MS recording m/z 52, 95, 182 and 51. The developed procedure was successfully applied to the analysis of leachable concentrations of chromate, molybdate, tungstate and vanadate in alkaline extracts (2% NaOH+3% Na2CO3) of manual metal arc (MMA) welding fumes loaded on filters. Good repeatability and reproducibility of measurement (RSD±3.0%) for the investigated species were obtained in both aqueous standard solutions (pH 12) and in alkaline extracts of welding fumes. Low limits of detection (LODs) were found for chromate (0.02 ng Cr mL(-1)), molybdate (0.1 ng Mo mL(-1)), tungstate (0.1 ng W mL(-1)) and vanadate (0.2 ng V mL(-1)). The accuracy of analytical procedure for the determination of chromate was checked by analysis of CRM 545, Cr(VI) in welding dust loaded on a filter. Good agreement between determined and reported certified values was obtained. For molybdate, tungstate and vanadate the assessment of accuracy was performed by spiking welding fume filters. Good recoveries for all investigated species (98-101%) confirmed the accuracy of the analytical procedure.

This paper discusses the combined use of electron backscatter diffraction (EBSD) and energy dispersive X-ray microanalysis (EDX) to identify unknown phases in particulate matter from different workplace aerosols. Particles of α-silicon carbide (α-SiC), manganese oxide (MnO) and α-quartz (α-SiO2) were used to test the method. Phase identification of spherical manganese oxide particles from ferromanganese production, with diameter less than 200 nm, was unambiguous, and phases of both MnO and Mn3O4 were identified in the same agglomerate. The same phases were identified by selected area electron diffraction (SAED) in transmission electron microscopy (TEM). The method was also used to identify the phases of different SiC fibres, and both β-SiC and α-SiC fibres were found. Our results clearly demonstrate that EBSD combined with EDX can be successfully applied to the characterisation of workplace aerosols.

Background Lead battery repair workers (LBRW) and electronic repair workers (ERW) may be exposed to inorganic components during work. This study aimed at determining essential and non-essential trace elements in male LBRW, ERW, referents and a group of female petty traders (FPT) in Kumasi (Ghana), taking into account iron status and inflammation. Methods Altogether 64 LBRW, 64 ERW, 65 referents and 26 FPT were investigated in this cross-sectional study. Urine, whole blood and serum were collected for determination of trace elements. C-reactive protein and ferritin were determined in serum. Results The LBRW had higher blood concentrations of manganese (B-Mn) and lead (B-Pb) and antimony in urine (U-Sb), and lower concentrations of cobalt in blood (B-Co). Being ERW was associated with higher concentrations of blood cadmium (B-Cd), urinary tin (U-Sn) and serum chromium (S-Cr). Concentrations of selenium (B-Se), Co and mercury (B-Hg) in whole blood and iodine in urine (U-I) were relatively high. Marginal iron status appeared to be a determinant for elevated concentrations of Co in particular, but also Mn and Cd in blood. Systemic inflammation was associated with the concentrations of copper and Se. The concentrations of Hg in whole blood were highly associated with Se and arsenic (As) in whole blood, indicating fish consumption as a common source of intake of these elements. However, Hg in whole blood was only slightly associated with Se in serum. Conclusions The ERW had elevated concentrations of B-Cd, S-Cr, and U-Sn, while B-Mn, B-Pb, and U-Sb concentrations were higher among the LBRW. Iron status and inflammation had substantial impact on some element concentration. This population had high concentrations of B-Se, B-Hg and B-Co and U-I.

Ambient air pollution is associated with increased incidence and mortality of cardiovascular disease. Time-series studies have shown that a 10 µg/m3 increase in mean 24 hour PM2 concentration increases the relative risk for daily cardiovascular mortality by 0.4% to 1.0%. In recent years, increasing concerns have been levelled at the ultrafine component of PM. Ultrafine particles are formed during combustion of materials, and are therefore abundant in the furnace area of metal smelter plants. In connexion with an ongoing project concerning occupational exposure to fine and ultrafine particles and risk of cardiovascular disease, an update of two large smelter worker cohorts has been performed. Mortality data were received from the Norwegian Causes of Death register for the period 1960–2014. The combined cohort consisted of 19 660 men, with nearly 650 000 person-years of follow-up. Preliminary analyses showed that both total mortality (SMR 1.09, 95% CI 1.07–1.11) and mortality from all cardiovascular diseases (SMR 1.03, 95% CI 1.00–1.06) were significantly increased compared to the Norwegian general male population. Workers with employment in furnace work had total mortality SMR 1.18 (95% CI 1.15–1.21) and cardiovascular mortality SMR 1.09 (95% CI 1.04–1.14). Smelter workers with no furnace work had total mortality SMR 1.01 (95% CI 0.99–1.04) and cardiovascular SMR 0.99 (95% CI 0.95–1.02). The further data analyses are currently in progress.

Source at http://dx.doi.org/10.1038/ejcn.2017.83 BACKGROUND/OBJECTIVES: Iodine deficiency during pregnancy may influence maternal and foetal thyroid function with the risk of causing neurocognitive and psychomotor deficits in the offspring. The objective of this study was to assess iodine status in pregnant women from Northern Norway and to investigate the influence of iodine status on maternal and infant thyroid function. SUBJECTS/METHODS: Women from the Northern Norway Mother-and-Child contaminant Cohort Study (MISA) donated a blood and urine sample at three visits during their pregnancy and postpartum period (in second trimester, 3 days and 6 weeks after delivery. N = 197). Women were assigned to iodine status groups according to urine iodine concentrations (UICs) in second trimester and mixed effects linear models were used to investigate potential associations between iodine status and repeated measurements of thyroid-stimulating hormone (TSH), thyroid hormones (THs), TH-binding proteins and thyroid peroxidase antibodies. Associations between maternal iodine status and TSH in heel prick samples from the infants were investigated with linear regression. RESULTS: Median UIC in second trimester was 84 μg/l (range 18–522) and 80% had UIC below recommended level (o150 μg/l). Iodine-deficient women had higher concentrations of T3, FT3 and FT4 (estimated differences (confidence intervals) of 0.10 nmol/l (0.01, 0.17), 0.16 pmol/l (0.05, 0.26) and 0.45 pmol/l (0.10, 0.78), respectively) compared with iodine-sufficient women. The concentrations varied within normal reference ranges, but the majority of women with subclinical hypothyroidism were iodine deficient. Maternal iodine status did not influence infant TSH concentrations. CONCLUSIONS: This study indicate iodine deficiency among pregnant women in Norway. Iodine status during pregnancy influences maternal thyroid homeostasis and is therefore a risk factor for foetal and infant development.

The bioaccessibility of Pb in air particulate matter from two car battery repair workshops in Kumasi (Ghana) was measured (64 full shift personal aerosol samples). An artificial lung lining fluid simulant (Hatch solution) was applied for leaching the bioaccessible fraction in half of the samples, the other half was leached with synthetic gastric juice. At both locations, the Pb solubility (median) in gastric juice (89% and 92%) is substantially higher than in Hatch solution (4.9% and 5.6%). The high solubility of Pb in gastric juice may be related to the presence of Pb oxides. The low bioaccessibility of Pb in Hatch solution is in good agreement with previous work on mine tailings, urban aerosol, car exhaust, welding fumes and indoor dust. The high bioaccessibility of Pb in the gastrointestinal tract underpins the importance of improving the personal hygienic behavior at the workplace. It is recommended that air monitoring of Pb should include the extrathoracic aerosol fraction using inhalable aerosol samplers, as particles of this size fraction are most likely transferred to the gastrointestinal tract in addition to the non-lung-soluble particles transported from the lung by mucociliary and phagocytosis clearance.

Background Welders are exposed to a number of metallic elements during work. Bioaccessability, that is important for element uptake, has been little studied. This study addresses bioaccessability and uptake of chromium (Cr), molybdenum (Mo), tungsten (W) and vanadium (V) among welders. Methods Bioaccessability of Cr, Mo, V and W was studied in airborne particulate matter collected by personal sampling of the workroom air among shipyard welders by using the lung lining fluid simulant Hatch solution. Associations between concentrations of Hatch soluble and non-soluble elements (Hatchsol and Hatchnon-sol) and concentrations of the four elements in whole blood, serum, blood cells and urine were studied. Results Air concentrations of the four elements were low. Only a small fraction of Cr, V and W was Hatchsol, while similar amounts of Mo were Hatchsol and Hatchnon-sol. Welders (N = 70) had statistically significantly higher concentrations of all four elements in urine and serum when compared to referents (N = 74). Highly statistically significant associations were observed between urinary W and Hatchsol W (p Conclusions Associations between Hatchsol elements in air and their biological concentrations were higher than when Hatchnon-sol concentrations were considered. Associations were generally higher when air samples collected the day before biological sampling were considered as compared to air samples collected two days before.

Objectives Exposure to fine particles (PM2.5) in urban air has been associated with increased risk of hospitalisation and death from cardiovascular diseases. The endothelium is an important transmitter of signals in the cardiovascular system, and dysfunction of the endothelium is an early marker of increased risk of cardiovascular disease. Workers in metal smelters are occupationally exposed to fine and ultrafine particles in a much higher concentration than from levels in the polluted urban air. Few studies of cardiovascular effects from fine particles have been performed in a working environment. The aim of this study was to examine the association between exposure to different particle size fractions in manganese smelters and endothelial function. Methods We examined 40 workers in two Norwegian manganese smelters after a working day in the furnace hall, and after at least two consecutive days off work. On the working day, exposure to different particle size fractions was assessed with personal sampling using respirable cyclones and five-stage Sioutas cascade impactors. Endothelial function measured with Endo-PAT2000 (Itamar Medical Ltd.). Associations between the mass of different particle size fractions and endothelial function were assessed using mixed model regression. Results Reactive hyperemia index (LnRHI) was reduced with increasing levels of particles in the three finest fractions ( Conclusion Exposure to fine particles in the manganese industry is associated with reduced endothelial function.

Physicochemical properties important in exposure characterisation of four different welding aerosols were investigated. Particle number size distributions were determined by scanning mobility particle sizer (SMPS), mass size distributions by separation and weighing the individual size fractions of an 11-stage cascade impactor. The size distribution of the primary particles of agglomerates, chemical composition and morphology of the particles were examined by TEM. There were significant differences in the particle number size distributions of the different welding aerosols according to the SMPS determinations. The particle mass size distributions determined gravimetrically were, however, not really different. The dominant range with respect to mass was between 0.1 and 1 μm, regardless of the welding technique. Most of the primary particles in all different welding aerosols had diameters between 5 and 40 nm. All types of primary particles had a tendency to form chainlike agglomerates. A clear size dependence of the particle chemical composition was encountered in the case of manual metal arc welding aerosol. Small particles with diameters below 50 nm were mostly metal oxides in contrast to larger particles which also contained more volatile elements (e.g. potassium, fluorine, sodium, sulphur).

Air samples were collected by personal sampling with five stage Sioutas cascade impactors and respirable cyclones in parallel among tappers and crane operators in two manganese (Mn) alloy smelters in Norway to investigate PM fractions. The mass concentrations of PM collected by using the impactors and the respirable cyclones were critically evaluated by comparing the results of the parallel measurements. The geometric mean (GM) mass concentrations of the respirable fraction and the

Sources of C-rich particles at work places in two aluminium smelters in Norway were studied by transmission electron microscopy and energy-dispersive X-ray microanalysis. Based on morphology, nanostructure and chemistry, three different types of C-rich particles are distinguished: (a) chain-like agglomerates (70-100% by number, relative to the sum of C-rich particles) consisting of primary particles with typical onion-shell structure of graphene layers, (b) multi-walled carbon nanotube particles (≈3%) and (c) spheres or agglomerates of amorphous C-rich particles (0-30%). Chain-like agglomerates are interpreted as diesel soot in accordance with literature data on primary particle diameter, chemical composition and nanostructure of primary particles. The source of the observed multi-walled carbon nanotubes is not known. The amorphous C-rich particles most likely consist of organic carbon species which cannot be characterized further by X-ray microanalysis. Unaltered graphitic electrode material was not found among the C-rich particles. The high fraction of diesel soot particles indicates that elemental carbon is generally suited as proxy for diesel soot in aluminium smelters. However, due to the presence of carbon nanotubes and amorphous C-rich particles, detailed characterization of sources of carbon-rich particles by electron microscopy is recommended for accurate assessment of adverse health effects.

Lanthanum (La) is a nonessential element. In its pure form, it is a rather soft, silvery-white metal, which tarnishes rapidly in air. Its atomic weight is 138.9055 and its atomic number is 57. Rare earth elements including La are relatively abundant in the Earth’s crust, but finding them where they can be economically mined and processed presents a challenge. China is presumed to be responsible for over 95% of the world’s mine production. The chemistry of La primarily concerns its formation of the ionic +3 oxidation state. Lanthanum oxide improves the alkali resistance of glass: it is used in making special optical glasses, such as infrared-absorbing glass, as well as camera and telescope lenses, because of the high refractive index and the low dispersion of rare earth glass. Small amounts of lanthanum added to steel improve its malleability. Microelement fertilizers with lanthanum as a main component have been used in Chinese plant production for about 30 years to improve yield and quality. In the general population the mean dietary intake of La and lanthanides is estimated to be below 150 μg, which is less than 5% of the estimated acceptable daily intake. Lanthanum in drinking water samples is reported to be below 10 μg/L. Lanthanum carbonate as a drug was approved for human use by the U.S. Food and Drug Administration in 2004 and by the European Union in 2006 to reduce serum phosphate levels in chronic kidney failure. For its administration to patients with end-stage renal failure, the lanthanum salt is given in the form of chewable tablets, at a maximal dose of 3000 mg per day. The absorption of La salts from the gut, as well as from the lungs, of humans is negligible or very small. Few side effects have been reported after oral intake of lanthanum carbonate as a drug. Gastrointestinal disturbances such as diarrhea, vomiting, and abdominal pain may occur. Myalgia, hypotension, and occasional cases of mental confusion have also been reported. Therapeutic administration of lanthanum salt will interact with the absorption of some other drugs, since the lanthanum cation can react with anionic forms of some compounds such as tetracyclines and quinolones.

Blood and urine samples for determination of manganese (Mn) and iron (Fe) concentrations were collected in a cross-sectional study of 137 currently exposed welders, 137 referents and 34 former welders. Aerosol samples for measurements of personal air exposure to Mn and Fe were also collected. The aerosol samples were assessed for their solubility using a simulated lung lining fluid (Hatch solution). On average 13.8% of the total Mn mass (range 1-49%; N = 237) was soluble (Hatch sol), while only 1.4% (0.1-10.0%; N = 237) of the total Fe mass was Hatch sol. The welders had statistically significantly higher geometric mean concentrations of Mn in whole blood (B-Mn 12.8 vs. 8.0 μg L (-1)), serum (S-Mn 1.04 vs. 0.77 μg L(-1)) and urine (U-Mn 0.36 vs. 0.07 μg g (-1) cr.) than the referents. Statistically significant univariate correlations were observed between exposure to Hatch sol Mn in the welding aerosol and B-Mn, S-Mn and U-Mn respectively. Pearson's correlation coefficient between mean Hatch sol Mn of two days preceding the collection of biological samples and U-Mn was 0.46 (p0.001). The duration of employment as a welder in years was also associated with B-Mn and S-Mn, but not with U-Mn. Statistically significantly higher U-Mn and B-Mn were observed in welders currently exposed to even less than 12 and 6 μg m (-3) Hatchsol Mn, respectively. When using the 95(th) percentile concentration among the referents as a cut-point, 70.0 and 64.5% of the most highly exposed welders exceeded this level with respect to B-Mn and U-Mn. The concentrations of B-Mn, S-Mn and U-Mn were all highly correlated in the welders, but not in the referents.

In recent years, bismuth has been promoted as a “green element” and is used as a substitute for the toxic lead in ammunition and other applications. However, the bioavailability and toxicity of bismuth is still not very well described. Following a hunting accident with bismuth-containing shots, a bioavailability study of bismuth from metal pellets inoculated into rat limb muscles was carried out. Bismuth could be found in urine and blood of the animals. Bio-imaging using laser ablation ICP-MS of thin sections of the tissue around the metal implant was carried out to find out more about the distribution of the metal diffusing into the tissue. Two laser ablation systems with different ablation cell designs were compared regarding their analytical performance. Low concentrations of bismuth showing a non-symmetrical pattern were detected in the tissue surrounding the metal implant. This was partly an artefact from cutting the thin sections but also bio-mobilisation of the metals of the implant could be seen. An accumulation of zinc around the implant was interpreted as a marker of inflammation. Challenges regarding sample preparation for laser ablation and bio-imaging of samples of diverse composition became apparent during the analysis.

A recently developed novel portable real-time hydrogen fluoride spectrometer was used with an aerosol PM10 spectrometer under a PIMEX telemetric measurement strategy to visualize and identify simultaneous occupational air peak exposure events to hydrogen fluoride and PM10 aerosol sub-fractions in aluminium smelter pot rooms using Søderberg or Prebake anode technologies. The hydrogen fluoride and the aerosol concentration data measured during different work operations are plotted and evaluated applying the synchronised videos and air concentrations measured by the spectrometers. The main point-emission sources of HF and PM10 were identified and assessed. The major finding in the study was that the main source of PM10 and HF was partly open cells in a Søderberg pot room, whereas in a Prebake pot room, the point emissions of the two contaminants were associated with hot bath residues and hot replaced anodes. In order to prevent the simultaneous exposure to HF and PM10 among pot room workers it is important to prevent workers from being close to these point-sources under unfavourable ventilation. Storage of hot residues outside electrolytic cells without any point source ventilation should not occur.