352 results on '"Bocher, Philippe"'
Search Results
2. Alternative Reagent for Revealing the Entire Microstructure of Additive Manufactured Ti–6Al–4V Alloy
3. Heterogeneities induced by uniaxial compression and resulting errors in material behavior assessment
4. Statistical modeling of microstructurally short crack growth in high cycle fatigue
5. An Investigation on Microstructure and Mechanical Properties of a Copper Strip Subjected to Different Routes of Accumulative Roll Bonding Process
6. A new morphology of retained austenite obtained by intercritical tempering of 13Cr-4Ni martensitic stainless steel
7. Size effects on high temperature oxidation of MCrAlY coatings processed via APS and HVOF depositions
8. On the characterization of roughness and geometrical irregularities of additively manufactured single titanium-alloy struts
9. Detecting Defects in Materials Using Deep Convolutional Neural Networks
10. Friction stir processing of austenitic stainless steel cold spray coating deposited on 304L stainless steel substrate: feasibility study
11. Effects of SMAT at cryogenic and room temperatures on the kink band and martensite formations with associated fatigue resistance in a β-metastable titanium alloy
12. Microstructure effects on the machinability behaviour of Ti6Al4V produced by selective laser melting and Electron Beam Melting process
13. Effect of low temperature intercritical heat-treatment on stable crack growth behavior in 13% Cr-4% Ni martensitic stainless steel multipass weldments
14. How does surface integrity of nanostructured surfaces induced by severe plastic deformation influence fatigue behaviors of Al alloys with enhanced precipitation?
15. Monitoring fracture of high-strength steel under tensile and constant loading using acoustic emission analysis
16. Effect of different shot peening conditions on the fatigue life of 300 M steel submitted to high stress amplitudes
17. Macroscopic to nanoscopic in situ investigation on yielding mechanisms in ultrafine grained medium Mn steels: Role of the austenite-ferrite interface
18. On the ductile rupture of 13% Cr-4% Ni martensitic stainless steels
19. Characterization of Subsurface Microstructural Alterations Induced by Hard Turning of Inconel 718
20. Optimization of the edge effect of 4340 steel specimen heated by induction process with flux concentrators using finite element axis-symmetric simulation and experimental validation
21. Analysis of AA2XXX/AA7XXX friction stir welds
22. Oxide dependent wear mechanisms of titanium against a steel counterface: Influence of SMAT nanostructured surface
23. Statistical analysis of high cycle fatigue life and inclusion size distribution in shot peened 300M steel
24. Analytical fatigue life prediction of shot peened AA 7050-T7451
25. Effect of Unidirectional and Cross-Rolling on the Texture Evolution of a Hot Extruded AA6082
26. Texture and Mechanical Properties of Extruded AA6063 Aluminum Alloy
27. Discrete element-periodic cell coupling model and investigations on shot stream expansion, Almen intensities and target materials
28. Effect of tool geometry and welding speed on mechanical properties of dissimilar AA2198–AA2024 FSWed joint
29. Effects of case hardening properties on the contact fatigue of a wind turbine gear pair
30. Reduction of edge effect using response surface methodology and artificial neural network modeling of a spur gear treated by induction with flux concentrators
31. Inconel 718 Superalloy Controlled Surface Integrity for Fatigue Applications Produced by Precision Turning
32. Explicit Runge–Kutta Methods for Stiff Problems with a Gap in Their Eigenvalue Spectrum
33. Finite Element Peen Forming Simulation
34. Finite Element Simulation of Shot Peening: Prediction of Residual Stresses and Surface Roughness
35. A sequential DEM-FEM coupling method for shot peening simulation
36. Effect of inclusions on fracture behavior of cast and wrought 13% Cr-4% Ni martensitic stainless steels
37. Finite element simulation and analysis of serrated chip formation during high–speed machining of AA7075–T651 alloy
38. Macro-defects characterization in cast CA-6NM martensitic stainless steel
39. Ni and Mn enrichment effects on reformed austenite: thermodynamical and low cycle fatigue stability of 13%Cr–4%Ni and 13%Cr–6%Ni stainless steels
40. Effect of Unidirectional and Cross-Rolling on the Texture Evolution of a Hot Extruded AA6082.
41. Texture and Mechanical Properties of Extruded AA6063 Aluminum Alloy.
42. Improving the accuracy of time-harmonic FE simulations in induction heating applications : Towards better ferromagnetic material models
43. Experimental Investigation on High-Cycle Fatigue of Inconel 625 Superalloy Brazed Joints
44. Modeling of cementite coarsening during tempering of low-alloyed-medium carbon steel
45. Investigation into the dissimilar friction stir welding of AA7020-T651 and AA6060-T6
46. Prediction of crack initiation sites in alpha Ti-alloys microstructures under dwell-fatigue using Cellular Automaton simulation method
47. Predicting the effects of material properties gradient and residual stresses on the bending fatigue strength of induction hardened aeronautical gears
48. Microstructure characterization and hardness distribution of 13Cr4Ni multipass weld metal
49. Microstructural and mechanical characterization of a dissimilar friction stir welded butt joint made of AA2024-T3 and AA2198-T3
50. Modeling of materials behavior in finite element analysis and simulation of machining processes
Catalog
Books, media, physical & digital resources
Discovery Service for Jio Institute Digital Library
For full access to our library's resources, please sign in.