Search

Recycling agents (RAs) are added to asphalt binder blends containing recycled materials to mitigate the negative effects of adding oxidized material to asphalt mixtures. Several methods exist to select a particular RA dosage to restore a specific Superpave performance parameter. However, the rheological similarities between the RA-modified systems and typical virgin binders across the complete range of temperatures remain to be ascertained. In this study, two RA dosage selection procedures, one aiming to restore high-temperature performance grade and the other aiming to restore low-temperature performance grade were statistically compared. Quality assurance datasets from Virginia and North Carolina were used to benchmark the typical virgin binder properties, and 17 recycled binder blends using constituent materials from the two states were studied with respect to Superpave binder properties. Both univariate and bivariate statistical analyses were applied to compare and contrast the rheological properties of these blends with the benchmarked virgin binder properties for the two states. Then, a statistical similarity analysis was done using the Mahalanobis distance to evaluate the rheological properties of these blends with those of the reference binders. The study found that both dosage selection procedures were successful in achieving rheological similarity at target-specific temperatures and for specific binder properties but might not necessarily yield similar properties at other temperatures. Finally, an example application is presented using statistical analysis to select an RA dosage that yields a rheological fingerprint more similar to that of virgin binder systems.

The Virginia Department of Transportation currently requires the use of the indirect tensile cracking test (IDT-CT) in accordance with ASTM D8225 in its balanced mix design specifications to evaluate the cracking resistance of several unmodified dense-graded asphalt surface mixtures. Although some studies have been performed, there is still limited information on testing processes that may have effects on the test results. This paper addresses the identification and assessment of factors that could have a significant effect on the cracking tolerance index (CT index) test results based on the IDT-CT when used for mixture quality control and acceptance by an agency, for example, specimen conditioning method, loading rate, and data collection frequency. Test results suggested that device type might be a significant factor for mixtures with relatively low CT index values. IDT-CT results were not dependent on the type of conditioning method (i.e., dry or wet). Further, they were not dependent on the loading rate applied, regardless of the machine type (servo-hydraulic or screw-drive) or the data collection frequency used over a range of 1 to 100 Hz. Sets of four and three test specimen replicates had single-operator and multi-laboratory precision estimates similar to those determined for five-replicate data sets.

Pavement recycling techniques are often perceived as only applicable to lower traffic volume roadways. However, recent studies have shown their potential for long service lives in higher traffic volume applications. This study documented the response of an asphalt pavement section, constructed using full-depth reclamation (FDR) and cold central plant recycling (CCPR), on a portion of I-64 in Virginia reconstructed between 2016 and 2019. The pavement section was instrumented and the response was compared with a similarly instrumented pavement section (Section S12) placed at the National Center for Asphalt Technology (NCAT) Test Track in 2012. Previous studies have shown that Section S12 is a long-life pavement and it carried 30 million equivalent single axle loads (ESALs) while showing no evidence of deterioration at the pavement surface or from installed instrumentation. The results from the I-64 Segment II project showed that it had much lower horizontal strain values at the bottom of the asphalt layers but slightly higher vertical pressure values on top of the subgrade when compared with NCAT Section S12. Despite the slightly higher values (about 1 pounds per square inch [psi] difference), the vertical pressure on top of the subgrade was very low for both pavement sections. The study confirmed that a recycled pavement section could be constructed and result in low strain and pressure values and is expected to have a long service life in a high traffic volume environment.

The Virginia Department of Transportation (DOT) has taken initiatives to implement the Balanced Mix Design (BMD) method to assure the long-term service life of its pavement network from a mixture quality standpoint. As part of this initiative, the cracking tolerance (CT) index obtained from the indirect tensile (IDT) test at intermediate temperature in accordance with ASTM D8225-19 was selected for evaluating the cracking potential of dense-graded surface asphalt mixtures. This prompted the need to generate the precision estimates (repeatability and reproducibility) for the test method for proper implementation during quality measurement practices. Thus, this interlaboratory study was undertaken to determine the precision estimates of the CT index calculated from the IDT test and to develop the associated precision statements. In addition, fracture strain tolerance (FST) and indirect tensile strength were included. Two asphalt mixes with significantly different CT index values were designed for the evaluation. Forty-six pairs of five replicate sets of compacted specimens (one set for each mix) were sent to 41 participating laboratories to be tested at 25°C. The test results were checked for data quality. The effects of loading rate and manufacturers on the indices were also evaluated. The test results indicated that one third of the sets were not tested in full accordance with the ASTM standard, indicating a need for training. The results also indicated that the specified loading rate of 50 ± 2 mm/min in ASTM D8225-19 for the IDT test may need revision. Finally, the precision estimates and associated statements for the three indices were presented.

Asphalt concrete (AC) overlays have been one of the most common treatments used by the Virginia Department of Transportation (VDOT) for maintaining/rehabilitating pavements. However, when the overlay is placed on existing composite pavements or cracked AC pavements, differential movements across any cracks or joints can result in physical tearing of the AC overlay. Thus, the long-term performance of many AC overlays will highly depend on their ability to resist cracking. The purpose of this study was to assess the viability of using high polymer-modified (HP) AC mixtures in Virginia as a crack mitigation technique or when deemed appropriate as a tool for increased resistance to rutting and cracking on higher volume facilities. Another objective was to assess the ability of various testing protocols to discern the performance of pavements through a comprehensive evaluation of three conventional polymer-modified (PMA) and five HP field-produced mixtures placed in Virginia. This included laboratory testing at multiple levels of complexity (basic, intermediate, and advanced) on collected asphalt binders, plant-produced asphalt mixtures, and field cores. The performance characteristics of PMA and HP mixes were evaluated in the laboratory in relation to durability and resistance to rutting and cracking. Based on the mixes tested, stone matrix asphalt (SMA) mixes showed better performance than dense-graded surface mixes (SM) regardless of the asphalt binder type. Moreover, HP mixes showed better performance than PMA mixes regardless of the mixture type. Overall, SMA-HP mixes showed the most promising performance among all evaluated mixes.

The Virginia Department of Transportation (VDOT), like many owner agencies, is interested in ways to facilitate the increased durability of asphalt mixes in an effort to make its roadway network more sustainable, longer lasting, and more economical. The balanced mix design (BMD) method proposes to address this through the incorporation of performance criteria into mix design and acceptance. VDOT has committed to the implementation of the BMD method in an effort to improve asphalt mix performance. The purpose of this study was to continue advancing efforts toward implementation of BMD through the evaluation of 13 asphalt mixes using performance-indicating laboratory tests, validation of the initial performance tests selected for BMD use, and validation of the initial test threshold criteria. Based on the results, the asphalt pavement analyzer (APA) rut test, indirect tensile cracking test (IDT-CT), and Cantabro test were found suitable for continued use in BMD. The current threshold criteria for all three tests were found reasonable based on additional mix testing. The study recommends that APA rut test and IDT-CT results should be compared and correlated to fundamental rutting and cracking tests, respectively, as well as to performance predictions obtained from mechanistic-empirical pavement design simulations, and to field performance for full assurance that test threshold values are appropriate. It was further recommended to evaluate the Cantabro, IDT-CT, and APA rut tests to determine acceptable variability and establish precision statements.

The objective of this paper is to provide information from multiple perspectives on the current state of the practice with regard to using recycled materials and recycling agents (RAs) in asphalt concrete mixtures. This information was collected through a survey of U.S. transportation agencies and RA suppliers combined with a search of RA-related specifications and pilot projects previously constructed. Moreover, a case study describing the Virginia Department of Transportation’s experience with RAs provides a tangible example of how at least one agency is approaching the potential implementation of these technologies. This practice review was achieved by documenting the experience, lessons learned, and best practices of multiple asphalt experienced contractors and asphalt binder suppliers in the Virginia area. This paper follows a similar survey conducted in 2014 as part of NCHRP 09-58 and provides a second look at the use of RAs across North America. Not all state departments of transportation have experience with using RAs. Factors preventing the use of RAs included specification limitations, lack of expertise in processing recycled materials, supporting data, and negative prior experiences. Developing a performance-based testing framework is mandatory for the successful use of RAs. In general, good and frequent communication with the RA supplier is critical and necessary during the planning stages, the production of mixtures, and the continuous quality control by the supplier to resolve issues when they arise. Finally, a strong quality control and quality assurance-testing program should be implemented to ensure that materials meet the properties needed to produce a good-performing mixture.