Search

We report on the anisotropy of the vortex motion surface impedance of a \fst thin film grown on a CaF$_2$ substrate. The dependence on the magnetic field intensity up to 1.2 T and direction, both parallel and perpendicular to the sample $c$-axis, was explored at fixed temperature at two distinct frequencies, $\sim16\;$GHz and $\sim27\;$GHz, by means of bitonal dielectric resonator. The free flux flow resistivity $\rho_{ff}$ was obtained by exploiting standard models for the high frequency dynamics, whereas the angle dependence was studied in the framework of the well known and widely used Blatter-Geshkenbein-Larkin (BGL) scaling theory for anistropic superconductors. Excellent agreement with the scaling law prescription by the fluxon flux flow resistivity was obtained. From the scaling analysis, a low-field mass anisotropy $\sim1.8$ was obtained, well within the value ranges reported in literature. The angular dependence of the pinning constant suggests that pinning is dominated by random, isotropic point pins, consistently with critical current density measurements., Comment: 5 pages, 5 figures, conference ASC2020

We present high frequency measurements of the vortex dynamics of a FeSe$_x$Te$_{1-x}$ ($x=0.5$) thin film grown on a CaF$_2$ substrate and with a critical temperature $T_c\simeq18\;$K, performed by means of a dual frequency dielectric resonator at 16.4 GHz and 26.6 GHz. We extract and discuss various important vortex parameters related to the pinning properties of the sample, such as the characteristic frequency $\nu_c$, the pinning constant $k_p$ and the pinning barrier height $U$ relevant for creep phenomena. We find that the vortex system is in the single-vortex regime, and that pinning attains relatively high values in terms of $k_p$, indicating significant pinning at the high frequencies here studied. The pinning barrier energy $U$ is quite small and exhibits a non-monotonous temperature dependence with a maximum near 12 K. This result is discussed in terms of core pinning of small portion of vortices of size $\propto\xi^3$ jumping out of the pinning wells over very small distances, a process which is favoured in the high frequency, short ranged vortex oscillations here explored., Comment: 18 pages, 7 figures

In this paper we explore the effects of 3.5 MeV proton irradiation on Fe(Se,Te) thin films grown on CaF2. In particular, we carry out a systematic experimental investigation with different irradiation fluences up to 7.30x10^16 cm^-2 and different proton implantation depths, in order to clarify whether and to what extent the critical current is enhanced or suppressed, what are the effects of irradiation on the critical temperature, the resistivity and the critical magnetic fields, and finally what is the role played by the substrate in this context. We find that the effect of irradiation on superconducting properties is generally small as compared to the case of other iron-based superconductors. Such effect is more evident on the critical current density Jc, while it is minor on the transition temperature Tc, on the normal state resistivity and on the upper critical field Hc2 up to the highest fluences explored in this work. In addition, our analysis shows that when protons implant in the substrate far from the superconducting film, the critical current can be enhanced up to 50% of the pristine value at 7 T and 12 K, while there is no appreciable effect on critical temperature and critical fields together with a slight decrease in resistivity. On the contrary, when the implantation layer is closer to the film-substrate interface, both critical current and temperature show a decrease accompanied by an enhancement of the resistivity and the lattice strain. This result evidences that possible modifications induced by irradiation in the substrate may affect the superconducting properties of the film via lattice strain. The robustness of the Fe(Se,Te) system to irradiation induced damage makes it a promising compound for the fabrication of magnets in high-energy accelerators., Comment: 14 pages, 11 figures, submitted to Superconductor Science and Technology

Anisotropy effects on flux pinning and flux flow are strongly effective in cuprate as well as iron-based superconductors due to their intrinsically layered crystallographic structure. However $\textrm{Fe(Se,Te)}$ thin films grown on $\textrm{CaF}_2$ substrate result less anisotropic with respect to all the other iron based superconductors. We present the first study on the angular dependence of the flux flow instability, which occurs in the flux flow regime as a current driven transition to the normal state at the instability point ($I^*$,$V^*$) in the current-voltage characteristics. The voltage jumps are systematically investigated as a function of the temperature, the external magnetic field, and the angle between the field and the $\textrm{Fe(Se,Te)}$ film. The scaling procedure based on the anisotropic Ginzburg-Landau approach is successfully applied to the observed angular dependence of the critical voltage $V^*$. Anyway, we find out that $\textrm{Fe(Se,Te)}$ represents the case study of a layered material characterized by a weak anisotropy of its static superconducting properties, but with an increased anisotropy in its vortex dynamics due to the predominant perpendicular component of the external applied magnetic field. Indeed, $I^*$ shows less sensitivity to angle variations, thus being promising for high field applications.

The stability against quench is one of the main issue to be pursued in a superconducting material which should be able to perform at very high levels of current densities. Here we focus on the connection between the critical current $I_c$ and the quenching current $I^*$ associated to the so-called flux-flow instability phenomenon, which sets in as an abrupt transition from the flux flow state to the normal state. To this purpose, we analyze several current-voltage characteristics of three types of iron-based thin films, acquired at different temperature and applied magnetic field values. For these samples, we discuss the impact of a possible coexistence of intrinsic electronic mechanisms and extrinsic thermal effects on the quenching current dependence upon the applied magnetic field. The differences between the quenching current and the critical current are reported also in the case of predominant intrinsic mechanisms. Carrying out a comparison with high-temperature cuprate superconductors, we suggest which material can be the best trade-off between maximum operating temperature, higher upper critical field and stability under high current bias., Comment: 5 pages, 4 figures

The first step towards high critical currents in Bi-2212 wires was the comprehension that the supercurrent is blocked over long lengths by filament-diameter bubbles grown during the melt stage, which cause expansion of the wire diameter and dedensification of the superconducting filaments. Whereas the previous successful approach to reduce the problem of voids related to bubbles was based on the application of a high overpressure during the heat treatment, we fabricated Bi-2212 wires by applying a new concept of suitably alternating groove-rolling and drawing techniques with the aim of densifying the phase already during the working procedure prior to the heat treatment. We here for the first time were able to reach in wires reacted with closed ends - i.e. with gas trapped in the wire as it happens in long-length wires - the very same values of critical current shown in short wires reacted with open ends. This is the irrefutable evidence that, only by acting on the deformation technique, we were able to raise the critical current by properly densifying the superconducting powder inside the filaments already before the melt stage. Whole-conductor current densities in our long length simulation wires already reach 400 A/mm2 at 4.2 K and 5 T, which can be still easily increased through architecture optimization. The actual breakthrough is that the densification is optimized without further complex treatments through a technique which can be straightforwardly applied to long-lengths wires., Comment: 9 pages, 3 figures

In the present paper we report an in-situ high-energy X-ray diffraction analysis of MgB2 tapes during the preparation process. The experiment was performed in a specifically designed furnace working in reducing atmosphere, compatible with the Laue diffraction condition. The MgB2 synthesis was realized starting from MgH2 and amorphous B in powder form as precursors, varying reaction temperature and testing different cooling processes. We analyzed both the MgB2 synthesis and the sintering process of tapes prepared with these powders. Phase evolution, micro and crystallographic structure were monitored during the different thermal treatments. Among the main results we observed the formation of MgB2 at an extraordinary low temperature (300C), probably as a result of a solid-state reaction between MgH2 and B. Furthermore, we studied the dependence of the micro-structure upon the thermal treatment and its effect on the critical current performance of the superconducting tapes., Comment: 15 pages, 9 figures

Bi2Sr2CaCu2O8+x (Bi-2212) superconducting long-length wires are mainly limited in obtaining high critical currents densities (JC) by the internal gas pressure generated during the heat treatment, which expands the wire diameter and dedensifies the superconducting filaments. Several ways have been developed to increase the density of the superconducting filaments and therefore decreasing the bubble density: much higher critical currents have been reached always acting on the final as-drawn wires. We here try to pursue the same goal of having a denser wire by acting on the deformation technique, through a partial use of the groove-rolling at different wire processing stages. Such technique has a larger powders compaction power, is straightforwardly adaptable to long length samples, and allows the fabrication of samples with round, square or rectangular shape depending on the application requirements. In this paper we demonstrate the capability of this technique to increase the density in Bi-2212 wires which leads to a three-fold increase in Jc with respect to drawn wires, making this approach very promising for fabricating Bi-2212 wires for high magnetic field magnets, i.e. above 25 T.

Recently the interest about Bi-2212 round wire superconductor for high magnetic field use has been enhancing despite the fact that an increase of the critical current is still needed to boost its successful use in such applications. Recent studies have demonstrated that the main obstacle to current flow, especially in long wires, is the residual porosity inside these Powder-In-Tube processed conductors which develops in bubbles-agglomeration when the Bi-2212 melts. Through this work we tried to overcome this issue acting on the wire densification by changing the deformation process. Here we show the effects of groove-rolling versus drawing process on the critical current density JC and on the microstructure. In particular, groove-rolled multifilamentary wires show a JC increased by a factor of about 3 with respect to drawn wires prepared with the same Bi-2212 powder and architecture. We think that this approach in the deformation process is able to produce the required improvements both because the superconducting properties are enhanced and because it makes the fabrication process faster and cheaper.

MgB2 monofilamentary nickel-sheated tapes and wires were fabricated by means of the ex-situ powder-in-tube method using either high-energy ball milled and low temperature synthesized powders. All sample were sintered at 920 C in Ar flow. The milling time and the revolution speed were tuned in order to maximize the critical current density in field (Jc): the maximum Jc value of 6 x 10e4 A/cm2 at 5 K and 4 T was obtained corresponding to the tape prepared with powders milled for 144h at 180rpm. Vorious synthesis temperature were also investigated (730-900 C) finding a best Jc value for the wire prepared with powders synthesized at 745 C. We speculate that this optimal temperature is due to the fluidifying effect of unreacted magnesium content before the sintering process which could better connect the grains.