Search

The laser print, cut, and laminate (PCL) method for microfluidic device fabrication can be leveraged for rapid and inexpensive prototyping of electrophoretic microchips useful for optimizing separation conditions. The rapid prototyping capability allows the evaluation of fluidic architecture, applied fields, reagent concentrations, and sieving matrix, all within the context of using fluorescence-compatible substrates. Cyclic olefin copolymer and toner-coated polyethylene terephthalate (tPeT) were utilized with the PCL technique and bonding methods optimized to improve device durability during electrophoresis. A series of separation channel designs and centrifugation conditions that provided successful loading of sieving polymer in less than 3 min was described. Separation of a 400-base DNA sizing ladder provided calculated base resolution between 3 and 4 bases, a greater than 18-fold improvement over separations on similar substrates. Finally, the accuracy and precision capabilities of these devices were demonstrated by separating and sizing DNA fragments of 147 and 167 bases as 148.62 ± 2 and 166.48 ± 3 bases, respectively.

Entamoeba histolytica is a pathogenic protozoan parasite that causes intestinal colitis, diarrhea, and in some cases, liver abscess. Through transcriptomics analysis, we observed that E. histolytica infection was associated with increased expression of IL-33 mRNA in both the human and murine colon. IL-33, the IL-1 family cytokine, is released after cell injury to alert the immune system of tissue damage. Treatment with recombinant IL-33 protected mice from amebic infection and intestinal tissue damage; moreover, blocking IL-33 signaling made mice more susceptible to amebiasis. IL-33 limited the recruitment of inflammatory immune cells and decreased the pro-inflammatory cytokine IL-6 in the cecum. Type 2 immune responses were upregulated by IL-33 treatment during amebic infection. Interestingly, administration of IL-33 protected RAG2-/- mice but not RAG2-/-γc-/- mice, demonstrating that IL-33-mediated protection required the presence of innate lymphoid cells (ILCs). IL-33 induced recruitment of ILC2 but not ILC1 and ILC3 in RAG2-/- mice. At baseline and after amebic infection, there was a significantly higher IL13+ILC2s in C57BL/J mice, which are naturally resistant to amebiasis, than CBA/J mice. Adoptive transfer of ILC2s to RAG2-/-γc-/- mice restored IL-33-mediated protection. These data reveal that the IL-33-ILC2 pathway is an important host defense mechanism against amebic colitis.

Entamoeba histolytica is a pathogenic protozoan parasite that causes intestinal colitis, diarrhea, and in some cases, liver abscess. Through transcriptomics analysis, we observed that E. histolytica infection was associated with increased expression of IL-33 mRNA in both the human and murine colon. IL-33, the IL-1 family cytokine, is released after cell injury to alert the immune system of tissue damage during infection. Treatment with recombinant IL-33 protected mice from amebic infection and colonic tissue damage; moreover, blocking IL-33 signaling made mice more susceptible to infection and weight loss. IL-33 limited the recruitment of inflammatory immune cells and decreased the pro-inflammatory cytokine IL-6 in the colon. Type 2 immune responses, which are known to be involved in tissue repair, were upregulated by IL-33 treatment during amebic infection. Interestingly, administration of IL-33 protected RAG2-/- mice but not RAG2-/-γc-/- mice, demonstrating that IL-33 mediated protection occurred in the absence of T or B cells but required the presence of innate lymphoid cells (ILCs). IL-33 induced recruitment of ILC2 but not ILC1 and ILC3 in RAG2-/- mice. Adoptive transfer of ILC2s to RAG2-/-γc-/- mice restored IL-33 mediated protection. These data reveal that the IL-33-ILC2 pathway is an important host defense mechanism against amebic colitis.

Forensic DNA analysis requires several steps, including DNA extraction, PCR amplification, and separation of PCR fragments. Intuitively, there are numerous situations where it would be beneficial to speed up the overall DNA analysis process; in this work, we focus on the most time-consuming component in the analysis pipeline, namely the polymerase chain reaction (PCR). Primers were specially designed to target 10 human genomic loci, all yielding amplicons shorter than 350 bases, for ease of downstream integration with on-board microchip electrophoresis. Primer concentrations were adjusted specifically for microdevice amplification, resulting in well-balanced short tandem repeat (STR) profiles. Furthermore, studies were performed to push the limits of the DNA polymerase to achieve rapid, multiplexed PCR on various substrates, including transparent and black polyethylene terephthalate (Pe), and with two distinct adhesives, toner and heat sensitive adhesive (HSA). Rapid STR-based multiplexed PCR amplification is demonstrated in 15 min on a Pe microdevice using a custom-built system for fluid flow control and thermocycling for the full 10-plex, and in 10 min for a smaller multiplex consisting of six core CODIS loci plus Amelogenin with amplicons shorter than 200bp. Lastly, preliminary studies indicate the capability of this PCR microdevice platform to be integrated with both upstream DNA extraction, and downstream microchip electrophoresis. This, coupled to the use of reagents that are compatible with lyophilization (lyo-compatible) for PCR, represents the potential for a fully integrated rotationally-driven microdevice for complete forensic DNA analysis.

Total bilirubin (T-Bil) is an important clinical diagnostic marker that is measured frequently by physicians to assist in the diagnosis, treatment, and monitoring of multiple medical conditions. The work demonstrated here utilizes the 48-year-old mechanism of phototherapy that is commonly implemented in the treatment of infants with exaggerated physiologic and pathologic jaundice but adapts it to the microfluidic level for the ultimate purpose of total bilirubin quantitation. After acquisition of a small volume of blood (

Polymeric biguanides, as well as quaternary ammonium compounds, are ubiquitous antimicrobial agents in healthcare. Due to the highly cationic and polymeric nature of these compounds and the complex matrices in which they are found, the analytical characterization of products containing them remains challenging. In this work an efficient, sensitive, and high-resolution separation protocol was developed to perform quantitative measurements (sub-mg L −1 ) of alexidine dihydrochloride (ADH) and polyhexamethylene biguanide (PHMB) in commercial multipurpose contact lens solutions (MPS). Initially, contactless conductivity (C 4 D) detection was explored, but lacked adequate selectivity and sensitivity to quantify PHMB or ADH in commercial MPS. To overcome these limitations, an alternative approach using solid phase extraction (SPE) followed by separation with reversed phase ultra-performance liquid chromatography (RP-UPLC) was developed for both ADH and PHMB separation and detection. The most sensitive and reliable method investigated utilized standard additions to compensate for matrix effects. For ADH, concentration values measured with the presented method were consistent with data provided by the MPS manufacturer (1.6 mg L −1 ) within 0.10 mg L −1 . PHMB quantification in MPS products was successful at concentrations −1 with quantitative reproducibility better than 2% RSD. Comparison of blind sample testing using the RP-UPLC method showed strong correlation (R 2 = 0.939) of PHMB concentrations with results obtained by the United States Food and Drug Administration using a published HPLC-Evaporative light scattering detection (ELSD) assay. A significant advantage of this method is the ability to partially resolve PHMB polydispersity, which to date has been minimally studied and explained. By coupling with electrospray mass spectrometry (MS), a general trend was observed for increased retention as a function of PHMB chain length. The improved robustness and reproducibility of UV detection versus ELSD coupled with the superior resolving power of UPLC is an asset to the detection and characterization of PHMB and ADH. In addition to quality control of MPS, this method has potential application to the analyses skin wipes, wound dressings and other medical products where understanding how manufacturing processes lead to differences in polydispersity is important to maximize the antimicrobial properties while minimizing toxicologic effects.

We demonstrate the capabilities of a centrifugal polyethylene terephthalate toner (PeT) microdevice for integrated on-chip reagent mobilization, mixing, and PCR amplification for genetic analysis of short tandem repeats (STR). Fluid flow, including reagent mobilization and mixing, is achieved by centrifugal force, eliminating the need for bulky instrumentation. The use of a passive valve also eliminates the need for extra hardware and simplifies the chip and the device design. A custom-built system is capable of thermocycling through a dual Peltier clamping system, as well as variable rate spinning with a DC motor. A multiplex PCR amplification of alleles associated with 18 genomic loci was successfully performed on-chip, followed by capillary electrophoretic separation, which showed efficient amplification of DNA from multiple sources. The genetic profiles generated were 100% concordant with those obtained using conventional PCR methods. The resultant system represents a novel microfluidic PCR amplification platform that uses inexpensive PCR microdevices that are simple to fabricate, yet effective for complex, multiplexed PCR.

To date, the forensic community regards solid phase extraction (SPE) as the most effective methodology for the purification of DNA for use in short tandem repeat (STR) polymerase chain reaction (PCR) amplification. While a dominant methodology, SPE protocols generally necessitate the use of PCR inhibitors (guanidine, IPA) and, in addition, can demand timescales of up to 30 min due to the necessary load, wash and elution steps. The recent discovery and characterization of the EA1 protease has allowed the user to enzymatically extract (not purify) DNA, dramatically simplifying the task of producing a PCR-ready template. Despite this, this procedure has yet to make a significant impact on microfluidic technologies. Here, we describe a microfluidic device that implements the EA1 enzyme for DNA extraction by incorporating it into a hybrid microdevice comprising laminated polyester (Pe) and PMMA layers. The PMMA layer provides a macro-to-micro interface for introducing the biological sample into the microfluidic architecture, whilst also possessing the necessary dimensions to function as the swab acceptor. Pre-loaded reagents are then introduced to the swab chamber centrifugally, initiating DNA extraction at 75 °C. The extraction of DNA occurs in timescales of less than 3 min and any external hardware associated with the transportation of reagents by pneumatic pumping is eliminated. Finally, multiplexing is demonstrated with a circular device containing eight separate chambers for the simultaneous processing of eight buccal swab samples. The studies here provide DNA concentrations up to 10 ng μL(-1) with a 100% success rate in less than 3 minutes. The STR profiles generated using these extracted samples demonstrate that the DNA is of PCR forensic-quality and adequate for human identification.

The use of overhead transparencies as substrates for the fabrication of microfluidic devices brings new capabilities in the creation of fully-integrated systems. Here, we describe a reagent storage method through inkjet printing that is complementary to the simple print, cut and laminate (PCL) fabrication technique, which already incorporates printing toner onto commercial off-the-shelf materials for fabrication of polyester–toner microdevices. With the surface of the polyester film dramatically different than paper, substrate optimization was required to increase printability without incorporating additional substrate-coating steps. Functionality for chemical sensing devices, operated centrifugally here, was demonstrated through standard human serum albumin analysis. Quantitative results were obtained through image analysis using a desktop scanner to determine color change in the presence of various total protein and albumin concentrations. Printed devices exhibited a shelf life of at least two months with no loss in activity, resulting in a relative standard deviation of 0.652% for total protein analysis.

In the last decade, the microfluidic community has witnessed an evolution in fabrication methodologies that deviate from using conventional glass and polymer-based materials. A leading example within this group is the print, cut and laminate (PCL) approach, which entails the laser cutting of microfluidic architecture into ink toner-laden polyester sheets, followed by the lamination of these layers for device assembly. Recent success when applying this method to human genetic fingerprinting has highlighted that it is now ripe for the refinements necessary to render it amenable to mass-manufacture. In this communication, we detail those modifications by identifying and implementing a suitable heat-sensitive adhesive (HSA) material to equip the devices with the durability and resilience required for commercialization and fieldwork. Importantly, this augmentation is achieved without sacrificing any of the characteristics which make the PCL approach attractive for prototyping. Exemplary HSA-devices performed DNA extraction, amplification and separation which, when combined, constitute the complete sequence necessary for human profiling and other DNA-based analyses.

Current conventional methods utilized for forensic DNA analysis are time consuming and labor-intensive requiring large and expensive equipment and instrumentation. While more portable Rapid DNA systems have been developed, introducing them to a working laboratory still necessitates a high cost of initiation followed by the recurrent cost of the devices. This has highlighted the need for an inexpensive, rapid and portable DNA analysis tool for human identification in a forensic setting. In order for an integrated DNA analysis system such as this to be realized, device operations must always be concluded by a rapid separation of short-tandem repeat (STR) DNA fragments. Contributing to this, we report the development of a unique, multi-level, centrifugal microdevice that can perform both reagent loading and DNA separation. The fabrication protocol was inspired by the print, cut and laminate (PCL) technique described previously by our group, and in accordance, offers a rapid and inexpensive option compared with existing approaches. The device comprises multiple polyester-toner fluidic layers, a cyclic olefin copolymer separation domain and integrated gold leaf electrodes. All materials are commercially-available and complement the PCL process in a way that permits fabrication of increasingly sought after single-use devices. All reagents, including a viscous sieving matrix, are loaded centrifugally, eliminating external pneumatic pumping, and the sample is separated in

Hematocrit (HCT) measurements are important clinical diagnostic variables that help physicians diagnose and treat various medical conditions, ailments, and diseases. In this work, we present the HCT Disc, a centrifugal microdevice fabricated by a Print, Cut and Laminate (PCL) method to generate a 12-sample HCT device from materials costing

We describe a technique for fabricating microfluidic devices with complex multilayer architectures using a laser printer, a CO2 laser cutter, an office laminator and common overhead transparencies as a printable substrate via a laser print, cut and laminate (PCL) methodology. The printer toner serves three functions: (i) it defines the microfluidic architecture, which is printed on the overhead transparencies; (ii) it acts as the adhesive agent for the bonding of multiple transparency layers; and (iii) it provides, in its unmodified state, printable, hydrophobic 'valves' for fluidic flow control. By using common graphics software, e.g., CorelDRAW or AutoCAD, the protocol produces microfluidic devices with a design-to-device time of ∼40 min. Devices of any shape can be generated for an array of multistep assays, with colorimetric detection of molecular species ranging from small molecules to proteins. Channels with varying depths can be formed using multiple transparency layers in which a CO2 laser is used to remove the polyester from the channel sections of the internal layers. The simplicity of the protocol, availability of the equipment and substrate and cost-effective nature of the process make microfluidic devices available to those who might benefit most from expedited, microscale chemistry.