Search

This paper conducts a validation of two linearization approaches that utilize baseband nonlinear linearization signals of the 2nd order, through practical experiments on an asymmetrical two-way microstrip Doherty amplifier (ADA), and simulations on a symmetrical two-way Doherty amplifier (DA) as well as the single stage power amplifier (PA) for the post-OFDM 5G modulation formats. In the first approach, linearization signals are led at the input and output of the carrier transistor in the DA, while in the second approach, they are injected at the outputs of both the carrier and peaking amplifiers. The DA was tested in simulation for the FBMC signal of 20 MHz bandwidth, while the experimental measurements were performed for the FBMC signal on the ADA for different useful signal frequency bandwidths, 5 MHz, 7.5 MHz, and 10 MHz. The maximal improvement of DA linearity obtained in simulation is 10 dB for lower power and 5 dB for maximum amplifier output power, while the second approach gives around 2 dB better results for higher power levels. The experimental test for ADA performed for considered signal bandwidths indicates 3 dB to 5 dB linearity improvement for the implemented approaches and more symmetrical results achieved by the second approach. Additionally, the simulation tests for the PA were carried out for the FBMC, UFMC, and FOFDM signals of 100 MHz bandwidth, with the application of the first linearization approach. The minimal achieved linearization improvement is 13 dB for the FOFDM signal and a maximal of 18 dB for the FBMC signal. [ABSTRACT FROM AUTHOR]

Introduction/purpose: This paper presents initial development of the procedure for electric field estimation in the vicinity of 5G base stations. Methods: The procedure allows determination of future radiation levels before traffic is established over applied antenna systems on the basis of measured values of electric field levels caused by the signal forming Synchronization Signal Block. It is possible to perform necessary calculations for a very accurate estimation even if some important parameters of the radiation characteristics (such as the frequency span between the frequency carriers on the radio interface) are not a priori known. In this way, communication with mobile system operators before measurement is significantly simplified because operators do not need to know system technical details. Results: The developed formula for electric field estimation is verified comparing the calculated values by its implementation to the practical results obtained by intensive measurements on a great number of 5G base stations in a highly developed country. The formula gives a pessimistic result, i.e. a higher electric field level than it is obtained by all such performed measurements. Conclusion: This estimation allows mobile system operators to predict whether the electromagnetic field around base stations could be dangerous for human health when systems come to full operation while considering national and international recommendations dealing with radiation levels. [ABSTRACT FROM AUTHOR]

Copyright of Informacije MIDEM: Journal of Microelectronics, Electronic Components & Materials is the property of MIDEM Society and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

This paper presents an optimization-based approach to the design of asymmetrical filter structures having the maximum number of return--or insertion-loss ripples in the passband such as those based upon Chebyshev function prototypes. The proposed approach has the following advantages over the general purpose optimization techniques adopted previously such as: less frequency sampling is required, optimization is carried out with respect to the Chebyshev (or minimax) criterion, the problem of local minima does not arise, and optimization is usually only required for the passband. When implemented around an accurate circuit simulation, the method can be used to include all the effects of discontinuities, junctions, fringing, etc. to reduce the amount of tuning required in the final filter. The design of asymmetrical ridged-waveguide bandpass filters is considered as an example. Measurements on a fabricated filter confirm the accuracy of the design procedure. Index Terms--Bandpass filters, computer optimization, rectangular waveguide, ridged waveguide, waveguide filters.

A computer-aided synthesis technique for E-plane bandpass filters with improved stopband performance is developed. An optimization procedure based on equal ripple optimization is adopted. The design of a symmetrical E-plane bandpass filter with improved stopband performance is considered; higher order mode interaction between E-plane discontinuities is included in the design. The predicted filter performance shows improved stopband performance and reduced filter dimensions compared with conventional E-plane bandpass filters. The validity of the method is confirmed by the measurement of a fabricated five resonator E-plane bandpass filter with improved stopband performance.

In this paper, a miniaturized microstrip quadrature hybrid coupler (QHC) using U‐shaped transmission lines (USTLs) is presented. The proposed approach replaces all arms of the conventional QHC with its equivalent USTL to achieve compactness. The proposed coupler structure is designed to operate in the 1.5 GHz (1427‐1518 [MHz]) band which is one of the 5G bands of interest. At such low RF/microwave bands below 3‐4 GHz, the size of the conventional coupler is considerably very large which raises a concern for the next generation networks. The proposed coupler is designed, simulated and fabricated using Rogers 5880 with thickness of 0.79 mm, dielectric constant (εr) of 2.2 and loss tangent of 0.0021. The proposed QHC size is 70% smaller in circuit area (30% relative area) than the conventional equivalent. Simulation and measured results are presented and good matching between the results is observed, confirming the outstanding coupler performance properties. The proposed miniaturized QHC structure will play a vital role for next generation 4G and 5G wireless communication systems operating below 6 GHz. [ABSTRACT FROM AUTHOR]