Search

Abstract One of the most important parts of direct evaporative cooling systems is the cooling pad. Pads vary in materials and construction features. The parameters studied in the performance of the pads are air speed, pad thickness, geometrical characteristics, and its configuration and the provided water flow rate. The performance of the pads is usually determined through saturation efficiency, pressure drop, temperature drop and humidity increase in the treated air, evaporation and water consumption, cooling capacity, coefficient of performance, and heat and mass transfer coefficients. Since the geometry and how to place the pad in the evaporative cooling system is one of the most important issues related to the performance of such systems, the present work experimentally investigates the amount of cooling and evaporation of the direct evaporative cooling system under 5 different angles of placement of the cellulose pad in relation to the vertical position. It includes angles of $$0^\circ$$ 0 ∘ , $$5^\circ$$ 5 ∘ , $$10^\circ$$ 10 ∘ , $$15^\circ$$ 15 ∘ , and $$20^\circ$$ 20 ∘ in 5 different air speeds, 2 different inlet water flow rates, 2 inlet air temperatures, and 2 different inlet water temperatures. Results show that the lowest output temperature, highest air relative humidity, highest coefficient of performance (about 12% more than $$0^\circ$$ 0 ∘ ), highest saturation efficiency, and highest evaporation rate are obtained in the case of a $$15^\circ$$ 15 ∘ of cooling pad placement angle.

One of the most important parts of direct evaporative cooling systems is the cooling pad. Pads vary in materials and construction features. The parameters studied in the performance of the pads are air speed, pad thickness, geometrical characteristics, and its configuration and the provided water flow rate. The performance of the pads is usually determined through saturation efficiency, pressure drop, temperature drop and humidity increase in the treated air, evaporation and water consumption, cooling capacity, coefficient of performance, and heat and mass transfer coefficients. Since the geometry and how to place the pad in the evaporative cooling system is one of the most important issues related to the performance of such systems, the present work experimentally investigates the amount of cooling and evaporation of the direct evaporative cooling system under 5 different angles of placement of the cellulose pad in relation to the vertical position. It includes angles of 0 ∘ , 5 ∘ , 10 ∘ , 15 ∘ , and 20 ∘ in 5 different air speeds, 2 different inlet water flow rates, 2 inlet air temperatures, and 2 different inlet water temperatures. Results show that the lowest output temperature, highest air relative humidity, highest coefficient of performance (about 12% more than 0 ∘ ), highest saturation efficiency, and highest evaporation rate are obtained in the case of a 15 ∘ of cooling pad placement angle. [ABSTRACT FROM AUTHOR]

The effectiveness of using wetted cellulose pads on improving the performance of two conventional passive cooling systems has been evaluated. First, an experimental design was developed to determine the impact of using a wetted cellulose pad on the temperature and velocity of the airflow. A cellulose pad (7090 model) with a cross-sectional area of 0.5 × 0.5 m2 and three different thicknesses of 10, 15, and 30 cm were selected and tested. The results indicated that using wetted cellulose pads with thicknesses ranging from 10–30 cm decreased the outlet airflow temperature from 11.3 to 13.7 °C on average. For free airflow at velocity 3.5 m/s, the outlet airflow velocity from the wetted cellulose pad decreased to 0.9, 0.7 and 0.6 m/s, respectively, for cellulose pads with thicknesses of 10, 15, and 30 cm. By applying experimental results on a psychrometric chart, the humidity ratio of outlet airflow was obtained between 40–70%. The study established airflow velocity as the critical parameter in passive cooling systems. With the novel concept of combining wetted cellulose pads for passive cooling systems (i.e., wind catchers and induced ventilation), there is good potential to reduce the energy requirements for thermal comfort in buildings in regions with a hot and arid climate.

It has been found a linear progression between the panel temperature and its efficiency. A novel cellulose pad arrangement, which is saturated with water, at back surface of photovoltaic panel for cooling has achieved better results. The experimental results showed a reduction in maximum PV panel temperature at using the proposed water cooling system. The average temperature of the PV panel dropped 10.1°C and an increase in average solar panel efficiency about 20.8% during operating time. Then, a comparison between the PV panel results cooling by natural convection and using the proposed water cooling system will reveal the most efficient.

The effectiveness of using wetted cellulose pads on improving the performance of two conventional passive cooling systems has been evaluated. First, an experimental design was developed to determine the impact of using a wetted cellulose pad on the temperature and velocity of the airflow. A cellulose pad (7090 model) with a cross-sectional area of 0.5 × 0.5 m2 and three different thicknesses of 10, 15, and 30 cm were selected and tested. The results indicated that using wetted cellulose pads with thicknesses ranging from 10–30 cm decreased the outlet airflow temperature from 11.3 to 13.7 °C on average. For free airflow at velocity 3.5 m/s, the outlet airflow velocity from the wetted cellulose pad decreased to 0.9, 0.7 and 0.6 m/s, respectively, for cellulose pads with thicknesses of 10, 15, and 30 cm. By applying experimental results on a psychrometric chart, the humidity ratio of outlet airflow was obtained between 40–70%. The study established airflow velocity as the critical parameter in passive cooling systems. With the novel concept of combining wetted cellulose pads for passive cooling systems (i.e., wind catchers and induced ventilation), there is good potential to reduce the energy requirements for thermal comfort in buildings in regions with a hot and arid climate. [ABSTRACT FROM AUTHOR]