Search

A dc voltage restorer (dc‐VR) with optimal droop control is developed to reduce the power loss and solve the dynamic current imbalance simultaneously of the zonal dc distribution system integrating multi‐parallel energy storage. Firstly, the power loss model composed of line loss and converter loss is built and it is proved to be a strictly convex function with respect to droop coefficients, which indicates the power loss can be mitigated by optimizing the current distribution. Thus, an image‐based droop optimization method is proposed to search for the optimal droop coefficients. Then, the economy of voltage compensation on power loss reduction is investigated and an ESS‐combined dc‐VR is designed, including an interleaved parallel architecture and a capacitor‐integrated electric spring (C‐ES). Unified virtual inertia is proposed for interleaved parallel bridge arms to make their dynamic performance consistent. And the newly introduced C‐ES can keep the bus voltage at the rated level to reduce the system cost. Therefore, the problem of dynamic currents imbalance is addressed from the points of converter structure (dc‐VR) and control system (unified inertia), and the power loss can be reduced by voltage recovery (C‐ES) and optimizing the current reallocation which is achieved by updating sharing coefficients from the image‐based droop optimization method. Finally, the simulation cases validate the effectiveness of the proposed optimal‐droop dc‐VR on dynamic current balance and power loss reduction, and hardware in the loop experiment results prove the consistent dynamic characteristics of the dc‐VR's arms. [ABSTRACT FROM AUTHOR]

The bidirectional DC‐DC conversion, as an important application scenario, places certain requirements on the topology structure. The four‐switch buck‐boost (FSBB) converter has received widespread attention due to its simple structure, flexible control and state switchability. However, the traditional control strategy makes it difficult to meet the requirements of high performance, high stability and high security at the same time. Furthermore, the control methods commonly adopted in domestic and international practical applications rely heavily on analogue control, which cannot maintain efficiency over a wide stability range. The use of digital control methods allows for optimized control algorithms, maintaining stable system operation and improving efficiency. Therefore, it is very important to use the digital control method to further improve the smoothness and steady‐state efficiency of the system multi‐mode switching while maintaining a wide input and output range, based on this, this study proposes two new three‐mode control modes: interleaved bias control mode and dual‐edge bias control mode. [ABSTRACT FROM AUTHOR]

Dual active bridge (DAB) is an isolated DC‐DC converter gaining wider attention in power electronics applications. The high frequency (HF) transformer is an integral part of the DAB which is prone to saturation. Silicon carbide (SiC) based DAB are generally preferred for highly efficient power conversions, calling for an extremely low DC resistance of the transformer. This aggravates the DC bias issue significantly. The DC bias current generally flows due to the mismatch in static and transient switching of active devices, leading to eventual saturation of the transformer. This paper proposes an active method to precisely control the dead time of the devices (8–100 ns) without sacrificing the voltage utilization of the converter. This method does not require a sophisticated DC offset current measurement technique. The field programmable gate array (FPGA) based control platform on the gate driver side executes the proposed algorithm. The proposed control is experimentally verified in a 5 kW SiC based converter. The control implementation methodology is discussed with the support of necessary experimental results. [ABSTRACT FROM AUTHOR]

The modular multilevel DC–DC transformer (MMDCT) provides a reliable solution to overcome the challenges of conventional dual‐active‐bridge converters in terms of power semiconductors ratings and dv/dt stress on transformer coupling windings. An alternative modulation method, quasi‐square‐wave, was proposed to reduce the cell capacitance of modular multilevel bridges. However the application of quasi‐square‐wave modulation is found to result in underdamped switching transients and losses when resetting energy stored in arm inductance. This paper presents a detailed transient analysis of MMDCT arm insertion based on an equivalent circuit, which contributes to a more accurate component sizing and gives voltage estimation for individual half‐bridge submodules. Additionally, a revised switching sequence is proposed to recover this inductor energy and lower the oscillation‐related losses. Simulated and experimental results from a scaled test rig of MMDCT are implemented and validate the proposed component sizing and switching sequence, indicating that the converter efficiency can be improved under revised switching sequence. Finally, a silicon carbide based, high‐frequency MMDCT is proposed and simulated. [ABSTRACT FROM AUTHOR]

The linear power amplifier (LPA) suffers from low power supply utilization in the DC power supply mode, leading to reduced output efficiency. This paper constructs an efficient power supply mode based on closed‐loop dynamic power supply system (CLDPSs). The CLDPSs can generate a pair of bipolar dynamic power supplies based on a predetermined signal to provide power to LPA, which can maintain a small voltage drop between the power supply and the output of LPA, thereby improving the power supply utilization of LPA. In addition, the study also focuses on the conflicting relationship between the output ripple and the dynamic performance of the CLDPSs, for which a new parametric design of the LC filter circuit is proposed, aiming to achieve a balance between these two aspects. Finally, a voice coil motor driving platform is constructed for experimental testing. The results demonstrate that the output ripple and dynamic performance of the CLDPSs can be balanced. In comparison to the DC power supply mode, the CLDPSs power supply mode can enhance the efficiency of LPA by 2 times while the driving accuracy of voice coil motor is basically unchanged. [ABSTRACT FROM AUTHOR]

This paper proposes a new control method for loss reduction of two series buck converters. The proposed method can be applied to each series of buck converters with two power switches. To enhance the efficiency of the converter compared to other structures, a method based on determining operating cycles for loss reduction is employed, leading to increased output efficiency of the converter. Additionally, to demonstrate the efficiency improvement using the proposed method compared to the conventional approach, the efficiency of converter is calculated through theoretical computations under real conditions, and the output results are compared for both losses and efficiency. In addition, the proposed high‐buck converter in this paper benefits from a common ground advantage and exhibits a suitable conversion ratio. The high‐buck converters are used in numerous applications for situations with low voltage and low power. The most important applications for these converters are the power supply for mobile phones, tablets, and other portable electronic devices, battery chargers, and LED drivers. Here, in order to demonstrate the validity of the proposed method, the MATLAB‐Simulink results are provided. Moreover, in order to show the feasibility of the high‐buck converter, a 100‐W prototype has been implemented and the experimental results are provided. [ABSTRACT FROM AUTHOR]

This paper investigates and technically demonstrates a capacitive power transfer (CPT) system applicable to the charging of emerging very‐low‐power portable devices. The constant‐current operation of the primary LCL compensation in CPT is implemented and analysed to simplify the system design process and minimize the configuration on the receiving side. Additionally, the system design considerations for the capacitive coupler and the diode rectifier are presented based on the battery charging specifications. All the design concepts and considerations are validated through experimentation with a 13.56 MHz CPT system, which achieves load‐independent constant‐current output from full‐load to light‐load (one‐tenth of the full load) charging operations. [ABSTRACT FROM AUTHOR]

Modern power system networks are under statutory obligations to integrate renewable energy sources (RES). The primary reason is to meet ever‐increasing energy demand and also to curtail environmental pollution by greenhouse gases. However, the higher penetration of RES has the tendency of reducing inertia of overall power system network. Consequently, frequency stability is affected and deviates beyond allowable permissible limits leading to power blackouts, load shedding, and even total system failure. To address the issues associated with reduced inertia, an optimal control of hybrid energy storage system (HESS) has been proposed. HESS is basically a combination of battery and ultracapacitor, where ultracapacitor addresses rapidly varying power component by mimicking inertia while the battery compensates long‐term power variations. Thus, the HESS is effectively controlled to compensate the loss of inertia by regulating its energy flow. For the purpose of improved efficiency and better power management of the HESS, an improvised particle swarm optimization (MPSO)‐based virtual inertia control design has been proposed. The proposed MPSO is utilized to tune the gains of bidirectional dc–dc converter in such a way that improves frequency nadir with faster response to transient disturbances. This proposed method is simulated in MATLAB and its merits are validated in real time using hardware in loop. On analysing of the results, it can be observed that frequency nadir is improved by 48.96% with significant reduction in rate of change of frequency in comparison to conventional particle swarm optimization. [ABSTRACT FROM AUTHOR]

A soft switching non‐isolated bidirectional DC–DC converter with an improved voltage conversion ratio without any additional auxiliary switch is presented in this paper. In the proposed converter, improved step‐up/step‐down gain conversion is achieved by employing the coupled inductors method. Also, the auxiliary circuit provides soft switching conditions for all the semiconductor elements, regardless of the power flow direction and without any extra voltage stress. The other switch helps provide soft switching conditions for the main switch. Moreover, the switch used for providing soft switching conditions operates as a synchronous rectifier as well. The additional circuit added to attain soft switching is composed of an inductor, coupled with the converter's main inductor, and two auxiliary diodes. The auxiliary diodes benefit from zero‐current‐switching conditions. Fully soft switching conditions for all semiconductor devices, removing the reverse recovery problem, and a low number of components have led to mitigating switching losses and improving efficiency. Detailed operating principles and a theoretical analysis of the proposed converter are presented. Also, the experimental results of a 220 W prototype circuit are provided to confirm the validity of the proposed topology. [ABSTRACT FROM AUTHOR]

For cooperation among distributed generations in a DC microgrid (MG), distributed control is widely applied. However, the delay in distributed communication will result in steady‐state bias and the risk of instability. This paper proposes a novel distributed control for time‐delayed DC MGs to achieve accurate current proportional sharing and weighted average voltage regulation. Firstly, by utilizing an advanced observer based on the PI consensus algorithm, the steady‐state bias problem is addressed. Then, using the passivity theory, stability analysis is conducted to reveal the principle of system instability caused by communication delay. On this basis, to offset the adverse effects of communication delay on the system stability, scattering transformation is introduced in the observer‐based distributed control. Moreover, considering the potential delay from the measurement stage in real‐life scenarios, the sufficient condition of the system stability is concluded by constructing the Lyapunov–Krasovskii functional. Finally, the performance of the proposed control and conclusions of stability analysis are verified by hardware‐in‐loop tests. [ABSTRACT FROM AUTHOR]

The DC–DC conversion stage of a three‐stage solid‐state transformer is the most challenging due to the combination of high power, medium voltage, and medium frequency. This combination also causes most of the losses in the DC–DC stage. To address this issue, a new asymmetrical quadruple active bridge series resonant DC–DC converter (AQAB‐SRC) has been proposed as a building block for solid‐state transformers. The converter achieves soft switching of all switches throughout the operating range by extending and using the half‐cycle continuous conduction mode control strategy. It also has fewer high‐frequency transformers compared to other converters, as more bridges are connected to the same multi‐winding transformer. The optimal design of AQAB‐SRC has been analyzed theoretically, and simulation and lab‐scale experimental results have been obtained to validate the feasibility and validity of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper presents a non‐isolated DC‐DC converter designed to validate ultra‐high voltage gain using a modified double boost mode. The objective is to achieve exceptionally high voltage gain by integrating a modified triple boost technique (MTBT), interleaved with second main and auxiliary third MOSFETs, and a modified switched inductor‐capacitor (MSLC), effectively doubling the voltage transfer gain. Furthermore, MSLC is combined with the auxiliary third and double main MOSFET to double the voltage gain while concurrently mitigating voltage stress on the auxiliary MOSFET and diodes in the proposed converter (the PC). Additionally, all diodes in the MTBT operate under zero current switching (ZCS) and the double main and auxiliary third MOSFET face very low current stress at ultra‐high voltage gain. The input current of the PC remains steady without pulsating at a low duty ratio, making the PC more suitable for renewable energy systems. The PC offers numerous advantages, exhibiting high efficiency and ensuring minimal voltage stress on power devices with low current stress on the power switches. Notably, PC aims to elevate input voltages from 30 V to a variable output range of 335 to 600 V, delivering 440 watts at 96.1% efficiency. [ABSTRACT FROM AUTHOR]

This article presents the new hybrid switched‐capacitor (SC)‐based transformerless DC–DC converter with a high step‐up capability and common ground features. The proposed hybrid SC‐based converter provides low voltage stress across semiconductor devices to utilize MOSFETs with lower Rdson and low voltage ratings. In addition, the diodes in SC cells with low voltage stress can reduce the reverse recovery power loss of the converter. Thus, the overall efficiency of the proposed hybrid SC‐based converter can be increased. The converter circuit, operating principle, and design guidelines of the proposed hybrid SC‐based converter are discussed. To confirm the performance of the proposed hybrid SC‐based converter, a detailed comparison study with the conventional hybrid SC converter is also presented. Finally, a laboratory prototype with 200 W and 25 to 200 V is set up to verify the effectiveness of the proposed hybrid SC‐based converter. [ABSTRACT FROM AUTHOR]

A data‐driven Buck converter model identification method is proposed to deal with missing (incomplete) outputs, which is robust to the data length and percentage of missing data. A nuclear norm based convex optimization problem instead of linear interpolation, to guarantee the recovered missing data satisfying the potential model structured low‐rank character, is constructed to estimate missing outputs. The alternating direction method of multiplier strategy is used to solve the nuclear norm based convex optimization problem. In this way, the high‐quality missing data can be estimated, even for short data length and high percentage of missing data. Based on the recovered data, the subspace identification method provides accurate estimates of the structure and parameter of the Buck converter synchronously. By applying the proposed method to a Buck converter, experimental results demonstrate its effectiveness. [ABSTRACT FROM AUTHOR]

In the field of electromagnetic compatibility (EMC) research, the knowledge of the formation mechanism of the far field electromagnetic radiation and its prediction is essential for the electromagnetic noise suppression design of a switched mode power supply. This paper investigates the equivalent driving sources of the common mode (CM) current of a Buck converter with cables. Based on the concept of CM voltage mutation, this paper proposes two mechanism models of the same‐direction CM voltage driving mode and the opposite‐direction CM voltage driving mode and derives the approximate analytical formulas for the far field intensity estimation of the horizontal cables. To evaluate the predictive effectiveness of the CM far field radiation model, a 30 MHz very high frequency (VHF) Buck prototype with shielded cables is built and tested, and a shielding shell and low impedance ground conductor suppression designs are then verified. The CM electromagnetic radiation mechanisms of a non‐isolated power converter are demonstrated here. The proposed electromagnetic radiation models, approximate analytical formulas, and improvement design can help to advance the CM radiation analysis and optimization design. [ABSTRACT FROM AUTHOR]

This paper proposes a new soft‐switching bidirectional multiport DC/DC converter for PV/EV applications. The proposed topology is capable of using several different sources simultaneously. Also, it has some benefits including high voltage gain, bidirectional, soft‐switching technique, and multi‐input multi‐output (MIMO) topology. In addition, all inputs of the proposed converter are separate from each other and it causes control of the outputs to be simple in the wake of the common ground of the inputs and outputs. The proposed converter can work on zero current switching (ZCS) conditions on some power semiconductors (power diode/switch) and decreases the switching and conduction losses. It also makes use of semiconductors with lower resistance on‐state (Rds‐on). Using coupled inductor techniques and working of semiconductors under ZCS conditions eliminates the total loss affected by reverse recovery of the power diodes, and a passive clamp circuit can recover the leakage energy released by the leakage inductance of the used coupled inductor. The proposed topology is built and tested in the laboratory. To confirm the accurate operation of the proposed topology, it is tested by Typhoon HIL‐404 emulator at 12 V–12 V–12 V inputs/270 W with 50 kHz switching frequency. [ABSTRACT FROM AUTHOR]

Abstract Modern power system networks are under statutory obligations to integrate renewable energy sources (RES). The primary reason is to meet ever‐increasing energy demand and also to curtail environmental pollution by greenhouse gases. However, the higher penetration of RES has the tendency of reducing inertia of overall power system network. Consequently, frequency stability is affected and deviates beyond allowable permissible limits leading to power blackouts, load shedding, and even total system failure. To address the issues associated with reduced inertia, an optimal control of hybrid energy storage system (HESS) has been proposed. HESS is basically a combination of battery and ultracapacitor, where ultracapacitor addresses rapidly varying power component by mimicking inertia while the battery compensates long‐term power variations. Thus, the HESS is effectively controlled to compensate the loss of inertia by regulating its energy flow. For the purpose of improved efficiency and better power management of the HESS, an improvised particle swarm optimization (MPSO)‐based virtual inertia control design has been proposed. The proposed MPSO is utilized to tune the gains of bidirectional dc–dc converter in such a way that improves frequency nadir with faster response to transient disturbances. This proposed method is simulated in MATLAB and its merits are validated in real time using hardware in loop. On analysing of the results, it can be observed that frequency nadir is improved by 48.96% with significant reduction in rate of change of frequency in comparison to conventional particle swarm optimization.

Abstract This paper proposes a new control method for loss reduction of two series buck converters. The proposed method can be applied to each series of buck converters with two power switches. To enhance the efficiency of the converter compared to other structures, a method based on determining operating cycles for loss reduction is employed, leading to increased output efficiency of the converter. Additionally, to demonstrate the efficiency improvement using the proposed method compared to the conventional approach, the efficiency of converter is calculated through theoretical computations under real conditions, and the output results are compared for both losses and efficiency. In addition, the proposed high‐buck converter in this paper benefits from a common ground advantage and exhibits a suitable conversion ratio. The high‐buck converters are used in numerous applications for situations with low voltage and low power. The most important applications for these converters are the power supply for mobile phones, tablets, and other portable electronic devices, battery chargers, and LED drivers. Here, in order to demonstrate the validity of the proposed method, the MATLAB‐Simulink results are provided. Moreover, in order to show the feasibility of the high‐buck converter, a 100‐W prototype has been implemented and the experimental results are provided.

Abstract The linear power amplifier (LPA) suffers from low power supply utilization in the DC power supply mode, leading to reduced output efficiency. This paper constructs an efficient power supply mode based on closed‐loop dynamic power supply system (CLDPSs). The CLDPSs can generate a pair of bipolar dynamic power supplies based on a predetermined signal to provide power to LPA, which can maintain a small voltage drop between the power supply and the output of LPA, thereby improving the power supply utilization of LPA. In addition, the study also focuses on the conflicting relationship between the output ripple and the dynamic performance of the CLDPSs, for which a new parametric design of the LC filter circuit is proposed, aiming to achieve a balance between these two aspects. Finally, a voice coil motor driving platform is constructed for experimental testing. The results demonstrate that the output ripple and dynamic performance of the CLDPSs can be balanced. In comparison to the DC power supply mode, the CLDPSs power supply mode can enhance the efficiency of LPA by 2 times while the driving accuracy of voice coil motor is basically unchanged.

Abstract This paper investigates and technically demonstrates a capacitive power transfer (CPT) system applicable to the charging of emerging very‐low‐power portable devices. The constant‐current operation of the primary LCL compensation in CPT is implemented and analysed to simplify the system design process and minimize the configuration on the receiving side. Additionally, the system design considerations for the capacitive coupler and the diode rectifier are presented based on the battery charging specifications. All the design concepts and considerations are validated through experimentation with a 13.56 MHz CPT system, which achieves load‐independent constant‐current output from full‐load to light‐load (one‐tenth of the full load) charging operations.

Abstract Dual active bridge (DAB) is an isolated DC‐DC converter gaining wider attention in power electronics applications. The high frequency (HF) transformer is an integral part of the DAB which is prone to saturation. Silicon carbide (SiC) based DAB are generally preferred for highly efficient power conversions, calling for an extremely low DC resistance of the transformer. This aggravates the DC bias issue significantly. The DC bias current generally flows due to the mismatch in static and transient switching of active devices, leading to eventual saturation of the transformer. This paper proposes an active method to precisely control the dead time of the devices (8–100 ns) without sacrificing the voltage utilization of the converter. This method does not require a sophisticated DC offset current measurement technique. The field programmable gate array (FPGA) based control platform on the gate driver side executes the proposed algorithm. The proposed control is experimentally verified in a 5 kW SiC based converter. The control implementation methodology is discussed with the support of necessary experimental results.

Abstract A dc voltage restorer (dc‐VR) with optimal droop control is developed to reduce the power loss and solve the dynamic current imbalance simultaneously of the zonal dc distribution system integrating multi‐parallel energy storage. Firstly, the power loss model composed of line loss and converter loss is built and it is proved to be a strictly convex function with respect to droop coefficients, which indicates the power loss can be mitigated by optimizing the current distribution. Thus, an image‐based droop optimization method is proposed to search for the optimal droop coefficients. Then, the economy of voltage compensation on power loss reduction is investigated and an ESS‐combined dc‐VR is designed, including an interleaved parallel architecture and a capacitor‐integrated electric spring (C‐ES). Unified virtual inertia is proposed for interleaved parallel bridge arms to make their dynamic performance consistent. And the newly introduced C‐ES can keep the bus voltage at the rated level to reduce the system cost. Therefore, the problem of dynamic currents imbalance is addressed from the points of converter structure (dc‐VR) and control system (unified inertia), and the power loss can be reduced by voltage recovery (C‐ES) and optimizing the current reallocation which is achieved by updating sharing coefficients from the image‐based droop optimization method. Finally, the simulation cases validate the effectiveness of the proposed optimal‐droop dc‐VR on dynamic current balance and power loss reduction, and hardware in the loop experiment results prove the consistent dynamic characteristics of the dc‐VR's arms.

Abstract The bidirectional DC‐DC conversion, as an important application scenario, places certain requirements on the topology structure. The four‐switch buck‐boost (FSBB) converter has received widespread attention due to its simple structure, flexible control and state switchability. However, the traditional control strategy makes it difficult to meet the requirements of high performance, high stability and high security at the same time. Furthermore, the control methods commonly adopted in domestic and international practical applications rely heavily on analogue control, which cannot maintain efficiency over a wide stability range. The use of digital control methods allows for optimized control algorithms, maintaining stable system operation and improving efficiency. Therefore, it is very important to use the digital control method to further improve the smoothness and steady‐state efficiency of the system multi‐mode switching while maintaining a wide input and output range, based on this, this study proposes two new three‐mode control modes: interleaved bias control mode and dual‐edge bias control mode.

Abstract The modular multilevel DC–DC transformer (MMDCT) provides a reliable solution to overcome the challenges of conventional dual‐active‐bridge converters in terms of power semiconductors ratings and dv/dt stress on transformer coupling windings. An alternative modulation method, quasi‐square‐wave, was proposed to reduce the cell capacitance of modular multilevel bridges. However the application of quasi‐square‐wave modulation is found to result in underdamped switching transients and losses when resetting energy stored in arm inductance. This paper presents a detailed transient analysis of MMDCT arm insertion based on an equivalent circuit, which contributes to a more accurate component sizing and gives voltage estimation for individual half‐bridge submodules. Additionally, a revised switching sequence is proposed to recover this inductor energy and lower the oscillation‐related losses. Simulated and experimental results from a scaled test rig of MMDCT are implemented and validate the proposed component sizing and switching sequence, indicating that the converter efficiency can be improved under revised switching sequence. Finally, a silicon carbide based, high‐frequency MMDCT is proposed and simulated.

Abstract A soft switching non‐isolated bidirectional DC–DC converter with an improved voltage conversion ratio without any additional auxiliary switch is presented in this paper. In the proposed converter, improved step‐up/step‐down gain conversion is achieved by employing the coupled inductors method. Also, the auxiliary circuit provides soft switching conditions for all the semiconductor elements, regardless of the power flow direction and without any extra voltage stress. The other switch helps provide soft switching conditions for the main switch. Moreover, the switch used for providing soft switching conditions operates as a synchronous rectifier as well. The additional circuit added to attain soft switching is composed of an inductor, coupled with the converter's main inductor, and two auxiliary diodes. The auxiliary diodes benefit from zero‐current‐switching conditions. Fully soft switching conditions for all semiconductor devices, removing the reverse recovery problem, and a low number of components have led to mitigating switching losses and improving efficiency. Detailed operating principles and a theoretical analysis of the proposed converter are presented. Also, the experimental results of a 220 W prototype circuit are provided to confirm the validity of the proposed topology.

Abstract For cooperation among distributed generations in a DC microgrid (MG), distributed control is widely applied. However, the delay in distributed communication will result in steady‐state bias and the risk of instability. This paper proposes a novel distributed control for time‐delayed DC MGs to achieve accurate current proportional sharing and weighted average voltage regulation. Firstly, by utilizing an advanced observer based on the PI consensus algorithm, the steady‐state bias problem is addressed. Then, using the passivity theory, stability analysis is conducted to reveal the principle of system instability caused by communication delay. On this basis, to offset the adverse effects of communication delay on the system stability, scattering transformation is introduced in the observer‐based distributed control. Moreover, considering the potential delay from the measurement stage in real‐life scenarios, the sufficient condition of the system stability is concluded by constructing the Lyapunov–Krasovskii functional. Finally, the performance of the proposed control and conclusions of stability analysis are verified by hardware‐in‐loop tests.

Abstract This paper presents a non‐isolated DC‐DC converter designed to validate ultra‐high voltage gain using a modified double boost mode. The objective is to achieve exceptionally high voltage gain by integrating a modified triple boost technique (MTBT), interleaved with second main and auxiliary third MOSFETs, and a modified switched inductor‐capacitor (MSLC), effectively doubling the voltage transfer gain. Furthermore, MSLC is combined with the auxiliary third and double main MOSFET to double the voltage gain while concurrently mitigating voltage stress on the auxiliary MOSFET and diodes in the proposed converter (the PC). Additionally, all diodes in the MTBT operate under zero current switching (ZCS) and the double main and auxiliary third MOSFET face very low current stress at ultra‐high voltage gain. The input current of the PC remains steady without pulsating at a low duty ratio, making the PC more suitable for renewable energy systems. The PC offers numerous advantages, exhibiting high efficiency and ensuring minimal voltage stress on power devices with low current stress on the power switches. Notably, PC aims to elevate input voltages from 30 V to a variable output range of 335 to 600 V, delivering 440 watts at 96.1% efficiency.

Abstract The DC–DC conversion stage of a three‐stage solid‐state transformer is the most challenging due to the combination of high power, medium voltage, and medium frequency. This combination also causes most of the losses in the DC–DC stage. To address this issue, a new asymmetrical quadruple active bridge series resonant DC–DC converter (AQAB‐SRC) has been proposed as a building block for solid‐state transformers. The converter achieves soft switching of all switches throughout the operating range by extending and using the half‐cycle continuous conduction mode control strategy. It also has fewer high‐frequency transformers compared to other converters, as more bridges are connected to the same multi‐winding transformer. The optimal design of AQAB‐SRC has been analyzed theoretically, and simulation and lab‐scale experimental results have been obtained to validate the feasibility and validity of the proposed topology.

Abstract A data‐driven Buck converter model identification method is proposed to deal with missing (incomplete) outputs, which is robust to the data length and percentage of missing data. A nuclear norm based convex optimization problem instead of linear interpolation, to guarantee the recovered missing data satisfying the potential model structured low‐rank character, is constructed to estimate missing outputs. The alternating direction method of multiplier strategy is used to solve the nuclear norm based convex optimization problem. In this way, the high‐quality missing data can be estimated, even for short data length and high percentage of missing data. Based on the recovered data, the subspace identification method provides accurate estimates of the structure and parameter of the Buck converter synchronously. By applying the proposed method to a Buck converter, experimental results demonstrate its effectiveness.

Abstract In the field of electromagnetic compatibility (EMC) research, the knowledge of the formation mechanism of the far field electromagnetic radiation and its prediction is essential for the electromagnetic noise suppression design of a switched mode power supply. This paper investigates the equivalent driving sources of the common mode (CM) current of a Buck converter with cables. Based on the concept of CM voltage mutation, this paper proposes two mechanism models of the same‐direction CM voltage driving mode and the opposite‐direction CM voltage driving mode and derives the approximate analytical formulas for the far field intensity estimation of the horizontal cables. To evaluate the predictive effectiveness of the CM far field radiation model, a 30 MHz very high frequency (VHF) Buck prototype with shielded cables is built and tested, and a shielding shell and low impedance ground conductor suppression designs are then verified. The CM electromagnetic radiation mechanisms of a non‐isolated power converter are demonstrated here. The proposed electromagnetic radiation models, approximate analytical formulas, and improvement design can help to advance the CM radiation analysis and optimization design.

Abstract This paper proposes a new soft‐switching bidirectional multiport DC/DC converter for PV/EV applications. The proposed topology is capable of using several different sources simultaneously. Also, it has some benefits including high voltage gain, bidirectional, soft‐switching technique, and multi‐input multi‐output (MIMO) topology. In addition, all inputs of the proposed converter are separate from each other and it causes control of the outputs to be simple in the wake of the common ground of the inputs and outputs. The proposed converter can work on zero current switching (ZCS) conditions on some power semiconductors (power diode/switch) and decreases the switching and conduction losses. It also makes use of semiconductors with lower resistance on‐state (Rds‐on). Using coupled inductor techniques and working of semiconductors under ZCS conditions eliminates the total loss affected by reverse recovery of the power diodes, and a passive clamp circuit can recover the leakage energy released by the leakage inductance of the used coupled inductor. The proposed topology is built and tested in the laboratory. To confirm the accurate operation of the proposed topology, it is tested by Typhoon HIL‐404 emulator at 12 V–12 V–12 V inputs/270 W with 50 kHz switching frequency.

Abstract This paper proposes an extended DC‐DC converter with high voltage conversion ratio and soft‐switching ability. The proposed converter has active switched‐inductors, switched‐capacitors included in the conventional high gain converter and operates in continuous conduction mode (CCM). Simple auxiliary resonant elements are added on the primary leg of the converter to provide design freedom for soft‐switching operation. The significant merits of the proposed converter are lesser voltage and current stresses, high voltage gain with reduced component count and better efficiency. Additional feature of this converter is soft‐switching operation under different load conditions and duty ratios without considerably increasing stresses. The zero voltage switching (ZVS) turn‐on operation is obtained for all switching devices. Therefore, switching power losses are minimized greatly. This paper presents the description, principles of operation and steady state analysis in comparison with the existing high gain converters. The theoretical analysis is verified with a 350 W prototype operated at input is 20 V and output is 220 V. The overall efficiency achieved is 96.7%. The obtained results confirm ZVZCS operation at full load.

Abstract In the inductive power transfer (IPT) system, using multiple coil branches instead of a whole large coil can effectively solve the thickness problem and save space. In that case, there are small parameter differences in mutual inductance and self‐inductance between the coil branches in parallel. These differences are amplified in high‐frequency IPT systems, resulting in different currents flowing through the different coil branches. The current unbalance will create many hazards. Therefore, this paper analyzes the key factors that cause current to unbalance and studies the equivalent circuit model of an inductive power transfer system with secondary multiple parallel branches. Moreover, this paper designs the compensation circuit and studies two kinds of current balance methods. Furthermore, the parameter design criteria are detailed to obtain a nearly ideal current balance effect. The characteristic analysis, parameter design, and verification are described in detail.

Abstract The presented work discusses issues related to the use of modern multiphase topologies of Dual Active Bridge (DAB)‐type converters. Converters of this type are widely used in most DC microgrid applications. The introduction emphasizes a comparative analysis between single‐phase and multi‐phase DAB topologies within high‐power DC microgrids, delving into their respective advantages, drawbacks, design procedures, and considerations based on the latest knowledge. The publication explores the comparison and selection of viable topologies for deployment in high‐power and high‐efficiency DC microgrids. The unified method of controlling 1‐phase and multi‐phase DAB converters was proposed in this design, simplifying the issues of DC microgrid control. All topologies were tested on the same controller concept. The study performs laboratory investigation of DAB 1‐phase and 3‐phase: Star–Star, and Star–Delta topologies. Attention was paid to maintaining uniform operating conditions of the system, contrary to studies known from the literature, all tests were carried out on the same laboratory stand and the same magnetic components in different configurations. Analytical and laboratory analyses of the Zero Voltage Switching (ZVS) region were performed, accounting for non‐linear phenomena. Based on these findings, an assessment of the system's performance in soft switching was carried out. The presented results were implemented in a simulation model and subsequently validated through tests on a constructed laboratory setup to ensure the proper operation of the system. This work meticulously presents and discusses variations in efficiency, dynamic response, phase current harmonic distribution, phase shift distribution, ZVS switching region, and more among the examined topologies. To ensure a fair comparison, the converter configuration for both simulation and laboratory models utilized identical components across all configurations.

Abstract In electric vehicles (EVs), the low voltage dc‐dc converter (LDC) with synchronous rectifier switches (SRs) can be used to reduce conduction loss caused by the high load current and improve the efficiency. Therefore, it is important to design a proper turn‐on time of SRs. As a popular driving strategy for the SRs, the drain–source voltage across the SRs is sensed to generate the gate driving signal. However, when LLC dc–dc converter operates at O mode, there will be a voltage ringing across the SRs. If the ringing voltage reaches to the threshold voltage −Vth,on, it would make SRs turn‐on early and results in abnormally working of the converter. The novelty and contribution of this paper lie in: (1) elaborating on the voltage ringing across the SRs, (2) the accurate ringing model is established during O mode, and (3) a simple, lossless, and low‐cost filter circuit is used to solve the negative effect of the ringing voltage for LLC converter at high load current. A 1.26 kW experimental prototype with ≈250–430 V wide input voltage and ≈9–16 V wide output voltage is implemented, 96.7% peak efficiency and 96% full load efficiency are achieved with a 3.12 kW/L power density. The theoretical analysis has been validated by the simulated and experimental results, and the SR LLC dc–dc converter with the SR works efficiently and reliably with the proposed solution at a high load current.

Abstract Due to galvanic isolation, bidirectional power transmission and extensive voltage adjustment, dual active bridge (DAB) exerts significant interface between renewable sources and electric vehicle (EV) storage port. However, for DAB operations, under light load or high voltage gain conditions, minimization of root‐mean‐square (RMS) current (MRMS) causes a restricted soft‐switching range. With variations of output power and operation modes, maintenance for all switches ZVS operation is difficult to maintain. Therefore, here, a segmented‐region optimum modulation (SROM) scheme based on extended‐phase‐shift (EPS) control is proposed to solve the aforementioned problems and solve complicated coupled relationship among different optimization methods. Firstly, based on voltage gain and transmission power, all EPS modes are divided clearly. Then, for switching loss reduction, fully‐power‐range ZVS (FZVS) is realized through transitions among EPS modes. Thirdly, either all semiconductors ZVS or not, most suitable optimization method is selected for different EPS regions by SROM. Further, to establish accurate boundaries among these optimization methods, relationship between inner phase‐shift ratio D1 and outer phase‐shift ratio D2 are quantified by unified parameter algorithm with unified parameter m. Therefore, for any EPS modes, efficiency is promoted comprehensively. A DAB‐based prototype is established and experimental results verify correctness and effectiveness of proposed method.

Abstract In this paper, a reduced‐switch‐count two‐phase interleaved LLC converter with precise current balancing is proposed by using switching‐control‐capacitor (SCC) technology. Compared with the conventional SCC‐LLC converter, the proposed two‐phase SCC‐LLC converter reduces the switch count with the SCC circuits, and achieves excellent current sharing under all the tolerance conditions between the two‐phase resonant elements. In the proposed converter, the SCC circuit is only used in the first phase. The design of the SCC circuit parameters is analyzed to reduce the voltage stress of the SCC circuit and to ensure that two‐phase currents are balancing with large tolerance of resonant elements. A 2.16‐kW GaN‐based two‐phase interleaved SCC‐LLC converter prototype is established for data center application, and the experimental results show that the 98.1% peak efficiency, the 97.6% full load efficiency, and higher than 96% efficiency at the wide range from 3‐A to 40‐A load current are achieved. The precise current sharing lower than 1% is achieved by using a cheap ceramic capacitor with high tolerance, which validates the performance of the converter.

Abstract This paper proposes a new DC–DC bipolar resonance converter that combines a dual‐active‐bridge and a multi‐port resonance Buck‐Boost converter. This structure uses a resonance network between the input and output ports, which has the following advantages: it creates a constant current supply in the open‐loop mode; it keeps the current phase of the output ports constant under different loads; and it allows reversing the power from any output port by adjusting the phase shift of its switches, if the converter is connected to a DC microgrid. In this way, power can be exchanged among each of the output ports and input ports. The advantages of this converter are bidirectional power exchange, power exchange between output ports, soft switching, high efficiency, integration of transformer parasitic elements, and the modular capability to connect multiple resources at the input. Furthermore, the proposed structure of the bipolar converter has been implemented for verification purposes, and its results are presented in three modes: open loop, voltage control, and current control. Additionally, the results of different modes of power sharing and their bidirectionally are shown.

Abstract Three‐coil inductive power transfer (IPT) charging system can not only achieve inherent constant current (CC) to constant voltage (CV) transition but also tolerate load open‐circuit. However, due to the cross‐coupling between the auxiliary coil and the receiver coil, the output voltage in CV mode may deviate from the CV voltage significantly, which makes the design freedom of the three‐coil coupler low. By replacing the auxiliary coil with a transformer, an improved auxiliary circuit is proposed in this paper to address the cross‐coupling issue and to increase the design freedom of the loosely coupled transformer (LCT). The improved auxiliary circuit can achieve load short‐circuit and open‐circuit protection. Besides, the optimization design of LCT is easy to achieve by load impedance matching. The operating principle and parameters design of the improved auxiliary circuit are discussed. A 1 kW experimental prototype is built to verify the feasibility of the proposed method.

Abstract Environmental issues and the global need to increase economically sustainable access to electricity addressed and boosted scientific research and use of Distributed Energy Resources, such as solar Photovoltaic (PV). Multi‐port power converters can be of great interest for a compact and efficient interface between PV, storage units, and DC loads. The Triple Active Bridge (TAB) shows interesting advantages in terms of isolation and Zero Voltage Switching capabilities over wide load and input voltage ranges. This work aims to develop a TAB prototype for a NanoGrid (NG) application, analyzing the possibility of a direct interface of PV modules, storage units, and DC loads, without the use of intermediate conversion stages. The TAB prototype uses Gallium Nitride devices, and an evaluation of the overall efficiency is provided, useful to compare with other isolated three‐port converters. Through an analytical approach, a TAB has been sized and optimized to meet specific application requirements. MATLAB/Simulink simulations have been done for the sizing validation and the control strategy design. A prototype has been developed and experimental measurements have been compared with simulation results. The TAB is proposed as a key element of DC NGs, but applications of interest are also automotive, More Electric Aircraft, and naval applications.

Abstract Isolated multiple port DC/DC converters, such as the Multiple Active Bridge (MAB) converter, have many recent applications, such as interconnection between grids, isolated uninterruptible power sources (UPSs) and electric vehicle chargers. MAB converter is an attractive solution from the point of view of the hardware because of its symmetry and its capability to be extended to any number of bridges with a moderate number of components. However, the main challenge of this converter is the control method in order to achieve independent control between the different ports and to minimize recirculating currents. For that reason, three‐port power converters have been already investigated, but many improvements can be done for a larger number of ports. This paper proposes to use a Fourier decomposition for the main power signals to separate their real and imaginary parts. As the signals work at the switching frequency, this decomposition is developed with analog electronics. Based on that, a general control method for regulating the power at the different ports is presented using the first harmonic component, which delivers most of the power. In this proposal, two nested control loops ensure accuracy for the DC power flow. Simulation and experimental results validate the proposal.

Abstract The most challenging aspect of utilizing model predictive controllers (MPCs), particularly those involving power electronic applications, is the extraction of a model that accurately represents the behavior of the studied system. Concerning the use of power electronic applications, as long as an MPC is used, adjusting the controller parameters brings difficulties. In addition, as the number of elements increases, it becomes harder to get the best control law out of the model. To do away with the need for model extraction, this study presents an offline data‐driven approach in conjunction with the MPC that can optimally adjust the MPC parameters based on the iterative feedback tuning (IFT) algorithm called the iterative feedback predictive controller (IFPC). The proposed method eliminates concerns regarding selecting an optimal number of algorithm iterations, thereby reducing operating costs, by introducing a modified IFT called feedback‐based IFPC (FIFPC) while simultaneously achieving optimal MPC parameters. The proposed method is applied to a constant voltage load (CVL) connected less‐than‐ideal buck converter, that is, one with perturbed filter elements and variable loads. A robust stability analysis (RSA) is performed under normal operating conditions to investigate the robustness behavior of the proposed controller. Simulation studies are presented to evaluate the proposed controller under different scenarios, such as step and abrupt load changes and measurement noise, compared with the well‐known model‐based and data‐enabled predictive controller (DeePC) approaches in the MATLAB/Simulink environment.

Abstract Direct current microgrid (DCMG) clusters are gaining popularity in power systems due to their simplicity and high efficiency. However, DCMG clusters are susceptible to minor disturbances due to low system inertia. This paper proposes a method to enhance the small‐signal stability of a DCMG cluster by optimizing the main control parameters of the system. This paper presents a small‐signal state‐space model of a DCMG cluster system at the system level, considering a multi‐bus network topology. Then, the control parameters that significantly affect the small‐signal stability of the DCMG are selected using the participation factor method. To enhance the system damping, the Pareto‐optimal frontier of the bi‐objective problem was determined using the elite non‐dominated sorting genetic algorithm (NSGA‐II). The optimal compromise is determined by using the fuzzy membership function method to extract it from the generated Pareto optimal front. The proposed method has been verified on a three‐sub DCMG test system with droop control.

Abstract LLC resonant converters are widely adopted in many different industrial applications due to their high efficiency operation. To further improve LLC resonant converters' efficiency, the secondary unregulated diode rectifier is replaced by the synchronous rectifier (SR). In many applications, LLC converter is designed to operate at resonant frequency to maximize the system efficiency and act as a DC transformer (DCX). The SR driving signal is set as the same as the primary driving signal to work in an open‐loop mode. However, the resonant frequency will deviate due to the tolerance, working environment, and ageing effect of circuit components, which will lead to the degradation of the system efficiency and output voltage variation. Unfortunately, most of the existing techniques cannot be simply adopted in SR LLC DCX. Therefore, an adaptive SR driving strategy that can compensate the circuit components' variations is necessary for SR LLC DCX. Inan adaptive SR strategy based on the constant voltage gain characteristic at resonant frequency point is proposed. The proposed strategy is applicable for all different scenarios with easy implementation and low cost.

Abstract Most high‐gain step‐up dc‐dc structures operate with a limited duty cycle and suffer from a high component count, limiting their application. This paper addresses these problems by proposing a new step‐up dc‐dc converter that provides a high conversion ratio with few elements. Two coupled inductors are used instead of conventional voltage multiplier cells to improve the gain without excessive components. The topology includes one switch whose duty cycle is not limited and can vary between zero and one according to the output voltage condition. It has been placed on the low‐voltage side of the converter that encounters low‐voltage stress. It is selected from low‐voltage rating switches with small on‐resistance, which reduces the conduction loss of the switch and improves the efficiency. High boost factor, high efficiency, reasonable component counts, improved gain‐to‐element ratio, and low voltage stress on the switch distinguishe the converter from their counterparts. The topology also benefits from the common‐ground feature. However, its input current waveform is pulsating. This article describes the theory and operation principle of the topology in detail. Experimental results are represented to evaluate the converter's performance and operation. In this case, a 240 W prototype has been designed and fabricated. Results confirm the above claims.

Abstract The integration of supercapacitors as hybrid energy storage systems in electric vehicles has attracted the attention of many researchers and has been considered as a promising solution. Bidirectional DC/DC converters (BDDCs) play a fundamental role in HESS, as they manage the power flow by controlling currents and regulating the DC bus voltage. However, they encounter the challenge of uncertainties and high fluctuation power loads, necessitating the fast dynamics, stability, and high robustness of the controller. This paper proposes a novel hybrid proportional–integral and backstepping cascade controller to regulate the DC‐bus voltage under uncertainties and load variations, and to control the current references of the on‐boarded sources. To confirm the asymptotic stability of the whole system, a nonlinear stability analysis is conducted using the Lyapunov theorem. A power management strategy is applied to distribute the power loads and generate reference currents for the BDDCs controller. Simulations results under various driving cycles using MATLAB/Simulink demonstrate the superiority of the proposed controller compared to conventional proportional–integral and backstepping controllers. A real‐time controller‐hardware‐in‐the‐loop test bench is developed to validate the effectiveness of the proposed strategy.

Abstract This paper investigates the stability and reliability analysis of a non‐isolated high‐gain DC‐DC converter. The proposed DC‐DC converter produces a high gain output voltage with a lower duty ratio and reduced voltage stress on the semiconductor switch. A reliability analysis is performed to predict the failure rate and lifetime of the individual components using the military handbook (MIL‐HDBK‐217F). A state space equation and small signal modeling of the proposed converter are derived to elucidate the performance of the proposed converter through stability analysis. A closed‐loop using PID controller is incorporated to attain the constant regulated output voltage during sudden parameter changes. The validation of the closed‐loop using the PID controller is verified with the wide range of variations in the different parameters, such as input voltage, load value, and reference voltage value. The laboratory‐based prototype is developed for the proposed converter and validated the performance with 250 W. The power density and efficiency of the proposed converter are 1.360 kW/L and 93%, respectively.

Abstract Here, a high gain DC–DC converter which is based on switched capacitor (SC) and switched LCL (SLCL) cells is presented. The diode employed in the classical passive switched inductor (SI) cell is replaced by a capacitor in the proposed SLCL cell to achieve higher voltage gain. Two switches—one each in the positive and negative DC rails of the supply are employed to charge and discharge the inductors of SLCL cells. A generic structure comprising of N and M number of SLCL cells in the positive and negative DC rails respectively along with K number of SC cells is presented. To validate the proposed gain extension concept, a two‐switch based converter comprising of 2 SLCL and 1 SC cells is synthesized and its operation is described in detail. The voltage gain expression of the proposed SLCL‐SC converter is derived. Experimental results are obtained from a 25 to 380 V prototype converter which operates at a full‐load efficiency of 94.22% at 200 W. Since the switches employed in the proposed converter are operated at a moderate and safe duty ratio of D = 0.51, the voltage stress on the switches is about 25% of the output voltage while the diodes are subjected to even lesser voltage stress levels of only one‐fifth of the output voltage. The main salient features of the proposed topology are its (i) modular structure, (ii) ability to provide higher voltage gain values at lower duty ratios (iii) reduced voltage stress on the semiconductor devices and (iv) reduced conduction losses due to the replacement of diodes with capacitors in SLCL cells.

Abstract This paper introduces a novel approach for designing a Wireless Power Transfer (WPT) system with LCC‐S compensation. Since WPT systems operate under resonant conditions, even small deviations of the components from the nominal values can result in a significant reduction of the power transferred to the load, and in an increment of the circulating currents, reducing the system efficiency. The design techniques available today in the literature provide a unique combination of passive components capable of transferring a certain power to the load. This is a limitation, because, in practice, there are several combinations that allow reaching the desired output power, but they are usually neglected because they are extremely difficult to compute analytically. For this reason, in this paper, the authors present an innovative design procedure that enables, through a Genetic Algorithm, the identification of multiple feasible combinations of the LCC‐S components capable of achieving the desired output power. Moreover, the authors evaluate the effects of the component tolerances on the output power to determine which combinations are more robust to component variations. This task is performed by calculating the probability that a particular combination yields the desired output power, once the tolerances have been considered, following a Monte Carlo approach. This information is utilized to decide whether it is possible to reduce the component quality (worsening the tolerance) without affecting the performance. Finally, an optimal solution granting both low‐cost and robustness against component tolerances can be individuated. The proposed design procedure is applied to a case study and validated experimentally.

Abstract High efficiency and unity power factor (PF) are the most important requirements of a wireless charger system simultaneous with the output voltage regulation. Achieving all above‐mentioned criteria in a wide range of the load is challenging in the system. This paper presents a novel control approach applied to series‐series wireless power transmission converter by using a dual‐function compensator to achieve unity PF and maximum efficiency during the constant power‐constant voltage (CP‐CV) charging scenarios. A semi‐active rectifier with impedance matching capability along with a switch‐controlled capacitor constitutes the dual‐function compensator on the secondary side. Meanwhile, the primary side inverter executes the CP‐CV charging scenario for the battery with various charging characteristics at a fixed‐switching frequency. Besides that, all secondary side switches experience soft switching condition throughout the battery charging. Finally, a prototype with a power of 200 W and roughly regulated efficiency of 90% is presented in order to verify the proposed control method.