Search

Copyright of Revista Odonto Ciencia is the property of EDIPUCRS - Editora Universitaria da PUCRS and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

We used finite element analysis to assess stress on the cortical bone and plate fixation system, as well as mandibular resistance after sagittal split ramus osteotomy with different mandibular advancements and rotations of the occlusal plane. Three-dimensional mandibular models were obtained, and 6mm and 12mm advancements were planned associated with linear, clockwise, and counter-clockwise rotation of the angle of the occlusal plane. Each model was then fixed with one or two 2.0mm system plates and secured with four monocortical screws. A total of 12 models were built and subjected to a vertical load in the lower central incisor ranging from 50N to 500N in 50N increments. Results showed that the 12mm advancement was associated with higher stress on the bone and plate surface. Additionally, the models fixed with two plates exhibited lower plate stress than those fixed with a single plate. Counter-clockwise rotation of the angle of the mandibular plane in the 6mm advancement caused more plate stress, which did not occur in the 12mm advancement. This analysis has shown that change in the occlusal plane in large mandibular advancements does not act as an additional stress factor. These findings can help to better understand the tensions on bone and plate surfaces in patients who need large mandibular advancements that are associated with a change in the occlusal plane, and will aid better surgical planning., (Copyright © 2020 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.)

The aim of this study was to perform a literature review on the use of finite element modeling (FEM) for the evaluation of the biomechanical behavior of temporomandibular joint replacement (TMJR) devices. An electronic search of online medical and scientific literature database was conducted using selected search terms. The search identified 307 studies, of which 19 were considered relevant to this study. Of the 19 selected studies, 10 (52.6%) investigated the influence of geometry and fixation methods, while two (10.5%) evaluated the behavior of artificial condyle-fossa structures. The TMJR devices assessed in these studies included TMJ Inc. (aka Christensen; 63.2%), Zimmer Biomet (15.7%), Stryker (10.5%), and a theoretical intramedullary condylar component (5.3%); 26.3% of the studies evaluated custom TMJR devices. Such studies provided important data on the distribution of strain and stress through TMJR structural components and surrounding bone by using different software systems and methods. The mean stress values were lower on a custom TMJR condyle-ramus component and the supporting bone than on the stock device. FEM proved to be an accurate and valuable biomechanical simulation tool for studying the current TMJR devices and should be considered a useful tool for the improvement and development of future joint replacement devices., (Copyright © 2018 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.)

This study constituted a comparative assessment of the mechanical resistance of square and rectangular 2.0-mm system three-dimensional miniplates as compared to the standard configuration using two straight miniplates. 90 polyurethane replica mandibles were used for the mechanical trials. Groups 1, 2, and 3 simulated complete symphyseal fractures characterized by linear separation of the central incisors; groups 4, 5, and 6 simulated parasymphyseal fractures with an oblique configuration. Groups 1 and 4 represented the standard method with two straight miniplates set parallel to one another. Square miniplates were used in groups 2 and 5, and rectangular miniplates in groups 3 and 6. A universal testing machine set to a velocity of 10mm/min and delivering a vertical linear load to the first left molar was used to test each group. Maximum load values and load values with pre-established dislocation of 5mm were obtained and submitted to statistical analysis using a calculated reliability interval of 95%. The mechanical performances of the devices were similar, except in the case of rectangular plates used in the parasymphyseal fractures. The innovative fixation methods used showed significantly better results in the case of symphyseal fractures., (Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.)