Search

Purpose: To evaluate the response of human peri-implant soft tissue (PIST) to different healing abutment materials 24 hours after positioning by assessing the expression of genes related to the early connective tissue wound healing response. Materials and Methods: The following four materials were used to create experimental abutments that were mounted on implants placed in five patients (four different abutments in each patient): group A--grade 4 titanium (Ti), group B--grade 5 Ti, group C--zirconia (Zr), and group D--polyetheretherketone (PEEK). Before implant placement, a gingival biopsy (control, CT) sample was obtained using a 2-mm-diameter punch (T0). After 24 hours, PIST biopsy samples were collected using a specifically designed custom-made cutting device. Real-time polymerase chain reaction (PCR) was performed to analyze the expression of the following genes: COL-I, COL-III, MMP-1, TIMP-1, TGF-^1, FN, ITGA4, ITGA5, ITGB1, RAC-1, COL-IV, aSMA, IL-6, and CXCL-1. Results: Gene expression analysis showed some differences between CT and the experimental groups; however, no significant differences were detected when comparing the experimental groups. COL-I was significantly downregulated in groups A and C compared to CT. Expression of MMP-1 and TIMP-1 increased in all the experimental groups but to a lesser extent in group A. FN, RAC-1, COL-IV, and aSMA were downregulated, especially in group A, in which CXCL-1 and IL-6 showed the lowest expression. Conclusions:The results of grade 4 Ti and Zr abutments seem to be promising, because a lower expression of genes related to inflammation, myofibroblast activation, and extracellular matrix remodeling was observed when compared with grade 5 Ti and PEEK, without triggering a profibrotic response in the early phases of PIST repair. [ABSTRACT FROM AUTHOR]

Purpose: To evaluate the clinical performance of implant-prosthetic rehabilitations carried out using ceramic-coated CAD/ CAM titanium abutments. Materials and Methods: Thirty implants were placed in 30 patients and rehabilitated with 30 single crowns attached to CAD/CAM titanium abutments. A conventional procedure was applied, implants were placed after postextraction socket healing, and prosthetic restorations were placed after implant healing. Implant lengths ranged from 6 to 15 mm, and widths were 3.6, 4.2, and 4.8 mm. At the time of prosthesis delivery (T0), after 2 years (T1), and after 5 years (T2), the Plaque Index (PI), bleeding on probing (BoP), pocket probing depth (PPD), marginal bone level (MBL), and pink/white esthetic scores (PES/WES) were evaluated for each implant. Results: No patient dropped out of the study during the follow-up period. All 30 implants were clinically successful 5 years after prosthesis delivery (survival rate: 100%) and showed no signs of peri-implant infection. Peri-implant soft tissues were in good health (BoP at T2: 0% in 73% of patients; 25% in 13% of patients; 50% in 10% of patients; and 75% in 3% of patients). The mean PPD was 2.05 ± 0.56 mm at T0, 1.992 ± 0.6 mm at T1, and 1.867 ± 0.439 mm at T2. The mean MBL was 0.413 ± 0.440 mm at T0, 0.306 ± 0.388 mm at T1, and 0.263 ± 0.368 mm at T2. The mean PES, WES, and PES/WES indices (7.43 ± 1.04, 7.57 ± 0.82, and 15.00 ± 1.17, respectively) indicate good integration of soft tissues, satisfactory esthetics, and overall positive outcomes. Conclusions: The success rates, maintenance of MBLs, and periodontal and esthetic indices suggest the validity of implant-prosthetic rehabilitations with CAD/CAM abutments in cases of single crowns. [ABSTRACT FROM AUTHOR]

The article offers update on several research on dental implant fracture. Topics of the studies include fractures of titanium implants, fractures that occurred in implant brands that are no longer commercially available, impact of surface modifications on the fracture resistance of aged zirconia implants in vitro, implantoplasty and fracture risk of implants that underwent implantoplasty.

Objectives: To evaluate clasp-retained removable partial dentures (C-RPDs) with a metal framework for survival, maintenance requirements, and biologic implications. Method and materials: C-RPDs were retrospectively analyzed based on patient records. Treatment failure was defined as fracture of a framework component (metal base or connector) or loss of an abutment tooth. Other outcome variables included factors that might conceivably impact C-RPD survival (maxilla vs mandible, Kennedy classes, opposing dentitions, treatment by students vs certified dental practitioners), mobility and caries of abutment teeth (in relation to clasp designs), and maintenance requirements (relining, clasp or resin fractures). Differences were evaluated by appropriate statistical tests at the P≤.05 level. Results: A total of 612 patients (339 men, 273 women) 60.0±11.5years old at delivery were included, covering 842 C-RPDs and a mean observation period of 42.1±33.2months. Kaplan-Meier C-RPD survival was 76.2% after 5years and 49.5% after 10years. Biologic complications (ie, loss of abutment teeth) accounted for the vast majority (95.6%) of C-RPD failures, and Kaplan-Meier C-RPD survival was significantly better in the mandible (P=.015). Some clasp designs contributed significantly to caries and removal of abutment teeth (both P<.05). No other significant differences were noted. Conclusion: Tooth loss both emerges as the main cause of C-RPD failure and might be amenable to careful selection of clasp designs. Overall, better C-RPD survival should be expected in the mandible. A noncon-tributory role of Kennedy classes and opposing dentitions is tentatively suggested based on numerically heterogenous subgroups. [ABSTRACT FROM AUTHOR]

Purpose: To compare the color dimensions, color discrepancies (E00), and surface roughness of milled materials before and after application of a bleaching agent. Materials and Methods: A total of 10 extracted molars were obtained. Each tooth was cut in transverse sections to create disks (3-mm thick, 10-mm diameter; control group). Disk specimens of eight materials (n = 10 per group) were fabricated: polymethyl methacrylate (PMMA) interim material (PMMA-Telio group), two resin nanoceramics (RNC-Ultimate group and RNC-Cerasmart group), two hybrid ceramics (HC-Shofu group and HC-Enamic group), lithium disilicate (LD-Emax group), zirconia-reinforced glass ceramic (ZGC-Suprinity group), and zirconia (Zr-InCeram group). Color measurements were obtained using a spectrophotometer before and after applying 35% hydrogen peroxide-based bleaching agent. Pre- and postbleaching surface roughness (Sa) analyses were completed using a profilometer. Results: Significant L*, a*, b*, and E00 value differences were found (P < .05). Color discrepancies (E00) ranged from 0.30 ± 0.14 to 4.82 ± 0.10. The highest color discrepancies were measured on the PMMA-Telio group, while the lowest color discrepancies were computed for ZGC-Suprinity, RNCUltimate, and RNC-Cerasmart. Significant surface roughness differences were found (P < .05). The largest increase of surface roughness values between the pre- and postbleaching measurements was obtained in the PMMA-Telio group with a mean Sa value of 4.73 ± 3.02, while the largest decrease of surface roughness values between the pre- and postbleaching measurements was obtained in the Zr-InCeram group with a mean Sa value of -1.58 ± 0.10. Conclusions: The milled materials showed significant pre- and postbleaching color and surface roughness discrepancies. [ABSTRACT FROM AUTHOR]

Purpose: To investigate the esthetic outcomes based on the color differences in zirconia (Zr) of varying thickness, resin cement color, and types of titanium (Ti) implant surface treatments. Materials and Methods: Overall, 28 high-translucency monolithic zirconia (HTMZ) specimens were arranged into four groups based on Zr thickness: 1.0, 1.5, 2.0, and 2.5 mm (n = 7 per thickness). Each group was tested using two resin cement colors (clear and opaque) in combination with six surface-treated Ti groups (n = 7), including untreated titanium (UT), anodization (AN), 50-µm alumina airborne-particle abrasion followed by AN (SBAN), AN followed by 50-µm alumina airborne-particle abrasion (ANSB), 9.5% hydrofluoric acid followed by AN (HFAN), and AN followed by 9.5% hydrofluoric acid (ANHF). This created a total of 48 experimental groups, including the use of composite resin (n = 7, shade A2D) for four control groups. All specimens were measured using a spectrophotometer and subsequently compared with composite resin (control) with the corresponding Zr thickness to establish color differences. A color difference of < 2.7 was considered clinically acceptable. The data obtained were statistically analyzed using ANOVA and post hoc test (P = .05). Results: Zr thickness, resin cement color, and type of Ti implant surface treatment significantly affected the observed color differences (P < .05). When using 2.5-mm HTMZ with clear resin cement on AN, UT, SBAN, HFAN, and ANSB, the mean color differences were below the clinically acceptable values, and the 95% CIs of color differences were below the clinically acceptable values for AN, UT, and SBAN groups. Conclusions: HTMZ with a minimum thickness of 2.5 mm and clear resin cement on AN, UT, and SBAN groups potentially result in acceptable color matching with 95% CIs. [ABSTRACT FROM AUTHOR]

Surface contaminants on customized implant abutments could trigger an inflammatory response in the peri-implant tissues. The aim of this randomized controlled study was to assess the radiographic bone changes around implants restored with customized, platform-switched abutments, with and without autoclave treatment, 12 months after definitive restoration. Dental implants were placed 1 mm subcrestally in 64 systemically healthy patients (mean age: 63.3 ± 10.0 years; 31 patients had a history of periodontitis) to replace single or multiple missing teeth. According to a randomization list, abutments were subjected to steam and autoclave sterilization (43 implants, test group) or steam cleaning alone (44 implants, control group). Periapical standardized radiographs were taken at implant placement, prosthetic abutment connection, and 12 months after definitive cement-retained restoration. All implants were clinically stable without any sign of infection at the 12-month follow-up. An average marginal bone loss of 0.25 ± 0.19 mm was found in the test group compared to 0.35 ± 0.23 mm in the control group (no statistically significant difference), while the percentage of bleeding sites was significantly higher in the control group (8.7% ± 13.1% vs 19.1% ± 19.8%; P = .035). Autoclave treatment of customized abutments seems to reduce the inflammatory response around subcrestally placed implants. [ABSTRACT FROM AUTHOR]

Purpose: To investigate the screw loosening and fracture resistance of different hybrid abutment crown restorations after thermomechanical aging. Materials and Methods: Restorations were produced from zirconia, lithium disilicate, and hybrid ceramics with a CAD/CAM system (n = 10). Restorations and titanium bases (Ti-bases) were cemented, and the abutment screws were torqued to 30 Ncm. They were retorqued after 10 minutes, and then the removal torque values (RTVs) were measured. After 250,000 and 500,000 cycles of thermomechanical aging were completed, the RTVs were measured again, and removal torque loss (RTL) ratios were calculated. The specimens were subjected to a fracture resistance test after 750,000 cycles of thermomechanical aging, and the load at failure was recorded as the fracture resistance (N). The results were statistically analyzed (a = .05). Results: Aging was effective on the RTVs and RTL ratios (P < .001). The highest RTV was observed before aging; however, the RTVs significantly decreased and RTL ratios significantly increased after aging (P < .05). The fracture resistance values significantly differed among the ceramic materials. All lithium disilicate and hybrid ceramic specimens showed restoration fracture and most of the zirconia specimens showed Ti-base-related failure. Conclusions: Hybrid abutment crowns made of zirconia, lithium disilicate, and hybrid ceramics can withstand the average occlusal forces in the molar region; however, the ceramic type may affect the failure type. Retightening of the abutment screws after 10 minutes following the first tightening and annually may be beneficial to prevent the adverse effects of screw loosening on the integrity of the implant-abutment connection. [ABSTRACT FROM AUTHOR]

Purpose: To investigate how well an implant stability quotient (ISQ) represents resonance frequency. Materials and Methods: Benchtop experiments on standardized samples that replicated a mandibular premolar site were conducted to correlate an ISQ value and a resonance frequency to synthetic bone density and an incremental insertion torque; then, a frequency spectrum analysis was performed to check the validity of the resonance frequency analysis (RFA). Brånemark Mk III implants (4 × 11.5 mm; Nobel Biocare) were placed in Sawbones test models of five different densities (40, 30, 40/20, 20, and 15 PCF). An incremental insertion torque was recorded during implant placement. To perform stability measurements, the test models were partially clamped in a vise (unclamped volume: 10 × 20 × 34 mm). A MulTipeg (Integration Diagnostics) was attached to the implants, and a Penguin (Integration Diagnostics) RFA measured ISQ. Simultaneously, the MulTipeg motion was monitored via a laser Doppler vibrometer and processed by a spectrum analyzer to obtain the resonance frequency. Tightness of the clamp was adjusted to vary the resonance frequency. A statistical analysis produced a linear correlation coefficient (R) among the measured ISQ, resonance frequency, and incremental insertion torque. Results: The resonance frequency had high correlation to the incremental insertion torque (R = 0.978), confirming the validity of using RFA for this study. Measured ISQ data were scattered and had low correlation to the resonance frequency (R = 0.214) and the incremental insertion torque (R = 0.386). The spectrum analysis revealed the simultaneous presence of multiple resonance frequencies. Conclusions: For the designed benchtop tests, resonance frequency does indicate implant stability in view of Sawbones density and incremental insertion torque. However, ISQ measurements do not correlate to the resonance frequency and may not reflect the stability when multiple resonance frequencies are present simultaneously. [ABSTRACT FROM AUTHOR]

Purpose: To evaluate the dimensional accuracy of implant impressions obtained using five different tray types and two techniques. Materials and Methods: A partially dentate maxillary Kennedy Class II model was created as a reference model through 3D printing. Then, implant analogs 4.3 mm in diameter were placed at the first premolar, first molar, and second molar sites. Five types of trays were used to create impressions: (1) metal stock trays, (2) plastic stock trays, (3) custom trays fabricated using liquid crystal display (LCD), (4) custom trays fabricated using fused deposition modeling (FDM), and (5) custom trays fabricated using urethane dimethacrylate (UDMA) resin. Open and closed tray techniques were also compared. In total, 150 impressions were obtained. The reference model and impressions were scanned using a laboratory scanner. Additionally, the positional and angular deviations of implants with different tray types and techniques were evaluated using the superimposition method. Results: There was no statistically significant difference (P > .05) between the impression accuracy with the different tray types and impression techniques. The angular deviations with plastic and UDMA trays were greater than those with metal, FDM, and LCD trays. Angular deviation at the second molar was greater when using closed plastic trays compared to open plastic trays. The highest and lowest positional deviations were observed at the first molar implant with an open plastic tray impression (mean ± SD of 62.46 ± 28.54 mm) and a closed LCD tray impression (36.59 ± 29.93 mm). The greatest angular deviation was observed with an open FDM tray impression at the first premolar implant (0.067 ± 0.024 degree), and the lowest angular deviation was observed with a closed metal stock tray impression at the second molar implant (0.039 ± 0.025 degree). Statistical differences were detected using the Mann-Whitney U test for paired groups and the Kruskal-Wallis test for groups with more than three comparisons (P > .05). Conclusions: Plastic and metal stock trays or conventional and 3D-printed custom trays can be used to obtain implant impressions for maxillary partially edentulous arches with similar dimensional accuracy. The five tray types and two techniques may be safely used to obtain impressions of partially edentulous maxillary arches with three implants. [ABSTRACT FROM AUTHOR]

The article discusses studies which show that full-ceramic prosthetic restorations for single crowns (SCs) and fixed dental prostheses (FDPs) are high quality and have a satisfactory survival rate comparable to porcelain-fused-to-metal (PFM). These studies include the survival outcome and complications in a retrospective clinical study of complete-arch fixed implant-supported prostheses (CAFIPs), the prevalence of prosthetic complications, and clinical performance of implant-supported FDPs.

Purpose: To measure the surface temperature distribution after using a CO2 laser to heat titanium dental implants via different power settings, application intervals, and irradiation times. Materials and Methods: A total of 10 tissue-level titanium implants (Screw-Line Promote Plus, Camlog; 4.3 × 11 mm) were placed (EpoFix, Struers) and irradiated with a CO2 laser (Denta 2, Lutronic) with a wavelength of 10.6 µm at power levels of 4 watts (Group 1), 6 watts (Group 2), 8 watts (Group 3), and 10 watts (Group 4). A continuous beam mode (setting I) and noncontinuous beam modes with 5-second (setting II) and 10-second (setting III) pause intervals were used. For each setting, a total irradiation time of 50 seconds was used and repeated 10 times. The temperature was measured using external thermocouple (Testo) in contact with the implant surface at the implant shoulder, middle, and apex. A linear regression model was used to analyze the data (P = .05). Results: Setting I demonstrated the most rapid increase in implant surface temperature in all three test sites as well as the greatest total temperature at 50 seconds of irradiation time. The greater the pause interval (settings II and III) during the 50 seconds of irradiation, the lower the rate of temperature increase as well as the total temperature in all three test sites and with all power levels. The average temperature difference between the apex and shoulder site was significant for setting III for all groups, but not for any groups in settings I and II. Conclusions: Heating the internal aspect of an implant with a CO2 laser produces different temperature distribution profiles depending on the laser power level and the application interval. Laser-beam irradiation leads to a temperature gradient, which is greatest at the implant apex and smallest at the implant shoulder. [ABSTRACT FROM AUTHOR]

Purpose: To compare the effect of taper, length, angle, and number of vertical axial walls on the retentive strength of a cemented crown on a partially customized hybrid abutment in the esthetic zone. Materials and Methods: A total of 35 metal copings were used and divided into two groups. One group had 30 copings cemented to their corresponding 8-degree tapered abutment with lengths from 3 to 8 mm, increasing in 1-mm increments (5 copings per length). The other group had the remaining 5 copings and consisted of a standardized metal coping that matched a hexagonal abutment with 3-mm vertical axial walls and the sequential removal of 1, 2, and 3 contiguous vertical axial walls. Dislodgment tests were performed for all copings in both groups. Maximum retentive forces were measured in retentive strength (kgF), with a conversion factor of 9.807 N = 1 kgF. Results: At each tapered abutment length, the retentive strength increased proportionally and was significantly different, ranging from 31.67 ± 4.10 kgF to 67.68 ± 11.22 kgF (F [5,24] = 20.46, P < .001). An unmodified hexagonal abutment demonstrated the highest retentive strength (70.15 ± 12.97 kgF). The sequential removal of 1, 2, and 3 contiguous vertical axial walls of the hexagonal abutment resulted in retentive strength values of 59.89 ± 10.06 kgF, 57.01 ± 9.62 kgF, and 55.99 ± 9.35 kgF, respectively, with no significant difference (P > .05) in strength. Conclusions: A partially customized abutment with vertical axial walls on one side and a profile reduction on the opposite side can provide comparable retention to cemented copings at one-third the length and at one-sixth the surface area of an 8-mm abutment with an 8-degree taper. [ABSTRACT FROM AUTHOR]

Background: Platelet-rich fibrin (PRF) is used to prepare "sticky bone" by combining it with bone graft material. The present study investigated the ability of different bone grafts to absorb growth factors from the PRF and release them over time. Materials and Methods: Human blood was collected from 10 healthy volunteers for liquid PRF preparation. Bovine bone, allograft (mineralized and demineralized), and synthetic bone were each mixed with the PRF to prepare a sticky bone. All sticky bone samples were incubated for up to 4 days. The absorption and release pattern kinetics of two selective growth factors within the PRF--platelet-derived growth factor (PDGF) and bone morphogenetic protein-2 (BMP-2)--were quantified with immunofluorescence staining and enzyme-linked immunoassay (ELISA) testing. Results: All bone graft materials adsorbed the examined growth factors from the PRF. ß-TCP showed the highest adsorption levels, followed by the xenograft, and the allografts showed the lowest adsorption levels. Furthermore, PDGF showed a fast-release pattern from the grafts, whereas BMP-2 was released at a later stage. Similar to the adsorption pattern, the ß-TCP and xenograft were better able to sustain the release of the PRF growth factors from the graft than the allografts. Conclusions: The adsorption of PDGF and BMP-2 differ between graft materials, with superior results for ß-TCP, followed by xenograft, then allograft materials. [ABSTRACT FROM AUTHOR]

This clinical case outlines a comprehensive digital workflow for a minimally invasive multidisciplinary treatment. The process utilizes one open-source software for digital wax-up and one low-cost software to address esthetic concerns related to teeth misalignment. The patient's function was stabilized with a digitally made occlusal splint. The application of the described digital workflow technique, incorporating open-source, lowcost, and closed software, played a pivotal role in attaining a straightforward and predictable outcome with minimally invasive treatment. Furthermore, the continual evolution of technology contributes to the growing precision of dental procedures. The presented digital workflow helped formulate a predictable treatment plan, replicate a diagnostic digital wax-up, and achieve precise teeth alignment. This approach satisfactorily addressed the patient's esthetic concerns, providing an outstanding approximation of the definitive result. [ABSTRACT FROM AUTHOR]

Objectives: The objective was to evaluate the polymerization efficiency of different bulk-fill resin-based composites cured by monowave and polywave light-curing units, by assessment of the degree of conversion and Vickers microhardness at different depths. Method and materials: Two commercially available bulk-fill resin-based composites were used: Filtek One Bulk Fill Restorative (3M ESPE) and Tetric N-Ceram Bulk Fill (Ivoclar Vivadent). The light-curing units utilized were two LED light-curing units: a monowave LED light-curing unit (BlueLEX LD-105, Monitex) and a polywave LED light-curing unit (Twin Wave GT-2000, Monitex). For each test, 20 cylindrical specimens (4 mm diameter, 4 mm thickness) were prepared from each bulk-fill resin-based composite using a split Teflon mold. Ten specimens were light-cured by the monowave light-curing unit and the other ten were light-cured by the polywave light-curing unit according to the manufacturer's recommendations. Attenuated total reflectance-Fourier transform infrared spectroscopy (ATRFTIR) was used to assess the degree of conversion, and a Vickers microhardness tester was used to assess Vickers microhardness. Statistical analysis was performed using three-way ANOVA and Tukey post-hoc tests (P < .05). Results: The degree of conversion and Vickers microhardness in bulk-fill resin-based composites containing only camphorquinone as photoinitiator were similar when cured with either monowave or polywave light-curing units. However, bulk-fill resin-based composites containing a combination of photoinitiators exhibited significantly higher degree of conversion and Vickers microhardness when cured with a polywave light-curing unit. Although all groups showed statistically significant differences between the top and bottom surfaces regarding degree of conversion and Vickers microhardness, all of them showed bottom/top ratios > 80% regarding degree of conversion and Vickers microhardness. Conclusion: The polywave light-curing unit enhanced the polymerization efficiency of bulk-fill resin-based composites especially when the latter contained a combination of photoinitiators, but does not prevent the use of a monowave light-curing unit. [ABSTRACT FROM AUTHOR]

This study aimed to evaluate the periodontal responses of subgingival proximal margins elevated using different restorative materials. A total of 120 proximal cavities with dentin/cementum gingival margins were elevated using one of four materials (resin-modified glass ionomer, glass hybrid, flowable bulk-fill resin composite, or bioactive ionic resin) and completed with the same overlaying resin composite. At 2 weeks (baseline), 6 months, 1 year, and 2 years postrestoration, periodontal parameters and the radiographic distance between the restoration margin and bone crest were evaluated. Appropriate statistical analyses were performed. The values of all periodontal parameters increased with time, although only the increases in Plaque Index and probing depth within each material group were statistically significant. There were no statistically significant differences in any of the periodontal parameters between the different materials within the same evaluation period, nor between different time points or material groups in the radiographic distances. Both glass ionomer--based and resin-based materials were periodontally safe as subgingival open sandwich restorations. [ABSTRACT FROM AUTHOR]

This canine in vivo study assessed the effect of recombinant human platelet-derived growth factor (rhPDGF) on the healing of periapical tissues following apical surgery. From a total of 96 premolar teeth, 64 teeth from six beagle dogs (2 years old) were classified as experimental and were randomly assigned to four experimental groups (16 teeth per group). After having the pulp extirpated, leaving teeth open to the oral cavity for 1 week, and sealing with an immediate restorative material for 8 weeks, nonsurgical endodontic treatment was performed. A split-mouth design was used, and intra-animal randomization of treatment sides was applied to the groups as follows: apical curettage + 1.5-mm root-end resection (Group 1); apicoectomy + mineral trioxide aggregate (MTA) root-end filling (Group 2); apicoectomy + MTA root-end filling + rhPDGF (Group 3); and apical curettage + rhPDGF (Group 4). The animals were sacrificed 24 months after apical surgery, and histologic and µCT analyses were performed for bone volume loss (BVL). Group 1 showed partial resolution of the periapical lesions without signs of tissue regeneration (BVL: 49.09 ± 10.97 mm3). Group 2 had minimal bone regeneration and showed cementum reformation in 9 teeth, with no direct attachment to the MTA (BVL: 35.34 ± 10.97 mm3). Group 3 showed regeneration of all damaged apical tissues without direct contact between the cementum and MTA (BLV: 4.51 ± 1.55 mm3). Group 4 showed regeneration of PDL, bone, and cementum and attachment of functional cementum fibers (BVL: 2.82 ± 2.3 mm3). The difference in BVL was statistically significant only for Groups 1 and 2 (P < .05). rhPDGF may help regenerate apical tissue structures following apical surgery. [ABSTRACT FROM AUTHOR]

Purpose: To analyze the effectiveness of coating of abutments with antimicrobial agents and their influence on the physicochemical and biologic properties of the coated materials. Materials and Methods: This work was registered in Open Science Framework (osf.io/6tkcp) and followed the PRISMA protocols. A search of two independent reviewers of articles published up to October 29, 2021, was performed in the Embase, PubMed, Science Direct, and Scopus databases. Results: The databases found a total of 1,474 references. After excluding the duplicates, 1,050 remained. After reading the titles and abstracts and applying the inclusion criteria, 13 articles remained and were read in full. A total of 8 articles were included in this systematic review. Different antimicrobial agents have been used to coat abutments, including graphene oxide, polydopamine, titanium and zirconium nitride, lactoferrin, tetracycline, silver, and doxycycline with varied release times. Titanium-coated silver showed a better antimicrobial agent release time of up to 28 days. Chemical analysis confirmed the presence of antimicrobials on the surface after coating. Different pathogenic microorganisms, such as Streptococcus sanguinis, Streptococcus oralis, and Staphylococcus aureus, were inhibited when in contact with the coated surface. Conclusions: This review showed that there is still no consensus on which is the better antimicrobial agent and which coated materials have the better performance. However, the association of surface coating of abutments with antimicrobials is feasible and can benefit many patients, which can support their clinical use to favor the healing process and prevent infections that can lead to treatment failure with dental implants. [ABSTRACT FROM AUTHOR]

Objectives: To compare marginal gap width and depth with different cementation systems, excess removal, and after polishing. Method and materials: In total, 80 composite crowns were milled, divided into ten groups, and cemented on identical artificial teeth. Eight crowns per group were fixed with (i) zinc phosphate cement (ZnOPh), (ii) glass-ionomer cement (GIC), (iii) resin-reinforced glass-ionomer cement (GIC mod), (iv) dual-curing adhesive composite (Comp dual), or (v) dual-curing self-adhesive composite (Comp SE dual). Excess removal was performed with a scaler after brief light-cure (tack-cure), final light-cure, during rubber or gel phase or by wiping with foam pellet. Curing was completed in chemical, dark cure, or light-curing modus. The specimens were polished and stored in water (37°C). The margins were digitized using a 3D laser-scanning microscope (VK-X100 series, Keyence). The width and the depth of the marginal gap were measured at 10 points between the crown margin and the preparation margin. Results: The width after excess removal varied between 65.1 ± 15.7 µm (Comp dual, wipe, with polishing) and 208.6 ± 266.7 µm (Comp SE dual, dark cure, without polishing). The depth varied between 29.8 ± 22.2 µm (Comp dual, wipe, with polishing) and 89.5 ± 45.2 µm (Comp SE dual, dark cure, without polishing). The impact on gap width and depth was detected for fixation material, excess removal, and polishing. Conclusion: The gap depth and width depend on the luting material and the mode of access removal. Polishing can improve the gap quality, especially for GIC and resin-based systems. [ABSTRACT FROM AUTHOR]

Objectives: To evaluate the effect of sonic oscillation on penetration depth and marginal adaptation of resin-based fissure sealants. Method and materials: Thirty-six extracted human third molars were randomized into three groups: in the HF group, teeth were sealed with a filled-resin-based sealant (Helioseal F); in the Sonic-HF group, teeth were sealed with Helioseal F and subjected to sonic oscillation (Compothixo Device, 140 Hz vibration frequency and ± 150 µm amplitude) before curing; in the CO group, teeth were sealed with an unfilled-resin-based sealant (Clinpro). All teeth were thermocycled for 1,500 cycles at 5°C and 55°C, then sectioned buccolingually into four sections (mesial, two middle, and distal). Sections were evaluated under SEM for marginal adaptation and scored. For penetration depth, three independent measurements from each tooth were recorded under SEM, and data were subjected to statistical analysis. Results: The group subjected to sonic oscillation (Sonic HF) resulted in significantly superior penetration depth and marginal adaptation compared with the HF group, but with no significant difference compared with the CO group. Conclusions: Sonic activation of resin-based sealant increased penetration depth into fissures and marginal adaptation to the enamel wall without decreasing filler load or compromising sealant mechanical properties. [ABSTRACT FROM AUTHOR]

The article discusses the innovative use of additive manufacturing technology for creating lithium disilicate ceramic restorations in dentistry. Traditionally, these restorations were made using analog pressing or subtractive milling techniques. The article presents a case study demonstrating the feasibility of 3D printing lithium disilicate crowns for natural teeth and implants, comparing the results with subtractive fabrication. The study highlights the potential benefits of additive manufacturing, such as improved precision and cost-effectiveness, while emphasizing the need for further research and optimization of the technology. [Extracted from the article]

The article "Replacement of Failing Restorations in the Esthetic Zone: Solutions to Clinical and Laboratory Challenges" discusses the challenges and solutions involved in replacing failing indirect ceramic restorations in the esthetic zone. The text emphasizes the importance of preserving healthy tooth structure and following detailed treatment plans to achieve successful outcomes. It also highlights the use of modern technologies, such as digital impressions and cloud-based communication, to streamline the workflow between clinicians and laboratory technicians. [Extracted from the article]

The article discusses a case report on a digital and interdisciplinary adhesive conservative rehabilitation approach for a young patient with dental structure loss. The treatment focuses on integrating esthetic and occlusal parameters using restorative materials and digital tools. The interdisciplinary approach involves restorative dentistry, orthodontics, and prosthodontics to achieve a successful outcome. The treatment plan includes periodontal therapy, nonanatomical biologic reconstruction, clear aligner therapy, and sectorized ceramic restorations. The article emphasizes the importance of a smooth integration between esthetic and occlusal parameters in conservative oral rehabilitation. [Extracted from the article]

Purpose: To investigate the effect of adhesive type and long-term aging on the shear bond strength (SBS) between silicabased ceramics and composite cement (CC). Materials and Methods: Lithium-silicate (LS), feldspathic (FD) and polymer-infiltrated ceramic (PIC) blocks were sectioned (10 x 12 x 2 mm) and divided into 24 groups considering the factors: "ceramics" (LS, FD, and PIC), "adhesive" (Ctrl: without adhesive; 2SC: 2-step conventional; 3SC: 3-step conventional; 1SU: 1-step universal), and "aging" (non-aged or aged [A]). After the surface treatments, CC cylinders (n = 15, ɸ=2mm; height = 2mm) were made and half of the samples were subjected to thermocycling (10,000) and stored in water at 37°C for 18months. The samples were submitted to SBS testing (100 kgf, 1mm/min) and failure analysis. Extra samples were prepared for microscopic analysis of the adhesive interface. SBS (MPa) data was analyzed by 3-way ANOVA and Tukey's test (5%). Weibull analysis was performed on the SBS data. Results: All factors and interactions were significant for SBS (p<0.05). Before aging, there was no significant difference between the tested groups and the respective control groups. After aging, the LS_1SU (22.18±7.74) and LS_2SC (17.32±5.86) groups exhibited significantly lower SBS than did the LS_Ctrl (30.30±6.11). Only the LS_1SU group showed a significant decrease in SBS after aging vs without aging. The LS_1SU (12.20) group showed the highest Weibull modulus, which was significantly higher than LS_2SC_A (2.82) and LS_1SU_A (3.15) groups. Conclusion: No type of adhesive applied after silane benefitted the long-term adhesion of silica-based ceramics to CC in comparison to the groups without adhesive. [ABSTRACT FROM AUTHOR]

Purpose: The study evaluated the clinical performance of partial indirect resin composite (PIRC) restorations with "proximal box elevation" (PBE) placed in molars. Materials and Methods: Sixty-three patients received 80 posterior PIRC (SR Nexco, Ivoclar Vivadent) restorations. Large posterior defects with cuspal loss and deep cervical margins were included in the study. PBE was performed priorto preparation and impression making. Two independent observers evaluated the restorations using the FDI criteria (scores 1-5) foresthetic, functional, and biological properties. Patients were recalled at 6 months and 1, 2, and 3 years. Overall success rates were calculated (Kaplan-Meier analysis) and compared (log-rank tests) according to baseline variables. The impact of the baseline variables on the failure of the restorations was analyzed (multiple proportional Cox regression). Results: Seventy-nine (98.7%), 69 (88.4%), 66 (92.9%), 44 (86.2%) and 45 (91.8%) PIRCs completed their follow up at baseline, 6 months, and 1, 2 and 3 years, respectively. In total, 10 failures were observed: 5 with partial loss, 4 with material chipping, and one with secondary caries, yielding an overall success rate of 87.5% and a survival rate of 93.8%, with a mean observation timeof 26.5 ± 13.6 months. Conclusions: PIRCs with PBE demonstrated a high survival rate and satisfactory esthetic properties. Failure was less likelyfor PIRC restorations with partial cuspal coverage (onlay) compared to full cuspal coverage (overlay). [ABSTRACT FROM AUTHOR]

Background: This systematic review with meta-analysis aimed to evaluate if the incorporation of metallic nanoparticles (NPs) in dental materials present antimicrobial effects without prejudice to physical and mechanical properties. Material and methods: After PROSPERO registration (CRD42022297684), Medline via Pubmed, Scopus, Web of Science, EBSCO, LILACS, LIVIO, Embase and grey literature such as Google Scholar, ProQuest and OpenGrey, were searched until June 26th, 2024. Meta-analysis of materials incorporated with metallic nanoparticles was performed for antimicrobial action (standardized mean differences) and mechanical properties (mean differences) through inverse variance and randomized effects (Revman, p < 0.05). Results: For risk of bias, studies were evaluated according to the Joanna Briggs Institute's critical assessment. Forty-four out of the 3818 articles initially identified were eligible for the review, and 30 were included in the meta-analysis. Meta-analysis pointed out that the incorporation of silver and copper presented antimicrobial activity, reducing colony forming units (CFU) when incorporated in primer and glass ionomer cement (GIC). Silver increased inhibition zones and reduced cell viability through live dead cell viability assay in primer, GIC and adhesives. Silver incorporation reduced microhardness and shear strength of adhesives and increased compressive strength of GIC and shear strength of primer. Conclusions: The incorporation of metallic nanoparticles, especially silver copper and titanium presented benefits to antimicrobial properties compared with the original unmodified materials. However, some mechanical properties of restorative dental materials were damaged. In contrast to some studies in the literature that evaluated metallic nanoparticles, our findings indicate negative effects on properties. Article highlights: Ag was incorporated into a primer with a significant CFU-count reduction. Incorporation of AgNPs in GIC, primer, adhesive, resin reduced CFU. Risk of bias more associated with lack of blinding of control and treatment groups. The Cu incorporation significantly reduced CFU counts (GIC, adhesive). The AgNPs significantly reduced shear strength (adhesive/primer). AgNPs incorporation negatively interfered for microhardness adhesives. [ABSTRACT FROM AUTHOR]

Background: This study investigated the practices and opinions of Turkish dentists regarding the management of deep caries lesions using an online questionnaire. Methods: The questionnaire had two sections: the first collected demographic data, while the second focused on clinical practices, including radiographic techniques, rubber dam usage, liner choices, pulp protection, and post-endodontic restoration methods. Results: The survey response rate was 20.4%. 18 participants were excluded due to incomplete responses in the survey. A total of 390 survey texts (19.5%) were analyzed. The gender distribution of the participants was as follows: 60% female and 40% male. Notably, none of the respondents used rubber dams for endodontic treatment. Male dentists were less likely to use a base under restorations (p < 0.05). Female dentists preferred single-session pulp capping for pulpal perforations (p < 0.05). Public hospitals utilized fewer panoramic films, while Oral and Dental Health Centers used fewer periapical films for diagnoses (p < 0.05). Glass ionomer cement was the most commonly used base material, and direct composite resin was the preferred choice for post-endodontic restorations, in contrast to the less favored indirect composite resin. Conclusions: Despite its advantages, the application of rubber dam was infrequent. Glass ionomer cement emerged as the predominant base material across all restoration types, exhibiting variability among dentists in diagnosis, treatment, and material selection. [ABSTRACT FROM AUTHOR]

The objective of this study was to investigate the antimicrobial potential of glass ionomer cement (GIC) incorporated with silver and copper nanoparticles (CuAgNP) in three different concentrations (GIC 0.01% CuAgNP, GIC 0.05% CuAgNP, and GIC 0.1% CuAgNP) on the inhibition of in vitro formation of duospecies biofilm of Streptococcus mutans and Candida albicans, surface roughness, color variation, and curing time. A control group was also included, consisting of GIC without nanoparticles. Duoespecie biofilms were grown on specimens of GIC in Tryptic Soy Broth placed in 24-well plates for 72 h. The biofilms were then collected and plated on Mitis-Salivarius-Bacitracin (MSB) agar and Sabouraud dextrose agar for Streptococcus mutans and Candida albicans, respectively. Colony-forming unit (CFU) counts and dry weight were measured to assess the biofilm growth. Physical properties were evaluated through tests on surface roughness, color variation, and curing time. The normality of the distribution was evaluated using the Kolmogorov–Smirnov test. Data were analyzed using ANOVA followed by Tukey's test. The results showed that the addition of CuAgNP did not increase antimicrobial activity compared to the control (p > 0.05). Furthermore, longer curing time resulted in negative effects on physical properties, such as color variation and greater surface roughness (p < 0.05). The addition of CuAgNP did not improve the properties of GIC in this study. [ABSTRACT FROM AUTHOR]

Background: The aim of this review is to compare the clinical outcomes of different soft tissue grafting materials (connective tissue graft (CTG), platelet-rich fibrin (L-PRF), allogenic and xenogenic substitutes) applied in immediate implant placement with each other. Methods: Through an electronic search regarding the study's main question ("In patients with non-restorable teeth, who receive immediate dental implants (P), what is the best adjunctive soft tissue grafting approach among different autogenous, allogenous, and xenogenous grafts (I), to achieve the desired hard and soft tissue structure (O), compared to sites without grafting (C)?") in PubMed, Scopus, and ISI Web of Science, randomized controlled clinical trials (RCTs) using different soft tissue grafts were identified and analyzed using a Bayesian random-effect network meta-analysis framework. The pink esthetic score (PES), marginal interproximal bone level changes (MIBL), buccal bone thickness changes (BBT), keratinized tissue width changes (KTW), soft tissue thickness changes (STT), papilla height changes (PH), midfacial gingival margin level changes (MGML) were defined as desired outcomes of the study; except for the MIBL with 12 – 24 months of follow-up, 6 – 12 months is considered for other outcomes. Results: After duplication removal, 903 studies were identified through the electronic search; from which 21 RCTs were included in the review. Among all comparisons in different outcomes, only CTG demonstrated a significantly higher gain in STT compared to not placing soft tissue graft. However, CTG in MIBL, KTW, STT, PH, and MGML, and uni-layer xenogenic collagen matrix in PES were the superior treatments, according to the treatment ranking based on surface under cumulative ranking (SUCRA). Conclusions: At the time of immediate implantation, there is no significant difference between different soft tissue grafts regarding the clinical outcomes of implants. However, the utilization of CTG can be suggested in cases with thin soft tissue. The acceptable efficacy of allogenic and xenogenic materials and the non-significant difference between them and CTG indicate supporting evidence for the application of these materials to specific clinical situations simultaneously with immediate implantation. Systematic review registration: CRD42024568586. [ABSTRACT FROM AUTHOR]

Additive manufacturing (3D printing) has transformed dentistry by providing solutions with high precision and accuracy achieved through digital workflows, which facilitate the creation of intricate and personalized structures. Additionally, 3D printing promotes cost efficiency by reducing material waste and errors while enabling on-demand production, minimizing the need for extensive inventories. Recent advancements in 3D-printed resin materials have enhanced their clinical applications by improving mechanical strength, biocompatibility, esthetics, and durability. These innovations have facilitated the fabrication of complex and patient-specific structures, such as dental prostheses, surgical guides, and orthodontic appliances, while significantly reducing production time and material waste. Ongoing research and innovation are expected to strengthen resin properties, including strength, translucency, and durability, broadening their clinical applications. The ongoing evolution of 3D printing technology is poised to play a critical role in driving personalized treatments, streamlining clinical workflows, and shaping the future of dental care. This narrative review comprehensively examines the production techniques and clinical applications of 3D-printed photopolymer resins across various dental specialties, including prosthodontics, orthodontics, pediatric dentistry, maxillofacial surgery, periodontology, endodontics, and conservative dentistry. Additionally, the review provides insight into the transformative impact of these technologies on patient care, highlights existing challenges, and suggests future directions for advancing resin properties and their integration into routine dental practice. [ABSTRACT FROM AUTHOR]