Search

In this paper, numerical simulations of particle migration in lubricating grease flow are presented. The rheology of three lithium greases with NLGI (National Lubricating Grease Institute) grades 00, 1 and 2 respectively are considered. The grease is modeled as a single-phase Herschel-Bulkley fluid, and the particle migration has been considered in two different grease pockets formed between two concentric cylinders where the inner cylinder is rotating and driving the flow. In the wide grease pocket, the width of the gap is much smaller compared to the axial length scale, enabling a one-dimensional flow. In the narrow pocket, the axial and radial length is of the same order, yielding a three-dimensional flow. It was found that the change in flow characteristics due to the influence of the pocket lateral boundaries when going from the wide to the narrow pocket leads to a significantly shorter migration time. Comparing the results with an existing migration model treating the radial component contribution, it was concluded that a solution to the flow in the whole domain is needed together with a higher order numerical scheme to obtain a full solution to the particle migration. This result is more pronounced in the narrow pocket due to gradients in the flow induced by the lateral boundaries. [ABSTRACT FROM AUTHOR]

In this paper, numerical simulations of lubricating grease flow in the grease pocket of a double restriction seal geometry using computational fluid dynamics are presented. The grease is treated as a single-phase Herschel-Bulkley fluid with different rheological properties corresponding to NLGI grade 00, 1 and 2. The numerical code and rheology model have been validated with a semi-analytical solution based on flow measurements using microparticle image velocimetry. The flow has been modelled for low and high rotational speeds driving the flow, and elevated temperatures. Also, the evolution of contaminant particles in the grease pocket is investigated. It was found that the flow and velocity distribution in the pocket-and consequently the contaminant particle concentration evolution, is characterized by the shear thinning rheology of the grease. With higher shear rates in the grease and higher temperatures, the grease approaches a more Newtonian type of behaviour leading to a reduced yield and shear thinning characteristics directly affecting the grease ability to transport contaminant particles. [ABSTRACT FROM AUTHOR]

In this paper, numerical simulations of particle migration in lubricating grease flow are presented. The rheology of three lithium greases with NLGI (National Lubricating Grease Institute) grades 00, 1 and 2 respectively are considered. The grease is modeled as a single-phase Herschel–Bulkley fluid, and the particle migration has been considered in two different grease pockets formed between two concentric cylinders where the inner cylinder is rotating and driving the flow. In the wide grease pocket, the width of the gap is much smaller compared to the axial length scale, enabling a one-dimensional flow. In the narrow pocket, the axial and radial length is of the same order, yielding a three-dimensional flow. It was found that the change in flow characteristics due to the influence of the pocket lateral boundaries when going from the wide to the narrow pocket leads to a significantly shorter migration time. Comparing the results with an existing migration model treating the radial component contribution, it was concluded that a solution to the flow in the whole domain is needed together with a higher order numerical scheme to obtain a full solution to the particle migration. This result is more pronounced in the narrow pocket due to gradients in the flow induced by the lateral boundaries.

Microparticle image velocimetry (μPIV) is used to measure the grease velocity profile in small seal-like geometries and the radial migration of contaminant particles is predicted. In the first part, the influence of shaft speed, grease type, and temperatures on the flow of lubricating greases in a narrow double restriction sealing pocket is evaluated. Such geometries can be found in, for example, labyrinth-type seals. In a wide pocket the velocity profile is one-dimensional and the Herschel-Bulkley model is used. In a narrow pocket, it is shown by the experimental results that the side walls have a significant influence on the grease flow, implying that the grease velocity profile is two-dimensional. In this area, a single empirical grease parameter for the rheology is sufficient to describe the velocity profile. In the second part, the radial migration of contaminant particles through the grease is evaluated. Centrifugal forces acting on a solid spherical particle are calculated from the grease velocity profile. Consequently, particles migrate to a larger radius and finally settle when the grease viscosity becomes large due to the low shear rate. This behavior is important for the sealing function of the grease in the pocket and relubrication. [ABSTRACT FROM AUTHOR]