Search

The application of the Coandă effect to the directional control of a jet or thrust is presented. Deviation of the thrust force by direct flow can be achieved by using the Coandă effect to change the angle of the primary jet engine exhaust nozzle. Major interest in the study of this phenomenon is caused by the possibility of using this effect for aircrafts with short take-off and landing, for thrust vectoring. The numerical investigations are performed using a RANS solver with an adequate turbulence model, showing a change of the jet direction. Thus, the conditions and the limits within which one can benefit from the advantages of Coandă-type flows are determined. [ABSTRACT FROM AUTHOR]

Transgenic Panicum virgatum L. silencing ( KD) or overexpressing ( OE) specific genes or a small RNA ( GAUT4- KD, mi RNA156- OE, MYB4- OE, COMT- KD and FPGS- KD) was grown in the field and aerial tissue analysed for biofuel production traits. Clones representing independent transgenic lines were established and senesced tissue was sampled after year 1 and 2 growth cycles. Biomass was analysed for wall sugars, recalcitrance to enzymatic digestibility and biofuel production using separate hydrolysis and fermentation. No correlation was found between plant carbohydrate content and biofuel production pointing to overriding structural and compositional elements that influence recalcitrance. Biomass yields were greater for all lines in the second year as plants establish in the field and standard amounts of biomass analysed from each line had more glucan, xylan and less ethanol (g/g basis) in the second- versus the first-year samples, pointing to a broad increase in tissue recalcitrance after regrowth from the perennial root. However, biomass from second-year growth of transgenics targeted for wall modification, GAUT4- KD, MYB4- OE, COMT- KD and FPGS- KD, had increased carbohydrate and ethanol yields (up to 12% and 21%, respectively) compared with control samples. The parental plant lines were found to have a significant impact on recalcitrance which can be exploited in future strategies. This summarizes progress towards generating next-generation bio-feedstocks with improved properties for microbial and enzymatic deconstruction, while providing a comprehensive quantitative analysis for the bioconversion of multiple plant lines in five transgenic strategies. [ABSTRACT FROM AUTHOR]

Biorefining of plant feedstocks into fuels and specialty chemicals, using biological conversion, requires the solubilization of lignocellulosics into simpler oligomeric compounds. However, non-pretreated woody biomass has shown high resistance to hydrolysis by cellulolytic microbes or purified cellulases. We investigate the limited solubilization of Populus deltoides by the cellulolytic thermophile Clostridium thermocellum in the absence of solute inhibitors. Compared to control samples, fermented poplar revealed that the hydrolysis of carbohydrates in secondary cell walls ceased prematurely as the presence of lignin increased at the surface. In quantitative fluorescence colocalization analysis by confocal laser scanning microscopy, the Manders’ coefficient of the fractional overlap between lignin and cellulose signals increased from an average of 0.67 to a near-maximum of 0.92 in fermented tissue. Chemical imaging by time-of-flight secondary ion mass spectrometry revealed a 49% decline in surface cellulose and a compensatory 30% and 11% increase in surface S- and G-lignin, respectively. Although 72% of the initial glucan was still present in the lignocellulose matrix of this feedstock, subsequent treatments with cell-free purified cellulases did not significantly restore hydrolysis. This confirmed that biomass surfaces had become non-productive for the C. thermocellum hydrolytic exoproteome. This study provides direct evidence for an explicit definition of feedstock recalcitrance, whereby depletion of surface carbohydrate increases lignin exposure which leads to inhibition of enzyme activity, while the bulk residual biomass retains significant undigested carbohydrate content. The analysis presented here establishes a novel method for the quantitation of lignocellulose recalcitrance. [ABSTRACT FROM AUTHOR]

Background: Higher ratios of syringyl-to-guaiacyl (S/G) lignin components of Populus were shown to improve sugar release by enzymatic hydrolysis using commercial blends. Cellulolytic microbes are often robust biomass hydrolyzers and may offer cost advantages; however, it is unknown whether their activity can also be significantly influenced by the ratio of different monolignol types in Populus biomass. Hydrolysis and fermentation of autoclaved, but otherwise not pretreated Populus trichocarpa by Clostridium thermocellum ATCC 27405 was compared using feedstocks that had similar carbohydrate and total lignin contents but differed in S/G ratios. Results: Populus with an S/G ratio of 2.1 was converted more rapidly and to a greater extent compared to similar biomass that had a ratio of 1.2. For either microbes or commercial enzymes, an approximate 50 % relative difference in total solids solubilization was measured for both biomasses, which suggests that the differences and limitations in the microbial breakdown of lignocellulose may be largely from the enzymatic hydrolytic process. Surprisingly, the reduction in glucan content per gram solid in the residual microbially processed biomass was similar (17-18 %) irrespective of S/G ratio, pointing to a similar mechanism of solubilization that proceeded at different rates. Fermentation metabolome testing did not reveal the release of known biomass-derived alcohol and aldehyde inhibitors that could explain observed differences in microbial hydrolytic activity. Biomass-derived p-hydroxybenzoic acid was up to ninefold higher in low S/G ratio biomass fermentations, but was not found to be inhibitory in subsequent test fermentations. Cellulose crystallinity and degree of polymerization did not vary between Populus lines and had minor changes after fermentation. However, lignin molecular weights and cellulose accessibility determined by Simons' staining were positively correlated to the S/G content. Conclusions: Higher S/G ratios in Populus biomass lead to longer and more linear lignin chains and greater access to surface cellulosic content by microbe-bound enzymatic complexes. Substrate access limitation is suggested as a primary bottleneck in solubilization of minimally processed Populus, which has important implications for microbial deconstruction of lignocellulose biomass. Our findings will allow others to examine different Populus lines and to test if similar observations are possible for other plant species. [ABSTRACT FROM AUTHOR]

A mathematical model for the growth of thin Clostridium thermocellum biofilms on cellulose sheets with penetration from the surface into the interior fiber matrix is formulated, and used to assess the potential of CO 2 on-line measurements for activity of cellulolytic biofilms. The biofilm growth model is linked to a product formation model. It includes the processes of carbon substrate consumption, biofilm growth, biofilm upkeep, and carbon dioxide production. The mathematical description leads to a system of ordinary differential equations that is simple enough to lend itself to qualitative analysis, yet complex enough to capture the essential features of the system. Numerical fitting of the model against experimental data showed excellent quantitative agreement. The model substantiates the utility of on-line CO 2 measurements as indicator of cellulose substrate colonization and consumption, which may be useful for reporting bioreactor performance. [ABSTRACT FROM AUTHOR]

The goal of this paper is to provide a numerical flow analysis based on RANS equations in two directions: the study of augmented high-lift system for a cross-section airfoil of a wing up to transonic regime and the circulation control implemented by tangentially blowing jet over a highly curved surface due to Coanda effect on a rotor blade for a wind turbine. This study were analyzed the performance, sensitivities and limitations of the circulation control method based on blowing jet for a fixed wing as well as for a rotating wing. Directions of future research are identified and discussed. [ABSTRACT FROM AUTHOR]

The goal of this paper is to provide a numerical flow analysis based on RANS equations in two directions: the study of augmented high-lift system for a cross-section airfoil of a wing up to transonic regime and the circulation control implemented by tangentially blowing jet over a highly curved surface due to Coanda effect on a rotor blade for a wind turbine. This study were analyzed the performance, sensitivities and limitations of the circulation control method based on blowing jet for a fixed wing as well as for a rotating wing. Directions of future research are identified and discussed. [ABSTRACT FROM AUTHOR]

Background Microbial cellulose conversion by Clostridium thermocellum 27405 occurs predominantly through the activity of substrate-adherent bacteria organized in thin, primarily single cell-layered biofilms. The importance of cellulosic surface exposure to microbial hydrolysis has received little attention despite its implied impact on conversion kinetics. Results We showed the spatial heterogeneity of fiber distribution in pure cellulosic sheets, which made direct measurements of biofilm colonization and surface penetration impossible. Therefore, we utilized on-line measurements of carbon dioxide (CO2) production in continuous-flow reactors, in conjunction with confocal imaging, to observe patterns of biofilm invasion and to indirectly estimate microbial accessibility to the substrate's surface and the resulting limitations on conversion kinetics. A strong positive correlation was found between cellulose consumption and CO2 production (R2 = 0.996) and between surface area and maximum biofilm activity (R2 = 0.981). We observed an initial biofilm development rate (0.46 h-1, 0.34 h-1 and 0.33 h-1) on Whatman sheets (#1, #598 and #3, respectively) that stabilized when the accessible surface was maximally colonized. The results suggest that cellulose conversion kinetics is initially subject to a microbial limitation period where the substrate is in excess, followed by a substrate limitation period where cellular mass, in the form of biofilms, is not limiting. Accessible surface area acts as an important determinant of the respective lengths of these two distinct periods. At end-point fermentation, all sheets were digested predominantly under substrate accessibility limitations (e.g., up to 81% of total CO2 production for Whatman #1). Integration of CO2 production rates over time showed Whatman #3 underwent the fastest conversion efficiency under microbial limitation, suggestive of best biofilm penetration, while Whatman #1 exhibited the least recalcitrance and the faster degradation during the substrate limitation period. Conclusion The results showed that the specific biofilm development rate of cellulolytic bacteria such as C. thermocellum has a notable effect on overall reactor kinetics during the period of microbial limitation, when ca. 20% of cellulose conversion occurs. The study further demonstrated the utility of on-line CO2 measurements as a method to assess biofilm development and substrate digestibility pertaining to microbial solubilization of cellulose, which is relevant when considering feedstock pre-treatment options. [ABSTRACT FROM AUTHOR]

An obituary is presented for professor Mihai Popescu is presented.

The importance of bacterial adherence has been acknowledged in microbial lignocellulose conversion studies; however, few reports have described the function and structure of bioflims supported by cellulosic substrates. We investigated the organization, dynamic formation, and carbon flow associated with bioflims of the obligately anaerobic cellulolytic bacterium Clostridium thennocellum 27405. Using noninvasive, in situ fluorescence imaging, we showed biofilms capable of near complete substrate conversion with a characteristic monolayered cell structure without an extracellular polymeric matrix typically seen in biofilms. Cell division at the interface and terminal endospores appeared throughout all stages of bioflim growth. Using continuous-flow reactors with a rate of dilution (2 h-1) 12-fold higher than the bacterium's maximum growth rate, we compared biofllm activity under low (44 g/liter) and high (202 glliter) initial cellulose loading. The average hydrolysis rate was over 3-fold higher in the latter case, while the proportions of oligomeric cellulose hydrolysis products lost from the biofilm were 13.7% and 29.1% of the total substrate carbon hydrolyzed, respectively. Fermentative catabolism was comparable between the two cellulose loadings, with ca. 4% of metabolized sugar carbon being utilized for cell production, while 75.4% and 66.7% of the two cellulose loadings, respectively, were converted to primary carbon metabolites (ethanol, acetic acid, lactic acid, carbon dioxide). However, there was a notable difference in the ethanol-to-acetic acid ratio (gig), measured to be 0.91 for the low cellulose loading and 0.41 for the high cellulose loading. The results suggest that substrate availability for cell attachment rather than biofilm colonization rates govern the efficiency of cellulose conversion. [ABSTRACT FROM AUTHOR]

Abstract: This paper presents a NC toolpath generation strategy with tool engagement control for arbitrarily complex discrete part geometry, which reduces machining time and tool wear and can be used in high speed machining. The toolpath computation is based on image models for design part, raw stock and cutting tool, and involves pixel-based simulation of the milling process. Simulation results and comparison with existing methods are presented. [Copyright &y& Elsevier]

Abstract: This paper proposes a heuristic algorithm for near-optimal handling of the redundancy in robot mechanisms, applied to a 3D scanning platform consisting of a 6-DOF articulated robot arm which moves a laser sensor around a workpiece placed on a rotary table. The proposed method handles both static constraints, like avoiding joint limits, kinematic singularities or collisions, modelled using a configuration map viewed as a grayscale image, and dynamic constraints like velocity and acceleration. The algorithm is compared with Dijkstra algorithm, which gives the optimal solution, but is very slow, and with two other heuristics which are very fast, but give suboptimal solutions. [Copyright &y& Elsevier]

The purpose of these investigations is to study the possibilities to improve performances of a typical vertical axis wind turbines (VAWT), of Darrieus-type, using passive devices (mounted "on" or "inside" the blades of VAWT) to control dynamic flow separation (dynamic stall phenomenon). The passive devices considered for investigations are the Gurney flap, the slot or thin channel, and the turbulence promoters. Studies are performed numerically using computational fluid dynamics and where it is possible the results are compared with existent experimental or numerical data. (© 2014 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim) [ABSTRACT FROM AUTHOR]

Clostridium (Ruminiclostridium) thermocellum is a model organism for its ability to deconstruct plant biomass and convert the cellulose into ethanol. The bacterium forms biofilms adherent to lignocellulosic feedstocks in a continuous cell-monolayer in order to efficiently break down and uptake cellulose hydrolysates. We developed a novel bioreactor design to generate separate sessile and planktonic cell populations for omics studies. Sessile cells had significantly greater expression of genes involved in catabolism of carbohydrates by glycolysis and pyruvate fermentation, ATP generation by proton gradient, the anabolism of proteins and lipids and cellular functions critical for cell division consistent with substrate replete conditions. Planktonic cells had notably higher gene expression for flagellar motility and chemotaxis, cellulosomal cellulases and anchoring scaffoldins, and a range of stress induced homeostasis mechanisms such as oxidative stress protection by antioxidants and flavoprotein co-factors, methionine repair, Fe-S cluster assembly and repair in redox proteins, cell growth control through tRNA thiolation, recovery of damaged DNA by nucleotide excision repair and removal of terminal proteins by proteases. This study demonstrates that microbial attachment to cellulose substrate produces widespread gene expression changes for critical functions of this organism and provides physiological insights for two cells populations relevant for engineering of industrially-ready phenotypes. [ABSTRACT FROM AUTHOR]

Self- starting is the major obstacle to be overcome for successful design of a vertical axis wind turbine (VAWT). In the past has been suggested that pitching the turbine blades such that pitch angle is not 90 degrees allows for self-starting. To understand the physics surrounding pitching, an analysis is carried out for a common airfoil profile, NACA 0012. The vortex model is used to predict aerodynamic performance of VAWT with pitched blades at various angles. As a result of the analysis carried out for the airfoil at various pitch angles, it was shown that the 'dead band' phenomenon could be overcome, but only slightly. At the same time, to overcome the 'dead band' with a level on confidence, torques in the tip speed ratio (TSR ) range of 0.75 to 2.75 must be increased to values further above zero. The paper aimed at giving an insight into the small wind turbine starting behavior and its influence parameters. (© 2013 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim) [ABSTRACT FROM AUTHOR]

Influence of Interphase Mass Transfer (IMT) on the unsteady convective diffusion in a fluid flow through a tube surrounded by a porous medium is examined against the background of no IMT. The three coefficients namely exchange coefficient, convection coefficient, and dispersion coefficient are evaluated asymptotically at large-time. The exchange coefficient exists due to IMT. All-time analysis is made analytically when there is no IMT. The mean concentration distribution is measured at a point inside and outside the slug. The peak of mean concentration is higher than that of pure convection and it is further enhanced with increase of porous parameter. (© 2012 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim) [ABSTRACT FROM AUTHOR]

Summary: Sustainable utilization of lignocellulosic perennial grass feedstocks will be enabled by high biomass production and optimized cell wall chemistry for efficient conversion into biofuels. MicroRNAs are regulatory elements that modulate the expression of genes involved in various biological functions in plants, including growth and development. In greenhouse studies, overexpressing a microRNA (miR156) gene in switchgrass had dramatic effects on plant architecture and flowering, which appeared to be driven by transgene expression levels. High expressing lines were extremely dwarfed, whereas low and moderate‐expressing lines had higher biomass yields, improved sugar release and delayed flowering. Four lines with moderate or low miR156 overexpression from the prior greenhouse study were selected for a field experiment to assess the relationship between miR156 expression and biomass production over three years. We also analysed important bioenergy feedstock traits such as flowering, disease resistance, cell wall chemistry and biofuel production. Phenotypes of the transgenic lines were inconsistent between the greenhouse and the field as well as among different field growing seasons. One low expressing transgenic line consistently produced more biomass (25%–56%) than the control across all three seasons, which translated to the production of 30% more biofuel per plant during the final season. The other three transgenic lines produced less biomass than the control by the final season, and the two lines with moderate expression levels also exhibited altered disease susceptibilities. Results of this study emphasize the importance of performing multiyear field studies for plants with altered regulatory transgenes that target plant growth and development. [ABSTRACT FROM AUTHOR]