Search

Researchers agree that the ideal scaffold for tissue engineering should possess a 3D and highly porous structure, biocompatibility to encourage cell/tissue growth, suitable surface chemistry for cell attachment and differentiation, and mechanical properties that match those of the surrounding tissues. However, there is no consensus on the optimal pore distribution. In this study, we investigated the effect of pore distribution on corrosion resistance and performance of human mesenchymal stem cells (hMSC) using titanium scaffolds fabricated by laser beam powder bed fusion (PBF-LB). We designed two scaffold architectures with the same porosities (i.e., 75 %) but different distribution of pores of three sizes (200, 500, and 700 μm). The pores were either grouped in three zones (graded, GRAD) or distributed randomly (random, RAND). Microfocus X-ray computed tomography revealed that the chemically polished scaffolds had the porosity of 69 ± 4 % (GRAD) and 71 ± 4 % (RAND), and that the GRAD architecture had the higher surface area (1580 ± 101 vs 991 ± 62 mm 2 ) and the thinner struts (221 ± 37 vs 286 ± 14 μm). The electrochemical measurements demonstrated that the apparent corrosion rate of chemically polished GRAD scaffold decreased with the immersion time extension, while that for polished RAND was increased. The RAND architecture outperformed the GRAD one with respect to hMSC proliferation (over two times higher although the GRAD scaffolds had 85 % higher initial cell retention) and migration from a monolayer. Our findings demonstrate that the pore distribution affects the biological properties of the titanium scaffolds for bone tissue engineering., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier B.V. All rights reserved.)

The present study investigates the correlation between mechanical properties and resistance to corrosion of hydrostatically extruded aluminum alloy 7075. Supersaturated solid solutionized samples undergo a plastic deformation process, followed by both natural and artificial aging. Furthermore, two types of hydrostatic extrusion are applied to the samples: single-stepped and double-stepped. This process is shown to influence grain refinement and the precipitation process, resulting in changes in the electrochemical properties of the samples. Hydrostatic extrusion combined with aging is shown to cause an increase in mechanical strength ranging from 50 MPa to 135 MPa in comparison to coarse-grained sample subjected to T6 heat treatment. The highest value of tensile strength is obtained for a sample subjected to single-step hydrostatic extrusion followed by natural aging. This strength increase is caused by refinement of the microstructure, in addition to the small size and number of precipitates at the grain boundaries, which are coarsened by artificial aging. Hydrostatic extrusion is also shown to increase resistance to corrosion, with the T6-treated coarse-grained sample being most susceptible to corrosion attack.

In this paper, the corrosion resistance and mechanical properties of the 7075 aluminum alloy are studied. The alloy was deformed by hydrostatic extrusion and then aged both naturally and artificially. Results are compared with those of coarse-grained material subjected to T6 heat treatment. The aim of the research is to find the optimal correlation between the mechanical properties and the corrosion resistance of the alloy. To this end, static tensile tests with subsequent fractography, open circuit potential, and potentiodynamic polarization tests in 0.05 M NaCl were conducted. Obtained results show that a combination of precipitate hardening and a deformed microstructure leads to increased mechanical strength with high anisotropy due to the presence of fibrous grains. Plastic deformation increases susceptibility to corrosion due to the increased number of grain boundaries, which act as paths along that corrosion propagates. However, further artificial aging incurs a positive effect on corrosion resistance due to changes in the chemical composition of the matrix as a result of the precipitation process.

Aluminium (Al) and titanium (Ti) coatings were applied on AZ91E magnesium alloy using a low-pressure warm spray (WS) method. The deposition was completed using three different nitrogen flow rates (NFR) for both coatings. NFR effects on coating microstructure and other physical properties were systematically studied. Microstructural characterization was performed using scanning electron microscopy (SEM), and the porosity was estimated using two methods-image analysis and X-ray microtomography. The coating adhesion strength, wear resistance, and hardness were examined. The protective properties of the coatings were verified via a salt spray test. Decreasing NFR during coating deposition produced more dense and compact coatings. However, these conditions increased the oxidation of the powder. Al coatings showed lower hardness and wear resistance than Ti coatings, although they are more suitable for corrosion protection due to their low porosity and high compactness.

The effect of aging on the resistance to pitting corrosion of ultrafine-grained 7475 aluminium (Al) alloy processed by hydrostatic extrusion (HE) is studied. Differences in the microstructure were investigated using secondary electron (SEM) and transmission electron microscopy (TEM). Corrosion tests were performed in 0.1 M NaCl, and characterization of corroded surface was performed. The results of this work show that the pitting susceptibility of ultra-fine grained 7475Al is related to the distribution of MgZn 2 precipitates. After HE, the formation of An ultrafine-grained microstructure at the grain boundaries of ultrafine grains is observed, while subsequent aging results in the formation of MgZn 2 precipitates in the grain interior. Grain refinement increases susceptibility to localized attack, while the subsequent aging improves the overall corrosion resistance and limits the propagation of corrosion attack.

The effect of hydrostatic extrusion (HE) on the microstructure, uniform corrosion, and susceptibility to a localized attack of 316L stainless steel was studied. Both qualitative and quantitative analyses of inclusions before and after HE were carried out. The multiplication of non-metallic inclusions after HE lowered the stability of the passive film over a broad range of pH, while refinement of the matrix had a minor effect on it. The refined materials were prone to metastable pitting, but their pitting corrosion resistance was improved.