Search

Porcelain laminate veneers are a conservative treatment to enhance esthetics, tooth shape, color, and contours. Enamel preservation during tooth preparation is essential for the long-term success of these micromechanically retained partial coverage restorations. Different methods have been described to clinically assess tooth preparation relative to definitive restorative contours. This clinical report describes a digital workflow to fabricate 3-dimensionally (3D) printed tooth reduction guides based on digital esthetic planning. These 3D-printed reduction guides help clinicians visualize and gauge tooth preparations relative to the desired restorative contours, aid in enamel preservation, and overcome some of the limitations associated with conventionally fabricated tooth reduction guides.

Statement of problem The clinical survival of different types of post-and-core systems requires assessment. Purpose The purpose of this retrospective clinical study was to evaluate the clinical survival rate (CSR) of custom-fabricated cast metal and prefabricated (both metal- and fiber-reinforced composite resin post) post-and-cores as a function of patient- and restoration-related variables. Material and methods A retrospective analysis was conducted on electronic charts indicating that these patients had received some type of post-and-core between January 2003 and January 2018. A total of 754 records were included in the analysis based on the inclusion criteria. Data were analyzed by using the Kaplan-Meier and Cox proportional hazards analysis. Results Kaplan-Meier analysis demonstrated the mean survival time for each group to be 12.0 years for fiber-reinforced composite resin posts, 11.8 years for cast metal post-and-cores, and 10.2 years for prefabricated metal posts. Although the mean survival time differed by 1.8 years among groups, with prefabricated metal posts having a slightly higher risk of failure, this effect was not statistically significant (P=.067). The effect of post type also failed to reach significance when controlling for patient demographics and post position in a Cox proportional hazards analysis (P=.106). However, the Cox model did show that survival was associated with tooth position (P=.003), cement (P=.021), and type of restoration (P Conclusions Analysis showed no evidence that post-and-core survival was significantly associated with 3 types of post-and-cores (custom-fabricated metal, prefabricated metal, and prefabricated fiber-reinforced composite resin). The percentage of root in the bone, tooth position, cement, and type of restoration, however, were significantly associated with survival.

Tooth decay is a prevalent disease that initiates when the oral pH becomes acidic. Fluoride and/or bioactive glass (NovaMin) were used to regenerate/repair teeth that had been decalcified. In this present study, we investigated the effect of fluoride and/or bioactive glass (NovaMin) on remineralization of hydroxyapatite (HA) discs, which mimic the enamel surface of natural teeth. HA discs were etched with phosphoric acid and treated with one of the following toothpastes: (1) Sensodyne toothpaste with fluoride, (2) Sensodyne toothpaste with fluoride and bioactive glass (NovaMin), (3) Tom’s toothpaste without fluoride or bioactive glass (NovaMin), and (4) Tom’s toothpaste with bioactive glass (NovaMin). The toothpastes were applied on the etched discs for two minutes, once a day for 15 days. Scanning electron microscopy (SEM) was used to analyze surface morphologies and X-ray photoelectron spectroscopy (XPS) was used to analyze surface compositions. Tom’s toothpaste with only NovaMin demonstrated the most remineralization potential compared with the other groups. In conclusion, incorporating bioactive glass (NovaMin) into toothpastes could benefit the repair and remineralization of teeth.

STATEMENT OF PROBLEM: Whether tooth whitening alters the surface topography of enamel causing an increase in surface roughness that could increase susceptibility to restaining is unclear. PURPOSE: The purpose of this in vitro study was to evaluate whether immersing enamel in common solutions produces a color change of ΔE greater than 2; whether the highest concentration carbamide peroxide bleaching agent produces the greatest ΔE; whether bleaching increases the susceptibility to further staining by common solutions; and whether morphologic changes to the enamel surface are observed after staining and bleaching as evidenced by scanning electron microscopy (SEM) analysis and energy-dispersive x-ray spectroscopy (EDS). MATERIAL AND METHODS: Forty-five extracted human teeth were immersed in 5 solutions (wine, coffee, tea, soda, and water) for 15 days at 80°C, and the change in ΔE was assessed with a colorimeter. The teeth were bleached using different concentrations of carbamide peroxide (20%, 35%, and 44%) and ΔE was measured at different time intervals. The teeth were then restained with the same solutions. The ΔE after initial staining was compared with the ΔE after bleaching and restaining of the same teeth. SEM was performed at baseline, after staining, bleaching, and restaining to evaluate the changes in the enamel surface topography. EDS was used to determine the elemental composition of tooth surfaces after restaining. RESULTS: All liquids caused a ΔE greater than 2 after 15 days. The concentration of bleaching agent was not significantly associated with ΔE for any stain types. No significant difference was found in the rate of staining between initial staining and restaining after bleaching. However, a significant effect of time was found for the staining, where the overall ΔE increased by 0.34 for each day in the solution (P

Titanium (Ti) corrodes clinically in the presence of bacteria. We investigated this phenomenon as a function of Ti particles found in biopsied tissues around peri-implantitis sites and surface roughness of failed Ti implants. Tissue biopsies were surgically collected from peri-implantitis sites, processed, and embedded in resin. The resin-embedded samples were hand trimmed to the region of interest and semi-thick (500 nm) sections were collected onto coverslips. One section was toluidine blue post-stained as a reference. The remainder sections were left unstained for energy-dispersive X-ray spectroscopy (EDX) analysis. Processed samples were examined under scanning electron microscopy (SEM) and EDX. Corresponding failed implants were also removed and examined under SEM and EDX. Five out of eight biopsied samples demonstrated the presence of Ti particles in the soft tissue, suggesting the true rate among all failures was between 24.5% and 91.5% (the lower bound of a 95% confidence interval for the true rate of Ti presence). SEM analysis of failed implant bodies also indicated changes in surface morphology and appeared less detailed with decreased weight percent of Ti on the surface of the failed implants. In conclusion, Ti particles were noted in 5/8 biopsied samples. Surface morphologies were smoother in failed implants compared with the reference implant.

Purpose: The aim of this study was to determine stress levels on supporting structures of implant-retained overdentures as a function of varying degrees of palatal coverage using finite element analysis modeling at different loading angles. Materials and Methods: ABAQUS&reg, software was used to perform finite element analysis on eight overdenture models with three and four implants and with and without palatal coverage designs. Loads were applied perpendicular and 45&ordm, to the implants. Von Mises stress was measured to determine bone stress. A one-way ANOVA determined which model caused the most stress to the maxillary bone. Results: Palatal coverage increased stress to anterior implant in three implant (p = 0.08) models but decreased stress to all implants in four implant models (p = 0.43). Distal implants received more stress than anterior implants for all models. There was no significant difference between a full palate and no palate coverage overdenture prosthesis when a bar was added under axial loading (p = 0.954). Under non-axial loading, a decrease in stress was noted with the bar in all areas except the anterior implant site. Conclusions: Palatal coverage may not be necessary when applying a pure axial load. The addition of a bar decreased stress at loading.