Search

The residues of erythromycin (ERY) may have negative impacts on the ecological environment, health, and food safety. How to detect ERY effectively and visually is a challenging issue. Herein, we synthesized a molecularly imprinted polymer based nanozymes for selective detection of erythromycin (ERY-MIPNs) at neutral pH, and developed a mobile phone-assisted bicolor colorimetric detection system. This system produced a wide range of color changes from blue to pinkish purple as the ERY concentration increased, making it easy to capture the visualization result. Also, the system showed good sensitivity to ERY ranging from 15 to 135 μM, with a detection limit of 1.78 μM. In addition, the system worked well in the detection of ERY in river water and milk, with the recoveries of 95.57% ∼ 103.20%. These data suggests that this strategy is of considerable potential for practical applications and it provides a new idea for visual detection with portable measurement., Competing Interests: Declaration of competing interest The authors declare no conflict of interest., (Copyright © 2023. Published by Elsevier Ltd.)

Adverse effects of pharmaceutical emerging contaminants (PECs), including antibiotics, in water supplies has been a global concern in recent years as they threaten fresh water security and lead to serious health problems to human, wildlife and the environment. However, detection of these contaminants in water sources, as well as food products, is difficult due to their low concentration. Here, we prepared a new family of magnetic molecular imprinted polymer (MMIP) networks for binding antibiotics via a microemulsion polymerization technique using vinyl silane modified Fe 3 O 4 magnetic nanoparticles. The cross-linked polymer backbone successfully integrated with 20-30 nm magnetic nanoparticles and generated a novel porous polymeric network structure. These networks showed a high binding capacity for both templates, erythromycin and ciprofloxacin at 70 and 32 mg/g. Both MMIPs were also recyclable, retaining 75 % and 68 % of the binding capacity after 4 cycles. These MMIPs have showed a clear preference for binding the template molecules, with a binding capacity 4- to 7-fold higher than the other antibiotics in the same matrix. These results demonstrate our MMIP networks, which offered high binding capacity and selectivity as well as recyclability, can be used for both removal and monitoring hazardous antibiotic pollutants in different sources/samples and food products., Competing Interests: Declaration of Competing Interest There is no conflict of interest to declare., (Copyright © 2019 Elsevier B.V. All rights reserved.)

Pharmaceuticals constitute one of the most important emerging classes of environmental pollutants. A three-phase solvent system of water, water containing 0.1% of formic acid and acetonitrile was successfully used to separate, by liquid chromatography with mass spectrometry (LC-MS), polarity-matched pharmaceuticals, that is, carbamazepine, clarithromycin, and erythromycin, as well as amoxicillin and metformin. Despite of polarity similarities, these pharmaceuticals were completely resolved in the analytical run time of 15 min. The optimized three-phase solvent system based-method was validated for the simultaneous analysis of six matched-polarity pharmaceuticals in wastewater samples. Good linearity (coefficient of determination more than 0.993) and precision (relative standard deviation less than 15.66%) were achieved. Recovery of analytes from the wastewater was between 0.70 and 1.18. Limits of detections ranged from 0.0001 to 0.5114 µg/L. No significant matrix effect, evaluated by post extraction addition, was observed in the electrospray ionization (ESI) source. Then, this methodology has been successfully applied to environmental study of pharmaceutical residues occurring in influent and effluent wastewater samples, from the main wastewater treatment plant in Potenza (Basilicata, Southern Italy)., (© 2019 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Erythromycin A is an important antibiotic. A chemically defined synthetic medium for erythromycin production was systematically optimized in this study. A high-throughput method was employed to reduce the number of components and optimize the concentration of each component. After two round single composition deletion experiment, only 19 components were remained in the medium, and then the concentration of each component was optimized through PB experiment. The optimal medium from the PB experiment was further optimized according to the nitrogen and phosphate metabolic consumption in 5 L bioreactor. It was observed that among the 8 amino acids concluded in the media, 4 amino acids were first consumed, when they are almost depleted, the other 4 amino acids were initiated their consumption afterwards in 5 L bioreactor. The decrease of phosphate concentration would increase q glc and q ery . However, when phosphate concentration was too low, the production of erythromycin was hindered. The positive correlation between intracellular metabolite pools and Y ery/glc indicated that low phosphate concentration in the medium can promote cell metabolism especially secondary metabolism during the stationary phase; however, if it was too low (5 mmol/L), the cell metabolism and secondary metabolism would both slow down. The erythromycin titer in the optimized medium (medium V) reached 1380 mg/L, which was 17 times higher than the previously used synthetic medium in our lab. The optimized medium can facilitate the metabolomics study or metabolic flux analysis of the erythromycin fermentation process, which laid a solid foundation for further study of erythromycin fermentation process.

Metabolomics is essential to understand the metabolism and identify engineering targets to improve the performances of strains and bioprocesses. Although numerous metabolomics techniques have been developed and applied to various organisms, the metabolome of Saccharopolyspora erythraea, a native producer of erythromycin, had never been studied. The 2017 best paper of Bioprocess and Biosystems Engineering reports examination of three methods for quenching and extraction to analyze the intracellular metabolome of S. erythraea, and identified the most reliable methods for studying different groups of the metabolites. Subsequent studies on the dynamics of the intracellular metabolome of S. erythraea during the fed-batch fermentation identified a positive correlation between the specific erythromycin production rate and the pool size of intracellular propionyl-CoA and other precursors of erythromycin. A series of follow-up studies, such as demonstrating the applicability of the quenching/extraction methods in other related antibiotic producers, demonstrating the generality of the best matches between the quenching/extraction methods and the metabolite groups, and combining metabolomics approaches with the fluxomics and systems metabolic engineering approaches, will facilitate the metabolomics studies on important antibiotic producers, enable standardization of the quenching/extraction protocols, and improve the performance of the antibiotic production with deeper insight into their metabolism.

In this study, we developed a novel photoelectrochemical (PEC) sensor for the highly sensitive detection of erythromycin by functionalising graphene oxide (GO) with nickel tetra-amined phthalocyanine (NiTAPc) through covalent bonding, which resulted in the formation of NiTAPc-Gr. The fabricated sensor showed a higher PEC efficiency under blue light, exhibiting a peak wavelength of 456 nm, as compared to that of the monomer. Further, the NiTAPc-Gr/indium tin oxide (ITO) sensor exhibited a photocurrent that was 50-fold higher than that for a GO/ITO sensor under the same conditions. Under optimal conditions, the NiTAPc-Gr PEC sensor showed a linear response for erythromycin concentrations ranging from 0.40 to 120.00 μmol L -1 , with the minimum limit for detection being 0.08 μmol L -1 . Thus, the NiTAPc-Gr sensor exhibited superior performance and excellent PEC characteristics, high stability, and good reproducibility with respect to the sensing of erythromycin. Moreover, it is convenient to use, fast, small, and cheap to produce. Hence, it should find wide use in the analysis of erythromycin in real-world applications., (Copyright © 2018 Elsevier B.V. All rights reserved.)

Reverse micelles extraction of erythromycin and amoxicillin were carried out using the novel Sophorolipids biosurfactant. By replacing commonly used chemical surfactants with biosurfactant, reverse micelle extraction can be further improved in terms of environmental friendliness and sustainability. A central composite experimental design was used to investigate the effects of solution pH, KCl concentration, and sophorolipids concentration on the reverse micelle extraction of antibiotics. The most significant factor identified during the reverse micelle extraction of both antibiotics is the pH of aqueous solutions. Best forward extraction performance for erythromycin was found at feed phase pH of approximately 8.0 with low KCl and sophorolipids concentrations. Optimum recovery of erythromycin was obtained at stripping phase pH around 10.0 and with low KCl concentration. On the other hand, best forward extraction performance for amoxicillin was found at feed phase pH around 3.5 with low KCl concentration and high sophorolipids concentration. Optimum recovery of erythromycin was obtained at stripping phase pH around 6.0 with low KCl concentration. Both erythromycin and amoxicillin were found to be very sensitive toaqueous phase pH and can be easily degraded outside of their stable pH ranges.

Antibiotics are frequently used in animals to treat sickness and prevent infection especially in industrial meat production. Some of the antibiotics cannot be completely metabolized and, as an unavoidable result, are excreted and thus end up in manure which is then spread in the environment. Currently increasing amounts of manure is used in biogas production before spreading the residuals on agricultural fields. In this study, the removal patterns of sulfonamides (sulfadiazine, sulfamethizole, sulfamethoxazole) and macrolides (clarithromycin, erythromycin), as well as trimethoprim, were investigated during the anaerobic digestion of pig manure. Batch kinetic tests were conducted both at thermophilic and psychrophilic condition for 40 days. Some of the antibiotics (clarithromycin, sulfadiazine, sulfamethizole) were persistent in all experiments. Thus, no biodegradation was found for sulfadiazine and sulfamethizole in this study. From the studied compounds, only erythromycin was clearly removed and probably degraded during anaerobic digestion with 99% and 20% removal under thermophilic and psychrophilic condition. The removal of erythromycin was fitted to a single first-order kinetic reaction function, giving reaction rate constant of 0.29day -1 and 0.005day -1 , respectively., (Copyright © 2017 Elsevier B.V. All rights reserved.)

An erythromycin (ERY) detection method is proposed using the fiber optic core decorated with the coatings of silver and an over layer of ERY imprinted nanoparticles. Synthesis of ERY imprinted nanoparticles is carried out using miniemulsion method. The operating range of the sensor is observed to be from 1.62×10 -3 to 100µM while the sensor possesses the linear response for ERY concentration range from 0.1 to 5µM. The sensing method shows a maximum sensitivity of 205nm/µM near ERY concentration of 0.01µM. The detection limit and the quantification limit of the sensor are found to be 1.62×10 -3 µM and 6.14×10 -3 µM, respectively. The sensor's applicability in real samples is also examined and is found to be in good agreement for the industrial application. The sensor possesses numerous advantages like fast response time (<15s), simple, low cost, highly selective along with abilities towards online monitoring and remote sensing of analyte., (Copyright © 2016 Elsevier B.V. All rights reserved.)

Erythromycin A, the main component of erythromycin, is widely used to treat and control foulbrood diseases in honey bees. In this study, we developed a fast and sensitive method to simultaneously determine erythromycin A and its degradation products in honey. The analytical methodology was based on dispersive liquid-liquid microextraction and liquid chromatography coupled with tandem mass spectrometry with advanced i-Funnel technology. The liquid-liquid microextraction and liquid chromatography coupled with tandem mass spectrometry parameters were optimized. The recoveries of erythromycin A and its degradation products from spiked honey samples were 76.1-102.1%, with reproducibility rates of 7.1-13.1% and correlation coefficients  >0.99. The decision limit and detection capability were 0.02-0.07 and 0.03-0.10 ng/g, respectively. The proposed method was validated and successfully applied to the determination of the target analytes in commercial honey samples. It was efficient and sensitive, and it lays the foundation for further research on honey safety., (© 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Leucine-responsive regulatory proteins (Lrps) are a group of transcriptional regulators that regulate diverse cellular processes in bacteria and archaea. However, the regulatory role of Lrps in antibiotic biosynthesis remains poorly understood. In this study, we show that SACE&#95;5388, an Lrp family regulator named as SACE&#95;Lrp, is an efficient regulator for transporting and catabolizing branched-chain amino acids (BCAAs), playing an important role in regulating erythromycin production in Saccharopolyspora erythraea. SACE&#95;Lrp directly controlled the expression of the divergently transcribed SACE&#95;5387-5386 operon putatively encoding a BCAA ABC transporter by interacting with the intergenic region between SACE&#95;Lrp and SACE&#95;5387 (SACE&#95;Lrp-5387-int), and indirectly controlled the expression of ilvE putatively encoding an aminotransferase catabolizing BCAAs. BCAA catabolism is one source of the precursors for erythromycin biosynthesis. Lysine and arginine promoted the dissociation of SACE&#95;Lrp from SACE&#95;Lrp -5387-int, whereas histidine increased their binding. Gene disruption of SACE&#95;Lrp (ΔSACE&#95;Lrp) in S. erythraea A226 resulted in a 25% increase in erythromycin production, while overexpression of SACE&#95;5387-5386 in A226 enhanced erythromycin production by 36%. Deletion of SACE&#95;Lrp (WBΔSACE&#95;Lrp) in the industrial strain S. erythraea WB enhanced erythromycin production by 19%, and overexpression of SACE&#95;5387-5386 in WBΔSACE&#95;Lrp (WBΔSACE&#95;Lrp/5387-5386) increased erythromycin production by 41% compared to WB. Additionally, supplement of 10mM valine to WBΔSACE&#95;Lrp/5387-5386 culture further increased total erythromycin production up to 48%. In a 5-L fermenter, the erythromycin accumulation in the engineered strain WBΔSACE&#95;Lrp/5387-5386 with 10mM extra valine in the industrial culture media reached 5001mg/L, a 41% increase over 3503mg/L of WB. These insights into the molecular regulation of antibiotic biosynthesis by SACE&#95;Lrp in S. erythraea are instrumental in increasing industrial production of secondary metabolites., (Copyright © 2016 International Metabolic Engineering Society. Published by Elsevier Inc. All rights reserved.)

A solid-phase extraction/liquid chromatography/electrospray ionization/multi-stage mass spectrometry (SPE-LC-ESI-MS/MS) method was optimized in this study for sensitive and simultaneous detection of multiple antibiotics in urban surface waters and soils. Among the seven classes of tested antibiotics, extraction efficiencies of macrolides, lincosamide, chloramphenicol, and polyether antibiotics were significantly improved under optimized sample extraction pH. Instead of only using acidic extraction in many existing studies, the results indicated that antibiotics with low pK a values (<7) were extracted more efficiently under acidic conditions and antibiotics with high pK a values (>7) were extracted more efficiently under neutral conditions. The effects of pH were more obvious on polar compounds than those on non-polar compounds. Optimization of extraction pH resulted in significantly improved sample recovery and better detection limits. Compared with reported values in the literature, the average reduction of minimal detection limits obtained in this study was 87.6% in surface waters (0.06-2.28 ng/L) and 67.1% in soils (0.01-18.16 ng/g dry wt). This method was subsequently applied to detect antibiotics in environmental samples in a heavily populated urban city, and macrolides, sulfonamides, and lincomycin were frequently detected. Antibiotics with highest detected concentrations were sulfamethazine (82.5 ng/L) in surface waters and erythromycin (6.6 ng/g dry wt) in soils. The optimized sample extraction strategy can be used to improve the detection of a variety of antibiotics in environmental surface waters and soils.

The synthesis of macroporous molecularly imprinted monoliths was performed using the monomers system 2-hydroxyethyl methacrylate-ethylene glycol dimethacrylate and erythromycin as a template. The copolymerization was carried out in situ inside 50 mm × 4.6 mm i.d. stainless-steel tubing. The morphology of the monoliths was examined with scanning electron microscopy. The porous characteristics were determined both from the data of hydrodynamic permeability of monoliths and by means of mercury intrusion porosimetry. The retention parameters of target substance (erythromycin), values of calculated imprinting factors and apparent dynamic dissociation constants were obtained for monoliths prepared with the application of different amount of template (4, 8 and 12 mol%). The separations of the mixtures azithromycin/erythromycin and ciprofloxacin/erythromycin were demonstrated. Additionally, the possibility of erythromycin quantification in human blood plasma was shown., (© 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Magnetic imprinted polymers (MIPs) were synthesized by Pickering emulsion polymerization and used to adsorb erythromycin (ERY) from aqueous solution. The oil-in-water Pickering emulsion was stabilized by chitosan nanoparticles with hydrophobic Fe3O4 nanoparticles as magnetic carrier. The imprinting system was fabricated by radical polymerization with functional and crosslinked monomer in the oil phase. Batches of static and dynamic adsorption experiments were conducted to analyze the adsorption performance on ERY. Isotherm data of MIPs well fitted the Freundlich model (from 15 °C to 35 °C), which indicated heterogeneous adsorption for ERY. The ERY adsorption capacity of MIPs was about 52.32 μmol/g at 15 °C. The adsorption kinetics was well described by the pseudo-first-order model, which suggested that physical interactions were primarily responsible for ERY adsorption. The Thomas model used in the fixed-bed adsorption design provided a better fit to the experimental data. Meanwhile, ERY exhibited higher affinity during adsorption on the MIPs compared with the adsorption capacity of azithromycin and chloramphenicol. The MIPs also exhibited excellent regeneration capacity with only about 5.04% adsorption efficiency loss in at least three repeated adsorption-desorption cycles., (Copyright © 2015 Elsevier B.V. All rights reserved.)

Magnetic molecularly imprinted polymers (MMIPs) were prepared based on surface molecular imprinting using erythromycin (ERY) as template molecule and Fe3O4 nanoparticles as support substrate. The MMIPs possessed high adsorption capacity of 94.1 mg/g for ERY and the imprinting factor was 11.9 indicating good imprinted effect for ERY. Selective evaluation demonstrated favorable selectivity of MMIPs for multiple macrolide antibiotics (MACs). Using MMIPs as adsorptive material, a rapid and convenient magnetic solid-phase extraction (MSPE) procedure was established for simultaneous and selective separation of six MACs in pork, fish and shrimp samples, then the MACs was subjected to high-performance liquid chromatography-ultraviolet (HPLC-UV) analysis. At different fortified concentrations, the extraction recoveries could reach 89.1% and the relative standard deviations were lower than 12.4%. Chromatogram revealed the response signals of MACs in spiked samples were greatly enhanced and matrix interferences were effectively eliminated after treatment with MSPE. The proposed MSPE procedure coupled with HPLC-UV realized selective and sensitive determination of multiple MACs in foodstuff samples., (Copyright © 2015 Elsevier B.V. All rights reserved.)

The tandem mass spectrometry techniques electron-induced dissociation (EID) and collision-activated dissociation (CAD) have been compared as tools for providing detailed structural information of polyketides. Polyketides are an important class of natural products that account for a significant proportion of the drugs currently in clinical use. Three polyketide natural products, namely erythromycin A, lasalocid A, and iso-lasalocid A, were subjected to both CAD and EID, and their fragment ions were assigned with sub-part-per-million accuracy. The number of fragment ions detected through EID was much greater than for CAD, leading to a greater amount of structural information obtained for each polyketide, albeit with a decreased signal-to-noise ratio. The effect of different bound cations on the fragment pattern of the isomers lasalocid A and iso-lasalocid A was studied, with CAD and EID performed on the [M + H](+), [M + Na](+), [M + Li](+), and [M + NH(4)](+) precursor ions. The lithiated species were found to produce the greatest degree of fragmentation and enabled detailed structural information on the isomers to be obtained. Multistage mass spectrometry (MS(3)) experiments, combining CAD and EID, could also be performed on the lithiated species, generating new fragment information which enables the two isomers to be distinguished. Combining CAD and EID for the structural characterization of polyketides will therefore be a useful tool for identifying and characterizing unknown polyketides and their biosynthetic intermediates.

New hydrophilic polymer sorbents comprising reactionary sites which are complementary to a molecule of antibiotic erythromycin were synthesized by the method of molecular imprinting. A series of similar sorbents without reactionary sites was used for comparison of sorption characteristics. Sorption of erythromycin on both types of polymer sorbents synthesized was studied in a wide range of pH and ionic strength. Selectivity of erythromycin sorption on molecularly imprinted cross-linked polymers was shown to depend on the specific interaction of target molecule with polymer matrix. This type of sorbent is perspective for the development of antibiotic purification directly from a culture medium Saccharopolyspora erythreus.

A new surface imprinting technique was reported to synthesize multi-walled carbon nanotubes-molecularly imprinted polymers (MWNTs-MIPs) using erythromycin as the template, acryloyl-β-cyclodextrin (acryloyl-β-CD) and methacrylic acid (MAA) as the binary functional monomers. The MWNTs-MIPs were characterized by transmission electron microscopy (TEM), scanning electron micrograph (SEM) and Fourier transform-infrared spectroscopy (FT-IR). Adsorption experiments indicated the MWNTs-MIPs prepared with acryloyl-β-CD and MAA have high selective for erythromycin. The feasibility of the MWNTs-MIPs as solid-phase extraction (SPE) sorbent was evaluated, and the results showed that it can selectively extract erythromycin from chicken muscle samples with the recoveries ranging from 85.3% to 95.8%. The molecularly imprinted solid-phase extraction (MISPE) method could be applied for preconcentration and purification of erythromycin from chicken muscle samples., (Copyright © 2011 Elsevier B.V. All rights reserved.)

Analytical methods to improve the detection of erythromycin in water and sediment were developed to optimize for erythromycin's recovery of extractable and bound residues from the aquatic environment. The objective of this study was to determine optimal recovery of erythromycin from water and sediment to improve its detection in environmental samples through solid-phase extraction (SPE) and sediment-extraction methods. SPE methods examined included previously reported methods for macrolide and sulfonamide antibiotics with erythromycin recoveries ranging from 75.5 % to 94.7 %. Extraction of erythromycin was performed from sand employing various solvents and buffers to determine the best method for extraction from two sandy loam pond sediments. Various extraction times were also examined, and all extraction procedures were performed in duplicate. The greatest recovery of (14)C-erythromycin in the Iowa sediment was 84 % using 0.3 M ammonium acetate at pH 4.2: acetonitrile (15:85, v/v) solution. The Oklahoma sediment yielded the greatest recovery of (14)C-erythromycin at 86.7 % with 0.3 M ammonium acetate at pH 7: acetonitrile (30:70, v/v) with a 60-minute shake time. The present results demonstrate improved extraction methods for enhancing the accuracy of erythromycin detection from environmental samples.

A useful column characterisation system should help chromatographers to select the most appropriate column to use, e.g. when a particular chromatographic column is not available or when facing the dilemma of selecting a suitable column for analysis according to an official monograph. Official monographs of the European Pharmacopoeia and the United States Pharmacopeia are not allowed to mention the brand name of the stationary phase used for the method development. Also given the overwhelming offer of several hundreds of commercially available reversed-phase liquid chromatographic columns, the choice of a suitable column could be difficult sometimes. To support rational column selection, a column characterisation study was started in our laboratory in 2000. In the same period, Euerby et al. also developed a column characterisation system, which is now released as Column Selector by ACD/Labs. The aim of this project was to compare the two existing column characterisation systems, i.e. the KUL system and the Euerby system. Other research groups active in this field will not be discussed here. Euerby et al. developed a column characterisation system based on 6 test parameters, while the KUL system is based on 4 chromatographic parameters. Comparison was done using a set of 63 columns. For 7 different pharmaceutical separations (fluoxetine, gemcitabine, erythromycin, tetracycline, tetracaine, amlodipine and bisacodyl), a ranking was built based on an F-value (KUL method) or Column Difference Factor value (Euerby method) versus a (virtual) reference column. Both methods showed a similar ranking. The KUL and Euerby methods do not perfectly match, but they yield very similar results, allowing with a relatively high certainty, the selection of similar or dissimilar columns as compared to a reference column. An analyst that uses either of the two methods, will end up with a similar ranking. From a practical point of view, it must be noted that the KUL method only includes 4 parameters and 3 chromatographic methods compared to 6 parameters and 4 methods for the Euerby method. Hence, the time needed to determine the chromatographic properties of a column is shorter for the KUL approach. Access to the KUL method also requires no download procedures.

Occurrence and distribution of eight selected antibiotics were screened at four sewage treatment plants (STPs). Individual concentrations in raw influent and final effluent from the four STPs ranged from 16 to 1987 ng x L(-1) and from 16 to 2054 ng x L(-1), respectively. The other analytes were only detected in a few samples with lower concentrations. Antibiotics can not be removed completely at the four STPs with the highest removal efficiency reaching to 81%. Remarkable differences of the daily environmental loads (the sum of the amount in the final effluent and sludge) of the five most frequently detected compounds at the four STPs were found with mass data ranging from 0.5 to 828 g. The daily consumption per person in the charged area of selected STPs showed that more compounds, especially the erythromycin-H2O, were consumed each day in Guangzhou than in Hong Kong.

A novel and suitable clean-up method that allows, for the first time, the simultaneous determination of a rather large number of macrolide antibiotics (erythromycin, rosamicin, spiramycin, tylosin, kitasamycin and josamycin in feedingstuffs by high performance liquid chromatography with electrochemical detection (HPLC-ECD) is presented in this work. The effectiveness of the developed clean-up method allows the quantification of the target macrolides in poultry feed using standard calibration curves instead of matrix matched standards, which overcomes the general problem of finding representative blanks. Furthermore an additional back extraction included in the sample preparation procedure allows the determination of an additional macrolide (oleandomycin) with detection limits, expressed as apparent concentration in poultry feed, ranging from 0.04 to 0.22 mg kg(-1) and relative standard deviation values ranging from 3.6 to 10.1% depending on the target analyte. Moreover, this additional step has been proven to enlarge the scope of the method by the extension of its applicability, at the target level of concentration, to other animal feedingstuffs such as pig and cattle. The analysis of real feedingstuffs containing macrolides demonstrated the fitness for purpose of the whole analytical procedure as well as a good fitting between real and spiked samples. The proposed methods appeared therefore as a sound alternative in the frame of control (e.g. for post-screening purposes) and/or monitoring surveillance programmes at the target level of 1.0 mg kg(-1) established according to the reported lowest dosage of additive needed to lead a growth promoting effect.

A rapid, simple and sensitive liquid chromatography-UV diode-array detection method was developed for the simultaneous determination of seven macrolides (erythromycin, oleandomycin, roxithromycin, josamycin, spiramycin, tylosin and ivermectin) in sheep's milk. The column, mobile phase, temperature and flow rate were optimised to provide the best resolution of these analytes. The extraction of the antibiotic residues involves the treatment of protein-free samples with a combination of concentrated sodium hydroxide and ethyl acetate. Necessary defatting is achieved by alkaline hydrolysis. The recovery of each antibiotic was between 55% and 77%, with relative standard deviations ranging from 1% to 6.5%. The limit of quantification was 72.4 microg/kg for ivermectin, 48.3 microg/kg for roxithromycin, and 24.1 microg/kg for erythromycin, oleandomycin, spiramycin, josamycin and tylosin. The procedure was successfully used in the multi-residue determination of these macrolides at levels below the maximum concentrations legally allowed in milk samples.

The use of special synthetic sorbents with surface carboxyl groups allowed us to increase fourfold the effective diffusion coefficient for erythromycin. The maximum sorption capacity for the antibiotic exceeded twofold that observed in experiments with a macroporous sulfocation exchanger MN-500. The sorption of the antibiotic was completely reversible upon treatment with a combined eluant that competitively interacts with the sorbent and does not impair the structural characteristics of erythromycin.

Counter-current chromatography (CCC) is a low pressure, liquid-liquid chromatographic technique which has proven to be a powerful purification tool for the high-resolution fractionation of a variety of active pharmaceutical compounds. The successful integration of CCC into either existing or new manufacturing processes requires the predictable purification of target compounds from crude, fermentation-derived, feed streams. This work examines the feasibility of CCC for the purification of fermentation-derived erythromycin A (EA) from its structurally and chemically similar analogues. At the laboratory scale, the effect of feed pre-treatment using either clarified, forward extracted (butyl acetate) or back extracted broth on EA separation was investigated. This defined the degree of impurity removal required, i.e. back extracted broth, to ensure a reproducible elution profile of EA during CCC. Optimisation and scale-up of the separation studied the effects of mobile phase flow (2-40 ml.min(-1)) and solute loading (0.1-10 g) on the attainable EA purity and yield. The results in all cases demonstrated a high attainable EA purity (>97% w/w) with throughputs up to 0.33 kg.day(-1). Secondly, a predictive scale-up model was applied demonstrating, that from knowledge of the solute distribution ratio of EA (K(EA)) at the laboratory scale, the EA elution time at the pilot scale could be predicted to within 3-10%, depending upon the solute injection volume. In addition, this study has evaluated a "fractionation diagram" approach to visually determine the effects of key operational variables on separation performance. This resulted in accurate fraction cut-point determination for a required degree of product purity and yield. Overall, the results show CCC to be a predictable and scaleable separation technique capable of handling real feed streams.

Natural products have been used as medicinal agents for many years. In addition, these compounds have served as the starting points for semisynthetic analogs with improved properties. This review highlights work on several classes of natural products and their derivatives, including both well established and emerging structural classes that are in, or nearing, clinical use for a variety of important indications.

In this study the selective adsorption method was chosen to enable the recovery of erythromycin. The following sorbents were tested: neutral resins (XAD-4, XAD-7 and XAD-16) and an anionic resin (IRA-410). A mathematical kinetic model for the adsorption of erythromycin against time, on XAD-4, XAD-7 and XAD-16 resins, is proposed. Both Freundlich and Langmuir models showed a good fit for the sorbents XAD-7 and IRA-410 resins. The highest adsorption efficiency was observed when synthetic neutral resin, XAD-7 and XAD-16, were used. The estimated affinity and concentration factors show that the neutral resins tested are adequate for the selective adsorption of erythromycin. The estimated values of enthalpy and free energy of adsorption, lower than 12 kJ mol(-1) and -2 kJ mol(-1), respectively, indicate that a physiosorption process occurred.

The acyltransferase (AT) domain in module 4 of the erythromycin polyketide synthase (PKS) was substituted with an AT domain from the rapamycin PKS module 2 in order to alter the substrate specificity from methylmalonyl-CoA to malonyl-CoA. The resulting strain produced 6-desmethyl erythromycin D as the predominant product. This AT domain swap completes the library of malonyl-CoA AT swaps on the erythromycin PKS and reinforces PKS engineering as a robust and generic tool.

Biosynthesis of polyketide antibiotics, such as erythromycin A (EA), can result in the formation of analogues of the main compound that are chemically and structurally extremely similar. The large-scale purification of these antibiotics by conventional high-performance liquid chromatography (HPLC) can be prohibitively expensive due to the large volume of both solvent and adsorbent required. This study examines the feasibility of using a novel pilot-scale countercurrent chromatography (CCC) machine as an alternative to HPLC. CCC is a low-pressure (typically <4000 kN m(-2)) liquid-liquid chromatographic technique that allows the separation of solutes on the basis of their partitioning between two immiscible liquid phases. The effects of mobile phase flow rate, column rotational speed, and sample injection volume on the attainable yield and purity of EA were investigated. Our results show that, at a mobile phase flow rate of 40 mL min(-1), a rotational speed of 1200 rpm, and an injection volume of 100 mL (10 g total erythromycin), EA could be satisfactorily fractionated with a purity of approximately 92% (w/w) and a recovery yield of approximately 100% (w/w). The total solute throughput was estimated to be 0.41 kg day(-1). More importantly, we demonstrated simple and predictive linear scale-up of the CCC separation based on data obtained from a single laboratory-scale CCC chromatogram, and verified this experimentally. The retention time and peak width of the target compound at the pilot scale could be predicted to within 4% for operation at a range of mobile-phase flow rates and injection volumes. This predictable nature of CCC separations, unlike HPLC methods, can greatly reduce process development times and enable a complete process-scale operating scenario to be planned., (Copyright 2003 Wiley Periodicals, Inc. Biotechnol Bioeng 81: 640-649, 2003.)

The new naturally occurring erythromycin G (4), formally derived from erythromycin B by hydroxylation of the C-16 methyl group, and 3-O-mycarosylerythronolide B (5), an erythromycin biosynthetic intermediate previously obtained only from microorganisms blocked in erythromycin biosynthesis, were isolated from a concentrate of mother liquors derived from a culture of Saccharopolyspora erythraea. The structure of erythromycin G was defined by spectroscopic data and X-ray crystallographic analysis. Theoretical calculation of 4 has been performed at MM2 level, and the low-energy conformations have been compared with X-ray data: both theoretical and experimental approaches give similar three-dimensional shapes. Antibacterial activity of 4 against both gram-positive and gram-negative organisms has been evaluated. A simple method for the isolation of large amounts of erythromycins B (2) and D is provided as well.

Three classes of macrolide resistance phenotypes and three different erythromycin resistance determinants were found among 127 erythromycin-resistant group A streptococcal (GAS) isolates recovered from 355 (35.8%) pediatric pharyngitis patients in Rome, Italy. According to emm and sof sequence typing results, erythromycin-resistant isolates comprised 11 different clonal types. Remarkably, 126 of the 127 macrolide-resistant isolates were serum opacity factor (sof) gene positive. These data suggest a strong association between macrolide resistance and the presence of sof among GAS isolates recovered from Italian pediatric pharyngitis patients.

Mutation and selection for increased resistance to cell-wall synthesis inhibitors led to alterations in the hyphal branching rate of Saccharopolyspora erythraea NRRL 2338. Mutants with decreased branching frequency exhibited increased hyphal strength (estimated by in vitro micromanipulation). As the hyphal strength was increased, this led to a greater proportion of hyphal particles in liquid culture with a hyphal fragment diameter of greater than 88 microm. This, in turn, coincided with proportionately increased antibiotic production., (Copyright 2002 Wiley Periodicals, Inc.)

Reactive extraction, permeation through liquid membranes and direct extraction are some of the new techniques applied for separation and advanced purification of biosynthetic antibiotics. Compared with the conventional separation techniques, the main advantages of these extraction methods are: high separation efficiency, the avoidance of antibiotics chemical and thermal inactivation, high purity of obtained antibiotics. Furthermore, using reactive extraction or permeation through liquid membrane, the antibiotics can be selective separated from their biosynthesis precursors or from the secondary biosynthetic compounds. This paper is a review on separation of Penicillins and Erythromycin by means of these extraction techniques, being underlined their advantages, applications and problems concerning the separation process scale-up.

Organic solvents are widely used in a range of multiphase bioprocess operations including the liquid-liquid extraction of antibiotics and two-phase biotransformation reactions. There are, however, considerable problems associated with the safe handling of these solvents which relate to their toxic and flammable nature. In this work we have shown for the first time that room-temperature ionic liquids, such as 1-butyl-3-methylimi- dazolium hexafluorophosphate, [bmim][PF(6)], can be successfully used in place of conventional solvents for the liquid-liquid extraction of erythromycin-A and for the Rhodococcus R312 catalyzed biotransformation of 1, 3-dicyanobenzene (1,3-DCB) in a liquid-liquid, two-phase system. Extraction of erythromycin with either butyl acetate or [bmim][PF(6)] showed that values of the equilibrium partition coefficient, K, up to 20-25 could be obtained for both extractants. The variation of K with the extraction pH was also similar in the pH range 5-9 though differed significantly at higher pH values. Biotransformation of 1,3-DCB in both water-toluene and water-[bmim][PF(6)] systems showed similar profiles for the conversion of 1,3-DCB initially to 3-cyanobenzamide and then 3-cyanobenzoic acid. The initial rate of 3-cyanobenzamide production in the water-[bmim][PF(6)] system was somewhat lower, however, due to the reduced rate of 1,3-DCB mass transfer from the more viscous [bmim] [PF(6)] phase. It was also shown that the specific activity of the biocatalyst in the water-[bmim] [PF(6)] system was almost an order of magnitude greater than in the water-toluene system which suggests that the rate of 3-cyanobenzamide production was limited by substrate mass transfer rather than the activity of the biocatalyst., (Copyright 2000 John Wiley & Sons, Inc.)

Separation and determination of erythromycin, spiramycin and oleandomycin by capillary zone electrophoresis coupled with fast reductive voltammetric detection using an Hg-film electrode was investigated in a simple aqueous phosphate buffer system. The influence of pH, concentration of phosphate, applied voltage, capillary length and dimension on the separation was examined and optimized. The entire separation of erythromycin, spiramycin, and oleandomycin was achieved in a 0.2 mol/L phosphate buffer system without organic modifiers. The electrochemical detection parameters, such as electrode material, applied waveform, scan rate, preconcentration potentials and preconcentration times, were investigated and discussed. This approach provides high separation efficiency and high sensitivity for all compounds, with detection limits (3 x peak-to-peak baseline noise) of 7.5 x 10(-8) mol/L for spiramycin, and 3 x 10(-7) mol/ L for erythromycin and oleandomycin. The calibration plot of peak areas for each separated peak vs. concentration of analyte was found to be linear over three orders of magnitude.

An official liquid chromatographic method for the analysis of erythromycin and related substances, which is based on a polymer reversed-phase, is described in the European Pharmacopoeia and in the United States Pharmacopeia. The pH of the mobile phase used in this system is 9.0. Recent advanced technology has led to the introduction of a new generation of silica-based reversed-phase column packings, which are claimed to be much more stable towards bases. They are useful for the analysis of basic compounds. Studies to verify the separation of erythromycin and related substances on Hypersil BDS C18, Luna C18(2), Inertsil ODS-2 and Supelcosil ABZ+ have been performed and the results are presented. It is shown that these base-deactivated phases give a better sensitivity and selectivity towards erythromycins than the polymer phase, provided that an adapted mobile phase is used. This is the first liquid chromatographic method described for the separation of erythromycin D from erythromycin A.

A critical limitation of electrospray ionization (ESI) liquid chromatography/mass spectrometry (LC/MS) sources is the susceptibility to blockage of interface orifices due to the deposition of involatile components from the sample and/or mobile phase. These components, including salts, buffers, and ion-pairing agents, can be essential to the performance of the chosen analytical method. We report here the performance enhancements provided by a novel atmospheric pressure ionization (API) source in the analysis of erythromycin A (ERY) using mobile phases that contain involatile components. The enhanced robustness of the new source is derived from the use of a continuous flow of aqueous solvent at the sampling cone orifice that maintains unobstructed ion transmission. The ESI mass spectral responses measured for ERY, using an LC separation that incorporates 10 mM sodium phosphate with and without 10 mM octane sulfonate, were monitored by repeated injections over 13-15 h total analysis time. Minimal effects on ESI mass spectral responses (integrated peak area) or chromatographic performance (peak shape, retention time) were observed during these studies. In the absence of the aqueous cleaning flow, complete loss of mass spectral responses and total blocking of the sampling cone was observed in less than 30 min. Responses for ERY spiked into chicken and beef liver, and catfish muscle at or below the regulatory level of interest (100 ppb), were quantified by internal standard calibration using this procedure. These results demonstrate the ability of a novel API-MS ion source to perform analyses that require the use of involatile mobile phase additives., (Copyright 2000 John Wiley & Sons, Ltd.)

A selective reversed phase liquid chromatography/mass spectrometry (LC/MS(n)) method is described for the identification of erythromycin impurities and related substances in commercial erythromycin samples. Mass spectral data are acquired on a LCQ ion trap mass spectrometer equipped with an electrospray interface operated in positive ion mode. The LCQ is ideally suited for identification of impurities and related substances because it provides on-line LC/MS(n) capability. Compared with UV detection, this hyphenated LC/MS(n) technique provides as a main advantage efficient identification of novel substances without time-consuming isolation and purification procedures. Using this method four novel related substances were identified in commercial samples., (Copyright 2000 John Wiley & Sons, Ltd.)

The separation of tylosin by micellar electrokinetic capillary chromatography with a mixed micelle system is described. Good selectivity was obtained with sodium phosphate buffer (80 mM, pH 7.5) containing 20 mM sodium cholate and 7 mM cetyltrimethylammonium bromide (CTAB). This method permits tylosin to be separated from its closely related substances within 15 min. The influences of type of buffer, buffer pH, the concentrations of sodium cholate and CTAB were investigated. The robustness of the method was examined for tylosin by means of a full-fraction factorial design. Quantitative results are presented. Using a similar buffer system (80 mM sodium phosphate, pH 6.0, 20 mM sodium cholate and 5 mM CTAB), separation of erythromycin and its main related substances was also obtained. However, detection sensitivity and resolution are not sufficient for analysis of related substances in erythromycin commercial samples.

In a previous report, a plasmid, pIG1, which contained the loading domain from the Streptomyces avermitilis polyketide synthase (PKS), promoters from Streptomyces coelicolor and the DEBS1-TE truncated PKS from Saccharopolyspora erythraea, was integrated into the S. erythraea chromosome, effectively replacing the natural erythromycin loading domain with the avermectin loading domain. In this paper, we report the feeding of short-chained fatty acids to this recombinant strain, and its parent, NRRL 2338. Both strains incorporated exogenously supplied fatty acids to produce novel, biologically active, C-13 substituted erythromycins.

Capillary electrophoresis (CE) provides high separation efficiency and thus is suitable for the analysis of complex mixtures of structurally similar compounds. The versatile nature of CE can be realised by controlling the chemistry of the inner capillary wall, by modifying the electrolyte composition and by altering the physicochemical properties of the analyte. A CE method has been developed for the separation of three macrolide antibiotics, erythromycin, oleandomycin and josamycin. A systematic approach was used to maximise analyte differential electrophoretic mobility by manipulating electrolyte pH, molarity and composition. In addition, some instrumental parameters such as capillary length and diameter and applied voltage were varied. The effect of the sample solvent and on-capillary concentrating techniques such as field amplified sample injection were investigated. Also, the influence of the injection of a water plug on the quantity of sample injected was demonstrated. The macrolides were completely resolved in less than 30 min in a 100 cm x 75 microm I.D. fused-silica uncoated capillary with a Z-shaped flow cell of path-length 3 mm. The analysis was performed in a 75 mM phosphate buffer (pH 7.5) with 50% (v/v) methanol and an applied voltage of 25 kV was selected to effect the separation.

A method was developed to separate, detect, and quantitate erythromycin (ERY) and tylosin (TYL) in animal feeds in the presence of 11 other drugs: 3 nitrofurans, 2 tetracycline antibiotics, 3 sulfonamides, 2 coccidiostats, and 1 antibacterial growth promoter. ERY and TYL were separated from coexisting drugs, detected by thin-layer chromatography, and quantitated microbiologically by an agar diffusion method. Analysis of 125 experimental animal feed samples fortified at 5 levels (7.5-400 ppm) with ERY and TYL and at 1 level (50 ppm) with the rest of the drugs gave limits of quantitation of 2 and 5 ppm, recoveries of 90.3 and 92.4%, and relative standard deviations of 4.3-7.3% and 3.6-6.1%, respectively.

Macrocyclic polyketides have been subjects of great interest in synthetic and biosynthetic chemistry because of their structural complexity and medicinal activities. With expression of the entire 6-deoxyerythronolide B synthase (DEBS) (10,283 amino acids) in a heterologous host, substantial quantities of 6-deoxyerythronolide B (6dEB), the aglycone of the macrolide antibiotic erythromycin, and 8,8a-deoxyoleandolide, a 14-membered lactone ring identical to 6dEB except for a methyl group side chain in place of an ethyl unit, were synthesized in Streptomyces coelicolor. The biosynthetic strategy utilizes a genetic approach that facilitates rapid structural manipulation of DEBS or other modular polyketide synthases (PKSs), including those found in actinomycetes with poorly developed genetic methods. From a technological viewpoint, this approach should allow the rational design of biosynthetic products and may eventually lead to the generation of diverse polyketide libraries by means of combinatorial cloning of naturally occurring and mutant PKS modules.

Sporeamicin A, a novel antibiotic, was isolated from the culture filtrate of an actinomycete. The producing organism, strain L53-18, was taxonomically assigned as a species of the genus Saccaropolyspora. The antibiotic was extracted with chloroform and was then purified by crystallization. It was obtained as colorless prisms from ethanolic solutions. Sporeamicin A exhibited a strong UV absorption peak at 276 nm. The molecular formula of sporeamicin A was determined to be C37H63NO12.