Search

Statement of problem When 3-dimensional printing casts, the operator can change the type of resin and the printing layer thickness, reducing the fabrication time. However, how these parameters affect the accuracy of 3-dimensionally printed casts is unknown. Purpose The purpose of this in vitro study was to evaluate the accuracy of 3-dimensionally printed casts by using a stereolithography (SLA) 3-dimensional printer (Forms2) with 3 different layer thickness (25, 50, and 100 μm) and 2 different resins (Gray and Cast) and by comparing the time to obtain each cast. Material and Methods One master cast was scanned, and a single file was printed several times. The printed casts were then scanned by using a laboratory scanner. The standard tessellation language (STL) files provided by the laboratory scanner were superimposed and compared by using a software program (Geomagic Control; 3D Systems). The 2-way ANOVA test was used for the trueness evaluation, followed by the Tukey test to identify differences among the groups (α=.05). Results No statistically significant differences in accuracy were found among the 3 different layers for either resin (P>.05). Printing time doubled as layer thickness decreased. Conclusions This study showed that when printing casts, the fastest printing settings can be used without losing accuracy and that the laboratory digital workflow can be accelerated with selection of the resin and cast layer, as the type of resin and layer thickness did not influence the quality of the casts.

The aim of this study was to assess the temporal evolution of external cervical resorption (ECR) defects using a volumetric quantification method.Cone-beam computed tomographic (CBCT) images of patients diagnosed with ECR who chose not to receive treatment and attended recalls were collected. ECR defects were segmented in CBCT images at baseline and recall, and their volumes were quantified. The volumetric ratio of resorption defects/teeth was calculated. Three-dimensional classification of defects at baseline and recall and the prevalence of root surface perforations ≥1 mm were determined. The Wilcoxon matched pairs signed rank test, chi-square test, and linear regression models were used to analyze the data.Fifteen patients with 20 teeth diagnosed with ECR and an average recall time of 21 months were included. Nine (45%) teeth showed a change in 3-dimensional classification at recall. The volume of resorption defects (P = .0001) and the volumetric ratio of resorption defects/teeth (P = .0001) increased over time. The prevalence of root surface perforations ≥1 mm was higher at recall (n = 17, 85%) compared with baseline (n = 9, 45%) (P = .008). Linear regression models showed significant associations between the resorption defect volume at recall compared with baseline (P .0001; 95% confidence interval, 0.053-0.081) and the volumetric ratio of resorption defects/teeth at recall compared with baseline (P .0001; 95% confidence interval, 0.205-0.356). There was no association between the volume of resorption defects at recall with the length of the recall period, sex, or age (P .05).When left untreated, ECR defects can increase in size and develop more root surface perforations. ECR has a dynamic nature, and its volumetric increase over time does not result from uniform/linear expansion of the defects.

Intraoral scanners (IOSs) have some inherent distortions caused by optical and/or software imperfections. However, how other factors such as operator experience, scan time, scanner type, and scan size influence scan accuracy is not clear.The purpose of this in vitro study was to evaluate the trueness and precision of scans performed by 3 professionals with different levels of experience by using 2 IOSs.Three operators with low, medium, and high levels of experience scanned a master model 10 times by using 2 IOSs (CEREC Omnicam; Dentsply Sirona and TRIOS 3; 3Shape), resulting in 10 standard tessellation language files for each group (N=60). Each standard tessellation language file was divided into 2 areas (prepared teeth and complete arch). Precision was evaluated by comparing the 10 scans from each examiner for each system. Trueness was evaluated by comparing each scan file with a reference scan obtained from a laboratory scanner (D2000; 3Shape). A 3D analysis software program (Geomagic Control; 3D Systems) was used to perform all the comparisons and superimpositions. The 3-way ANOVA test followed by the Tukey HSD test were used to assess precision and trueness. The 2-way ANOVA followed by the Tukey HSD test was used to assess scan time. The Pearson correlation test was performed between scan time and trueness for both scanners. An additional correlation was performed between scan time and number of images, as well as between number of images and trueness for the TRIOS 3.Statistically significant influences of operator (P.001), scanner (P.001), scan size (P.001), operator and scan size (P.001), and scanner and scan size (P.001) were observed. The TRIOS 3 group reported higher precision than the CEREC Omnicam group for complete-arch scans (P.001), although no difference was observed for scans of the prepared tooth. Medium- (P=.002) and low-experience operators (P.001) reported lower precision for complete-arch scans performed with CEREC Omnicam when compared with TRIOS 3. The low-experience operator reported significantly worse results for complete-arch scans in comparison with the medium- (P=.008 and P.001) and high-experience operators (P.001 and P=.001), by using TRIOS 3 and CEREC Omnicam, respectively. Medium- and high-experience operators reported similar results among themselves. The CEREC Omnicam scanner reported lower trueness for complete-arch scans when compared with the prepared tooth (P.001); for TRIOS 3, a difference was only observed for the low-experience operator when compared with the high-experience operator (P.001). The CEREC Omnicam reported lower trueness than the TRIOS 3, except for the medium-experience operator with the prepared tooth scan. Comparing the trueness between operators and considering the same scanner and scan size, all groups were similar. The low-experience operator had a longer scanning time than the medium- and high-experience operators. For TRIOS 3, the low-experience operator obtained the highest number of images during each scan.The accuracy of intraoral scans was influenced by operator experience, type of IOSs, and scan size. More experienced operators and smaller scan sizes made for more accurate scans. In addition, more experienced operators made faster scans, and the TRIOS 3 was more accurate than the CEREC Omnicam for complete-arch scans.

Objective Using a mouse osteoporotic model, this study aimed to determine the influence of hydrophilic titanium surfaces on gene expression and bone formation during the osseointegration process. Background Based on the previous evidence, it is plausible to assume that osteoporotic bone has a different potential of bone healing. Therefore, implant surface modification study that aims at enhancing bone formation to further improve short- and long-term clinical outcomes in osteoporosis is necessary. Material and methods Fifty female, 3-month-old mice were included in this study. Osteoporosis was induced by ovariectomy (OVX, test group) in 25 mice. The further 25 mice had ovaries exposed but not removed (SHAM, control group). Seven weeks following the ovariectomy procedures, one customized implant (0.7 × 8 mm) of each surface was placed in each femur for both groups. Implants had either a hydrophobic surface (SAE) or a hydrophilic treatment surface (SAE-HD). Calcium (Ca) and phosphorus (P) content was measured by energy-dispersive X-ray spectroscopy (EDS) after 7 days. The femurs were analyzed for bone-to-implant contact (BIC) and bone volume fraction (BV) by nano-computed tomography (nano-CT) after 14 and 28 days. Same specimens were further submitted to histological analysis. Additionally, after 3 and 7 days, implants were removed and cells were collected around the implant to access gene expression profile of key osteogenic (Runx2, Alp, Sp7, Bsp, Sost, Ocn) and inflammatory genes (IL-1β, IL-10, Tnf-α, and Nos2) by qRT-PCR assay. Statistical analysis was performed by ANOVA and paired t test with significance at P Results The amount of Ca and P deposited on the surface due to the mineralization process was higher for SAE-HD compared to SAE on the intra-group analysis. Nano-CT and histology revealed more BV and BIC for SAE-HD in SHAM and OVX groups compared to SAE. Analysis in OVX group showed that most genes (ie, ALP, Runx2) involved in the bone morphogenetic protein (BMP) signaling were significantly activated in the hydrophilic treatment. Conclusion Both surfaces were able to modulate bone responses toward osteoblast differentiation. SAE-HD presented a faster response in terms of bone formation and osteogenic gene expression compared to SAE. Hydrophilic surface in situations of osteoporosis seems to provide additional benefits in the early stages of osseointegration.

Made available in DSpace on 2022-04-28T19:46:04Z (GMT). No. of bitstreams: 0 Previous issue date: 2022-03-01 Academy of Osseointegration International Association for Dental Research National Institute of Arthritis and Musculoskeletal and Skin Diseases Endosseous implant surface topography directly affects adherent cell responses following implantation. The aim of this study was to examine the impact of nanoscale topographic modification of titanium implants on Osterix gene expression since this gene has been reported as key factor for bone formation. Titanium implants with smooth and nanoscale topographies were implanted in the femurs of Osterix-Cherry mice for 1–21 days. Implant integration was evaluated using scanning electron microscopy (SEM) to evaluate cell adhesion on implant surfaces, histology, and nanotomography (NanoCT) to observe and quantify the formed bone-to-implant interface, flow cytometry to quantify of Osterix expressing cells in adjacent tissues, and real-time PCR (qPCR) to quantify the osteoinductive and osteogenic gene expression of the implant-adherent cells. SEM revealed topography-dependent adhesion of cells at early timepoints. NanoCT demonstrated greater bone formation at nanoscale implants and interfacial osteogenesis was confirmed histologically at 7 and 14 days for both smooth and nanosurface implants. Flow cytometry revealed greater numbers of Osterix positive cells in femurs implanted with nanoscale versus smooth implants. Compared to smooth surface implants, nanoscale surface adherent cells expressed higher levels of Osterix (Osx), Alkaline phosphatase (Alp), Paired related homeobox (Prx1), Dentin matrix protein 1 (Dmp1), Bone sialoprotein (Bsp), and Osteocalcin (Ocn). In conclusion, nanoscale surface implants demonstrated greater bone formation associated with higher levels of Osterix expression over the 21-day healing period with direct evidence of surface-associated gene regulation involving a nanoscale-mediated osteoinductive pathway that utilizes Osterix to direct adherent cell osteoinduction. Department of Biosciences and Oral Diagnosis Institute of Science and Technology São Paulo State University (Unesp) Department of Oral Surgery and Integrated Clinics) School of Dentistry São Paulo State University (Unesp) Department of Comprehensive Dentistry School of Dental Medicine Case Western Reserve University Department of Biological and Material Sciences & Prosthodontics School of Dentistry University of Michigan Section of Periodontics School of Dentistry University of California Department of Orthopedic Surgery School of Medicine University of Michigan Department of Oral Biology College of Dentistry University of Illinois at Chicago Department of Biosciences and Oral Diagnosis Institute of Science and Technology São Paulo State University (Unesp) Department of Oral Surgery and Integrated Clinics) School of Dentistry São Paulo State University (Unesp) National Institute of Arthritis and Musculoskeletal and Skin Diseases: P30 AR069620

To evaluate and compare the accuracy of conventional and 3D-printed casts using five different 3D printers.In the control group (CG group, n = 5), five conventional impressions using light- and heavy-body polyvinyl siloxane were obtained from the master model, resulting in five stone models. In the test groups, five different scans were performed by a well-trained and experienced clinician using a TRIOS intraoral scanner. All data were exported as an STL file format, processed, and sent to five 3D printers. Five casts were manufactured in each group: SG (CARES P20, Straumann); FG (Form 2, Formlabs); WG (Duplicator 7, Wanhao); ZG (Zenith D, Zenith); and MG (Moonray S100, Moonray). Measurements of the accuracy (trueness and precision) of the casts obtained from conventional elastomeric impressions and 3D-printing methods were accomplished using a 3D analysis software (Geomagic Control).The FG group showed the lowest values for trueness (closer to real dimensions), which were similar to the SG group only (P.05). Groups MG, WG, and ZG presented higher values and were similar compared to each other. Data on precision demonstrated that all 3D-printed groups showed lower values for precision (smaller deviation) when compared to the control group.The trueness depends on the chosen 3D printer. All of the tested 3D printers were more precise than cast models obtained from conventional elastomeric impressions.

INTRODUCTION Patients with Class II subdivision malocclusion present skeletal and dental asymmetries. The purpose of this study is to assess those asymmetries by 3D mirroring and colormap quantification. METHODS This study analyzed 50 initial CBCTs divided in two groups: Class I (control group) and Class II subdivision (study group) malocclusion patients. CBCTs were oriented and full skull was segmented generating a 3D model. The right side of the 3D models was mirrored, using a midsagittal plane as reference, resulting in a perfectly symmetric skull based on two right sides. Original and mirrored models were superimposed on the unchanged right half, and differences were quantified using a colormap. Eight regions of interest were assessed: gonion, mandibular front, maxillary front, zygomatic process, maxillary and mandibular canine and molar areas. RESULTS Statistically significant differences using the Mann Whitney test were found in six of the eight evaluated areas when comparing the control to the study group. The maxillary areas did not show any difference between the groups. CONCLUSIONS Patients with Class II subdivision malocclusion show true skeletal and dental asymmetries when comparing right and left sides. The maxilla showed no significant skeletal asymmetry, but the maxillary teeth were positioned more mesially on the Class II side. The maxillary canine on the Class II side was also more bucally positioned. The mandible showed significant asymmetries with both skeletal and dental areas in the Class II side more distally and bucally positioned.

This study evaluated the microshear bond strength of a resin cement to Y-TZP after different methods of TiOnTiOEDS confirmed the presence of TiOHigh-pressure vacuum application of nTiOThe infiltration of TiO

Purpose To evaluate whether a hydrophilic surface treatment compared with a hydrophobic implant surface can enhance osseointegration by analysis of calcium deposition, bone-to-implant contact (BIC), bone volume (BV), and upregulation of genes involved in bone formation. Materials and methods Sixty implants (n = 60) with a hydrophobic (SAE) or hydrophilic (SAE-HD) surface treatment were placed bilaterally in each femur of 3-month-old male mice (n = 30). Scanning electron microscopy (SEM) and energy-dispersive x-ray spectroscopy (EDS) were utilized for quantifying the presence of calcium on the implant surface 7 days after implant placement. The specimens were analyzed after 14 and 21 days for BIC and BV by Nano CT scanning followed by histologic evaluation. Additionally, 1, 3, and 7 days postsurgery, femurs were harvested, implants were explanted, and gene expression (Sp7, Bsp, Sost, IL-1α, and IL-10) by quantitative real-time polymerase chain reaction was studied. Moreover, implants were characterized for surface roughness area. Data were statistically analyzed with two-way analysis of variance (ANOVA) followed by the Tukey test (P Results The amount of calcium on the surface was higher for SAE-HD after 7 days. Nano CT revealed significantly more BV in the SAE-HD than the SAE surface. The histologic assessment showed increased BIC in SAE-HD in comparison to SAE. SAEHD showed significantly increased levels of genes involved in bone formation. Conclusion Both surfaces were able to modulate bone responses toward osteoblast differentiation. SAE-HD presented a better response compared with SAE.

Background: Different sizes of arch could influence in digital methods to obtaining dental impressions and 3D models. The purpose of this study was to evaluate and compare the accuracy of two intra-oral scanners and conventional impression methods for the fabrication of working casts. Methods: Conventional impressions of a reference cast were obtained. Digital impressions were obtained with two intra-oral scanners: Cerec Omnicam (CO) and 3Shape Trios (ST). The obtained digital stereolithographic casts were printed on Zenith D 3D printer. The reference cast and fabricated casts were scanned with a bench top scanner and saved in STL format. All STL records were analyzed in specific software: complete arch (CA), partial arch (PA) and prepared teeth area (PT). One-way and two-way analyses of variance were performed to compare the accuracy, followed by the Tukey test. Results: No significant intergroup differences in trueness and precision were observed for the two intra-oral scanners. 3D printed casts had the lowest trueness when complete arch was analyzed and differed statistically from the stone cast. For complete arch precision, stone cast presented better results, however statistically different only from the CO. Conclusions: The two intraoral scanner systems had similar accuracy. Stone casts had higher trueness than 3D printed casts for CA. For CA precision, 3D printed cast presented similar results to the stone cast.

En Materials. Basilea (Suiza) : MDPI. Vol. 13, n. 8 (23 apr. 2020), art. 1967. e-ISSN 1996-1944. Este artículo se encuentra disponible en la siguiente URL: https://www.mdpi.com/1996-1944/13/8/1967 En este artículo de investigación también participan: Heber Isac Arbildo Vega y Monika Lukomska-Szymanska. The objective of this systematic review was to determine the influence of surface treatment of glass fiber posts on bond strength to dentine. Laboratory studies were searched in MEDLINE, PubMed, Embase, PubMed Central, Scopus, and Web of Science search engine. All authors interdependently screened all identified articles for eligibility. The included studies were assessed for bias. Because of the considerable heterogeneity of the studies, a meta-analysis was not possible. Twelve articles were found eligible and included in the review. An assessment of the risk of bias in the included studies provided a result that classified the studies as low, medium, and high risk of bias. The available evidence indicated that the coronal region of the root canal bonded better to the glass fiber post than apical regions. Phosphoric acid, hydrogen peroxide, and silane application enhance post’s retentiveness. In light of the current evidence, surface treatment strategies increase the bond strength of glass fiber post to dentine. However, recommendations for standardized testing methods and reporting of future clinical studies are required to maintain clinically relevant information and to understand the effects of various surface treatment of glass fiber post and their bond strength with dentine walls of the root canal.

Background The aim of the present study was to compare indirect methods to assess the clinical performance of pit and fissure sealants and validate the use of 3D scanners. Material and Methods Sample consisted of 58 plaster models of upper and lower first permanent molars, sealed with resin sealants, as well as photographs obtained during the 18-month follow-up. Pre-established criteria were applied to categorize the sealant presence/absence and marginal integrity. Two calibrated examiners performed the evaluations, independently, using Scanning Electron Microscopy (SEM; gold-standard), Photography, 3D (CEREC In Lab) and Stereomicroscope analysis. Results The intra-examiner Spearman correlation was 94% e 97%, respectively, and the inter-examiner was 96%. Data was submitted to Kappa test, Spearman correlation and Receiver Operating Characteristic Curve (ROC). 3D and SEM presented good concordance; Stereomicroscope showed regular concordance with SEM and 3D (p0.05). SEM had a significant positive correlation with 3D and Stereomicroscope (r=0.76 and 0.71, respectively; p

Information related to the optical and surface properties, including health compatibility, surface roughness, and esthetics, of 3D-printed dental materials is scarce.The purpose of this in vitro study was to compare the physical and surface properties of a 3D-printed resin with those of materials used for interim restorations.A 3D-printed resin (PR) (NextDent CB MFH; 3D Systems), an autopolymerizing interim material (BA) (Protemp 4; 3M ESPE), and a composite resin (Z350) (Filtek Z350XT; 3M ESPE) were tested for degree of color change (ΔE) (n=7) at different timepoints-24 hours after polishing/baseline (P0), 8 days after polishing (P1), and after artificial aging in water at 60 °C for 24 hours (P2)-by using a CIELab-based colorimeter; flexural strength (σ) (n=10) with a 3-point bend test; Knoop hardness (H) (n=8); and surface roughness (Ra) (n=7) with a profilometer. All specimens were polished 24 hours after polymerization, except for the additional group for surface roughness (BA) without polishing (BANP). A statistical analysis was performed by using 2-way repeated-measures ANOVA followed by the Fischer test for ΔE and 1-way ANOVA followed by the Fisher test for microhardness and surface roughness (α=.05).The Z350 showed the highest values for σ and H, followed by PR. BA showed the lowest results for both tests (P.05). Considering roughness, the Z350 showed similar values to those of BA but lower than PR; PR showed similar roughness when compared with BA. PR showed the highest color variation among the groups at all timepoints, followed by BA. The Z350 was the most color stable material at all timepoints.The 3D-printed composite resin had adequate mechanical and surface properties for an interim restorative material. It has the potential to be a low-cost workflow in dentistry, although its color stability could be a concern for long-term use.

The quality of the micromechanical retention between the enamel prisms exposed through acid etching and adhesive system can be influenced by the relationship between the angle of the exposed enamel prisms and the external surface/restorative material. Therefore, the aim of the present study was to determine the influence of the enamel cavosurface beveling in different cavity sizes on the angle relation between enamel prisms and the restorative material. For this research, 30 human permanent molars were used and divided into three groups according the isthmus aperture of class I cavities (1/4, 1/3, and 1/2 of the intercuspal distance). Cavosurface angle beveling was performed in each tooth buccal or palatal/lingual side, and a resin composite restoration was placed. Each restored tooth was sectioned in buccal/palatal direction followed by analysis in scanning electron microscope. Means of the angles observed between enamel prisms and the restorative material were registered and statistically analyzed by Kruskal-Wallis test. Results showed higher mean angle values for beveled groups when comparing with the values observed in the unbeveled margins (p < .05) regardless of the isthmus aperture, being 1/4 (beveled = 48.36°; unbeveled = 20.71°), 1/3 (beveled = 39.75°; unbeveled = 29.15°), and 1/2 (beveled = 37.02°; unbeveled = 26.34°). It was also observed that in some unbeveled cavities, there were the presence of laterally exposed enamel prisms (0°), mainly in more conservative cavities. It was concluded that the presence of higher angles values occurred in the samples with beveled margins, without presence of laterally exposed enamel prisms.

Purpose To evaluate the color change caused by post-irradiation conversion (ΔE24h and ΔE8 days) and artificial aging (ΔEAGING) of resin cements light activated through ceramics of different opacities immediately and 6 minutes after manipulating the material. Materials and Methods Resin cement disks (Allcem and LuxaCore) were light activated through ceramics (without ceramic, e.max HT, LT, and MO) immediately and 6 minutes after the manipulation (n = 10). Spectrophotometry was used to evaluate ΔE24h and ΔE8 days after 37˚C-dry-dark-storage for 24 hours and 8 days, and ΔEAGING after 60˚C-water-storage for 24 hours. Data were analyzed with three-way ANOVA and Tukey's HSD (α = 0.05). Results Regarding the post-irradiation color change, significant differences were found between the cements (p < 0.0001), light activation protocols (p = 0.037), and ceramics (p < 0.001). The immediate activation (16.2 ± 0.1) showed lower ΔE values than the delayed activation (16.5 ± 0.1). Ceramics influenced the ΔE values as follows: MO (14.0 ± 1.2) < LT (14.9 ± 1.2) ≈ HT (15.4 ± 1.2) < control (21.2 ± 1.2). Regarding ΔEAGING, significant differences were found between cements (p

Introduction: Due to its chemical, mechanical and biological properties, the glass ionomer cements (GIC) consist in one of the most versatile direct restorative materials, with many potential clinical indications, especially in the context of minimally invasive dentistry. Nevertheless, they have some limitations and require the knowledge of their characteristics and procedures of application in order to achieve their maximum potential. Objective: To demonstrate through literature review the main characteristics, indications, limitations and future perspectives for the use of GIC. Literature review: The database, such as Pubmed and Lilacs were used. Additionally, books were also evaluated and included. Conclusion: The GIC is in constant evolution and is one of the materials that are best suited in the context of preventive and conservative dentistry. It has satisfactory properties and versatility. On the other hand, presents inferior properties when compared to other direct restorative materials, requiring caution during its handling.

Fractures of the anterior teeth consists of a clinical condition that generates not only aesthetic and psychological problems, but may also cause dental pain. Thus, the affected teeth should be treated as urgencies in dental offices and their resolution whenever possible should be in a single session. Direct resin composite restorations should wherever possible be preferred due to the speed and possibility of obtaining good results. Objective: The objective of this case report is to describe the clinical sequence for restoration of a maxillary central incisor that presented a crown fracture using an immediate insert technique for resin composite (a "free hand" technique) with a modification to obtain dentin layer. Case report: A patient sought treatment after she fractured tooth #21. The restoration was performed with resin composite using the immediate technique. To facilitate the layering technique, the immediate insertion technique was changed for making the dentin lobes with the aid of a Teflon tape and the support with the index finger. Conclusion: The restoration of fractured anterior teeth can be performed quickly with the use of resin composites of different opacities and the use of the technique of immediate insertion proposed in this case report.

Dentin hypersensitivity treatments are based on the physical obliteration of the dentinal tubules to reduce hydraulic conductance. The aim of the present study is to evaluate the hydraulic conductance of bovine root dentin after irradiation with a 980-nm diode laser, with or without associated fluoride varnish.Sixty bovine root dentin specimens were divided into six groups (n = 10 in each group): G1, G3, and G5 (0.5 W, 0.7 W, and 1 W diode laser, respectively); G2, G4, and G6 (fluoride varnish application + 0.5 W, 0.7 W, and 1 W diode laser, respectively). The dentin hydraulic conductance was evaluated at four time periods with a fluxmeter: 1) with smear layer, 2) after 37% phosphoric acid etching, 3) after the treatments, and 4) after 6% citric acid challenge. After the dentinal fluid flow measurements, specimens were also evaluated for mineral composition using energy dispersive X-ray spectroscopy (EDS).Analysis demonstrated a better result with increased irradiation power (P0.001), especially if the diode laser irradiation was associated with the application of fluoride varnish (P0.001), ensuring a greater reduction in permeability. Considering the groups treated only with laser irradiation, the 1 W group was superior when compared with the 0.5 W and 0.7 W irradiated groups immediately after treatment (P0.001). After citric acid testing, all groups showed similar results, except when comparing the 1 W groups with the 0.5 W groups (P = 0.04). EDS results of the irradiated groups showed an increase in the proportion of calcium and phosphorus ions, which demonstrates a superficial composition modification after laser treatments.Laser irradiation of exposed dentin promoted significant reduction in the dentin hydraulic conductance, mainly with higher energy densities and association with fluoride varnish.

Statement of problem Resin-coating agents can be used to fill microstructural defects within composite resin restorations, which might result in a smoother surface. Nevertheless, data about the color stability and surface roughness of coated restorations are lacking. Purpose The purpose of this in vitro study was to compare the surface roughness and color stability of restorations before and after application of different resin-coating agents. Material and methods Forty specimens of composite resin (Filtek Z250) (diameter×height, 6×2 mm) were divided into 5 groups according to the surface treatments (n=8 per group): control (CTR), Fortify (FT), Lasting touch (LT), BisCover (BIS), and Fill Glaze (FG). The specimens were evaluated for surface roughness by using a profilometer with 3 readings for each specimen (separated by 300 μm) before immersion in a staining solution (coffee) and after 5 days immersed in coffee and for color stability (▵E) by using a spectrophotometer before being immersed in coffee (initial reading) and after 6 hours, 12 hours, 1, 2, 3, 4, and 5 days. Results Two-way ANOVA with repeated measures and the Tukey test showed that the CTR group showed the highest roughness values, similar to those of the FT and LT groups. The BIS and FG groups showed lower roughness than the other groups but similar results when compared with each other. All groups, except LT, showed increased roughness values after immersion in coffee solution, and the BIS group showed the lowest variation over time. Color alterations were found for all groups, with the CTR group showing the lowest ▵E values when compared with the other groups except for the BIS group. No correlation was found between surface roughness and degree of color change (P=.401). Conclusions The BisCover surface sealant showed the lowest surface roughness and the best color stability. Surface sealants can be used to fill microcracks and microgaps but should not be used as a substitute for polishing.

The achievement of predictable and long lasting adhesive restorations in posterior teeth have always been a major objective of studies in the context of materials and techniques development. The use of bulk fill composites could provide better outcomes, but it is important to assess their physico-mechanical properties, responsible for their clinical behavior. The purpose of the present study was to assess the mechanical and physical properties of bulk fill composites. The composites were divided into 2 groups according to their viscosity. For low viscosity composites, the present study assessed: Surefill SDR flow (SDR), X-tra Base (XB), Filtek Bulk Fill Flowable (FBF), and Filtek Z350XT Flow (Z3F- control); and for high viscosity composites: Tetric Evo Ceram Bulk Fill (TBF), X-tra Fil (XF), Filtek Bulk Fill (FBP), Admira Fusion x-tra (ADM) and Filtek Z350 XT (Z3XT- control). Composites were assessed through shrinkage stress test (using 12 and 24mm3 of composite in a custom device adapted in an Universal Testing Machine); volumetric shrinkage (using 64mm3 of composite placed on a Teflon mold and scanned in a micro computed tomography/CT); Youngs modulus (through a 3-point bending test device adapted in an Universal Testing Machine); microhardness and depth of cure tests (using longitudinal Knoop microhardness). All data was evaluated regarding their homogeneity using Shapiro-Wilk test. For polymerization stress, 3-way Variance Analysis (ANOVA) was used. Considering Volumetric Shrinkage, Youngs Modulus, Microhardness and Depth of Cure, one-way ANOVA was used. All ANOVA tests were followed by Tukeys test and 5% was adopted as significance level. Shrinkage stress test with 12mm3 showed SDR, TBF and XF generating the lowest stress after 300s, followed by other high viscosity composites (ADM, FBF, XB and FBP/Z3XT). The regular low viscosity composite (Z3F) generated the highest stress for all assessed times. Considering the same test, with 24mm3, after 300s, SDR, FBP and ADM generated similar stress, followed by TBF and XF. Low viscosity bulk fill composites generated lower stress than Z3F. Considering Youngs modulus, low viscosity composites (SDR, FBF, XB and Z3F) showed the lowest values, followed by ADM and TBF. The other high viscosity composites (Z3XT, FBP and XF) showed the highest values. For microhardness test, all low viscosity composites showed lower values (FBF being the lowest). For high viscosity composites, Z3XT showed the highest values, followed by XF, FBP/TBF and ADM. Assessing depth of cure, regular composites showed lower values when compared with bulk fill composites. All bulk fill composites showed adequate depth of cure over 4.5mm (microhardness 80% of initial reading). SDR and XB showed the highest depth of cure. All high viscosity bulk fill composites generated lower volumetric shrinkage than regular composites. All low viscosity bulk fill composites showed similar volumetric shrinkage when compared to the regular composites (Z3F and Z3XT). Bulk fill composites show characteristics that allow their use in larger increments (i.e. volumetric shrinkage and polymerization stress similar or lower when compared with regular composites). Nonetheless, the mechanical properties of bulk fill composites were widely variable, being important to individually assess each material previously to its clinical application. A obtenção de restaurações adesivas previsíveis e duradouras em dentes posteriores sempre foi objetivo de estudos na área de desenvolvimento de materiais e técnicas. O uso de resinas compostas do tipo bulk fill pode possibilitar melhores resultados, porém é importante o estudo de suas propriedades físico-mecânicas, responsáveis por seus comportamentos clínicos. O objetivo do presente estudo foi o de avaliar as propriedades físicas e mecânicas das resinas bulk fill. As resinas foram divididas em 2 grupos de acordo com sua viscosidade. Para resinas de baixa viscosidade, o presente estudo avaliou: Surefill SDR flow (SDR), X-tra Base (XB), Filtek Bulk Fill Flowable (FBF) e Filtek Z350XT Flow (Z3F-controle); e, para alta viscosidade: Tetric Evo Ceram Bulk Fill (TBF), X-tra Fil (XF), Filtek Bulk Fill (FBP), Admira Fusion x-tra (ADM) e Filtek Z350 XT (Z3XT-controle). As resinas foram avaliadas em relação à tensão de polimerização (utilizando 12 e 24mm3 de resina adaptadas em um dispositivo adaptado a uma máquina de testes universal); contração volumétrica (utilizando 64mm3 de resina composta inserida em um molde de Teflon e escaneada em um micro-tomógrafo/CT), modulo de Young (através de um dispositivo de flexão em 3 pontos adaptado a uma máquina de testes universal), microdureza e profundidade de polimerização (utilizando microdureza Knoop). Todos os resultados foram avaliados em relação à homogeneidade utilizando o teste de Shapiro-Wilk. Para avaliação da tensão de polimerização, foi empregada a Análise de Variância (ANOVA) a 3 critérios. Para as analyses de contração volumétrica, Módulo de Young, microdureza e profundidade de polimerizaçao, ANOVA a um critério foi empregada. Todas as Análises de Variância foram seguidas pelo teste de Tukey e 5% foi adotado como nível de significância. A tensão de polimerização com 12mm3 demonstrou que SDR, TBF e XF geraram valores significantemente mais baixos após 300s, seguidas por outras resinas de alta viscosidade (ADM, FBF, XB e FBP/Z3XT). A resina convencional de baixa viscosidade (Z3F) gerou valores de tensão significantemente mais elevados para todos os tempos avaliados. Considerando o mesmo teste, com 24mm3, após 300s, SDR, FBP e ADM geraram valores estatisticamente inferiores, seguidas por TBF e XF. As resinas bulk fill de baixa visocidade geraram menor tensão de polimerização que a Z3F. Considerando o modulo de Young, resinas de baixa viscosidade (SDR, FBF, XB e Z3F) apresentaram valores significantemente inferiores, seguidas por ADM e TBF. As outras resinas de alta viscosidade (Z3XT, FBP e XF) apresentaram valores significantemente mais elevados. Para o teste de microdureza, todas as resinas de baixa viscosidade apresentaram valores inferiores (FBF apresentou o menor). Para as resinas de alta viscosidade, Z3XT apresentou os valores mais elevados, seguida por XF, FBP/TBF e ADM. Para profundidade de polimerização, resinas compostas convencionais apresentaram valores signifixantemente mais baixos quando comparadas com resinas bulk fill. Todas as resinas bulk fill apresentaram profundidade de polimerização adequada até pelo menos 4,5mm (microdureza 80% da leitura inicial/superfície). SDR e XB apresentaram os valores mais altos de profundidade de polimerização. Todas as resinas bulk fill de alta viscosidade geraram menor contração volumétrica que resinas compostas convencionais. Todas as resinas bulk fill de baixa viscosidade apresentaram contração volumétrica similar às resinas convencionais (Z3F e Z3XT). Resinas compostas bulk fill apresentaram características que possibilitam sua indicação para serem empregadas em grandes incrementos (contração volumétrica e tensão de polimerização similar ou inferiores às resinas convencionais, além de maior profundidade de polimerização). No entanto, as propriedades mecânicas variaram grandemente entre as resinas estudadas sendo importante uma avaliação individual de cada material previamente ao seu uso clínico.

This study evaluated the wear of computer-aided design/computer-assisted manufacture (CAD/CAM) burs and the morphologic changes after a number of millings.Diamond burs (cylinder and step-bur) were divided into four milling groups: zero millings (G0); 15 millings (G1); 25 millings (G2); and 35 millings (G3). Seventy-five premolar crowns were milled using the Cerec Compact Milling unit and VitaBlock Mark II. Surface roughness, three-dimensional profile, and SEM were used for wear and surface damage evaluation.Two-way ANOVA and Tukey test (α = .05) showed that G3 produced statistically different values compared to G0 and G2, but not G1. The cylinder burs showed higher roughness values than step-burs for all groups. SEM showed similar diamond particle damage for cylinder burs and step-burs, and signs of surface damage, cracks, and particle losses for G3.Both cylinder burs and step-burs were able to sustain a larger number of milling procedures than indicated by the manufacturer.

Statement of problem A reliable and validated protocol for nondestructive analysis of the entire restorative interface that could be applicable in studies assessing the adaptation of direct and indirect restorations is lacking. Purpose The purpose of this in vitro study was to validate a 3D protocol for microleakage assessment in class II mesio-occluso-distal (MOD) cavities restored with composite resin. Material and methods Sixteen human third molars received standardized class II MOD preparations with cervical margins located 1 mm apical to the cemento-enamel junction. The specimens were restored with Filtek Bulk Fill Posterior (FBP) or Filtek Bulk Fill Flowable (FBF) and submitted to 10 000 thermocycles (5 °C and 55 °C with a 30-second dwell time at each temperature and 5-second transfer time). The specimens were scanned with microcomputed tomography (μCT) before and after immersion in 50% ammoniacal silver nitrate solution for 12 hours. Scanned data were processed, and the 3D amount of infiltrated silver nitrate was analyzed through the entire adhesive interface. In addition, the linear distance of silver nitrate infiltration was assessed using 3 axial images obtained from each specimen proximal box (2D analysis). Data were tested for homogeneity by using the Shapiro-Wilk test and evaluated by using 1-way ANOVA, followed by the post hoc Tukey HSD test (α=.05). Results FBP showed significantly lower leakage than FBF for both 2D and 3D analyses. A low correlation was observed between the assessment methods. Conclusions Three-dimensional analysis of microleakage using μCT is a predictable and more reliable method for nondestructive and comprehensive analysis of the entire specimen.

The use of hybrid-light (HL) during in-office teeth bleaching can provide faster and reliable results after a single bleaching session, especially if associated with previous acid etching. The present in vivo, interventional, split-mouth, triple-blinded and randomized study evaluated the efficiency of a HL, with and without prior enamel acid etching, assessing the gel application time, degree of color change, sensitivity and treatment stability up to 12 months.Thirty-four patients were selected and randomly divided into four groups. The color was evaluated using a spectrophotometer with the CIELab color system, and a VAS questionnaire was used to evaluate the sensitivity. Both upper and lower hemiarches (GI and III) received enamel acid etching with 37% phosphoric acid for 15 s prior to the application of 35% hydrogen peroxide gel (HP). For GI and II, HP was applied on both dental arches for 3-4 consecutive applications and activated by HL (2 × 3' activations with 1' interval); and 3 × 15' (HP) for GIII and IV without HL. Patients returned in 24 h, 1 week, 1-, 6- and 12-months intervals. The clinical operator was different from the clinical measurements operator.After 3-way ANOVA, Tukey's, Wilcoxon and Mann-Whitney tests, all with p 0.05, no statistical differences were observed between the groups regarding color change (ΔE) and sensitivity in all evaluations. The lowest gel application time was observed for GII (acid etch + HL), followed by GI (HL).The present study's results reveal the advantages of HL associated with acid etching prior to in office bleaching.

The purpose of this in vitro study was to compare the micro hardness, color stability/ΔE, and degree of conversion/DC of a resin cement light cured through different ceramic spacers. Lithium-disilicate ceramic samples were obtained from IPS E-max CAD blocks (HT A1) and IPS in-Ceram (transparent neutral); and divided in 7 groups (n = 8 for each test): CTR/control group; 06 M/0.6 mm monolithic; 12 M/1.2 mm monolithic; 20 M/2.0 mm monolithic; 06B/0.4 + 0.2 mm bilayered; 12B/1.0 + 0.2 mm bilayered; 20B/1.8 + 0.2 mm bilayered. The resin cement (Variolink veneer) was light cured through the ceramic spacers. The resin cement samples were evaluated for ΔE using a spectrophotometer after 24 h, 7days and after aging (24 h in water at 60 °C). Knoop microhardness and DC tests were conducted immediately after light curing, after 24 h and 7days. All experimental groups showed similar microhardness values, although being lower than CTR group. Similar results were observed after 7days. ΔE was similar between all groups after 24 h (except for 12B and 20B), and increased for all groups after 7days and after artificial aging, especially for thicker and bilayer groups. Only 06 M showed values similar to CTR group. DC values were similar to all groups immediately after light curing, increasing after 24 h and 7days. After 7days, only group 20B showed lower DC than CTR group. A tendency of higher DC could be observed for monolithic and thinner ceramics. All test results showed strong correlation (0.9987). Ceramic interposition can reduce mechanical and physical properties of resin cements, especially with thicker and bilayered ceramics. Group 06 M showed the best ΔE overtime.

Dentinal hypersensitivity consists in an increasing problem at dental offices and new approaches may be developed. Objectives: The authors studied different desensitizing treatments and their efficacy in reducing dentinal permeability and dentinal tubules opening. Material and methods: One hundred bovine incisors roots had their buccal surface flattened and treated by 3 applications of each desensitizing agent, following the respective groups (n = 10). After treated, 7 specimens of each group were prepared for a 0.5% basic fuchsin permeability test and the other 3 specimens were prepared to SEM qualitative analysis. The permeability test specimens were sectioned with a diamond saw in order to evaluate the stained and unstained areas. Kruskall Wallis statistical analysis was performed (p < 0.05). Results: Colgate Pró-Alívio paste and toothpaste, diode and Nd:YAG Lasers, GHF, Sensi Active, Oxagel and 2% Desensibilize promoted a significant permeability reduction when compared with the respective control groups (p < 0.05). Comparing the mean permeability differences between the different groups after the treatments, Oxagel and Nd:YAG were better than 0.2% Desensibilize group. Conclusion:None of the treatments may be considered 100% effective in treating dentinal hypersensitivity since a partial reduction of the permeability was observed.

Often, dentists perform procedures aiming at more esthetical than long-term clinical performance of restorations. Objective: To evaluate the prevalence of use of different direct and indirect restorative materials in posterior teeth. Material and methods: In 2004, a questionnaire was applied to 486 dentists living at five geographical regions of Brazil. The dentists answered a questionnaire containing four questions, in which they reported the most widely used restorative material for direct (amalgam, composite resin, and glass ionomer) and indirect restorations (gold, silver, and copper/aluminum alloys, indirect resin composites, and ceramics) and specified the reason for using the material type selected. Results: In 2004, amalgam was the direct restorative material most used by dentists at almost all regions, except from South region, where resin composite was the most used. Esthetics was the main reason stated for the use of resin composites. As for indirect restorations, metallic restorations were the most used in Northeast (77.8%). No differences were found regarding the material type use between metallic and aesthetic materials at North, Southeast and Center-West regions. At South region, esthetic restorations were the most used. Conclusion:Despite the limitations of this present study, direct and indirect metallic restorations were the most common materials in 2004.

Objective: Tooth bleaching tends to increase enamel roughness and porosity, in addition to reducing surface microhardness. The aim of this in vitro study was to evaluate the effects of bleaching treatments using different hydrogen peroxide (HP) concentrations, with and without light activation on bovine enamel microhardness. Materials and Methods: The buccal surfaces of sixty bovine incisors were flattened and polished and the enamel specimens were divided into six groups: G1: Control, exposed to artificial saliva; G2: 35% HP applied in two sessions (45’ each); G3: 35% HP applied in two sessions (3 × 15’ each); G4: 35% HP applied in one session (3 × 7’30”) plus hybrid light (HL); G5: 25% HP applied in one session (3 × 7’30”) plus HL; and G6: 15% HP applied in one session (3 × 7’30”) plus HL. After the treatment, the enamel specimens were stored in artificial saliva. The surface microhardness (Knoop) was measured at the baseline, 24 h and 7 days after bleaching. The data was analyzed using the ANOVA test, followed by the Tukey–Krummer test (P < 0.05). Results: All bleaching procedures lead to a decrease in surface microhardness when compared with the control group after 24 h. The lowest change in surface microhardness was found in the specimens treated with 15% HP plus HL. However, 35% HP plus HL induced the highest decrease in surface microhardness. After 7 days of remineralization, the surface microhardness returned to normal levels for all bleached specimens. Conclusion: Therefore, it can be concluded that the bleaching protocols caused a slight enamel surface alteration. However, the remineralization process minimized these effects.

Often, young patients (≤30 years old) present with carious lesions that progress acutely, compromising a large amount of tooth structure. In these cases, a treatment to prevent the occurrence of pulp exposure and promote remineralization of caries-affected dentin is necessary to maintain healthy dental structure and allow more conservative interventions. The approach will be different when pulp exposure occurs: The therapeutic treatments will be focused on reparative dentin formation and prevention of microorganisms penetrating the pulp organ. Due to the different possible treatments that can be performed to avoid pulp necrosis and the various materials that can be used for this purpose, professionals may have some difficulties understanding all the indications for conservative pulp treatments. The objective of this article is to describe and discuss a successful pulp capping and stepwise excavation associated with restorative treatment for deep caries lesions of anterior upper teeth.

To evaluate the color change caused by post-irradiation conversion (ΔEResin cement disks (Allcem and LuxaCore) were light activated through ceramics (without ceramic, e.max HT, LT, and MO) immediately and 6 minutes after the manipulation (n = 10). Spectrophotometry was used to evaluate ΔERegarding the post-irradiation color change, significant differences were found between the cements (p0.0001), light activation protocols (p = 0.037), and ceramics (p0.001). The immediate activation (16.2 ± 0.1) showed lower ΔE values than the delayed activation (16.5 ± 0.1). Ceramics influenced the ΔE values as follows: MO (14.0 ± 1.2)LT (14.9 ± 1.2) ≈ HT (15.4 ± 1.2)control (21.2 ± 1.2). Regarding ΔEThe delayed light activation resulted in increased color stability, while the ceramic interposition resulted in lower color stability.

The aim of this in vitro study was to evaluate the loss of tooth structure after cavity preparation for direct (retentive) and indirect (nonretentive) restorations and its relationship to the fracture strength of the prepared tooth. Sound human third molars (60 maxillary and 60 mandibular) were randomly assigned into 12 groups (n = 10) according to the type of cavity preparation and the respective buccolingual width. Class II mesio-occlusodistal cavity preparations, for both indirect inlay and direct resin restorations, were prepared with standardized dimensions of one-half, one-third, or one-quarter of the occlusal intercuspal distance. Fracture resistance was lower and weight loss was greater for all nonretentive preparations. Greater losses in weight and fracture resistance occurred when the buccolingual width for both types of cavities increased, except for the weight loss of the one-quarter and one-third indirect cavity preparations in the mandibular molars, and the fracture resistance of the one-half and one-third direct cavity preparations in maxillary molars. Higher tooth structure loss and lower fracture strength were recorded after preparation of the inlay cavities.

Os tratamentos que visam a remissão dos sintomas provocados pela hipersensibilidade dentinária são baseados na obliteração física dos túbulos dentinários com o objetivo de reduzir a condutibilidade hidráulica da dentina. Nesse contexto, diversos tratamentos têm sido avaliados, entre eles, a irradiação da superfície dentinária com laser. O objetivo do presente estudo foi avaliar a condutibilidade hidráulica da dentina radicular bovina, após irradiação com um laser de diodo (980nm), associado ou não com um verniz fluoretado. Sessenta espécimes de dentina radicular bovina com dimensões 5,5 X 5,5 X 1mm foram divididos em 6 grupos (n=10): Grupos 1, 3 e 5 (laser de diodo com 0,5; 0,7 e 1W respectivamente); Grupos 2, 4 e 6 (associação entre verniz fluoretado e laser de diodo com 0,5; 0,7 e 1W). A condutibilidade hidráulica da dentina, avaliada em FLODEC, foi analisada em 4 momentos: após criação da smear layer (permeabilidade mínima), após condicionamento com gel de ácido fosfórico a 37% (permeabilidade máxima), após os tratamentos propostos e após o desafio ácido com ácido cítrico a 6%. Os dados obtidos foram avaliados pela ANOVA a 2 critérios e teste de Tukey para comparação entre os diferentes grupos e ANOVA 1 critério de medidas repetidas e teste de Tukey para comparação entre as diferentes leituras dentro de cada grupo, sempre com p

This in vitro study aimed to analyze the effect of TiF(4) compared to NaF varnishes and solutions, to protect against dentin erosion associated with abrasion.Bovine dentin specimens were pre-treated with NaF-Duraphat (2.26% F), NaF/CaF(2)-Duofluorid (5.63% F), experimental-NaF (2.45% F), experimental-TiF(4) (2.45% F) and placebo varnishes; NaF (2.26% F) and TiF(4) (2.45% F) solutions. Controls remained untreated. The erosive pH cycling was performed using a soft drink (pH 2.6) 4 × 90 s/day and the toothbrushing-abrasion 2 × 10 s/day, in vitro for 5 days. Between the challenges, the specimens were exposed to artificial saliva. Dentin tissue loss was measured profilometrically (μm).ANOVA/Tukey's test showed that all fluoridated varnishes (Duraphat, 7.5 ± 1.1; Duofluorid, 6.8 ± 1.1; NaF, 7.2 ± 1.9; TiF(4), 6.5 ± 1.0) were able to significantly reduce dentin tissue loss (40.7% reduction compared to control) when compared to placebo varnish (11.2 ± 1.3), control (11.8 ± 1.7) and fluoridated (NaF, 9.9 ± 1.8; TiF(4), 10.3 ± 2.1) solutions (p0.0001), which in turn did not significantly differ from each other.All fluoridated varnishes, but not the solutions, had a similar performance and a good potential to reduce dentin tissue loss under mild erosive and abrasive conditions in vitro. Risk patients for erosion and abrasion, especially those with exposed dentin, should benefit from this clinical preventive measure. Further research has to confirm this promising result in the clinical situation.

The cementation of thin ceramic veneers employing fluid light-activated resin-based materials is a common procedure in the dental practice. Aim: To evaluate the influence of ceramic thickness and shade on the degree of conversion (DC) of a flowable light-activated material. Methods: flowable resin composite (Tetric N-Flow - shade A1) was light-activated through ceramic discs of two shades (IPS Classic - A1 and A3) in three thicknesses (0.5, 0.7 and 1.0 mm). For control, the resin composite was light-activated without ceramic interposition. DC was evaluated by FTIR (n=5). Data were analyzed by one-way ANOVA and Dunnett's T3 test (α=0.05). Results: Statistically significant differences between groups were observed (p

Introduction: Stone casts are used in dentistry to allow the confection of indirect restorations. Thus, gypsum dimensional stability is fundamental in order to achieve a precise fit between dental structure and restorative material. Objective: The purpose of the present study was to evaluate the hygroscopic linear expansion of commercially available gypsum products. Material and methods: Fifteen dental stones were analyzed (4 type II, 5 type III, 4 type IV and 2 type V), with n = 5. One hundred grams of each gypsum product were mixed following the respective manufacturers’ recommendations for powder/water ratio and poured into a V-shape mold, connected to an expansion-measuring device. The hygroscopic expansion was evaluated during 120 min and the collected data was converted into percentage and compared to initial dimensions of the specimen. Results: All type II and V dental stones showed expansion values compatible to the ADA and ISO recommendations. Considering type III stones, only Rutenium 3 was compatible with the recommendations. For type IV, only Durone IV showed expansion values higher than that recommended by ADA, but lower than that of ISO recommendations. Conclusion: The hygroscopic linear expansion of gypsum products should be periodically controlled in order to ensure their precision and reliability to dental practice.

Tele-health is more than an innovative alternative; it is an excellent tool that enables access to health and education in health, making it possible to minimize distances, optimize time and reduce costs. Based on these advantages, some Brazilian Universities have used these actions in strategies of education, research and extension, aiming at the application of Tele-health in Brazil. In that way, the Bauru School of Dentistry - University of Sao Paulo (FOB-USP) has applied the use of information and communication technologies in health by means of a "Tele-Health League" (TL), in order to diagnose, prevent and treat diseases, in addition to educate the population and health services. Objective: The present study aims to introduce the characteristics of the Tele-Health League of FOB-USP, as well as the development of its projects. Material and Methods: The Tele-Health League consisted as a Diffusion Course approved by the Provost of Culture and Academic Extension of the University of Sao Paulo. It is composed as a large group enclosing professoriate coordinator, academician principal, contributing professors and league members, those, diversified between undergraduates students, graduated, health employees, technology and information areas. The participant members are evaluated by the presence frequency (minimum of 85%), and by the performance of tests and paperwork about the theoretical content provided. Results: In four years of activities, the TLFOB-USP obtained a high satisfaction index (90%), an increased number of vacancies due to the interest to become a member, more commitment of the professors of the University and the accomplishment of association with other Brazilian leagues. It is emphasized that the approval percentage of the course results in approval from approximately half of its members. Also, it is important to identify and repair the causes related to the quitting of some members. Conclusions: The results showed that the TLFOB-USP members, adjoining to the professor's participants, develop projects in Tele-helth, in Tele-aid and Tele-education areas, thus resulting in the involvement of the University and the community.

Extensive restorations in posterior teeth always bring doubts to the clinicians regarding the best protocol, mainly when structures of reinforcement were lost. Objective This study aimed to evaluate the effect of beveling on the fracture resistance and pattern of class II (MOD) restored teeth. Methodology Ninety human premolars were randomly assigned into 9 groups: CTR (control/sound); NC (cavity preparation, non-restored); RU (restored, unbeveled); RTB (restored, entire angle beveling); RPB (restored, partial/occlusal beveling); EC (endodontic access/EA, non-restored); EU (EA, unbeveled); ETB (EA, entire angle beveling); EPB (EA, partial/occlusal beveling). Teeth were restored with Esthet X resin composite and stored in distilled water for 24 h before the inclusion in PVC cylinders. The axial loading tests were performed with 500 kgF at 0.5 mm/min crosshead speed until fracture of the specimens. Fracture resistance and pattern were accessed and data were analyzed using one-way ANOVA and Tukey’s HSD test (α=0.05). Results Mean (±SD) failure loads ranged from 136.56 (11.62) to 174.04 (43.5) kgF in the groups tested without endodontic access. For endodontically accessed teeth, fracture resistance ranged from 95.54 (13.05) to 126.51 (19.88) kgF. Beveling of the cavosurface angle promoted the highest fracture resistance values (p