Search

The pursuit of increasingly efficient and cost-effective solar energy solutions has driven significant advancements in photovoltaic (PV) technologies over the past decade. Among these innovations, bifacial solar cells, which capture sunlight from both the front and back surfaces, with front surface texturing and rear-side optimization playing crucial roles, present a promising avenue for enhancing efficiency compared to conventional designs. The effectiveness of these cells, however, is largely dependent on the optimization of rear surface properties and the material characteristics employed. This study investigates into the pivotal role of surface texture, particularly on silicon wafers, in shaping key performance metrics such as open-circuit voltage, short-circuit current, fill factor, and overall efficiency. Given the complex interdependencies among these parameters, machine learning (ML) tools, specifically random forest regression models, have been utilized to decode these intricate relationships. The findings underscore the significance of surface texture in modulating reflectance from both the rear and front surfaces, which in turn influences the overall performance of the solar cells. By applying ML models, this research provides an improved understanding of the impact of surface characteristics, thereby offering valuable insights into the optimization of design and material selection for next-generation high-performance solar cells. This ML optimization study indicates that the pyramid structures with a height of 3 μm and a base angle of 62° can significantly reduce reflectance to 9% while maximizing solar cell efficiency to 23.61%, marking a substantial advancement over existing designs. This model achieves 75% accuracy on synthetic test data and 78% on experimental data reinforcing model’s applicability despite typical ML limitations in PV systems. [ABSTRACT FROM AUTHOR]

This article proposes an optimization method to predictively model the perovskite solar cell with molybdenum disulfide (MoS2) based inorganic hole transport material (HTM) for improved fill factor (FF) and power conversion efficiency (PCE) by finding the most optimum thickness and donor/acceptor concentration for each layer via a hybrid L27 Taguchi grey relational analysis (GRA) based genetic algorithm (GA). Numerical simulation of the device is carried out by employing one-dimensional solar cell capacitance simulator (SCAPS-1D) while the optimization procedures are developed based on combination of multiple methods; L27 Taguchi orthogonal array, GRA, multiple linear regression (MLR), and GA. The results of post-optimization reveal that the most optimum layer parameters for improved FF and PCE are predicted as follows; SnO2F thickness (0.855 μm), SnO²F donor concentration (9.206×1018 cm-3), TiO2 thickness (0.011 μm), TiO2 donor concentration (9.306×1016 cm-3), CH3NH3PbI3 thickness (0.897 μm), CH3NH3PbI3 donor concentration (0.906×1013 cm-3), MoS² thickness (0.154 μm), and MoS2 acceptor concentration (9.373×1017 cm-3). Both FF and PCE of the device are improved by ~1.1% and ~12.6% compared to the pre-optimization. [ABSTRACT FROM AUTHOR]

[Display omitted] Chemical defects at the surface and grain boundaries of perovskite crystals cause deterioration of conversion efficiency and stability of perovskite solar cells (PSCs). In this study, a multifunctional additive, 5-fluoro-2-pyrimidine carbonitrile (FPDCN) molecule, is added into the perovskite precursor solution in order to passivate the uncoordinated Pb2+ by the cyanogen (–CN) group and pyrimidine N in FPDCN. Interestingly, fluorine (F) atoms interact with FA+ to form hydrogen bonds, which could regulate the perovskite crystallization process for the formation of high-quality perovskite crystals. Besides, the F atoms in FPDCN increase the water contact angle of perovskite films. As a result, the carrier extraction and transport in the perovskite film are significantly enhanced, and the non-radiative recombination is suppressed. The corresponding devices achieve a champion photovoltaic conversion efficiency (PCE) of 20.7 % and a fill factor (FF) of over 83 %. The device based on FPDCN shows long-term stability under a high-humidity atmospheric environment by maintaining 85 % of the initial efficiency after aging of 700 h in the glove box. This study provides a simple and convenient method to prepare stable and efficient PSCs by optimizing the perovskite precursor solution. [ABSTRACT FROM AUTHOR]

Perovskite solar cells (PSCs) possess high potential to generate electricity. As, hole transport material (HTM) is the main factor of concern so, in current study, with the purpose of improving power efficiency ratio of PSCs, a series of five novel molecules, namely DTP1, DTP2, DTP3, DTP4 and DTP5 have been created computationally by structural modifications of dithieno [3,2-b:2′,3′-d]pyrol cored (DTP-C6TH) HTM. Five different electron-deficient acceptor moieties are substituted at the peripheral sites of the reference molecule (DTP-C6TH). To predict the efficiency of these newly fabricated molecules, their optoelectronic characteristics have been investigated by using MPW1PW91 DFT approach coupled to the basis set 6-31G (d, p). All structures are optimized by executing same DFT method by frontier molecular orbitals (FMOs) evaluations has been performed which suggests an excellent charge transport rate in all fabricated molecules (DTP1-DTP5). Further, density of states was studied that describes the involvement of all segments of recently designed molecules in the synthesis of molecular orbitals HOMO and LUMO. Results illustrate the energy gap estimations pertaining formulated molecules are significantly reduced relative to reference molecule (2.99 eV) with sequence of DTP5 = 2.29 eV > DTP1 = 2.11 eV > DTP2 = 2.04 > DTP3 = 1.93 eV > DTP4 = 1.73 eV. Absorption spectrum has been analyzed and a red shift in the wavelength is perceived in all designed molecules (532–739 nm). Transition density matrix evaluations TDM, reorganizational energies (RE), open circuit voltage Voc and power conversion efficiency (PCE) for all architecture molecules have been computed and it is concluded from the outcomes that these newly planned molecules possess efficient opto-electronic properties with enhanced PCE of up to 24.3% and can be used in future as HTMs for application in Perovskite solar cells. [ABSTRACT FROM AUTHOR]

Reducing the content of light‐absorbing material in the active layer of semitransparent organic solar cells (ST‐OSCs) enhances the average visible transmittance (AVT) but sacrifices the power conversion efficiency (PCE). This dilemma is a key challenge to ST‐OSCs. Here trityl tetrakis(pentafluorophenyl) borate (TrTPFB)‐doping of the polymer donor at a suboptimal donor:acceptor (D:A) ratio is reported as an approach to enhance the light utilization efficiency (LUE) via boosting the fill factor (FF). The suboptimal D:A ratio results in not only a less efficient hole transporting network but also a narrower charge photogeneration profile. The latter widens the flat‐band region. These deteriorations make charge diffusion a crucial factor for compensating charge collection. TrTPFB‐doping mainly helps elongate the charge diffusion length to alleviate severe bimolecular recombination. As a result, the FF boosts from 65.1% to 72.2% in the film AVT increased device, which is comparable to that of the bulk heterojunction device with the optimal D:A ratio. The best LUE of 3.51% is achieved in the TrTPFB‐doped ST‐OSCs based on a ternary material combination; moreover, an LUE of 5.18% is predicted after proper optical optimization. The ST‐OSC showcases a greenhouse rooftop, which outperforms the glass one for the wheat plant. [ABSTRACT FROM AUTHOR]

The non‐wetting issue of the self‐assembled monolayer (SAM) layer can complicate subsequent perovskite deposition and impact device efficiency. This study addresses this challenge using a dual approach involving co‐self‐assembly and a buffer layer to enhance the wettability and interfacial contact of the buried perovskite film. A weakly acidic boronic acid derivative, 4‐N, N‐dimethylbenzeneboronic acid hydrochloride (4NPBA), is used to co‐self‐assemble with the regular SAM molecule on ITO and the subsequent FAI buffer layer further increased perovskite film coverage to 89%. This dual buried interface strategy—SAM‐4NPBA/FAI—results in a flat and dense perovskite interface. The optimized device demonstrates a high fill factor of 88.35%, a power conversion efficiency of 25.29%, and retains over 99% of its initial efficiency after 500 h of maximum power point testing. [ABSTRACT FROM AUTHOR]

This paper simulated the optimum solar cell power conversion efficiency-based planar solar surface morphology with various solar cell absorber structures. The spectral light intensity, reflected, absorbed, and transmission coefficients versus wavelength band spectrum varied from 300 nm to 1300 nm through the visible to near-infrared regions. The optimum solar cell performance parameters or key parameters are studied with different solar cell structure designs based on different surface contact and back contact layers. Cumulative generation current, cumulative electron–hole pair generation rate and electron–hole pair generation rate are clarified versus substrate depth for various solar cell structure designs. The absorbed current in substrate is optimized for various solar cell structure designs. Maximum power voltage and current are also optimized for the proposed solar cell structure design. The effective solar cell power efficiency is also demonstrated based on the optimized maximum power current and maximum power voltage. This study simulated the optimum solar cells power conversion efficiency based on planar solar surface morphology with various solar cells absorber structures. The spectral light intensity, reflection, absorption, and transmission coefficients versus wavelength band spectrum varied from 300 nm to 1300 nm. The optimum solar cell performance parameters or key parameters were studied with different solar cells structures design based on different surface contact and back contact layers. Cumulative generation current, cumulative electron-hole pairs generation rate and electron-hole pairs generation rate were clarified versus substrate depth for various solar cell structures design. The absorbed current in substrate is optimized for various solar cells structures design. Maximum power voltage and current were also optimized for the proposed solar cells designed structures. The effective solar cell power efficiency was also demonstrated based on the optimized maximum power current and maximum power voltage. [ABSTRACT FROM AUTHOR]

Antimony selenosulfide, denoted as Sb2(S,Se)3, has garnered attention as an eco-friendly semiconductor candidate for thin-film photovoltaics due to its light-absorbing properties. The power conversion efficiency (PCE) of Sb2(S,Se)3 solar cells has recently increased to 10.75%, but significant challenges persist, particularly in the areas of open-circuit voltage (Voc) losses and fill factor (FF) losses. This study delves into the theoretical relationship between Voc and FF, revealing that, under conditions of low Voc and FF, internal resistance has a more pronounced effect on FF compared to non-radiative recombination. To address Voc and FF losses effectively, a phased optimization strategy was devised and implemented, paving the way for Sb2(S,Se)3 solar cells with PCEs exceeding 20%. By optimizing internal resistance, the FF loss was reduced from 10.79% to 2.80%, increasing the PCE to 12.57%. Subsequently, modifying the band level at the interface resulted in an 18.75% increase in Voc, pushing the PCE above 15%. Furthermore, minimizing interface recombination reduced Voc loss to 0.45 V and FF loss to 0.96%, enabling the PCE to surpass 20%. Finally, by augmenting the absorber layer thickness to 600 nm, we fully utilized the light absorption potential of Sb2(S,Se)3, achieving an unprecedented PCE of 26.77%. This study pinpoints the key factors affecting Voc and FF losses in Sb2(S,Se)3 solar cells and outlines an optimization pathway that markedly improves device efficiency, providing a valuable reference for further development of high-performance photovoltaic applications. [ABSTRACT FROM AUTHOR]

Cu2(ZnSn)(S)4 (copper, zinc, tin, and sulfide (CZTS)) provides possible advantages over CuInGaSe2 for thin-film photovoltaic devices because it has a higher band gap. Preparing CZTS by electrodeposition because of its high productivity and lower processing costs, electroplating is appealing. Recently published studies reported that the electrodeposition process of CZTS still faces significant obstacles, such as the sulfur atomic ratio (about half of the whole alloy), deposits' adhesion, film quality, and optical properties. This work introduces an improved bath that facilitates the direct electroplating of CZTS from one processing step. The precursors used were significantly more diluted than the typical baths mentioned in the last few years. An extensive analysis of the electrochemical behavior at various rotation speeds is presented at room temperature (~22 °C). The deposited alloy's composition and adherence to the molybdenum back contact are examined with agitation. The annealing process was carried out in an environment containing sulfur, and the metal was not added at this stage. The ultimate sulfur composition was adjusted to 50.2%, about the desired atomic ratio. The compound's final composition was investigated using the Energy-Dispersive X-ray Spectroscopy technique. Finally, X-ray diffraction analysis was applied to analyze CZTS crystallography and to measure thickness. [ABSTRACT FROM AUTHOR]

A study work plan has been put up for methodical work in the field of solar energy photogalvanic (PG) cells. It was suggested and required to do experiments with PG cells in sunlight conditions. Improving the conversion of solar energy (SE) into electricity and storing it in PG cell is the goal of our study. Many characteristics of a PG cell with an MG+D-Xylose+Brij-35 system was investigated. The open circuit voltage (Voc), voltage at dark, photopotential (PP), and photocurrent (PC) recorded in this investigation are 1076.00 mV, 163.00 mV, 913.00 mV, and 673.00 μA, respectively. Through the adjustment of PG cells' numerous parameters, the effects of solar energy were investigated. Based on the aforementioned results, surfactant (Brij-35) have demonstrated through experimentation that they are an effective system and should be further investigated, particularly with regard to improving solar energy output and storage. [ABSTRACT FROM AUTHOR]

This work investigated a method for improving the efficiency of solar cells through the incorporation of carbon nanotubes (CNTs), which were used as the absorber layer of the solar cell. The CNTs were generated using plasma-enhanced chemical vapor deposition (PECVD). The use of the PECVD-generated CNTs in the absorber layer of the solar cell was found to increase the electrical conductivity due to the introduction of a large number of free charge carriers in the form of electrons and holes. We were thus able for the first time to estimate a relation between plasma variables and the efficiency of the proposed solar cell. The results showed that an increase in electron and ion density resulted in an increase in the efficiency of the solar cell, whereas an increase in electron and ion temperature led to a decrease in efficiency. We also studied the variation in efficiency in relation to the absorber layer of the proposed solar cell structure. The results obtained were consistent with those from previous studies based on solar cells. [ABSTRACT FROM AUTHOR]

Purpose: The purpose of this paper is to introduce the simple synthesis process of thermal-insulation coating by using three different nanoparticles, namely, nano-zinc oxide (ZnO), nano-tin dioxide (SnO2) and nano-titanium dioxide (TiO2), which can reduce the temperature of solar cells. Design/methodology/approach: The thermal-insulation coating is designed using sol-gel process. The aminopropyltriethoxysilane/methyltrimethoxysilane binder system improves the cross-linking between the hydroxyl groups, -OH of nanoparticles. The isopropyl alcohol is used as a solvent medium. The fabrication method is a dip-coating method. Findings: The prepared S1B1 coating (20 Wt.% of SnO2) exhibits high transparency and great thermal insulation property where the surface temperature of solar cells has been reduced by 13°C under 1,000 W/m2 irradiation after 1 h. Meanwhile, the Z1B2 coating (20 Wt.% of ZnO) reduced the temperature of solar cells by 7°C. On the other hand, the embedded nanoparticles have improved the fill factor of solar cells by 0.2 or 33.33%. Research limitations/implications: Findings provide a significant method for the development of thermal-insulation coating by a simple synthesis process and low-cost materials. Practical implications: The thermal-insulation coating is proposed to prevent exterior heat energy to the inside solar panel glass. At the same time, it can prevent excessive heating on the solar cell's surface, later improves the efficiency of solar cell. Originality/value: This study presents a the novel method to develop and compare the thermal-insulation coating by using various nanoparticles, namely, nano-TiO2, nano-SnO2 and nano-ZnO at different weight percentage. [ABSTRACT FROM AUTHOR]

The lead-free CH3NH3SnI3 perovskite is essential for absorbing light in perovskite solar cells (PSCs). In a photovoltaic (PV) device setup of FTO/STO/CH3NH3SnI3/Spiro-OMeTAD/Au, it demonstrates excellent PV performance. This device includes sulfur-doped tin oxide (STO) for the layer of electron transport (ETL), CH3NH3SnI3 as the absorber, and the hole transport layer (HTL) is Spiro-OMeTAD. The upper and back contacts consist of fluorine-doped tin oxide (FTO) and gold (Au), connecting these layers. Several parameters were estimated using the Solar Cell Capacitance Simulator (SCAPS-1D) program, including the thickness, acceptor and donor densities, series and shunt resistances, and temperature. The absorber, HTL, ETL, and FTO thicknesses were set at 1000 ​nm, 100 ​nm, 150 ​nm, and 50 ​nm, respectively, to find the perfect configuration. Densities of acceptors and donors were maintained at 1019 ​cm−3, 2.0 ​× ​1019 ​cm−3, 2.0 ​× ​1018 ​cm−3, and 1018 ​cm−3 for the absorber, HTL, ETL, and FTO, respectively, at an operating temperature of 300K. The device configuration exhibited reduced series resistance and increased shunt resistance, optimized with a back contact metal of Au. The idealized model demonstrated significant PV execution characteristics, including 1.117 ​V for open-circuit voltage (VOC), 28.88 ​mA/cm2 for short-circuit current density (JSC), 88.47 ​% for fill factor (FF), and 28.55 ​% for power conversion efficiency (PCE) under the AM1.5G spectrum. Additionally, the device displayed an average quantum efficiency (QE) of approximately 88.30 ​% at visible light wavelengths.

The article provides a detailed look at the fabrication of a high-performance structure for FASnI3-based perovskite solar cells (PSCs). The FTO/CeO2/FASnI3/CuI/Au structure is designed using the Solar Cell Capacitance Simulator in One Dimension (SCAPS-1D) to investigate the fabricated PSC's performance. This investigation's main objective is to improve PSCs performance by using non-traditional Hole transport layer (HTL) and Electron transport layer (ETL) materials, such as CeO2 and CuI, which have both been the subject of limited research. Moreover, the investigation seeks to determine the impact of several perovskite layer characteristics, including bandgap (Eg), electron affinity (χ), acceptor density (NA), thickness (t), and defect density (Nt). Additionally, this study also investigates the effect of various back contact work functions. Significant improvements in solar cell parameters, such as power conversion efficiency (PCE) from 22.06% to 24.87% and current density (Jsc) from 26.0274 to 30.675 mA/cm2, were observed by optimizing the device's parameters. In contrast, the fill factor (FF) and open circuit voltage (Voc) decreased their values from 86.13% to 87.10% and 0.9843 to 0.9308 V, respectively. These findings show that our designed solar cell structure performs better than those with conventionally used HTLs and ETLs. Consequently, this study highlights the potential benefits of lead-free PSCs and presents fresh opportunities for their development and use in various solar applications.

This study focuses on the fill factor (FF) measurement uncertainty contributing to the uncertainty in the labeling of the nominal maximum power (Pmax) of photovoltaic modules, which is determined under Standard Test Conditions (STC). Given that the price of these modules is tied to their Pmax, accurately quantifying the uncertainty of this measurement is crucial for ISO/IEC 17025 accredited laboratories. Adhering to the “Guide to the expression of uncertainty in measurement”, this work evaluates the uncertainty contribution of the Fill Factor (FF), a key parameter linking Pmax, the open-circuit voltage (Voc), and the short-circuit current (Isc). The analysis is based on data from three reference modules measured at the European Solar Test Installation (ESTI), part of the Joint Research Centre of the European Commission, since 1996. This data shows a reduction in FF uncertainty from approximately 0.6% to 0.3%, attributed to advancements in measurement technologies and techniques. Considering the goal of top calibration laboratories to measure Pmax with the lowest possible uncertainty, the improvement in FF uncertainty measurement is significant, ensuring more accurate labeling of photovoltaic modules.

This paper reports the fabrication and 60Co gamma radiation effects on the silicon heterojunction solar cells (SHJ). The SHJ solar cells were fabricated by using physical vapor deposition technique. An n-type Si wafer was used as a substrate. The intrinsic layer, hole selective layer and transparent conductive oxide were deposited above the substrate. A complete SHJ solar cell was fabricated in dimension of 1 × 1 cm2. The illuminated I–V characteristics of SHJ solar cell with A.M 1.5 are done using the solar simulator. The different electrical characteristics of solar cell such as short circuit current (Isc), open circuit voltage (Voc), fill factor (FF) and conversion efficiency (η) were studied. The fabricated SHJ solar cell displayed a conversion η of 9.09%, a Voc of 0.733 V, an Isc of 19.14 mA, and an FF of 64.74%. The fabricated SHJ solar cells are subjected to doses of 60Co gamma radiation ranging from 100 krad to 100 Mrad. As the gamma dose aincreased, the solar cell output parameters also reduced. FF decreased from 64.74 to 57.16%, and Voc decreased from 0.73 to 0.66 V. The Isc decreased to 7.825 from 19.14 mA. The η decreased from 9.09 to 2.98% for the fabricated silicon SHJ solar cell. [ABSTRACT FROM AUTHOR]

A world record conversion efficiency of 26.81% has been achieved recently by LONGi team on a solar cell with industry-grade silicon wafer (274 cm2, M6 size). An unparalleled high fill factor (FF) of up to 86.59% has also been certified in a separated device. The theoretical FF limit has been predicted to be 89.26%, while the practical FF is far below this limit for a prolonged interval due to the constraints of recombination (i.e., SRH recombination) and series resistance. The ideality factor (m) in the equivalent circuit of silicon solar cells is consistently ranging from 1 to 2 and rarely falls below 1, resulting in a relatively lower FF than 85%. Here, this work complements a systematic simulation study to demonstrate how to approach the FF limit in design of silicon solar cells. Firstly, a diode component with an ideality factor equal to 2/3 corresponding to Auger recombination is incorporated in the equivalent circuit for LONGi ultra-high FF solar cell; Secondly, an advanced equivalent circuit is put forward for comprehensive analysis of bulk recombination and surface recombination on the performance, in which specific ideality factors are directly correlated with various recombination mechanisms exhibiting explicit reverse saturation current density (J0). Finally, we evaluate precisely the route for approaching theoretical FF in practical solar cell fabrication based on electrical design parameters using the developed model. [ABSTRACT FROM AUTHOR]

In the field of organic photovoltaics (OPVs), significant progress has been made in tailoring molecular structures to enhance the open‐circuit voltage and the short‐circuit current density. However, there remains a crucial gap in the development of coordinated material design strategies focused on improving the fill factor (FF). Here, we introduce a molecular design strategy that incorporates electrostatic potential fluctuation to design organic photovoltaic materials. By reducing the fluctuation amplitude of IT‐4F, we synthesized a new acceptor named ITOC6‐4F. When using PBQx‐TF as a donor, the ITOC6‐4F‐based cell shows a markedly low recombination rate constant of 0.66×10−14 cm3 s−1 and demonstrates an outstanding FF of 0.816, both of which are new records for binary OPV cells. Also, we find that a small fluctuation amplitude could decrease the energetic disorder of OPV cells, reducing energy loss. Finally, the ITOC6‐4F‐based cell creates the highest efficiency of 16.0 % among medium‐gap OPV cells. Our work holds a vital implication for guiding the design of high‐performance OPV materials. [ABSTRACT FROM AUTHOR]

This work involved designing a solar cell with layers of fluorine-doped tin oxide, titanium dioxide, methylammonium tin bromide, and cuprous iodide. The impact of absorbent layer thicknesses ranging from 0.2 μm to 2.5 μm on developed PSC properties was examined. The thickness of the absorption layer that performs the optimally is discovered to be 0.2 μm. The synthetic solar cell provided an open circuit voltage of 1.07 V, a short circuit current of 34.356 mA/cm², an efficiency of 30.68%, and a fill factor of 83.404 at an optimal thickness of 0.2 μm. The findings proved the developed PSC's cost-effectiveness, increased environmental sustainability, and robustness compared to traditional counterparts. [ABSTRACT FROM AUTHOR]

One of the countries that constantly aim to develop a strategy for the exploitation of solar energy is Algeria, given the capabilities that make it a pioneer in this field. In this paper, we chose Oued El Keberit (OKP) Photovoltaic Plant located in the city of Souk-Ahras, eastern Algeria. The plant has a capacity of 15 MW. We focused on the solar panel array section of the station, specifically examining the performance of one of the subfields in this plant throughout the year under various outdoor conditions, beyond the Standard Test Conditions (STC) case. The study focused on factors that are known. Using a real data presented by the measurement station of the OKP photovoltaic power plant, numerical modeling and simulation of a PV station subfield were performed on the PV array for one subfield of the PV station using MATLAB Simulink. The results show how radiation intensity and temperature, whether low or high, affect the short-circuit current, open-circuit voltage, fill factor, and efficiency of the PV system. Notice that the level of radiation acts on the opposite of two important factors. The FF was at its lowest value in summer, but the efficiency is at its maximum value. Then, the FF in winter reaches its maximum, but efficiency is the lowest value. This means that they have an opposite relationship. On the other hand, the temperature affects the opposite way with open-circuit voltage especially when the temperature is above 25°C. [ABSTRACT FROM AUTHOR]

Continuous monitoring of large-scale solar photovoltaic (PV) installations is necessary to check the deterioration and monitor the performance of the PV plant. Fault diagnosis is crucial to ensure the PV plant operates safely and reliably. This paper presents a diagnosis methodology based on current-voltage (I-V) and PV characteristics to monitor and assess the behavior of solar PV. In this paper, I-V curve characterization using an I-V curve tracer is used to check the deterioration and diagnosis of the PV panels. The real-time performance of the 50.4 kWp rooftop solar grid interfaced PV plant is investigated and analyzed using I-V and PV curve tracers in real-time conditions. The overall performance of solar PV is assessed on a real-time test system in different scenarios such as variable climatic conditions, partial shading conditions, aging of solar panels, short circuit conditions, and dust decomposition. Furthermore, the performance assessment of solar PV is evaluated using performance indicators such as open circuit voltage index, short circuit current index, fill factor, and performance ratio. [ABSTRACT FROM AUTHOR]

Copyright of Iraqi Journal of Physics is the property of Republic of Iraq Ministry of Higher Education & Scientific Research (MOHESR) and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

In this paper, a novel structure of multilayer organic photovoltaic cell has been designed and simulated. The integration of Poly(3-hexylthiophene-2,5-diyl) (P3HT) buffer layer and Poly(9,9-bis(3’-(N,N-dimethyl) N- ethylammoinium propyl-2,7-fluorene)-alt-2,7-(9,9 dioctyl fluorene)) dibromide (PFN:BR) electron transport layer (ETL) in the proposed solar cell has improved the performance significantly. The various performance measuring parameters like power conversion efficiency (PCE), short circuit current (Jsc), open circuit voltage (Voc), fill factor (FF), quantum efficiency (QE) have improved significantly. Furthermore, the effect of different layer thickness, the density of traps $N_{t}$ and temperature on the proposed solar cell has been studied and the optimum value has been obtained. It has been observed that after optimizing the different parameters of the proposed structure, the performance measuring parameters shows an improvement of 14%, 33.3%, 200% and 300% in Voc FF, Jsc and PCE respectively over the reported organic solar cells. Further, a QE of about 90% is achieved in the proposed structure.

Optimization of optical and electrical properties of active semiconducting layers is required to enhance thin film solar cells' efficiency and consequently became the cornerstone for sustainable energy production. Computational studies are one of the ways forward to optimize solar cells’ characteristics. In this study, Silvaco-Atlas, a powerful software that excels in both 2D and 3D electrical simulations of semiconductors has been used for the simulation in order to investigate the solar cell properties. The architecture of the solar cell simulated was FTO/ZnO/In2S3/CuInS2/Mo. This study aims to optimize solar cell efficiency by optimizing film thicknesses and carrier concentrations via simulation. The designed solar cell was exposed to the presence of a sun spectrum of AM1.5 from a 1kW/m2 incident power density at 300K. The thickness values of the window (ZnO), absorber (CuInS2) and buffer (In2S3) layers were varied to record a solar cell's optimum thickness. The resulting FTO/ZnO/In2S3/CuInS2/Mo solar cell formed by simulation is presented. The best efficiency and fill factor of the solar cell simulated were found to be 41.67% and 89.19%, respectively. The recorded values of current density and the open circuit voltage of the cell were 40.33mA/cm2 and 1.15 V, respectively. Additionally, the maximum power of the simulated solar cell device was 41.68 mW. Optimization results revealed that the most efficient cell found was made up of a window layer with a thickness of 0.03μm, an absorber layer with a thickness of 6.0μm and a buffer layer with a thickness of 0.2μm. The optimized carrier concentration of ZnO, In2S3 and CuInS2 was respectively 1e21 cm-3, 1e20 cm-3, 3e18 cm-3 and the optimized Al-doped ZnO value was 1e25 cm-3. The Absorption spectra indicated that the solar cell's peak absorption occurs between 350 nm and 1250 nm and presented a good external quantum efficiency (EQE) of around 84.52% to 92.83% which indicates good efficiency in the visible domain. This performance is attributed to the transparency of FTO, ZnO and good absorption of In2S3 and CuInS2 thin films.

This study presents a strategy to increase the efficiency of dye-sensitized solar cells (DSSCs) by doping titanium dioxide (TiO2) with different magnesium (Mn) concentrations (1, 3, 5, 7, and 9%) generated by the sol-gel process and effectively employed as a photo-anode (the working electrode) for DSSCs. The Doctor Blade method coated the indium-doped tin oxide (ITO) glass with a thin film layer. X-ray diffraction (XRD) was used to evaluate the characteristics of undoped and manganese-doped TiO2, and the results demonstrate that all of the thin films are anatase. The samples were examined using XRD to assess grain size before and after Mn doping. The spectrum of UV-Vis absorption changes; accordingly, as doping increases, the energy gap decreases. The smallest energy gap's value (2.4 eV) is 7% manganese doping. AFM pictures show the average roughness and root mean square of the weight percentage of films doped with 5%. Field effect scanning electron microscope (FE-SEM) studies show that the particle size of thin films gets smaller as more Mn is added, which happens at least as much as 7% Mn doping. The optimal thickness for TiO2 paste over conductive glass is 15 μm, and the cell's power conversion efficiency increased to 0.604074% with an Imax of 4.965 mA, a Vmax of 0.488 V, and a fill factor (FF) of 68.45954%.

Partial shading is a prevalent phenomenon with a substantial impact on PV system performance. Various techniques, such as maximum power tracking (MPPT), PV module interconnection, and power electronics-based schemes, have been employed to address these challenges at both the module level and the submodule level. Existing methods face limitations related to the cost of hardware and the complexity of control systems. These limitations hinder the widespread application of current solutions. Also, Module-level techniques though simple and economical provide limited granularity. The choice between these techniques involves a trade-off between complexity, cost, adaptability, and the specific characteristics of the PV system and its operating environment.This paper presents a new hybrid submodule-level partial shading mitigation scheme based on TCT interconnection and differential power processing. The proposed system, emphasizing its role in enhancing overall PV system performance offers a cost-effective, and easy-to-control solution. To compare and validate the performance of proposed hybrid architecture, a practically installed single-phase grid tied central inverter 3 kW residential PV system is considered. This practical PV system is modified to hybrid architecture and the performance parameters such as power generation, mismatch power loss, fill factor, power conversion efficiency and power improvement calculated for different operating conditions. The results show that the modified conventional PV system mitigate the mismatch issue effectively and improves the output performance for any operating condition

Additively manufactured soft-magnetic components are inherently bulky leading to significant eddy current losses when applied to electrical machines. Prior works have addressed this issue by implementing structures based on the Hilbert space-filling curve which include eddy current suppressing gaps, thereby reducing the fill factor of the soft-magnetic component. The present research aims at investigating a number of space-filling curves in addition to sheets in order to find the optimal eddy current suppressing structure from an electromagnetic point of view. By means of both analysis and finite-element simulation, it was shown that sheets are superior at minimizing eddy current losses while space-filling curves excel at maximizing the fill factor. [ABSTRACT FROM AUTHOR]

The hybrid system of solar and wind is very useful in your day-to-day life. The various sources generally we are using likes sun energy, wave power generation, hydropower generation, tidewater power energy, and thermal gradient energy sources. This type of energy source is readily available in the environment and can consume maximum power from the actual solar panels and windmills. In this paper, we are using solar energy by using photovoltaic cells, and wind energy by using windmills generator. Solar and wind energy are cost-effective and easy to use. It can be used in mobile phones, Laptops, Daily Home appliances, and various types of lighting loads, which can be the best energy sources for urban, and rural, areas. As day by day, the electricity consumption is increased, because the demand has been increased day by day. We have to switch to other renewable energy sources and use the electricity from these sources. Power-Voltage and Current-Voltage characteristics of solar cell panels were accomplished at different values of irradiance and temperature levels of solar panels. [ABSTRACT FROM AUTHOR]

Performance studies of large area inverted organic photovoltaic (OPV) modules of configuration ITO/ZnO/PTB7-Th: PC71BM/MoO3/Ag are performed. At a laboratory of scale 0.06 cm2, this device configuration repeatedly demonstrates the power conversion efficiency (PCE) of ∼9%, which is within the range of PCE normally achieved for this configuration. The OPV modules with active area of 9.25 cm2 and 63 cm2 are fabricated employing spin coating techniques comprising a total area 25 cm2 (5 cm × 5 cm) and 144 cm2 (11 cm × 11 cm), respectively. The 25 cm2 module, composed of five cells connected in series show PCE of 3.256%, with short-circuit current (Jsc), open circuit voltage (Voc), and fill factor (FF), 3.210 mAcm−2, 3.20 V, and 31.719%. However, The 144 cm2 modules, composed of 10 cells connected in series show PCE 1.019, Jsc , Voc , and FF , 0.87 mAcm−2, 4.20 V, and 27.877%. The PCE dropped by 63.89% for modules of active area of 9.25 cm2 and 88.68% of modules of active area of 63 cm2. The PCE of the modules is decreased sharply due to loss in FF, and Jsc of the modules. These losses are exhibits due to quality of layer morphology, layer interfaces, and design of module. The PCE could be potentially improved up to the desired value by the further optimization of layer morphology, layer interfaces, design of module geometry, and film deposition/printing methods. The results showed that PTB7-Th: PC71BM is a splendid structure for future organic solar modules due to its high performance and compatibility with large area coatings. [ABSTRACT FROM AUTHOR]

Partial shadowing is the primary cause of power degradation in PV systems. There are various methods for harvesting extreme power from a PV array. Proper selection of PV array configuration is one of the strategies to extract maximum power. Cross ties in PV array configurations play a major role in maximizing the power. As the number of cross ties increases, maximum power from PV array increases. But, these cross ties have resistance, which increases the wiring losses, which may result in the decrease of power from the PV array. For the investigation of the impact of wiring resistance (column wiring and cross-ties wiring) under static and dynamic partial shading situations, this paper considers several 9×9 PV array designs such as Series-Parallel, Bridge-Link, Honey-Comb, Total-Cross-Tied, and Triple-Tied-Cross-Linked. The analysis of Total-Cross-Tied and Triple-Tied-Cross-Linked PV array configurations is extended to 18×18 array size. Measures such as global maximum power point, efficiency, fill factor, and mismatch losses were used in the performance analysis. The simulation findings show that, when a large number of panels are shaded statistically, the impact of wiring resistance is significant. [ABSTRACT FROM AUTHOR]