Search

Abstract Palladium nanoparticles display fascinating electronic, optical and catalytic properties, thus they can be used for various applications such as sensor fabrication. Conducting polymers such as polyaniline have also been widely used in sensor technology due to its cost effectiveness, versatility, and ease of synthesis. In this research, attention was given to unify the exceptional properties of these two materials and construct palladium nanoparticle coated polyaniline films to detect hydrogen and moisture. Electrochemical polymerization of aniline was carried out on gold sputtered epoxy resin boards. Polyaniline film was generated across a gap of 0.2 mm created by a scratch made on the gold coating prior to electrochemical polymerization. A palladium nanoparticle dispersion was prepared using sonochemical reduction method and coated on to polyaniline film using drop-drying technique. Polyaniline only films were also fabricated for comparative analysis. Sensitivity of films towards humidity and hydrogen was evaluated using impedance spectroscopy in the presence of the respective species. According to the results, polyaniline films exhibited an impedance drop in the presence of humidity and the response was significantly improved once palladium nanoparticles were incorporated. Interestingly, polyaniline only films did not respond to hydrogen. Nevertheless, palladium nanoparticle coated polyaniline films exhibited remarkable response towards hydrogen.

Mechanically robust alginate-based nanofibrous scaffolds were successfully fabricated by electrospinning method to mimic the natural extracellular matrix structure which benefits development and regeneration of tissues. Alginate-based nanofibres were electrospun from an alginate/poly(vinyl alcohol) (PVA) polyelectrolyte complex. SEM images revealed the spinnability of the complex composite nanofibrous scaffolds, showing randomly oriented, ultrafine, and virtually defects-free alginate-based/MgO nanofibrous scaffolds. Here, it is shown that an alginate/PVA complex scaffold, blended with near-spherical MgO nanoparticles (⌀ 45 nm) at a predetermined concentration (10% (w/w)), is electrospinnable to produce a complex composite nanofibrous scaffold with enhanced mechanical stability. For the comparison purpose, chemically cross-linked electrospun alginate-based scaffolds were also fabricated. Tensile test to rupture revealed the significant differences in the tensile strength and elastic modulus among the alginate scaffolds, alginate/MgO scaffolds, and cross-linked alginate scaffolds (P

We present a systematic study of the effects of post-fabrication annealing on the performance of photovoltaic devices that incorporate a photoactive donor–acceptor dispersed heterojunction system. Solar cells have been fabricated based on poly(3-octylthiophene) as donor (D) and single-wall carbon nanotubes as the electron acceptor (A) with a PEDOT:PSS hole transport layer. A post-fabrication annealing treatment was carried out at a temperature range of 40–200 C. The best results were obtained at 120 C; at this temperature the cell shows a short circuit current, Isc = 0.5 mA cm−2, an open circuit voltage, Voc = 0.75 V and a fill factor, FF = 0.6, resulting in a power conversion efficiency of η = 0.22% under AM 1.5 (100 mW cm−2) white light illumination. The annealing treatment led to a doubling of the power conversion efficiency. This was attributed to a better charge carrier transport in the polymer matrix and more effective charge separation and collection. [ABSTRACT FROM AUTHOR]

We report the direct measurement of electrical transport through rod-like polymer molecules, of poly(ethyl propiolate) (PEP), utilizing single walled carbon nanotubes (SWNTs) as electrodes. The electrical properties of the devices were measured (i) before cutting a SWNT, (ii) when a SWNT was cut and (iii) after PEP deposition into the nanoscale gap in a cut SWNT. The gate-dependent electrical properties showed a reduction in current from Ion = 2.4 x 10[?]7 A for SWNT devices to Ion = 3.6 x 10[?]9 A for PEP bridge devices, both with the ON/OFF ratio of 104. Similarly, metallic SWNT devices showed a reduction in current from a few hundreds of uA for a SWNT device to a few nA for a PEP-SWNT structure. The current density of a single PEP molecule is 105-106 A cm[?]2, which is relatively high, indicating that the PEP molecule can carry significant current. Use of SWNT electrodes was seen to be an effective method of contacting PEP nanorods to facilitate electrical measurements. [ABSTRACT FROM AUTHOR]

We examine the dark and the illuminated current-voltage (J-V) characteristics of poly(3-octylthiophene) (P3OT)/single-wall carbon nanotube (SWNT) composite photovoltaic cells as a function of SWNT concentration. Using an exponential band tail model, the influence of SWNT concentration on the J-V characteristics of the cells is analysed in terms of corresponding parameters such as effective hole mobility, short-circuit current, and open-circuit voltage. For the device with optimum 1% SWNT concentration, the increased photoresponse ([?]500 times) as compared to the pristine P3OT cell can be attributed partly to the increase ([?]50 times) in effective hole mobility, due to the reduction of localized states of the pristine P3OT matrix, and partly to the enhanced exciton extraction at the polymer/nanotube junctions. [ABSTRACT FROM AUTHOR]