Search

To alleviate the shock boundary layer interaction adverse effects, various active or passive flow control strategies have been investigated in the literature. This research sheds light on the behavior of perforated plates as passive flow control techniques applied to NACA0012 airfoils in cascade configurations. Two identical perforated plates with shallow cavities underneath are accommodated on the upper and lower surfaces of each airfoil in the cascade arrangement. Six different cascade arrangements, including a baseline configuration with no control applied, are additively manufactured, with different perforated plate orifice sizes in the range of 0.5–1.2 mm. A high-speed wind tunnel with Schlieren optical diagnosis and wall static pressure taps is used to investigate the changes in the shock waves pattern triggered by the perforated plates. Steady 3D density-based numerical simulations in Ansys FLUENT are conducted for further analysis and validation. In the cascade configuration, the perforated plates alter the shock structure, and the strong normal shock wave is replaced by a weaker X-type shock structure. Eventually, a 1% penalty in overall total pressure loss is induced by the perforated plates because of the negative loss balance between the reduced shock losses and the enhanced viscous losses. Further studies on perforated plate geometrical features are needed to improve this outcome in a cascade arrangement. [ABSTRACT FROM AUTHOR]

Understanding shock wave behavior in supersonic flow environments is critical for optimizing the aerodynamic performance of turbomachinery components. This study introduces a novel transonic linear cascade design, focusing on advanced blade manufacturing and experimental validation. Blades were 3D-printed using Inconel 625, enabling tight control over the geometry and surface quality, which were verified through extensive dimensional accuracy assessments and surface finish quality checks using coordinate measuring machines (CMMs). Numerical simulations were performed using Ansys CFX with an implicit pressure-based solver and high-order numerical schemes to accurately model the shock wave phenomena. To validate the simulations, experimental tests were conducted using Schlieren visualization, ensuring high fidelity in capturing the shock wave dynamics. A custom-designed test rig was commissioned to replicate the specific requirements of the cascade, enabling stable and repeatable testing conditions. Experiments were conducted at three different inlet pressures (0.7-bar, 0.8-bar, and 0.9-bar gauges) at a constant temperature of 21 °C. Results indicated that the shock wave intensity and position are highly sensitive to the inlet pressure, with higher pressures producing more intense and extensive shock waves. While the numerical simulations aligned broadly with the experimental observations, discrepancies at finer flow scales suggest the need for the further refinement of the computational models to capture detailed flow phenomena accurately. [ABSTRACT FROM AUTHOR]

Combustion through detonation marks an important leap in efficiency over standard deflagration methods. This research introduces a Pulsed Detonation Combustor (PDC) model that uses Hydrogen as fuel and Oxygen as an oxidizer, specifically targeting carbon-free combustion efforts. The PDC aerodynamic features boost operating cycle frequency and facilitate Deflagration-to-Detonation Transition (DDT) within distances less than 200 mm by means of Hartmann–Sprenger resonators and cross-flow fuel/oxidizer injection. The achievement of quality mixing in a short-time filling process represents not only higher cycle operation but also enhanced performances. The scope of this paper is to assess the impact of different fuel injectors with different opening areas on the performances of the PDC. This assessment, expressed as a function of the Equivalence Ratio (ER), is conducted using two primary methods. Instantaneous static pressures are recorded and processed to extract the maximum and average cycle pressure and characterize the pressure augmentation. Thrust measurements obtained using a load cell are averaged over the detonation cycle to calculate the time-averaged thrust. The specific impulse is subsequently determined based on these thrust measurements and the corresponding mass flow data. [ABSTRACT FROM AUTHOR]

Detonation combustion represents a significant advancement in efficiency over traditional deflagration methods. This paper presents a Pulsed Detonation Combustor (PDC) model that is designed with an aerodynamic mixing chamber featuring Hartmann–Sprenger resonators and crossflow injection. This design enhances operational cycle frequency and enables sustained detonation over short distances (below 200 mm). The PDC's performance was evaluated through a comprehensive full-factorial experimental campaign, incorporating four factors with four discrete levels each. Testing was conducted using both hydrogen/air and hydrogen/oxygen mixtures, highlighting the PDC's potential as a carbon-free combustion chamber suitable for both air-breathing and space-based propulsion systems. One advantage is the versatility of our PDC breadboard, which lies in its applicability to both terrestrial and in-space applications, such as interplanetary travel or trajectory corrections. Thrust measurements were recorded using a load cell and time-averaged thrust levels were determined over the detonation cycle and are reported herein, together with the specific impulse. The results underscore the PDC's promise as an efficient propulsion technology for future aerospace applications. [ABSTRACT FROM AUTHOR]

Featured Application: Design of linear cascades for high-speed bladed machinery. This paper presents the development of high-specific-speed mixed flow/centrifugal compressor vaned diffusers. Specifically, the design of a test rig that will make the visualization of shock waves on diffuser vanes manageable is addressed in the current study. In this particular case, linearization of an existing state-of-the-art compressor stage was used. For the computational modeling, a series of RANS analyses were conducted to examine the flow characteristics of the two cases explored: a complete transonic cascade and an idealized periodic passage. The distinct behavior exhibited by each vane passage within the entire cascade offers the opportunity to analyze the shockwave structures across a mass flow range of ±9% around the design point. Overall, the pressure coefficient distributions and flow field patterns appear to align with the single-passage conditions, although there are some minor lateral wall influences, particularly in the first passage close to the suction lateral wall. However, because of the nature of the flow, which is characterized by high velocity and density differences near the vanes, the equivalent mass flow per individual passage was difficult to estimate. This may also be attributed to the small endwall axial vortices; nonetheless, for the purposes of this paper, this was of little consequence. [ABSTRACT FROM AUTHOR]