Search

High-resolution Airborne Wide-band Camera (HAWC[Formula: see text]) is the facility far-infrared imager and polarimeter for SOFIA, NASA’s Stratospheric Observatory for Infrared Astronomy. It is designed to cover the portion of the infrared spectrum that is completely inaccessible to ground-based observatories and which is essential for studies of astronomical sources with temperatures between tens and hundreds of degrees Kelvin. Its ability to make polarimetric measurements of aligned dust grains provides a unique new capability for studying interstellar magnetic fields. HAWC[Formula: see text] began commissioning flights in April 2016 and was accepted as a facility instrument in early 2018. In this paper, we describe the instrument, its operational procedures, and its performance on the observatory.

Observations of the cosmic microwave background (CMB) provide a powerful tool for probing the evolution of the early universe. Specifically, precision measurement of the polarization of the CMB enables a direct test for cosmic inflation. A key technological element on the path to the measurement of this faint signal is the capability to produce large format arrays of background-limited detectors. We describe the electromagnetic design of feedhorn-coupled, TES-based sensors. Each linear orthogonal polarization from the feed horn is coupled to a superconducting microstrip line via a symmetric planar orthomode transducer (OMT). The symmetric OMT design allows for highly-symmetric beams with low cross-polarization over a wide bandwidth. In addition, this architecture enables a single microstrip filter to define the passband for each polarization. Care has been taken in the design to eliminate stray coupling paths to the absorbers. These detectors will be fielded in the Cosmology Large Angular Scale Surveyor (CLASS).

The 2 mm spectral range provides a unique terrestrial window enabling ground based observations of the earliest active dusty galaxies in the universe and thereby allowing a better constraint on the star formation rate in these objects. We have built GISMO (the Goddard-IRAM Superconducting 2-Millimeter Observer), a 2 mm, 128 element superconducting Transition Edge Sensor (TES) based bolometer camera for the IRAM 30 m telescope in Spain. The camera uses an 8×16 planar array of multiplexed TES bolometers, which incorporates our recently designed Backshort Under Grid (BUG) architecture, described elsewhere. The optical design incorporates a 100 mm (4 inches) diameter silicon lens cooled to 4 K, which provides the required fast beam of 0.9 λ/D. With this spatial sampling, GISMO will be very efficient at detecting sources serendipitously in large sky surveys, while the capability for diffraction-limited observations is preserved. With the background limited performance of the detectors, the camera provides significantly greater imaging sensitivity and mapping speed at this wavelength than has previously been possible. The major scientific driver for the instrument is to provide the IRAM 30 m telescope with the capability to rapidly observe galactic and extragalactic dust emission, in particular from high-z Ultra Luminous Infrared Galaxies (ULIRGs) and quasars, even in the summer season. The instrument will fill in the SEDs of high redshift galaxies at the Rayleigh-Jeans part of the dust emission spectrum, even at the highest redshifts. Our source count models predict that GISMO will serendipitously detect one galaxy every four hours on the blank sky, and that one quarter of these galaxies will be at a redshift of z 6.5. We expect to install GISMO at the 30 m telescope in the second half of 2007.

We describe a prototype detector system designed for precise measurements of Cosmic Microwave Background polarization. The design combines a quasi-optical polarization modulator, a metal feedhorn, a superconducting planar microwave circuit, and a pair of transition-edge sensor (TES) bolometers operating at

Two-dimensional MEMS microshutter arrays (MSA) have been fabricated at the NASA Goddard Space Flight Center (GSFC) for the James Webb Space Telescope (JWST) to enable cryogenic (~35 K) spectrographic astronomy measurements at near-infrared wavelengths. Functioning as a focal plane object selection device, the MSA is a 2D programmable aperture mask with fine resolution, high efficiency and high contrast. The MSA are close-packed silicon nitride shutters (cell size of 100 µm × 200 µm) patterned with a torsion flexure to allow their opening to 90°. A layer of magnetic material is deposited onto each shutter to permit magnetic actuation. Two electrodes are deposited, one onto each shutter and another onto the support structure side-wall, permitting electrostatic latching and 2D addressing. New techniques were developed to test MSA under mission-similar conditions (8 K ≤ T < 300 K). The 'magnetic rotisserie' has proven to be an excellent tool for rapid characterization of MSA. Tests conducted with the magnetic rotisserie method include accelerated cryogenic lifetesting of unpackaged 128 × 64 MSA and parallel measurement of the magneto-mechanical stiffness of shutters in 'pathfinder' test samples containing multiple MSA designs. Lifetest results indicate a logarithmic failure rate out to ~106 shutter actuations. These results have increased our understanding of failure mechanisms and provide a means to predict the overall reliability of MSA devices.

We describe the design, construction, and initial validation of the variable-delay polarization modulator (VPM) designed for the PIPER cosmic microwave background polarimeter. The VPM modulates between linear and circular polarization by introducing a variable phase delay between orthogonal linear polarizations. Each VPM has a diameter of 39 cm and is engineered to operate in a cryogenic environment (1.5 K). We describe the mechanical design and performance of the kinematic double-blade flexure and drive mechanism along with the construction of the high precision wire grid polarizers., Comment: 8 pages, 10 Figures, Submitted to Review of Scientific Instruments

We present multicolor images of Jupiter observed in the 350μm band with the first deployed astronomical instrument to use multiplexed superconducting bolometers. The Fabry–Perot Interferometer Bolometer Research Experiment (FIBRE) is a broadband submillimeter spectrometer that made these images in July 2004 at the Caltech Submillimeter Observatory (CSO). FIBREs detectors are superconducting bilayer transition edge sensor (TES) bolometers read out by a SQUID multiplexer. An order-sorted Fabry–Perot provides illumination of a 16-element linear bolometer array, resulting in five orders at a spectral resolution R of 1200 covering a band of 17 of the observed wavelength. The optics permit these orders to be scanned to cover the entirety of either the 350 or 450μm bands.

The design and validation of a dual polarization source for waveguide-coupled millimeter and sub-millimeter wave cryogenic sensors is presented. The thermal source is a waveguide mounted absorbing conical dielectric taper. The absorber is thermally isolated with a kinematic suspension that allows the guide to be heat sunk to the lowest bath temperature of the cryogenic system. This approach enables the thermal emission from the metallic waveguide walls to be subdominant to that from the source. The use of low thermal conductivity Kevlar threads for the kinematic mount effectively decouples the absorber from the sensor cold stage. Hence, the absorber can be heated to significantly higher temperatures than the sensor with negligible conductive loading. The kinematic suspension provides high mechanical repeatability and reliability with thermal cycling. A 33-50 GHz blackbody source demonstrates an emissivity of 0.999 over the full waveguide band where the dominant deviation from unity arrises from the waveguide ohmic loss. The observed thermal time constant of the source is 40 s when the absorber temperature is 15 K. The specific heat of the lossy dielectric MF-117 is well approximated by $C_v(T)=0.12\,T\,^{2.06}$ mJ g$^{-1}$ K$^{-1}$ between 3.5 K and 15 K.

The cosmic microwave background (CMB) provides a powerful tool for testing modern cosmology. In particular, if inflation has occurred, the associated gravitational waves would have imprinted a specific polarized pattern on the CMB. Measurement of this faint polarized signature requires large arrays of polarization-sensitive, background- limited detectors, and an unprecedented control over systematic effects associated with instrument design. To this end, the ground-based Cosmology Large Angular Scale Surveyor (CLASS) employs large-format, feedhorn- coupled, background-limited Transition-Edge Sensor (TES) bolometer arrays operating at 40, 90, and 150 GHz bands. The detector architecture has several enabling technologies. An on-chip symmetric planar orthomode transducer (OMT) is employed that allows for highly symmetric beams and low cross-polarization over a wide bandwidth. Furthermore, the quarter-wave backshort of the OMT is integrated using an innovative indium bump bonding process at the chip level that ensures minimum loss, maximum repeatability and performance uniformity across an array. Care has been taken to reduce stray light and on-chip leakage. In this paper, we report on the architecture and performance of the first prototype detectors for the 40 GHz focal plane.

This paper presents an end effector change-out mechanism (EECM) which embodies all the features and satisfies all the requirements necessary to perform zero-gravity robotic tool exchanges safely. Analysis of the mechanism has shown the exchange procedure to be sufficiently secure, and the latch mechanisms to have sufficient strength margins, to meet space flight requirements. Laboratory testing of the hardware has verified that the exchange procedure is secure and smooth, and has validated the operator feedback scheme. The final EECM design has proved so simple and easy to integrate that it is believed to have commercial potential.

The balloon-borne PIPER instrument will observe the polarization in the cosmic microwave background (CMB) at 200, 270, 350, and 600 GHz. Two co-pointed telescopes are placed inside a 3000 L liquid helium dewar and cooled to 1.5 K. The telescopes are arranged so that one measures Stokes parameters Q and V while the other measures U and V . Each telescope consists of a variable-delay polarization modulator (VPM) as the primary optical element, two off-axis mirrors, a folding flat, and re-imaging optics with off-axis lenses that focus each of the orthogonal linear polarization signals through an analyzer grid and onto two bolometer arrays (one for each polarization state). A cold Lyot stop is imaged onto the VPM to define the entrance pupil of the telescope. Each telescope has a 6° × 4.7° field-of-view.

We are constructing the Primordial Inflation Polarization Explorer (PIPER) to measure the polarization of the cosmic microwave background (CMB) and search for the imprint of gravity waves produced during an inflationary epoch in the early universe. The signal is faint and lies behind confusing foregrounds, both astrophysical and cosmological, and so many detectors are required to complete the measurement in a limited time. We will use four of our matured 1,280 pixel, high-filling-factor backshort-under-grid bolometer arrays for efficient operation at the PIPER CMB wavelengths. All four arrays observe at a common wavelength set by passband filters in the optical path. PIPER will fly four times to observe at wavelengths of 1500, 1100, 850, and 500 microns in order to separate CMB from foreground emission. The arrays employ leg-isolated superconducting transition edge sensor bolometers operated at 145 mK; tuned resonant backshorts for efficient optical coupling; and a second-generation superconducting quantum interference device multiplexer readout. We describe the design, development, and performance of PIPER bolometer array technology to achieve background-limited sensitivity for a cryogenic balloon-borne telescope.

One technique for mapping the polarization signature of the cosmic microwave background uses large, polarizing grids in reflection. We present the system requirements, the fabrication, assembly, and alignment procedures, and the test results for the polarizing grid component of a 50 cm clear aperture, Variable-delay Polarization Modulator (VPM). This grid is being built and tested at the Goddard Space Flight Center as part of the Polarimeter for Observing Inflationary Cosmology at the Reionization Epoch (POINCARE). VPMs modulate the polarized component of a radiation source by splitting the incoming beam into two orthogonal polarization components using a free-standing wire grid. The path length difference between these components is varied with a translating mirror, and then they are recombined. This precision instrumentation technique can be used to encode and demodulate the cosmic microwave background's polarization signature. For the demonstration instrument, 64 micrometer diameter tungsten wires are being assembled into a 200 pm pitch, free-standing wire grid with a 50 cm clear aperture, and an expected overall flatness better than 30 micrometers. A rectangular, aluminum stretching frame holds the wires with sufficient tension to achieve a minimum resonant frequency of 185 Hz, allowing VPM mirror translation frequencies of several Hz. A lightly loaded, flattening ring with a 50 cm inside diameter rests against the wires and brings them into accurate planarity.

We present first results of Hertz/VPM, the first submillimeter polarimeter employing the dual Variable-delay Polarization Modulator (dual-VPM). This device differs from previously used polarization modulators in that it operates in translation rather than mechanical rotation. We discuss the basic theory behind this device, and its potential advantages over the commonly used half wave plate (HWP). The dual-VPM was tested both at the Submillimeter Telescope Observatory (SMTO) and in the lab. In each case we present a detailed description of the setup. We discovered nonideal behavior in the system. This is at least in part due to properties of the VPM wire grids (diameter, spacing) employed in our experiment. Despite this, we found that the dual-VPM system is robust, operating with high efficiency and low instrumental polarization. This device is well suited for air and space-borne applications., Comment: 31 pages, 11 figures, 2 tables

Precise astronomical polarization measurements generally require the use of polarization modulation. We have developed a new modulator, the Variable-delay Polarization Modulator (VPM) which uses two modified Martin- Puplett interferometers to induce a physical path length difference between polarization components. This highly durable and efficient device can easily be adapted to a wide range of wavelengths and temperatures, making it well suited for air- and space-borne facilities. This paper discusses the basic modulator design and a comparison to the half-wave plate, as well as details of VPM tests conducted at the Submillimeter Telescope Observatory (SMTO).

We present images taken with the first deployed astronomical instrument to use multiplexed superconducting bolometers. The Fabry-Perot Interferometer Bolometer Research Experiment (FIBRE), a broadband submillimeter spectrometer, took these images as a detector investigation at the Caltech Submillimeter Observatory (CSO). FIBRE's detectors are superconducting bilayer transition edge sensor (TES) bolometers read out by a SQUID multiplexer. An order-sorted Fabry-Perot provides illumination of a 16-element linear bolometer array, resulting in five orders at a spectral resolution of around 1200 covering the 350 micron atmospheric band. We present multiwavelength images of Jupiter, Venus and the high-mass star-forming region G34.3+0.2 taken with this instrument at several wavelengths in the 350 micron band, separated by approximately 8 microns. These images have validated the use of multiplexed superconducting bolometers in an astronomical application and have helped inform the design of our future instruments.

We describe the design of the linear motion stage for a Variable-delay Polarization Modulator (VPM) and of a grid flattener that has been built and integrated into the Hertz ground-based, submillimeter polarimeter. VPMs allow the modulation of a polarized source by controlling the phase difference between two linear, orthogonal polarizations. The size of the gap between a mirror and a very flat polarizing grid determines the amount of the phase difference. This gap must be parallel to better than 1% of the wavelength. A novel, kinematic, flexure-based mechanism is described that passively maintains the parallelism of the mirror and the grid to 1.5 pm over a 150 mm diameter, with a 400 pm throw. A single piezoceramic actuator is used to modulate the gap, and a capacitive sensor provides position feedback for closed-loop control. A simple device that ensures the planarity of the polarizing grid is also described. Engineering results from the deployment of this device in the Hertz instrument April 2006 at the Submillimeter Telescope Observatory (SMTO) in Arizona are presented.

The Stratospheric Observatory For Infrared Astronomy's (SOFIA's) High resolution Airborne Wideband Camera (HAWC) will use an ion-implanted silicon bolometer array developed at NASA's Goddard Space Flight Center (GSFC). The GSFC Pop-Up Detectors (PUDs) use a unique "folding" technique to enable a 12 x 32 element close-packed array of bolometers with a filling factor greater than 95%. The HAWC detector uses a resistive metal film on silicon to provide frequency independent, ~50% absorption over the 40 - 300 micron band. The silicon bolometers are manufactured in 32-element rows within silicon frames using Micro Electro Mechanical Systems (MEMS) silicon etching techniques. The frames are then cut, "folded", and glued onto a metallized, ceramic, thermal bus "bar". Optical alignment using micrometer jigs ensures their uniformity and correct placement. The rows are then stacked side-by-side to create the final 12 x 32 element array. A kinematic Kevlar suspension system isolates the 200 mK bolometer cold stage from the rest of the 4K detector housing. GSFC - developed silicon bridge chips make electrical connection to the bolometers, while maintaining thermal isolation. The Junction Field Effect Transistor (JFET) preamplifiers for all the signal channels operate at 120 K, yet they are electrically connected and located in close proximity to the bolometers. The JFET module design provides sufficient thermal isolation and heat sinking for these, so that their heat is not detected by the bolometers. Preliminary engineering results from the flight detector dark test run are expected to be available in July 2004. This paper describes the array assembly and mechanical and thermal design of the HAWC detector and the JFET module.

The Fabry-Perot Interferometer Bolometer Research Experiment FIBRE, a protoype submillimeter spectrometer for astronomical observations, is based on a helium-cooled scanning Fabry-Perot and superconducting transition edge sensor bolometers (TES). The TES design takes advantage of a recently discovered method of excess noise reduction by depositing lateral normal metal bars on these devices. A SQUID multiplexer is used to read out the individual detector pixels. The spectral resolving power of the instrument is provided by a Fabry-Perot spectrometer. The outgoing light from the Fabry-Perot passes onto a low resolution grating for order sorting. A linear bolometer array consisting of 16 elements detects this dispersed light, capturing 5 orders simultaneously from one position on the sky. With tuning of the Fabry-Perot over one free spectral range, a spectrum covering Δλ/λ =1/7 at a resolution of ~1/1200 can be achieved. This spectral resolution is sufficient to resolve doppler broadened line emission from external galaxies. FIBRE operates in the 350 μm and 450 μm bands. These bands cover line emission from the important PDR tracers neutral carbon [CI] and carbon monoxide CO. The spectrometer is used at the Caltech Submillimeter Observatory for astronomical observations.

We describe the development, construction, and testing of two 384 element arrays of ion-implanted semiconducting cryogenic bolometers designed for use in far-infrared and submillimeter cameras. These two dimensional arrays are assembled from a number of 32 element linear arrays of monolithic Pop-Up bolometer Detectors (PUD) developed at NASA/Goddard Space Flight Center. PUD technology allows the construction of large, high filling factor, arrays that make efficient use of available focal plane area in far-infrared and submillimeter astronomical instruments. Such arrays can be used to provide a significant increase in mapping speed over smaller arrays. A prototype array has been delivered and integrated into a ground-based camera, the Submillimeter High Angular Resolution Camera (SHARC II), a facility instrument at the Caltech Submillimeter Observatory (CSO). A second array has recently been delivered for integration into the High-resolution Airborne Widebandwidth Camera (HAWC), a far-infrared imaging camera for the Stratospheric Observatory for Infrared Astronomy (SOFIA). HAWC is scheduled for commissioning in 2005.

We have been developing an architecture for producing large format, two-dimensional arrays of close-packedbolometers, which will enable far-infrared to millimeter wavelength ( l =100 mÐ2 mm) cameras and spectrometers toobtain images and spectra orders of magnitude faster than present instruments. The low backgrounds achieved in theseinstruments require very sensitive detectors with NEPs ranging from 10 Ð17 to 10 Ð19 W/ Hz. Superconducting transitionedge sensor bolometers can be close-packed using the Pop-Up Detector (PUD) format, and SQUID multiplexersoperating at the detector base temperature can be intimately coupled to them. The array unit cell is 8 ´ 32 pixels, using 32-element detector and multiplexer components. We have fabricated an engineering model array with this technologyfeaturing a very compact, modular approach for large format arrays. We report on the production of the 32-elementcomponents for the arrays. Planned instruments using this array architecture include the Submillimeter and Far-InfraRedExperiment (SAFIRE) on the SOFIA airborne observatory, the South Pole Imaging Fabry-Perot Interferometer (SPIFI)for the AST/RO observatory, the Millimeter Bolometer Camera for the Atacama Cosmology Telescope (MBC/ACT),and the Redshift O Z O Early Universe Spectrometer (ZEUS).Keywords: bolometer array, superconducting transition edge sensor, SQUID multiplexer, SOFIA, AST/RO, ACT

HAWC (High-resolution Airborne Wideband Camera) is a facility science instrument for SOFIA (StratosphericObservatory for Infrared Astronomy). It is a far-infrared camera designed for diffraction-limited imaging in fourspectral passbands centered at wavelengths of 53, 89, 155, and 216 m. Its detector is a 12x32 array of bolometerscooled to 0.2 K by an adiabatic demagnetization refrigerator. In this paper, we report on the development and testing ofthe instrument and its subsystems.Keywords : far-infrared, sub-millimeter, bolometer, instrumentation, cryogenic, camera, SOFIA 1. INTRODUCTION The requirements and design concepts for HAWC were discusse d in [1]. In this paper, we describe changes made sincethat time and report on progress in construction and testing of the instrumental subsystems. Major subsystems includedetector, optics, cryogenics, electronics, and software. We di scuss the fabrication and tes ting of the det ector separately[2][3]. This paper will focus on the other hardware subsystems. Software will be addressed in a future paper.The optical path and spectral passbands were described in [1]. Since that time, the optical design has remainedunchanged, but the filter passbands have been slightly modified (see Section 2.2 for band definitions andcharacteristics). Briefly, light from the telescope first passes through a warm fore-optics system. It reflects from a flatmirror, comes to a focus, then reflects from a spherical mirror that forms an image of the telescope at a cold pupil insidethe cryostat. From there, the light passes through one of four interchangeable lenses that re-image the telescope focalplane onto the detector array. Each lens assembly also contains a filter that defines the instrumental spectral response.The magnifications are such that there are 2.7 pixels per FWHM of the Airy function at each wavelength.The cryostat uses liquid helium and two vapor-cooled radiation shields to cool the optics and detector assembly to atemperature of ~4 K. An adiabatic demagnetization refrigerator (ADR) cools the detector array itself to 0.2 K. Thecryogenic suspension must be both thermally efficient and extremely stiff (to minimize microphonic noise andaccurately locate the optics under varying accelerations and orientations). The instrument must also meet Federal contact: al@oddjob.uchicago.edu ; telephone: (262)-245-5555; 373 W. Geneva St., Williams Bay, WI 53191

The High Resolution Airborne Wideband Camera (HAWC) and the Submillimeter And Far Infrared Experiment (SAFIRE) will use identical Adiabatic Demagnetization Refrigerators (ADR) to cool their detectors to 200mK and 100mK, respectively. In order to minimize thermal loads on the salt pill, a Kevlar® suspension system is used to hold it in place. An innovative, kinematic suspension system is presented. The suspension system is unique in that it consists of two parts that can be assembled and tensioned offline, and later bolted onto the salt pill.

The Submillimeter and Far-InfraRed Experiment (SAFIRE) on the SOFIA airborne observatory will employ a large-format, two-dimensional, close-packed bolometer array. SAFIRE is an imaging Fabry-Perot spectrometer operating at wavelengths between 100μm and 700μm. The array format is 16×32 pixels, using a 32-element multiplexer developed in part for this instrument. The low backgrounds achieved in spectroscopy require very sensitive detectors with NEPs of order 10 -19 W/√Hz. An architecture which permits 512 pixels to be placed adjacent to each other in an area the size of a postage stamp, integrate them with multiplexers, and provide all the necessary wiring interconnections is a complex proposition, but can be achieved. Superconducting detectors can be close-packed using the Pop-Up Detector (PUD) format, and SQUID multiplexers operating at the detector base temperature can be intimately coupled to them. The result is a compact array, easily scalable to kilopixel arrays. We describe the PUD architecture, superconducting transition edge sensor bolometers we have manufactured and tested using the PUD architecture, and the electronics of SQUID multiplexed readouts. We show the design and assembly of the mechanical model of a 512-element bolometer array.

We have built a prototype submillimeter spectrometer, FIBRE, which is based on a helium-cooled scanning Fabry-Perot and superconducting transition edge sensor bolometers (TES). SQUID multiplexers are used to read out the individual detector pixels. The spectral resolving power of the instrument is provided by the Fabry-Perot spectrometer. The outgoing light from the Fabry-Perot passes onto a low resolution grating for order sorting. A linear bolometer array consisting of 16 elements detects this dispersed light, capturing 5 orders simultaneously from one position on the sky. With tuning of the Fabry-Perot over one free spectral range, a spectrum covering Δλ/λ=1/7 at a resolution of ~1/1200 can be achieved. The spectral resolution is sufficient to resolve doppler broadened line emission from external galaxies. FIBRE operates in the 350 μm and 450 μm bands. These bands cover line emission from the important PDR tracers neutral carbon [CI] and carbon monoxide CO. The spectrometer was used at the Caltech Submillimeter Observatory to obtain the first ever astronomical observations using multiplexed arrays of superconducting transition edge bolometers.

SHARC II is a background-limited 350 micron and 450 micron facility camera for the Caltech Submillimeter Observatory undergoing commissioning in 2002. The key component of SHARC II is a 12 x 32 array of doped silicon 'pop-up' bolometers developed at NASA/Goddard. Each 1 mm x 1 mm pixel is coated with a 400 Omega/square bismuth film and located lambda/4 above a reflective backshort to achieve greater than 75% absorption efficiency. The pixels cover the focal plane with greater than 90% filling factor. At 350 microns, the SHARC II pixels are separated by 0.65 lambda/D. In contrast to the silicon bolometers in the predecessor of SHARC II, each doped thermistor occupies nearly the full area of the pixel, which lowers the 1/f knee of tile detector noise to less than 0.03 Hz, under load, at tile bath temperature of 0.36 K. The bolometers are AC-biased and read in 'total power' mode to take advantage of the improved stability. Each bolometer is biased through a custom approx. 130 MOmega CrSi load resistor at 7 K and read with a commercial JFET at 120 K. The JFETs and load resistors are integrated with the detectors into a single assembly to minimize microphonic noise. Electrical connection across the 0.36 K to 4 K and 4 K to 120 K temperature interfaces is accomplished with lithographed metal wires on dielectric substrates. In the best 25% of winter nights on Mauna Kea, SHARC II is expected to have an NEFD at 350 micron of 1 Jy Hz(sup -1/2) or better. The new camera should be at least 4 times faster at detecting known point sources and 30 times faster at mapping large areas compared to the prior instrument.

The High resolution Airborne Wideband Camera (HAWC) and the Submillimeter High Angular Resolution Camera II (SHARC II) will use almost identical versions of an ion-implanted silicon bolometer array developed at the National Aeronautics and Space Administration's Goddard Space Flight Center (GSFC). The GSFC "Pop-Up" Detectors (PUD's) use a unique folding technique to enable a 12 × 32-element close-packed array of bolometers with a filling factor greater than 95 percent. A kinematic Kevlar suspension system isolates the 200 mK bolometers from the helium bath temperature, and GSFC - developed silicon bridge chips make electrical connection to the bolometers, while maintaining thermal isolation. The JFET preamps operate at 120 K. Providing good thermal heat sinking for these, and keeping their conduction and radiation from reaching the nearby bolometers, is one of the principal design challenges encountered. Another interesting challenge is the preparation of the silicon bolometers. They are manufactured in 32-element, planar rows using Micro Electro Mechanical Systems (MEMS) semiconductor etching techniques, and then cut and folded onto a ceramic bar. Optical alignment using specialized jigs ensures their uniformity and correct placement. The rows are then stacked to create the 12 × 32-element array. Engineering results from the first light run of SHARC II at the Caltech Submillimeter Observatory (CSO) are presented.

We present performance results based on the first astronomical use of multiplexed superconducting bolometers. The Fabry-Perot Interferometer Bolometer Research Experiment (FIBRE) is a broadband submillimeter spectrometer that achieved first light in June 2001 at the Caltech Submillimeter Observatory (CSO). FIBRE'S detectors are superconducting transition edge sensor (TES) bolometers read out by a SQUID multiplexer. The Fabry-Perot uses a low resolution grating to order sort the incoming light. A linear bolometer array consisting of 16 elements detects this dispersed light, capturing 5 orders simultaneously from one position on the sky. With tuning of the Fabry-Perot over one free spectral range, a spectrum covering Δλ/λ= 1/7 at a resolution of δλ/λ ≈ 1/1200 can be acquired. This spectral resolution is sufficient to resolve Doppler-broadened line emission from external galaxies. FIBRE operates in the 350 µm and 450 µm bands. These bands cover line emission from the important star formation tracers neutral carbon [Cl] and carbon monoxide (CO). We have verified that the multiplexed bolometers are photon noise limited even with the low power present in moderate resolution spectrometry.

The SAFIRE, the Submillimeter and Far InfraRed Experiment, was designed for interstellar physics in the airborne Observatory SOFIA. SAFIRE is a cryogenic Echelle Grating spectrograph for covering 27 to 470 microns, with R ranging from 2-6,000. Here we will discuss the details of the optical design, the design process, and the performance of the instrument.