Search

This paper proposes a design criterion for calculating the resonant auxiliary elements of zero-voltage transition dc-dc pulsewidth-modulated (PWM) converters that use a dc auxiliary voltage source. The proposed criterion is based on stored energy in resonant auxiliary elements and takes into account the influence of the auxiliary voltage source value. Using this criterion, the reactive energy can be kept at a minimum level and a reduction of the auxiliary elements current ratings is achieved, which leads to lower conduction losses and improved converter efficiency. In addition, a reduction in size of auxiliary magnetic elements can be accomplished. To illustrate the usefulness of the proposed design criterion, the paper compares results obtained from the True-PWM Zero-Voltage Switching pole boost converter designed according to the proposed criterion, and from the original design guidelines. Experimental results show an efficiency gain of about 1% for a wide load range and 1.5% at full load. In addition, a reduction of about 52% in the auxiliary transformer volume for the implemented prototype was achieved, ensuring a reduction in overall converter size. Experimental results were obtained using a 1-kW 100-kHz laboratory prototype. Index Terms--DC-DC power conversion, pulsewidth-modulated (PWM) power converters, switching circuits.

This paper presents a universal auxiliary commutation cell for pulse-width modulated (PWM) inverters termed zero current and zero voltage transition (ZCZVT) commutation cell. It provides zero current and zero voltage commutation, simultaneously, during main power devices turn-on and turn-off, with controlled di/dt and dv/dt. As a result, commutations of the main power devices occur without any losses. This unique characteristic is not achieved by any other soft-switching commutation cell for inverters hitherto presented in the literature, making it a strong candidate for use in low-power (MOSFET), medium-power (IGBT) or high-power applications (GTO, thyristor). Furthermore, reverse recovery losses of main diodes are minimized and auxiliary switches commutate at zero current. To demonstrate the operation of the proposed universal auxiliary commutation cell, a ZCZVT PWM Full-Bridge inverter is analyzed. To evaluate the operation of the auxiliary circuit in different conditions, prototypes with both IGBTs and MOSFETs for different output powers levels were implemented and their performances compared. Experimental results confirm that there is no overlap between main switch current and voltage, and that waveform ringing is practically eliminated. Index Terms--Inverters, soft-transition, ZCZVT.

This paper presents a new isolated dc-dc zero-voltage-switching (ZVS) converter, which is composed of two half-bridge converters associated in series operating at constant frequency. The converter can be seen as an alternative to the ZVS-phase-shift full-bridge dc-dc converter for high-voltage applications. The paper proposes a new command strategy, named interleaved phase shift, which allows equalization of the input capacitor voltage, where each capacitor shares one-quarter of the total input voltage. Due to phase-shift modulation, the current is equally shared among main switches, reducing the converter conduction losses, when compared with conventional pulsewidth modulation. Furthermore, the input capacitors voltage oscillations are reduced due to load variations, as well as due to input dc-bus 120-Hz ripple. Just as with a ZVS-phase-shift full-bridge converter, the proposed converter achieves ZVS in a wide load range, as a function of the transformer leakage inductance. The paper describes the analysis, operating principles, and design procedure for the proposed converter. Experimental results from a 1.5-kW prototype converter operating at 100 kHz with isolated 60-V/25-A output are presented to validate the theoretical analysis and to demonstrate the performance of the proposed converter. Index Terms--DC-DC converters, multilevel converters, power supply, soft switching.

This paper presents a model reference controller with a repetitive control action for uninterruptible power supply (UPS) applications. The model reference controller modifies the structure of the plant so that the closed-loop transfer function is equal to a chosen reference model transfer function, whereas the repetitive control action minimizes periodic distortions caused by unknown periodic disturbances. Design procedure and stability analysis of the control scheme are discussed. Simulation and experimental results for a single-phase PWM inverter (110 [V.sub.RMS], 1 kVA) controlled by a low cost microcontroller are presented to verify the performance of the proposed control approach under different load conditions. Index Terms--Digital control, uninterruptible power supplies, voltage-source PWM inverters.

This paper presents a comparison among digital control techniques with repetitive integral action applied to voltage-source PWM inverters. As a result of the repetitive integral action, these digital control schemes can reduce steady-state errors and distortions caused by unknown periodic disturbances, which usually result from the input source and output load. Moreover, these digital control schemes measure only the output voltage, decreasing the amount of sensors and the overall system cost. The control laws, stability analysis, common and distinguishing features of these control algorithms are discussed. Experimental results from a PWM inverter (110 [V.sub.RMS], 1 kVA) controlled by a low cost microcontroller are presented to demonstrate the control techniques performance under different load conditions, output filters and command strategies. Index Terms--Digital control, repetitive control, uninterruptible power supplies, voltage-source PWM inverters.

This article presents a discrete‐time robust model reference adaptive controller and adaptive sigmoid super‐twisting sliding mode (RMRAC‐ASSTSM) and its stability analysis using Lyapunov stability theory. This control structure is robust to matched and unmatched dynamics. In addition, the chattering phenomenon tends to be suppressed in the steady state due to adaptive super‐twisting sliding mode action using a sigmoid function. The performance of the proposed control structure is corroborated with simulation results, considering a second‐order non‐minimum phase unstable plant, where it can be seen that RMRAC‐ASSTSM regulation errors converge to a finite residual set when the plant presents unmodeled dynamics. A comparison is also presented with a similar RMRAC‐based control structure with an adaptive super‐twisting sliding mode implemented with a sign function. [ABSTRACT FROM AUTHOR]