Search

A high-current electric arc inside an electrical switchgear can be a source of danger to electrical equipment and technical personnel. The article shows that the use of hybrid connectors as an arc eliminator significantly shortens the time of electric arc burning, and as a result reduces the electric arc energy. As a result, an effective device was obtained to protect low-voltage networks against the effects of short-circuit or arc fault, such as sudden increase in temperature, gas pressure, high-intensity sound wave, equipment destruction, material erosion of power rails, ejection hot debris and molten metal particles in all directions. Inside the closed switchgear, the proposed arc eliminator solution will significantly reduce the build-up of pressure and temperature.

This paper presents the results of testing the electrical and fire properties of mineral oil and low-viscosity natural ester mixtures. Properties such as breakdown voltage, relative permeability, dispersion coefficient, conductivity, flash and burn point, and lower heating values were investigated in different concentrations of mixtures of the two liquids, as well as for the base liquids. To ensure equal humidity levels, the prepared samples of mixtures and base liquids were conditioned under identical climatic conditions, resulting in samples with similar relative humidity (9 ± 3)%. The obtained measurement results for mixtures of the two fluids were related to the values obtained for the base liquids and analyzed in terms of changes in electrical properties and fire safety when used as insulating liquids in transformers. The presented results are useful for supplementing knowledge on the possibilities of using dielectric liquid mixtures in high-voltage power devices, with to the aim of using mixtures as alternatives to mineral oil.

The supply of energy with the correct parameters to electrical appliances is possible with the use of energy converters. When a direct current is required, rectifier bridges are needed. These can be made using rectifier diodes. The problem of excessive junction temperatures in power diodes, which are used to build rectifier bridges and power converters, was recognized. For this reason, research work was carried out to create a model of a rectifier diode placed on a heat sink and to analyze the heat dissipation from the junction of this diode under forced convection conditions. The results obtained from the simulation work were compared with the results of thermographic temperature measurements. The boundary conditions chosen for the simulation work are presented. A method is also presented that determined the convection coefficient under forced convection conditions. The difference between the simulation results and the results of the thermographic measurements was found to be 0.1 °C, depending on the power dissipated at the junction and the air velocity around the diode.

An increase in reactive power consumption results in an increase in electricity costs. This negative phenomenon can be prevented by using reactive power compensation methods. One of them is the installation of capacitors. These capacitors are exposed to external conditions, such as temperature and humidity. As a consequence, the aging process occurs. Another negative phenomenon is the corrosion that occurs inside the capacitor as a result of moisture absorption. As a result of this phenomenon, the capacitor can be damaged. One of the symptoms of the ongoing corrosion of the inside of the capacitor is an increase in temperature. Capacitors designed for reactive power compensation operate at mains voltage. They are often placed in a switchgear. For this reason, the use of contact methods of temperature measurement is difficult and dangerous. An alternative is thermographic measurement. Determining the internal temperature of the capacitor by thermographic measurement of the temperature of the case is possible with the use of numerical methods. One of them is FEM (Finite Element Method). The temperature results on the capacitor housing obtained from the simulation work were verified by comparing them with the result of thermographic temperature measurement. Both values differed by 0.2 °C. On the basis of the defined model, the differences between the temperature inside the capacitor housing and the temperature on the capacitor housing were determined by simulation. A simplification was proposed by replacing the cylinder made of layers with a homogeneous cylinder.

This article concerns the indirect thermographic measurement of the junction temperature of a D00-250-10 semiconductor diode. Herein, we show how the temperature of the semiconductor junction was estimated on the basis of the heat sink temperature. We discuss the methodology of selecting the points for thermographic measurement of the heat sink temperature and the diode case. The method of thermographic measurement of the heat sink temperature and the used measurement system are described. The simulation method used to obtain the temperature of the semiconductor diode junction on the basis of the thermographic measurement of the heat sink temperature, as well as the method of determining the emissivity and convection coefficients, is presented. In order to facilitate the understanding of the discussed issues, the construction of the diode and heat sink used, the heat flow equation and the finite element method are described. As a result of the work carried out, the point where the diode casing temperature is closest to the junction temperature was indicated, as well as which fragments of the heat sink should be observed in order to correctly estimate the temperature of the semiconductor junction. The indirect measurement of the semiconductor junction temperature was carried out for different values of the power dissipated in the junction.

An excessive increase in reactive power consumption is unfavorable from the point of view of a power system. For this reason, devices compensating reactive power consumption are used. The capacitor is one such device. Capacitors must be tested regularly during their exploitation. One of the activities that should be performed is testing the degree of heating of the cells of a capacitor bank. Thermography can be used to perform such tests. This non-contact method has its limitations. Due to the angular emissivity and the change in the distance between the lens and the object under observation, the temperature measured with a thermographic camera may differ from the actual temperature. This phenomenon is visible on cylindrical capacitor cases. Consequently, depending on the location of the observation point on the capacitor case, the result of the thermographic temperature measurement may be different. To investigate this phenomenon, experimental work has been undertaken.

This article describes the measuring system and the influence of selected factors on the accuracy of thermographic temperature measurement using a macrolens. This method enables thermographic measurement of the temperature of a small object with an area of square millimeters as, e.g., electronic elements. Damage to electronic components is often preceded by a rise in temperature, and an effective way to diagnose such components is the use of a thermographic camera. The ability to diagnose a device under full load makes thermography a very practical method that allows us to assess the condition of the device during operation. The accuracy of such a measurement depends on the conditions in which it is carried out. The incorrect selection of at least one parameter compensating the influence of the factor occurring during the measurement may cause the indicated value to differ from the correct value. This paper presents the basic issues linked to thermographic measurements and highlights the sources of errors. A measuring stand which enables the assessment of the influence of selected factors on the accuracy of thermographic measurement of electronic elements with the use of a macrolens is presented.

The number of components of a thermographic temperature measurement uncertainty budget and their ultimate contribution depend on the conditions in which the measurement is performed. The acquired data determine the accuracy with which the uncertainty component is estimated. Unfortunately, when some factors have to be taken into account, it is difficult to determine the value of the uncertainty component caused by the occurrence of this factor. In the case of a thermographic temperature measurement, such a factor is the lack of sharpness of the registered thermogram. This problem intensifies when an additional macro lens must be used. Therefore, it is decided to commence research to prepare an uncertainty budget of thermographic measurement with an additional macro lens based on the B method described in EA-4/02 (European Accreditation publications). As a result, the contribution of factors in the uncertainty budget of thermographic measurement with additional macro lens and the value of expanded uncertainty were obtained.

This paper presents a method to limit the arc energy and hence the hazard risk category value according to IEEE 1584 by using a system of two oppositely connected multi-sectional thyristor branches. A test circuit for testing the effectiveness of a thyristor arc eliminator was designed and constructed. Arc ignition inside electrical switchgear can be a source of danger for technical personnel. The arc energy calculated according to the algorithms in IEEE 1584 can be significantly reduced by using multi-sectional arc eliminator MSAE. For the actual measuring object, the calculation of the hazardous arc flash zone and the hazard category was carried out for the system not equipped with an arc eliminator, and then the same was performed in a system with an arc eliminator. In parallel, the pressure inside the closed polyvinyl chloride (PVC) electrical box enclosure was measured and then compared with the calculated pressures that could occur during an arc fault. It was found that a Multi-Sectional Arc Eliminator (MSAE) effectively protects devices supplied from low voltage networks against the effects of short circuit or arc fault, such as the sudden increase of gas pressure inside the switchboard, which may cause it to break, significantly reduce the loss of electrode material, limit the spread of hot electrode material outside the switchgear, and also significantly reduces the energy of the electric arc.

This paper presents the effect of the impact of moisture in paper insulation used as insulation of transformer windings on its thermal conductivity. Various types of paper (cellulose and aramid) and impregnated (mineral oil, synthetic ester, and natural ester) were tested. The impact of paper and impregnated types on the changes in thermal conductivity of paper insulation caused by an increase in moisture were analyzed. A linear equation, describing the changes in thermal conductivity due to moisture, for various types of paper and impregnated, was developed. The results of measuring the thermal conductivity of paper insulation depending on the temperature are presented. The aim of the study is to develop an experimental database to better understand the heat transport inside transformers to assess aging and optimize their performance.

The paper analyzes the utilization of cable screen currents for earth fault identification and location. Attention is paid on cable and mixed feeders—cable and overhead lines. The principle of operation is based on utilization of 3 criterion values: Ratio of cable screen earthing current and zero sequence cable core current—RF110/15, phase shift between cable screen earthing current and zero sequence cable core current—α and cable screen admittance defined as a ratio of cable screen earthing current and zero sequence voltage—Y0cs. Earth fault location is possible thanks to discovered relation between RF110/15 and α, whereas Y0cs allows for reliable detection of earth faults. Detection and identification are very important because it allows to increase the reliability of supply—reduce downtime and number of consumers affected by the fault. The article presents a phase to ground fault current flow for different power system configurations. At the end solution, which improves location capabilities is proposed. The solution is analyzed in PSCAD software and verified by network experiment.

The paper focuses on finding short circuit duration for computing the dynamic effects in Extra High Voltage (EHV) distribution substations with flexible conductors with the use of probabilistic method. To find fault duration for selected substation points, a risk criterion was involved, namely the expected annual frequency of exceeding the calculated values of dynamic forces. A dedicated simulation model based on the Monte Carlo method was used to analyze the dynamic effects of short circuit current flow in the substation during faults within it and in its vicinity. The short circuit duration model is the key part of the simulation model. Due to the discussion of how the selected factors affect the estimated short circuit duration, indications helpful to find the values of the latter were formulated and some examples for the 220 kV distribution substation were given.

The paper presents a system of two oppositely connected multi-sectional thyristor branches. The system works as a multi-sectional arc eliminator (MSAE), protecting low-voltage electrical apparatus against the effects of an arcing fault. MSAE is designed to serve as a device cooperating with protected and secured electrical equipment. The use of thyristors in the proposed solution allows to obtain a high speed of operation, while multi-sectional thyristor branches significantly increase the permissible current load of the arc eliminator. A test circuit was designed and made to test the performance effectiveness of the multi-sectional thyristor arc eliminator. A number of tests were carried out with variable current values in the arc branch, taking into account the influence of thyristor conduction voltage and different thyristor gate release times. It was found that the multi-section thyristor arc eliminator system effectively protects devices powered from low voltage power network against the effects of interference or arc fault.

Due to fault currents occurring in electrical installations, high electromagnetic force values may be induced in current paths of low-voltage electromagnetic relays. This force may lead to an electromagnetic bounce that will further result in an electric arc ignition between contacts, and under some circumstances, it will result in contact welding. For the proper exploitation of relays, the threshold value of the maximum current, and thus the electrodynamic force, should be known. This force depends on several factors, including: contact materials, dimensions of relay current paths, relay electromagnetic coil, etc. This paper presents the results of calculations and an experiment on electromagnetic forces, which cover these factors. A static closing force, acting on the contacts, and the fault current were measured. As a result, values of the force and current threshold were obtained, which inform when an electrodynamic bounce may occur. The obtained result may be used in designing contact rivets and relay current paths together with the selection of adequate fault protection devices.

Contact resistance is an important maintenance parameter for electromagnetic switches, including low-voltage relays. The flow of significant current through electric contacts may influence the contact surface and thus the value of the electric contact resistance (ECR). The change in ECR is influenced not only by the value of current but also by the current phase. Therefore, the impact of the switching short-circuit current’s phase on the ECR was analyzed in this paper. Significant changes in the resistance after each switching cycle were observed. The ECR decreased significantly after each make operation, and a correlation with current amplitude, total let-through energy, and short-circuit time was not observed.

The paper presents the layout of two opposing thyristors working as an Arc Eliminator (AE). The presented solution makes it possible to protect an electrical apparatus against the effects of an arcing fault. An Arc Eliminator is assumed to be a device cooperating with the protected apparatus. Thyristors were used because of their speed of operation and a relatively lower cost compared to other semiconductors with the same current-carrying capacity. The proposed solution, as one of the few currently available, makes it possible to eliminate the fault arc—both at short-circuit currents and current values to which overcurrent protections do not react. A test circuit was designed and made to study the effectiveness of the thyristor arc eliminator. A series of tests was carried out with variable impedance in the arc branch, including the influence of circuit inductance on arc time. It was found that the thyristor arc eliminator effectively protects devices powered from a low voltage power network against the effects of a fault or arc fault. The correctness of system operation for a wide range of impedance changes in the circuit feeding the arc location was demonstrated.

This paper discusses the effect of doping of electro-insulating liquids with nanoparticle materials on the thermal properties of the obtained nanoliquids and heat transport in the transformer. Mineral oil, synthetic ester, and natural ester were used as base liquids. The effectiveness of doping base liquids with nanoparticles was supported by ultraviolet-visible (UV/VIS) measurements. In turn, Attenuated Total Reflection Fourier Transform Infrared (ATR-FTIR) confirmed the absence of intermolecular interactions (i.e., hydrogen bonding). The influence of modification of electro-insulating liquids with fullerene C60 and titanium dioxide TiO2 nanoparticles on such thermal properties as thermal conductivity, specific heat, kinematic viscosity, density, and thermal expansion was investigated. Based on these properties and the theory of similarity, the cooling efficiency of the transformer filled with the analyzed nanofluids was determined. Nanofluids’ cooling effectiveness was compared with the cooling effectiveness of the base liquids. This comparison was supported by an analysis of Grashof, Prandtl, and Nusselt numbers. It has been shown that the modification of electro-insulating liquids with nanoparticles widely used in order to improve their dielectric properties, such as C60 and TiO2, does not have a significant influence on their thermal properties. The addition of fullerene C60 caused an increase in kinematic viscosity, which was compensated by the increase in specific heat. In the case of TiO2, the addition of this nanoparticle resulted in an increase in kinematic viscosity and a decrease in specific heat, which were balanced out by the increase in thermal conductivity. In summary, the heat exchange-capacity of liquids did not change due to doping with nanoparticles.

The article discusses thermal properties of synthetic ester admixed with nanoparticles. The analyzed thermal properties were: thermal conductivity λ, kinematic viscosity υ, density ρ, specific heat cp, and the thermal expansion factor β- all obtained by means of measurements. On the basis of these, the authors calculated the heat transfer factor α, which determines the ability of the liquid to heat transport. The authors used nanoparticles of fullerene C60 and titanium oxide TiO2. The analysis of the thermal properties was done for the temperatures of 25, 40, 60 and 80 °C. The authors analyzed the impact of nanoparticles C60 and TiO2 on thermal properties of synthetic ester. They proved that fullerene C60 in principle had no influence on heat transfer factor α of the ester, while titanium oxide TiO2 had some positive influence on the factor, the value of which increased about 1–3%.

W artykule przedstawione zostały wyniki pomiarów współczynnika przewodności cieplnej właściwej wybranych cieczy elektroizolacyjnych w zależności od temperatury. Określona została wartość współczynnika przewodności cieplnej badanych cieczy elektroizolacyjnych w przedziale temperatury od 20°C do 100°C. Pomiar przewodności cieplnej przeprowadzono przy wykorzystaniu przedstawionego autorskiego układu pomiarowego. Uzyskane wyniki są istotne z punktu widzenia projektowania konstrukcji urządzeń elektroenergetycznych.