Search

Aiming at the removal of native oxide film on 2024-T3 Al alloy before plasma electrolytic oxidation, the methods to reduce the fatigue damage caused by grit blasting are explored. Effects of the grit size and pressure on surface roughness, residual compressive stress (RCS), and fatigue life of the Al alloy are studied. Increasing grit size and pressure leads to the increase in the surface roughness and RCS. Based on the theorem of momentum and tool cutting principle, mechanism of the grits on the craters and RCS is revealed. It is found that the angularness of the small-sized grit results in the formation of long scratches. The grit with high kinetic energy induces the large craters and high RCS. The craters are the primary fatigue crack initiation source. Moreover, the craters with long scratch and large height lead to the premature fatigue failure of the grit blasted specimens. However, Fatigue behavior is insignificantly affected by the RCS. The results provide new insights into the fatigue deterioration mechanism and life optimization of the grit blasted samples. Consequently, a parameter optimization scheme for the fatigue life of the grit blasted Al alloy is proposed.

The stress analysis of micro-arc oxidation (MAO) coated aero Al alloys is the basis to reveal the mechanism of fatigue deterioration. To clarify effects of the coating defects on fatigue life, a stress calculation model with micropores and residual stress is established based on shear lag model in this study. The effects of porosity, substrate elastic modulus, coating thickness and residual stress on the stress are explored. The results indicate that the coating porosity and thickness are the critical factor affecting coating normal stress and interfacial shear stress, respectively. In addition, the residual stress significantly affects the interfacial normal stress. The increasing stress caused by low porosity and residual tensile stress and stress concentration at the large-sized defects are the key factors for fatigue degradation.

ABSTRACT Soil salinization usually occurs in arid and semi-arid climate areas from 37 to 50 degrees north latitude and 73 to 123 degrees east longitude. These regions are inhabited by a large number of Coleopteran insects, which play an important role in the ecological cycle. However, little is known about the endosymbiotic microbial taxa and their biological characteristics in these insects. A study of endosymbiotic microorganisms of Coleoptera from Xinjiang, a typical arid and inland saline area, revealed that endosymbiont bacteria with salinity tolerance are common among the endosymbionts of Coleoptera. Functional prediction of the microbiota analysis indicated a higher abundance of inorganic ion transporters and metabolism in these endosymbiont strains. Screening was conducted on the tolerable 11% NaCl levels of Brevibacterium casei G20 (PRJNA754761), and differential metabolite and proteins were performed. The differential metabolites of the strain during the exponential and plateau phases were found to include benzene compounds, organic acids, and their derivatives. These results suggest that the endosymbiotic microorganisms of Coleoptera in this environment have adaptive evolution to extreme environments, and this group of microorganisms is also one of the important resources for mining saline and alkaline-tolerant chassis microorganisms and high-robustness enzymes.IMPORTANCEColeoptera insects, as the first largest order of insect class, have the characteristics of a wide variety and wide distribution. The arid and semi-arid climate makes it more adaptable. By studying the endosymbiont bacteria of Coleoptera insects, we can systematically understand the adaptability of endosymbiont bacteria to host and special environment. Through the analysis of endosymbiont bacteria of Coleoptera insects in different saline-alkali areas in arid and semi-arid regions of Xinjiang, it was found that bacteria in different host samples were resistant to saline-alkali stress. These results suggest that bacteria and their hosts co-evolved in response to this climate. Therefore, this study is of great significance for understanding the endosymbiont bacteria of Coleoptera insects and obtaining extremophile resources (Saline-alkali-resistant chassis strains with modification potential for the production of bulk chemicals and highly robust industrial enzymes).

In this study, a rapid, inexpensive, and accurate colorimetric sensor for detecting psychrophilic bacteria was designed, comprising gold (Au) nanoparticles (NPs) modified by d-amino acid (D-AA) as color-metric probes. Based on the aggregation of Au NPs induced by psychrophilic bacteria, a noticeable color shift occurred within 6 h. Depending on the various metabolic behaviors of bacteria to different D-AA, four primary psychrophilic bacteria in raw milk were successfully distinguished by learning the response patterns. Furthermore, the quantification of single bacteria and the practical application in milk samples could be realized. Notably, a rapid colorimetric method was constructed by combining Au/D-AA with antibiotics for the minimum inhibitory concentration of psychrophilic bacteria, which relied on differences in bacteria metabolic activity in response to diverse antibiotic treatments. Therefore, the method enables the rapid detection and susceptibility evaluation of psychrophilic bacteria, promoting clinical practicability and antibiotic management.

Abstract Aims In-depth studies on plant ion uptake and plant growth-promoting rhizobacteria (PGPR) at the molecular level will help to further reveal the effects of PGPR on plants and their interaction mechanisms under salt stress. Methods Cotton was inoculated with a PGPR-Enterobacter cloacae Rs-35, and the ion uptake capacity, membrane transporter protein activity, and expression of key genes were determined under salt stress. Changes in the endogenous hormone content of cotton were also determined. Further, the genome-wide metabolic pathway annotation of E. cloacae Rs-35 and its differential enrichment pathway analysis of multi-omics under salinity environments were performed. Results In a pot experiment of saline-alkali soil, E. cloacae Rs-35-treated cotton significantly increased its uptake of K+ and Ca2+ and decreased uptake of Na+, elevated the activity of the H+-ATPase, and increased the sensitivity of the Na+/H+ reverse transporter protein on the vesicle membrane. Meanwhile, inoculation with E. cloacae Rs-35 could promote cotton to maintain the indole-3-acetic acid (IAA) content under salt stress. Genome-wide annotation showed that E. cloacae Rs-35 was respectively annotated to 31, 38, and 130 related genes in osmotic stress, phytohormone and organic acid metabolism, and ion uptake metabolic pathway. Multi-omics differences analysis showed that E. cloacae Rs-35 were enriched to tryptophan metabolism, multiple amino acid biosynthesis, carbon and glucose synthesis, and oxidative phosphorylation metabolic pathways at the transcriptome, proteome, and metabolome. Conclusion E. cloacae Rs-35 can promote cotton balance cell ion concentration, stabilize intracellular IAA changes, stimulate induction of systemic tolerance, and promote the growth of cotton plants under salt stress.

Abstract Background Milk production traits are complex traits with vital economic importance in the camel industry. However, the genetic mechanisms regulating milk production traits in camels remain poorly understood. Therefore, we aimed to identify candidate genes and metabolic pathways that affect milk production traits in Bactrian camels. Methods We classified camels (fourth parity) as low- or high-yield, examined pregnant camels using B-mode ultrasonography, observed the microscopic changes in the mammary gland using hematoxylin and eosin (HE) staining, and used RNA sequencing to identify differentially expressed genes (DEGs) and pathways. Results The average standard milk yield over the 300 days during parity was recorded as 470.18 ± 9.75 and 978.34 ± 3.80 kg in low- and high-performance camels, respectively. Nine female Junggar Bactrian camels were subjected to transcriptome sequencing, and 609 and 393 DEGs were identified in the low-yield vs. high-yield (WDL vs. WGH) and pregnancy versus colostrum period (RSQ vs. CRQ) comparison groups, respectively. The DEGs were compared with genes associated with milk production traits in the Animal Quantitative Trait Loci database and in Alashan Bactrian camels, and 65 and 46 overlapping candidate genes were obtained, respectively. Functional enrichment and protein–protein interaction network analyses of the DEGs and candidate genes were conducted. After comparing our results with those of other livestock studies, we identified 16 signaling pathways and 27 core candidate genes associated with maternal parturition, estrogen regulation, initiation of lactation, and milk production traits. The pathways suggest that emerged milk production involves the regulation of multiple complex metabolic and cellular developmental processes in camels. Finally, the RNA sequencing results were validated using quantitative real-time PCR; the 15 selected genes exhibited consistent expression changes. Conclusions This study identified DEGs and metabolic pathways affecting maternal parturition and milk production traits. The results provides a theoretical foundation for further research on the molecular mechanism of genes related to milk production traits in camels. Furthermore, these findings will help improve breeding strategies to achieve the desired milk yield in camels. Graphical Abstract

To predict the geometric characteristics and improve the forming quality and macro-micro defects of multi-track overlapping cladding layer effectively, the experimental research of laser melting deposition single-track Co-based alloy on 42CrMo substrate was carried out. The influence trends of laser process parameters on the single-track cladding height and cladding width were analyzed, and the regression prediction models were established. A variable-process alternated overlapping strategy was proposed using the geometric functions to fit the single-track profile. The surface forming quality and macro-micro defect of different overlapping cladding layers were compared and evaluated. The results showed that the cladding height and cladding width regression models established by an improved optimization algorithm had an excellent prediction effect. The variable-process alternated overlapping cladding layer prepared by the parabolic function had a flat surface, and the fluctuation distance was 81.56 μm, which was significantly improved compared with other overlapping strategies. The surface flatness of the continuous overlapping cladding layer was the worst and the spheroidization defect was the most unsatisfied. The internal defects of the constant-process alternated overlapping cladding layer were the most terrible, with more non-fusion and cracks caused by oxides. The variable-process alternated overlapping strategy proposed in this study can effectively prepare a multi-track cladding layer with a smooth surface and dense interior, which provides essential theoretical guidance for the near-net forming of component surface deposition and repair.

The impact of climates on the radial growth of muti-species remains insufficiently understood in the climate-sensitive southeastern Tibetan Plateau, and this hampers an effective assessment of forest growth under the background of global warming. Here, we studied the growth–climate relationships of three major species (Abies georgei, Larix potaninii, and Picea likiangensis) on the Baima Snow Mountain (BSM) by using dendrochronology methods. We constructed basal area increment (BAI) residual chronologies based on the dated ring-width measurements and correlated the chronologies with four climate factors. We also calculated the contributions of each climate factor to species growth. We found that photothermal conditions played a more important role than moisture in modulating radial growth, and P. likiangensi presented the strongest sensitivity to climate change among the three species. The growing season (June and July) temperature positively affected the radial growth of three species. Winter (previous December and current January) SD negatively impacted the tree growth of A. georgei and P. likiangensis. Significant correlations between growth and precipitation were detected only in A. georgei (January and May). Warming since the beginning of the 1950s promoted the growth of A. georgei and P. likiangensis, while the same effect on L. potaninii growth was found in the recent 50 years.

Unavoidable issues of micro-arc oxidation (MAO) coated Al alloys are the micro-defects and residual stress generation. Some scientists have reported the effects of micro-defects and residual stress on the fatigue performance of MAO coated samples. However, the influence of the residual stress sign in the MAO coating and substrate beneath the interface on the fatigue damage behavior of the substrate was controversial. Moreover, the coupling mechanism between micro-defects and residual stress on the fatigue performance of the MAO coated samples was nebulous. These present a challenge for the collaborative design of micro-defects and residual stress to optimize fatigue performance. Aiming at the issues, this paper summarized the influencing factors of MAO coatings on the fatigue performance of the substrate. From two aspects of microstructure characterization and stress analysis, the coupling mechanism between micro-defects and residual stress in fatigue failure was elucidated. And the mechanism of the micro-defects and residual stress on the fatigue damage behavior was developed. Finally, strategies to optimize the fatigue performance of MAO coated Al alloys were proposed. The results of this study have great guiding significance in regulating micropores, cracks, interface defects, and residual stress in MAO coatings in order to extend fatigue life.

Preparation of coatings with excellent properties is an effective way to address poor wear and corrosion resistance of aluminum (Al) alloys. Micro-arc oxidation (MAO) coatings exhibited high hardness, good adhesion, excellent corrosion and wear resistance. Unfortunately, defects such as micropores, cracks, overgrowth regions, and rough surface, as well as residual stress in MAO coatings are unavoidable. This entails that surface properties associated with corrosion resistance, wear resistance, and adhesion, as well as fatigue performance (SPAFP) of the MAO coated samples were more difficult to be controlled. In response to this issue, defects and residual stress control of MAO coating aiming at SPAFP optimization were studied. In this paper, the formation mechanism of MAO coating–effects of parameters on defects and residual stress–effects of defects and residual stress on the SPAFP of the MAO coated Al alloys were reviewed. Furthermore, an optimized control strategy for SPAFP was summarized. Coupling effect of micropores, cracks, rough surface, overgrowth regions, and residual stress on the SPAFP of MAO coated Al alloys was focused on. Aiming at the fatigue damage behavior, the anti-fatigue design method for the MAO coated Al alloys was proposed.

Abstract Background In camels, nasopharyngeal myiasis is caused by the larvae of Cephalopina titillator, which parasitize the tissues of nasal and paranasal sinuses, pharynx, and larynx. C. titillator infestation adversely affects the health of camels and decreases milk and meat production and even death. However, the C. titillator infestation in Bactrian camels has not been widely studied. Methods The present study was conducted to determine the prevalence and risk factors of C. titillator in Bactrian camels of northwestern Xinjiang. Suspected larvae recovered from infested camels were evaluated for C. titillator by microscopy and polymerase chain reaction. Nucleotide sequences of the partial mitochondrial cytochrome c oxidase subunit I (COX1) and cytochrome b (CYTB) genes from the C. titillator of camels were aligned from the NCBI database. Furthermore, the gross and histopathological alterations associated with C. titillator infestation were evaluated via pathological examination. Results Of 1263 camels examined 685 (54.2%) camels were infested with suspected C. titillator larvae. Different larval stages were topically detected in the nasal passages and pharynx of the camel heads. Microscopy analysis of the pharyngeal mucosa tissue revealed necrotic tissue debris and some inflammatory cells. Molecular detection of the larval COX1 and CYTB genes indicated that pathogen collected in Bactrian camels was C. titillator. The epidemiological study demonstrated that the prevalence rate of C.titillator infestation was significantly higher in camels of Bestierek Town Pasture (67.2%) and Karamagai Town Pasture (63.6%) compared to Kitagel Town Pasture (38.7%) and Qibal Town Pasture (35.8%) (P 0.05). The prevalence was higher in warm (64.2%) than that in cold (48.4%) seasons (P 10 (61.1%) years old compared to those of aged

OX40 (CD134), a member of the TNF receptor superfamily, is a widely studied costimulatory immune checkpoint. Several OX40 agonistic antibodies are in the clinical stage for cancer treatment, among which PF-04518600 is the leader and currently in phase II trial. It has been recognized that one potential mode of action for anti-OX40 antibodies is the deletion of intratumoral Tregs. Thus, a novel human anti-OX40 antibody, BAT6026, was generated with enhanced antibody dependent cellular cytotoxicity (ADCC) via fucose deletion to strengthen its Treg depletion activity. This characteristic of BAT6026 differentiates it from other previously reported anti-OX40 antibodies in the field of tumor therapy. The affinity of BT6026 to OX40 was 0.28nM, approximately 8 times stronger than that of PF-04518600. BAT6026 effectively competed for the binding of ligand OX40L to OX40, whereas PF-04518600 only partially competed. Moreover, compared to PF-04518600, BAT6026 activated T cells more effectively when clustered by FcγRs engagement and stimulated SEB-pretreated PBMCs to secrete IL-2 cytokines in vitro. In addition, BAT6026 demonstrated stronger anti-tumor activity than PF-04518600 in an OX40-humanized mouse MC38 tumor model. BAT6026 also showed a significantly synergistic effect on tumor inhibition when combined treatment with PD-1 antibody. Analysis of tumor-infiltrating T cells revealed that BAT6026 treatment significantly reduced Treg cells and increased CD8+ T cells in tumor. Preclinical safety assessment in non-human primates demonstrated a good safety profile for BAT6026. Together these data warrant further development of BAT6026 into clinical trials for patients with cancer.

Abstract Background Advances in DNA sequencing technologies have transformed our capacity to perform life science research, decipher the dynamics of complex soil microbial communities and exploit them for plant disease management. However, soil is a complex conglomerate, which makes functional metagenomics studies very challenging. Results Metagenomes were assembled by long-read (PacBio, PB), short-read (Illumina, IL), and mixture of PB and IL (PI) sequencing of soil DNA samples were compared. Ortholog analyses and functional annotation revealed that the PI approach significantly increased the contig length of the metagenomic sequences compared to IL and enlarged the gene pool compared to PB. The PI approach also offered comparable or higher species abundance than either PB or IL alone, and showed significant advantages for studying natural product biosynthetic genes in the soil microbiomes. Conclusion Our results provide an effective strategy for combining long and short-read DNA sequencing data to explore and distill the maximum information out of soil metagenomics.

ABSTRACT Populus euphratica Oliv. has a high tolerance for drought, salinity, and alkalinity. The main purpose of this study is to explore the effects of environments of different salinity intensities on endophytic community structure and the possible roles of endophytes in the tolerance of host plants. The characterization of endogenous bacteria in diversity has been investigated by using the Illumina high-throughput sequencing technique. The research showed that endophytic bacteria of P. euphratica in an extremely saline environment had low species diversity, especially in sap tissue. The dominant phyla in all groups were Proteobacteria, Actinobacteria, and Bacteroidetes. Notably, Firmicutes (relative abundance >5%) was a different dominant phylum in the samples from the high-saline environment compared with the relatively low-saline-environment group. The linear discriminant analysis effect size (LEfSe) analysis found that there were significant differences in different saline environments of Cytophagaceae (family), Rhodobacteraceae (family), and Rhodobacterales (order). These results indicated that the composition of the endogenous bacterial community was related to the growth environment of host plants. The predictive analysis of KEGG pathways and enzymes showed that the abundance of some enzymes and metabolic pathways of endophytes of P. euphratica increased with the increase of soil salinity, and most of the enzymes were related to energy metabolism and carbohydrate metabolism. These findings suggested that the endogenous bacteria of the host plant had different expression mechanisms under different degrees of stress, and this mechanism was very obvious in the distribution of endophytes, while the function of the endogenous bacteria needs to be further explored. IMPORTANCE Euphrates poplar (Populus euphratica Oliv.), as the only tree species that grows in the desert, has tenacious vitality with the characteristics of cold tolerance, drought tolerance, salt-alkali tolerance, and wind-sand resistance. P. euphratica has a long growth cycle and a high growth rate, which can break wind, fix sand, green the environment, and protect farmland, making it an important afforestation tree species in arid and semiarid areas. The area of P. euphratica in Xinjiang accounts for 91.1% of its area in China. Studying the endophytic bacteria of P. euphratica can give people a systematic understanding of it and the adaptability of the endogenous flora to the host and special environments. In this study, by analyzing the endophytic bacteria of P. euphratica in different saline-alkali regions of Xinjiang, it was found that the bacteria in different tissues of P. euphratica changed with the change of soil salinity. Especially in the sap tissue of P. euphratica under extremely high salinity, the diversity of endogenous bacteria was significantly lower than that in other tissues. These differential bacteria under different salinities were mostly related to the stress resistance of themselves and the host. Not only that, we also selected a strain of Bacillus with high stress resistance from the tissues of P. euphratica, which can survive under the extreme conditions of 10% NaCl and pH 11. We obtained a genome completion map of this strain, named it Bacillus haynesii P19 (GenBank accession no. PRJNA648288), and tried to use it for fermentation but in a different work, so as to develop it into a promising industrial fermentation chassis bacterium. Therefore, this study was of great significance for the understanding of endophytic bacteria in P. euphratica and the acquisition of extremophilic microbial resources.

The allocation pattern of plant biomass presents the strategy of the plant community to adopt environmental changes, while the driver of biomass allocation is still unclear in degraded alpine grassland ecosystems. To explore the issue, this study investigated the shoot-to-root (R/S) ratio, plant aboveground traits, and root competition of three functional groups (i.e., grasses, sedges, and forbs) at three degradation levels (i.e., no obvious degradation, ND; moderate degradation, MD; and severe degradation, SD) in an alpine meadow in the eastern Qinghai-Tibetan Plateau. The relationships among plant aboveground traits, root competition, and R/S ratio were tested using the structural equation model (SEM). The results showed that the shoot and root biomass tended to decrease, but the R/S ratio of the plant community did not change along the degradation gradient. Plant height, lateral spread, and leaf length of most plant functional groups reduced, while leaf width and leaf area of most plant functional groups did not change along the degradation gradients. The root competition ability (presented as the fraction of root biomass in total biomass) of sedges in MD was the lowest, while that of grasses was the highest. The effects of aboveground competition on the R/S ratio were non-linear because of the different roles of plant height, lateral spread, and leaf area in regulating the R/S ratio along the degradation gradient. In contrast, the effects of belowground competition on the R/S ratio were linear because belowground competition promoted the R/S ratio, and the strength of this effect reduced along the degradation gradient. These results indicate that plant competition might be a critical factor to maintain the high R/S ratio in degraded alpine meadows.

To explore the milling characteristics of Ni-based superalloy under minimal quantity lubrication (MQL), a single-factor experiment was adopted to investigate the milling machinability of GH4169 Ni-based superalloy. The influences of milling parameters and cooling methods on workpiece surface roughness, milling force, and surface hardness were analyzed. The results showed that the milling parameters and cooling methods have significant effects on the milling machinability of GH4169 Ni-based superalloy. The milling force was Fy > Fx > Fz, and the milling force decreased first and then increased with the increasing cutting speed. The surface roughness, surface hardness, and work hardening rate of the workpieces decreased with the increasing cutting speed and increased with the increasing feed per tooth and radial cutting depth. The milling parameters had a nonsignificant effect on the depth of the work hardening layer in GH4169 Ni-based superalloy. The order of cooling methods to obtain the minimum surface roughness and minimum milling force is nanofluid MQL > MQL > air cooling > no cooling.

ABSTRACT Total biosynthesis or whole-cell biocatalytic production of sulfated small molecules relies on the discovery and implementation of appropriate sulfotransferase enzymes. Although fungi are prominent biocatalysts and have been used to sulfate drug-like phenolics, no gene encoding a sulfotransferase enzyme has been functionally characterized from these organisms. Here, we identify a phenolic sulfotransferase, FgSULT1, by genome mining from the plant-pathogenic fungus Fusarium graminearum PH-1. We expressed FgSULT1 in a Saccharomyces cerevisiae chassis to modify a broad range of benzenediol lactones and their nonmacrocyclic congeners, together with an anthraquinone, with the resulting unnatural natural product (uNP) sulfates displaying increased solubility. FgSULT1 shares low similarity with known animal and plant sulfotransferases. Instead, it forms a sulfotransferase family with putative bacterial and fungal enzymes for phase II detoxification of xenobiotics and allelochemicals. Among fungi, putative FgSULT1 homologues are encoded in the genomes of Fusarium spp. and a few other genera in nonsyntenic regions, some of which may be related to catabolic sulfur recycling. Computational structure modeling combined with site-directed mutagenesis revealed that FgSULT1 retains the key catalytic residues and the typical fold of characterized animal and plant sulfotransferases. Our work opens the way for the discovery of hitherto unknown fungal sulfotransferases and provides a synthetic biological and enzymatic platform that can be adapted to produce bioactive sulfates, together with sulfate ester standards and probes for masked mycotoxins, precarcinogenic toxins, and xenobiotics. IMPORTANCE Sulfation is an expedient strategy to increase the solubility, bioavailability, and bioactivity of nutraceuticals and clinically important drugs. However, chemical or biological synthesis of sulfoconjugates is challenging. Genome mining, heterologous expression, homology structural modeling, and site-directed mutagenesis identified FgSULT1 of Fusarium graminearum PH-1 as a cytosolic sulfotransferase with the typical fold and active site architecture of characterized animal and plant sulfotransferases, despite low sequence similarity. FgSULT1 homologues are sparse in fungi but form a distinct clade with bacterial sulfotransferases. This study extends the functionally characterized sulfotransferase superfamily to the kingdom Fungi and demonstrates total biosynthetic and biocatalytic synthetic biological platforms to produce unnatural natural product (uNP) sulfoconjugates. Such uNP sulfates may be utilized for drug discovery in human and veterinary medicine and crop protection. Our synthetic biological methods may also be adapted to generate masked mycotoxin standards for food safety and environmental monitoring applications and to expose precarcinogenic xenobiotics.

A previous study found the key transcription factor of Litopenaeus vannamei PERK-eIF2α pathway cyclic AMP-dependent transcription factor 4 (LvATF4) was involved in the transcriptional regulation of white spot syndrome virus (WSSV) gene wsv023. Knocked-down expression of LvATF4 reduced the viral copy number and the cumulative mortality of WSSV-infected shrimp. These results suggested that wsv023 may be critical to WSSV infection but the precise function of wsv023 was still unknown. By using co-immunoprecipitation and pull-down assays, we show that wsv023 interacts with L. vannamei gamma complex-associated protein 2 (LvGCP2), which is the core protein of the γ-tubulin small complex. Knocked-down, the wsv023 gene significantly reduced the copy number of WSSV in L. vannamei muscle, as well as the cumulative mortality of infected shrimp. And PERK-eIF2α pathway inhibition also showed reduced virus copy number and abrogated shrimp mortality. Furthermore, overexpression of wsv023 inhibited the formation of microtubules in 293T cells. Flow cytometry revealed that WSSV infection similarly decreased the formation of microtubules in L. vannamei haemocytes. These findings suggested that wsv023 plays a role in microtubule organization in host cells, which in turn may be beneficial to WSSV.

To improve the milling surface quality of the Al-Li alloy thin-wall workpieces and reduce the cutting energy consumption. Experimental research on the milling processing of AA2195 Al-Li alloy thin-wall workpieces based on Response Surface Methodology was carried out. The single factor and interaction of milling parameters on surface roughness and specific cutting energy were analyzed, and the multi-objective optimization model was constructed. The Multiobjective Particle Swarm Optimization algorithm introducing the Chaos Local Search algorithm and the adaptive inertial weight was applied to determine the optimal combination of milling parameters. It was observed that surface roughness was mainly influenced by feed per tooth, and specific cutting energy was negatively correlated with feed per tooth, radial cutting depth and axial cutting depth, while cutting speed has a non-significant influence on specific cutting energy. The optimal combination of milling parameters with different priorities was obtained. The experimental results showed that the maximum relative error of measured and predicted values was 8.05%, and the model had high reliability, which ensured the low surface roughness and cutting energy consumption. It was of great guiding significance for the success of Al-Li alloy thin-wall milling with a high precision and energy efficiency. [ABSTRACT FROM AUTHOR]