Search

The SliT ASIC is a readout chip for the silicon strip detector to be used at the J-PARC muon $g-2$/EDM experiment. The production version of SliT128D was designed and mass production was finished. A quality assurance test method for bare SliT128D chips was developed to provide a sufficient number of chips for the experiment. The quality assurance test of the SliT128D chips was performed and 5735 chips were inspected. No defect was observed in chips of 84.3%. Accepting a few channels with poor time walk performance out of 128 channels per chip, more than 90% yield can be achieved, which is sufficient to construct the whole detector., Comment: 5 pages, 8 figures

The COMET experiment at J-PARC aims to search for the neutrinoless transition of a muon to an electron. We have developed the readout electronics board called ROESTI for the COMET straw tube tracker. We plan to install the ROESTI in the gas manifold of the detector. The number of vacuum feedthroughs needs to be reduced due to space constraints and cost limitations. In order to decrease the number of vacuum feedthroughs drastically, we developed a network processor with a daisy-chain function of Gigabit Ethernet for the FPGA on the ROESTI. We implemented two SiTCPs, which are hardware-based TCP processors for Gigabit Ethernet, in the network processor. We also added the data path controllers which handle the Ethernet frames and the event data. The network processor enables ROESTI to process the slow control over UDP/IP and to transfer event data over TCP/IP. By using the network processor, we measured the throughput, the stability, and the data loss rate for two to six ROESTIs. In any number of boards, the throughput of the event data transfer achieved the theoretical limit of TCP over the Gigabit Ethernet stably and ROESTI stably sent 100% of the data., Comment: IEEE Real Time 2020 Conference, 8 pages, 17 figures

J-PARC E16 is an experiment to examine the origin of hadron mass through a systematic measurement of spectral changes of vector mesons in nuclei. The measurement of $e^{+}e^{-}$ pairs from the decay of vector mesons will provide the information of the partial restoration of the chiral symmetry in a normal nuclear density. To resolve a pulse pile-up and achieve good discrimination of $e^{\pm}$ from the background of a reaction rate of an order of 10 MHz, the data acquisition (DAQ) system uses waveform sampling chips of APV25 and DRS4. The trigger rate and data rate are expected to be 1 kHz and 130--330 MiB/s, respectively. The DAQ system for readout of APV25 and DRS4 were developed, where events were synchronized by common trigger and tag data. The first commissioning in beam, called Run-0a, was performed in June 2020 with about 1/4 of the designed setup. The DAQ worked with a trigger rate of 300 Hz in the Run-0a and the main bottleneck was a large data size of APV25. Further optimization of the DAQ system will improve the performance., Comment: IEEE Real Time 2020 Conference, 4 pages, 6 figures

A new silicon-strip readout chip named "SliT" has been developed for the measurement of the muon anomalous magnetic moment and electric dipole moment at J-PARC. The SliT is designed in the Silterra 180 nm CMOS technology with mixed-signal integrated circuits. An analog circuit incorporates a conventional charge-sensitive amplifier, shaping amplifiers, and two distinct discriminators for each of 128 identical channels. A digital part includes storage memories, an event building block, a serializer, and LVDS drivers. A distinct feature of the SliT is utilization of the zero-cross architecture, which consists of a CR-RC filter followed by a CR circuit as a voltage differentiator. This architecture enables to generate hit signals with subnanosecond amplitude-independent time walk, which is the primary requirement for the experiment. The test results show the time walk of $0.38 \pm 0.16$ ns between 0.5 and 3 MIP signals. The equivalent noise charge is $1547 \pm 75 $ $e^{-}$ (rms) at $C_{\rm det} = 33$ pF as a strip-sensor capacitance. Other functionalities such as a strip-sensor readout chip have also been proven in the tests. The SliT128C satisfies all requirements of the J-PARC muon $g-2$/EDM experiment., Comment: 7 pages, 12 figures

Radiation damage on front-end readout and trigger electronics is an important issue in the COMET Phase-I experiment at J-PARC, which plans to search for the neutrinoless transition of a muon to an electron. To produce an intense muon beam, a high-power proton beam impinges on a graphite target, resulting in a high-radiation environment. We require radiation tolerance to a total dose of $1.0\,\mathrm{kGy}$ and $1\,\mathrm{MeV}$ equivalent neutron fluence of $1.0\times10^{12}\,\mathrm{n_{eq}\,cm^{-2}}$ including a safety factor of 5 over the duration of the physics measurement. The use of commercially-available electronics components which have high radiation tolerance, if such components can be secured, is desirable in such an environment. The radiation hardness of commercial electronic components has been evaluated in gamma-ray and neutron irradiation tests. As results of these tests, voltage regulators, ADCs, DACs, and several other components were found to have enough tolerance to both gamma-ray and neutron irradiation at the level we require.