Search

We present a study of battery ageing, comparing pristine, calendar-aged, and cycle-aged lithium-ion cells. Insight into degradation was obtained via differential voltage analysis and by estimating and tracking changes in a subset of electrochemical model parameters of the single particle model through inverse modelling. We show that both diffusion time and kinetic overpotential increase in cycle-aged cells, while calendar-aged cells experienced no diffusion time changes but some kinetic overpotential increase. The latter is also evident in 50% higher irreversible heat generation in cycle-aged cells. This study highlights the importance of updating battery model parameters during ageing.

Hard carbons show considerable potential as anode materials in emerging sodium-ion battery technologies. Recent work suggests sodiation of hard carbon proceeds by insertion of sodium at defects, within the interlayers and inside the nanopores. The energetics of these processes dictate the characteristic sloping region and plateau when hard carbon is charged/discharged with sodium. However, the driving forces affecting these processes, and particularly sodium filling into nanopores, are under debate and are holding back controlled material optimisation. We apply entropy profiling (EP), where the cell temperature is changed under open circuit conditions, to yield additional insights into sodium insertion in hard carbons of systematically controlled pore size. Features from EP vary with the pore size, allowing us to precisely determine the onset of nanopore filling. Comparing the system entropy and enthalpy data to models, we can quantify the energetics of sodium inside the nanopores. The average binding energy of sodium in the pores is found to be inversely proportional to the pore radius of curvature, which is attributed to the scaling of the surface area to volume inside the pores. This simple structure-property relationship provides a rational framework to tune the cell cut-off voltage of sodium-ion cells based on hard carbon, potentially enabling future materials of improved safety and longevity.

Graphite-silicon (Gr-Si) blends have become common in commercial Li-ion battery negative electrodes, offering increased capacity over pure graphite. Lithiation/delithiation of the silicon particles results in volume changes, which may be associated with increased hysteresis of the open circuit potential (OCP). The OCP is a function of both concentration and temperature. Entropy change measurement—which probes the response of the OCP to temperature—offers a unique battery diagnostics tool. While entropy change measurements have previously been applied to study degradation, the implications of Si additives on the entropy profiles of commercial cells have not been explored. Here, we use entropy profiling to track ageing markers in the same way as differential voltage analysis. In addition to lithiation/delithiation hysteresis in the OCP of Gr-Si blends, cells with Gr-Si anodes also exhibit differences in entropy profile depending on cycling direction, reflecting degradation-related morphological changes. For cycled cells, entropy change decreased during discharge, likely corresponding to graphite particles breaking and cracking. However, entropy change during charge increased with cycling, likely due to the volume change of silicon. Over a broad voltage range, these combined effects led to the observed rise in entropy hysteresis with age. Conversely, for calendar aged cells entropy hysteresis remained stable.

Computational modelling is a vital tool in the research of batteries and their component materials. Atomistic models are key to building truly physics-based models of batteries and form the foundation of the multiscale modelling chain, leading to more robust and predictive models. These models can be applied to fundamental research questions with high predictive accuracy. For example, they can be used to predict new behaviour not currently accessible by experiment, for reasons of cost, safety, or throughput. Atomistic models are useful for quantifying and evaluating trends in experimental data, explaining structure-property relationships, and informing materials design strategies and libraries. In this review, we showcase the most prominent atomistic modelling methods and their application to electrode materials, liquid and solid electrolyte materials, and their interfaces, highlighting the diverse range of battery properties that can be investigated. Furthermore, we link atomistic modelling to experimental data and higher scale models such as continuum and control models. We also provide a critical discussion on the outlook of these materials and the main challenges for future battery research.

Understanding and optimizing single particle rate behaviour is normally challenging in composite commercial lithium-ion electrode materials. In this regard, recent experimental research has addressed the electrochemical Li-ion intercalation in individual nanosized particles. Here, we present a thorough theoretical analysis of the Li+ intercalation voltammetric behaviour in single nano/micro-scale LiMn2 O4 (LMO) particles, incorporating realistic interactions between inserted ions. A transparent 2-dimensional zone diagram representation of kinetic-diffusional behaviour is provided that allows rapid diagnosis of the reversibility and diffusion length of the system depending on the particle geometry. We provide an Excel file where the boundary lines of the zone diagram can be rapidly recalculated by setting input values of the rate constant, k0 and diffusion coefficient, D . The model framework elucidates the heterogeneous behaviour of nanosized particles with similar sizes but different shapes. Hence, we present here an outlook for realistic multiscale modelling of real materials.

Sodium-ion batteries (NIBs) utilise cheaper materials than lithium-ion batteries (LIBs), and can thus be used in larger scale applications. The preferred anode material is hard carbon, because sodium cannot be inserted into graphite. We apply experimental entropy profiling (EP), where the cell temperature is changed under open circuit conditions. EP has been used to characterise LIBs; here, we demonstrate the first application of EP to any NIB material. The voltage versus sodiation fraction curves (voltage profiles) of hard carbon lack clear features, consisting only of a slope and a plateau, making it difficult to clarify the structural features of hard carbon that could optimise cell performance. We find additional features through EP that are masked in the voltage profiles. We fit lattice gas models of hard carbon sodiation to experimental EP and system enthalpy, obtaining: 1. a theoretical maximum capacity, 2. interlayer versus pore filled sodium with state of charge.

The longevity of lithium-ion batteries is determined by the rate of chemical and electrochemical side reactions that limit their charge storage capacity. In particular, dissolution of transition metals from the cathode accelerates the blockage of LixC6 anodes, but few direct dissolution studies have been made to date. Although LiMn2O4 (LMO) has been frequently used as a model electrode for dissolution studies, the cause and nature of dissolution and dissolution-free states are still unclear. By online inductively coupled plasma analysis, we detect dissolution from LMO electrodes in real time to reveal the role of surface versus bulk structure effects, electrode potential and degree of lithiation on Mn dissolution. We find that fully lithiated LMO, with an average Mn redox state of 3.5, readily dissolves when brought in contact with 0.2 M Li2SO4, but that on initial charging a dissolution–passivation event preceding delithiation abruptly stops further detectable dissolution, until well past fully delithiated λ-MnO2. Dissolution reactivates on returning to the initial potential of pristine LMO, and increases exponentially in the overlithiation region. Our results provide access to much more detailed dissolution information than post-mortem battery analysis allows, enabling targeted materials screening and informing best practices in charging/discharging profiles. In particular, our data suggests that suitable potential conditioning of electrodes may mitigate dissolution, as an alternative or additional measure to the use of protective surface films or incorporation of dopants.

Rational optimization of the OER activity of catalystsbased on LaNiO3 oxide is achieved by maximizing the presence of trivalent Ni in the surface structure. DFT investigations of the LaNiO3catalyst and surface structures related to it predict an improvement inthe OER activity for these materials to levels comparable with the topof the OER volcano if the La content is minimized while the oxidationstate of Ni is maintained. These theoretically predicted structures ofhigh intrinsic OER activity can be prepared by a templated spray-freeze freeze-drying synthesis followed by a simple postsynthesisexfoliation-like treatment in acidic media. These nanocrystallineLaNiO3-related materials confirm the theoretical predictions, showinga dramatic improvement in OER activity. The exfoliated surfacesremain stable in OER catalysis, as shown by an in-operando ICP-OESstudy. The unprecedented OER activation of the synthesized LaNiO3-based materials is related to a close juxtaposition of the theoretical conception of ideal structural motifs and the ability to engendersuch motifs using a unique synthetic procedure, both principally related to stabilization and pinning of the Ni oxidation state within the local coordination environment of the perovskite structure.

Cell voltage is a fundamental quantity used to monitor and control Li-ion batteries. The open circuit voltage (OCV) is of particular interest as it is believed to be a thermodynamic quantity, free of kinetic effects and history and, therefore, "simple" to interpret. Here we show that the OCV characteristics of graphite show hysteresis between charge and discharge that does not solely originate from Li dynamics and that the OCV is in fact history dependent. Combining First Principles calculations with temperature-controlled electrochemical measurements, we identify a residual hysteresis that persists even at elevated temperatures of greater than 50°C due to differences in the phase succession between charge and discharge. Experimental entropy profiling, as well as energies and volume changes determined from First Principles calculations, suggest that the residual hysteresis is associated with different host lattice stackings of carbon and is related to Li disorder across planes in stage II configurations.

To make a Lithium Ion Battery (LIB) reliably rechargeable over many cycles, its graphite-based negative electrode requires the solid electrolyte interphase (SEI) as a protection layer. The SEI is formed through chemical and particularly electrochemical side reactions of electrolyte components in the first charging cycle(s) after manufacturing of a LIB. The SEI ideally serves two purposes: (i) act as a sieve permeable to Li ions but not to other electrolyte components and (ii) passivate the electrode against further electrolyte decomposition. Core element of conventional SEI formation is a lengthy, low-current galvanostatic charging step, which due to its time consumption contributes heavily to cell manufacturing costs. Here, we report on some non-conventional SEI formation protocols for composite carbon electrodes, inspired by recent experimental findings at smooth model electrodes. Acknowledging that the SEI forms in two main steps, taking place in a high-potential and a low-potential region, respectively, we demonstrate that less time spent in the high-potential region not only makes the process faster but even yields SEIs with superior kinetic properties. We tentatively explain this via basic rules of thin film growth and the role of grain boundaries for ion transport. We also report on the positive influence of multi-frequency potential modulations applied between high-potential and low-potential formation. Given that any new cell chemistry in principle requires its own tailor-made formation process, technologic success of future LIB cells will benefit from a systematic, well-understood toolbox of formation protocols. This paper is meant as a first step, highlighting potentially low-hanging fruits, but also flagging the demand for further systematic studies on model systems and on commercially manufactured cells. © 2018 Elsevier Ltd

We demonstrate the predictive power of a parametrised Doyle-Fuller-Newman (DFN) model of a commercial cylindrical (21700) lithium-ion cell with NCA/Gr-SiOx chemistry. Model parameters result from the deconstruction of a fresh commercial cell to determine/confirm chemistry and micro-structure, and also from electrochemical experiments with half-cells built from electrode samples. The simulations predict voltage profiles for (i) galvanostatic discharge and (ii) drive-cycles. Predicted voltage responses deviate from measured ones by

In-situ diagnostic tools have become established to as a means to understanding the aging processes that occur during charge/discharge cycles in Li-ion batteries (LIBs). One electrochemical thermodynamic technique that can be applied to this problem is known as entropy profiling. Entropy profiles are obtained by monitoring the variation in the open circuit potential as a function of temperature. The peaks in these profiles are related to phase transitions, such as order/disorder transitions, in the lattice. In battery aging studies of cathode materials, the peaks become suppressed but the mechanism by which this occurs is currently poorly understood. One suggested mechanism is the formation of point defects. Intentional modifications of LIB electrodes may also lead to the introduction of point defects. To gain quantitative understanding of the entropy profile changes that could be caused by point defects, we have performed Monte Carlo simulations on lattices of variable defect content. As a model cathode, we have chosen manganese spinel, which has a well-described order-disorder transition when it is half filled with Li. We assume, in the case of trivalent defect substitution (M = Cr,Co) that each defect M permanently pins one Li atom. This assumption is supported by Density Functional Theory (DFT) calculations. Assuming that the distribution of the pinned Li sites is completely random, we observe the same trend in the change in partial molar entropy with defect content as observed in experiment: the peak amplitudes become increasing suppressed as the defect fraction is increased. We also examine changes in the configurational entropy itself, rather than the entropy change, as a function of the defect fraction and analyse these results with respect to the ones expected for an ideal solid solution. We discuss the implications of the quantitative differences between some of the results obtained from the model and the experimentally observed ones.

We demonstrate how insufficient heat transport in environmental chambers compromises the meaningfulness of high-precision charge counting and leads to an underestimation of lithium plating in fast-charged lithium-ion batteries. Direct-contact liquid cooling of cylindrical cells excludes temperature fluctuations observed in thermal chambers and restricts self-heating to 2 K in comparison to the 14 K in thermal chambers, under 1.5 C-rate cycling. Our thermal-electrochemical model replicated well the experimental results. For high-precision coulometric studies to be meaningful and more comparable across different laboratories, especially for large-format and high-power cells, direct-contact cooling in thermal baths must become the new standard.

We report on a cycle ageing study of commercial NCA/Gr+Si cells, in which reversible capacity fluctuations turn a central experimental finding upside down: an upper voltage limit of 4.1 V seems to cause faster degradation than going all the way to 4.2 V. The underlying effect is the reversible loss of lithium inventory into passive anode overhang areas. We demonstrate how the resulting artefact arises from a combination of slow transport processes and the related time periods spent in specific state-of-charge regions. We propose an alternative visualisation tool to identify and manage such artefacts, often neglected in typical ageing studies. © 2020 The Electrochemical Society (“ECS”).

We present preparenovonix, a Python package that handles common issues encountered in data files generated with a range of software versions from the Novonix battery-testers.1 This package can also add extra information that makes easier coulombic counting and relating a measurement to the experimental protocol. The package provides a master function that can run at once the cleaning and adding derived information, with flexibility to choose only some features. There is a separate function to simply read a column by its given name. The usage of all the functions is documented in the code including examples. The code presented here can be installed either as a python package2 or from a GitHub repository.3 Funding statement: This work has been conducted within the Multi Scale Modelling collaboration from the Faraday Institution: ALC7052 and ALC 7082.

The voltammetric behavior of Li+ intercalation/deintercalation in/from LiMn2O4 thin films and single particles is simulated, supporting very recent experimental results. Experiments and calculations both show that particle size and geometry are crucial for the electrochemical response. A remarkable outcome of this research is that higher potential sweep rates, of the order of several millivolts per second, may be used to characterize nanoparticles by voltammetry sweeps, as compared with macroscopic systems. This is in line with previous conclusions drawn for related single particle systems using kinetic Monte Carlo simulations. The impact of electrode kinetics and finite space diffusion on the reversibility of the process and the finiteness of the diffusion in ion Li / LiMn2O4 (de)intercalation is also discussed in terms of preexisting modeling. Fil: Gavilán Arriazu, Edgardo Maximiliano. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Córdoba. Instituto de Física Enrique Gaviola. Universidad Nacional de Córdoba. Instituto de Física Enrique Gaviola; Argentina Fil: Mercer, M.P.. Lancaster University; Reino Unido Fil: Pinto, Oscar Alejandro. Universidad Nacional de Santiago del Estero. Instituto de Bionanotecnología del Noa. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Tucumán. Instituto de Bionanotecnología del Noa; Argentina Fil: Oviedo, Oscar Alejandro. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Córdoba. Instituto de Investigaciones en Físico-química de Córdoba. Universidad Nacional de Córdoba. Facultad de Ciencias Químicas. Instituto de Investigaciones en Físico-química de Córdoba; Argentina Fil: Barraco Diaz, Daniel Eugenio. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Córdoba. Instituto de Física Enrique Gaviola. Universidad Nacional de Córdoba. Instituto de Física Enrique Gaviola; Argentina Fil: Hoster, H. E.. Lancaster University; Reino Unido Fil: Leiva, Ezequiel Pedro M.. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Córdoba. Instituto de Investigaciones en Físico-química de Córdoba. Universidad Nacional de Córdoba. Facultad de Ciencias Químicas. Instituto de Investigaciones en Físico-química de Córdoba; Argentina

We report on the first year of calendar ageing of commercial high-energy 21700 lithium-ion cells, varying over eight state of charge (SoC) and three temperature values. Lithium-nickel-cobalt-aluminium oxide (NCA) and graphite with silicon suboxide (Gr-SiOₓ) form cathodes and anodes of those cells, respectively. Degradation is fastest for cells at 70–80 % SoC according to monthly electrochemical check-up tests. Cells kept at 100 % SoC do not show the fastest capacity fade but develop internal short circuits for temperatures T≥40 °C. Degradation is slowest for cells stored close to 0 % SoC at all temperatures. Rates of capacity fade and their temperature dependencies are distinctly different for SoC values below and above 60 %, respectively. Differential voltage analyses, apparent activation energy analysis, and endpoint slippage tracking provide useful insights into the degradation mechanisms and the respective roles of anode and cathode potential. We discuss how reversible losses of lithium might play a role in alleviating the rate of irreversible losses on commercial cells.

Defects in the carbon microstructure have been reported to enhance the discharge performance of Li–O2 battery. However, systematic studies correlating the presence of defects with the discharge kinetics have not addressed the variation of carbon electrode surface areas. In this work, carbon blacks and carbon nanofibers with different defect densities were investigated for their discharge properties. The electrolyte-accessible areas of the carbon electrodes were obtained from Cyclic voltammetry measurements. The microstructure and surface areas of the carbons were characterized by Raman spectroscopy, electron microscopy, and N2 isotherm. Linear sweep voltammetry and galvanostatic discharge experiments consistently demonstrated that graphitic carbons have more negative onset potentials and more negative discharge potentials at the same current density than defective carbons. The linear sweep voltammetry data were normalized to the carbon masses, Brunauer–Emmet–Teller surface areas, and double layer capacitance-derived areas for comparison. Plot of inverse charge transfer resistance and double layer capacitance from electrochemical impedance spectroscopy measurements were used to extract current density values without knowledge of electrode areas. The current densities from impedance measurements exhibited good agreement with the data from linear sweep experiments. The electrochemical experiments conclusively showed that defects on the graphitic microstructure increase the discharge kinetics of the Li–O2 battery.

We highlight the impact of Ultrahigh Vacuum (UHV)-born surface science on modern electrocatalysis. The microscopic, atomic level picture of surface adsorption and reaction, which was developed in the surface science community in decades of systematic research on single crystals in UHV, has meanwhile become state-of-the-art also in electrochemistry. For the example of CO on Pt(111) single crystals, which has been extensively studied at the solid/gas and the solid/liquid interface using atomic resolution scanning tunnelling microscopy (STM), we highlight how both interfaces may have even more in common than often assumed. We then illustrate how planar model surfaces such as mono- and bimetallic single crystals and surface alloys, prepared and thoroughly analysed in UHV, enabled a systematic search for improved electrocatalysts. Surface alloys, thermodynamically more stable than foreign metal islands, are a particularly important sub-group of model surfaces, which so far have only been fabricated in UHV. We also flag that model surfaces may not always assume the structure anticipated for the respective experiment, regardless of their preparation in UHV or by electrochemical methods. “Accidental” surface alloying may be more common than often assumed, leading to misinterpretations of the structure-property relationships targeted in many model studies. We highlight that controlled surface alloy formation should be a key step in any model study looking at bimetallic systems in order to get an idea what the effect of unintended alloying could possibly be, and to cross-check whether alloyed surfaces may potentially be the better electrocatalysts in the first place.

Sodium-oxygen Lithium-oxygen (Li-O2) cells are popular due to their potentially high energy density. A characteristic fingerprint of a given cell is the voltage profile during constant-current discharge. We suggest that the typical initial dip and the following increase of the voltage result from a temporary increase and slow decrease in the concentration of dissolved superoxide, respectively, feeding into the Nernst equation. The steady-state superoxide concentration decreases as the surface area of the solid precipitation product (Li2O2) increases. Importantly, these products bury the electrochemically active carbon surface. Assuming that the electrochemical step only occurs on bare carbon, the Tafel equation provides an expression for the increasing overpotential as a result of the shrinking effective electrode area. This boils the discharge voltage profile down to the sum of two logarithms, grasping all relevant features in recorded discharge voltage profiles.

With the perennial demand for longer runtime of battery-powered Wireless Sensor Nodes (WSNs), several techniques have been proposed to increase the battery runtime. One such class of techniques exploiting the battery recovery effect phenomenon claims that performing an intermittent discharge instead of a continuous discharge will increase the usable battery capacity. Several works in the areas of embedded systems and wireless sensor networks have assumed the existence of this recovery effect and proposed different power management techniques in the form of power supply architectures (multiple battery setup) and communication protocols (burst mode transmission) in order to exploit it. However, until now, a systematic experimental evaluation of the recovery effect has not been performed with real battery cells, using high-accuracy battery testers to confirm the existence of this recovery phenomenon. In this article, a systematic evaluation procedure is developed to verify the existence of this battery recovery effect. Using our evaluation procedure, we investigated Alkaline, Nickel-Metal Hydride (NiMH), and Lithium-Ion (Li-Ion) battery chemistries, which are commonly used as power supplies for Wireless Sensor Node (WSN) applications. Our experimental results do not show any evidence of the aforementioned recovery effect in these battery chemistries. In particular, our results show a significant deviation from the stochastic battery models, which were used by many power management techniques. Therefore, the existing power management approaches that rely on this recovery effect do not hold in practice. Instead of a battery recovery effect, our experimental results show the existence of the rate capacity effect , which is the reduction of usable battery capacity with higher discharge power, to be the dominant electrochemical phenomenon that should be considered for maximizing the runtime of WSN applications. We outline power management techniques that minimize the rate capacity effect in order to obtain a higher energy output from the battery.

There is a great need for non-invasive tools that enable improved insight into the underlying causes of battery ageing. In this project we investigate cycling and calendar ageing effects on high energy commercial cylindrical cells (NCA|Si-Gr), by tracking thermodynamic and kinetic aspects by the employment of entropy profiling, differential voltage and incremental capacity analysis (DVA/ICA), and differential thermal voltammetry (DTV). Two groups of three cells from the same batch are being subjected to different ageing scenarios, both at 45°C: group A is under calendar aging at 75 % state of charge - SoC at which we observed the most accelerated calendric aging for these cells - and group B, which is being cycled continuously at the maximum current allowed by the manufacturer. To ensure minimal temperature fluctuations during tests and allow proper comparative DTV, cells were submerged in a high conductivity dielectric fluid bath. We revised Osswald’s approach for entropy profiling [1], and also increased the number of titration steps in entropy profiling to 63, for both charge and discharge. Fig. 1 shows the results for the initial 40-day aging period, comparing ICA and entropy profiles, before and after ageing. In addition to the capacity fade of 2.2 % and 6.2 % for groups A and B respectively (Figure 1a), the loss of sharpness present in the ICA peaks is also present in the entropy curves (features A1-A4 in Fig. 1b). This can be attributed to a more heterogeneous lithium distribution and a change in lithium inventory. To track the reversibility of ageing and the time scales of passive electrode effects [2], both groups of cells will be submitted to rest periods after which entropy, DTV and ICA experiments will be periodically repeated. References [1] P.J. Osswald, M. Del Rosario, J. Garche, A. Jossen, H.E. Hoster, Electrochim. Acta 177 (2015) 270–276. [2]M. Lewerenz, G. Fuchs, L. Becker, D.U. Sauer, J. Energy Storage 18 (2018) 149–159. Figure 1

Accurate health estimation and lifetime prediction of lithium-ion batteries are crucial for durable electric vehicles. Early detection of inadequate performance facilitates timely maintenance of battery systems. This reduces operational costs and prevents accidents and malfunctions. Recent advancements in “Big Data” analytics and related statistical/computational tools raised interest in data-driven battery health estimation. Here, we will review these in view of their feasibility and cost-effectiveness in dealing with battery health in real-world applications. We categorise these methods according to their underlying models/algorithms and discuss their advantages and limitations. In the final section we focus on challenges of real-time battery health management and discuss potential next-generation techniques. We are confident that this review will inform commercial technology choices and academic research agendas alike, thus boosting progress in data-driven battery health estimation and prediction on all technology readiness levels.

We report on an effective approach to speed up the measurement of thermodynamic characterization curves (entropy of reaction ΔrS(x)) of rechargeable batteries, in particular commercial 18,650 lithium ion cells. We propose and demonstrate a measurement and data processing protocol that reduces the time required to record entropy profiles from time scales of weeks to time scales of hours - without loss in accuracy. For time consuming studies such as investigations on ageing of battery cells, entropy profile measurements thus become as feasible as conventional electrochemical characterisation techniques like dV/dQ or cyclic voltammetry. We demonstrate this at the examples of two ageing protocols applied to a commercial high power and a commercial high energy cell, respectively: (i) accelerated calendric aging by storing cells at 100% state of charge at 60 °C and (ii) continuous cycling with a 1 C current at 25 °C.

Silicon is a potential high-capacity anode material for lithium-ion batteries. However, the large volume expansion of the material remains a bottleneck to its commercialization. Many studies were devoted to nanostructured silicon composites with voids to accommodate the volume expansion. Yet, full capability of silicon cannot be utilized because of the low volumetric capacity of these nanostructured electrodes. Here, we re-design dense silicon electrodes with three times the volumetric capacity of graphite by monitoring and limiting thickness changes of the electrodes. In-situ electrochemical dilatometry reveals that volume change is typically non-linear with state of charge, and highly affected by electrode composition. One key problem is the vertical displacement of the silicon particles by many times their own diameter during lithiation, which leads to irreversible detachment of active particles and increased porosity of the overall electrode for a weak binder. Better reversibility in electrode thickness change is achieved by using polyimide with higher modulus and larger ultimate elongation as the binder, resulting in better cycle stability.

Measurements of the open circuit voltage of Li-ion cells have been extensively used as a non-destructive characterisation tool. Another technique based on entropy change measurements has also been applied for this purpose. More recently, both techniques have been used to make qualitative statements about aging in Li-ion cells. One proposed cause of cell failure is point defect formation in the electrode materials. The steps in voltage profiles, and the peaks in entropy profiles are sensitive to order/disorder transitions arising from Li/vacancy configurations, which are affected by the host lattice structures. We compare the entropy change results, voltage profiles and incremental capacity (dQ/dV) obtained from coin cells with spinel lithium manganese oxide (LMO) cathodes, Li1+yMn2-yO4, where excess Li y was added in the range 0 ≤ y ≤ 0.2. A clear trend of entropy and dQ/dV peak amplitude decrease with excess Li amount was determined. The effect arises, in part, from the presence of pinned Li sites, which disturb the formation of the ordered phase. We modelled the voltage, dQ/dV and entropy results as a function of the interaction parameters and the excess Li amount, using a mean field approach. For a given pinning population, we demonstrated that the asymmetries observed in the dQ/dV peaks can be modelled by a single linear correction term. To replicate the observed peak separations, widths and magnitudes, we had to account for variation in the energy interaction parameters as a function of the excess Li amount, y. All Li-Li repulsion parameters in the model increased in value as the defect fraction, y, increased. Our paper shows how far a computational mean field approximation can replicate experimentally observed voltage, incremental capacity and entropy profiles in the presence of phase transitions.

The solid electrolyte interphase (SEI) on graphite anodes is a key enabler for rechargeable lithium-ion batteries (LIBs). It ensures that only Li+ ions and no damaging electrolyte components enter the anode and hinders electrolyte decomposition. Its growth should be confined to the initial SEI formation process and stop once the battery is in operation to avoid capacity/power loss. In technical LIB cells, the SEI is formed at constant current, with the potential of the graphite anode slowly drifting from higher to lower voltages. SEI formation rate, composition, and structure depend on the potential and on the chemical properties of the anode surface. Here, we characterize SEIs formed at constant potentials on the chemically inactive basal plane of highly oriented pyrolytic graphite (HOPG). X-ray photoemission spectroscopy (XPS) detects carbonate species only at lower formation potentials. Cyclic voltammetry (CV) and Electrochemical Impedance Spectroscopy (EIS) with Fc/Fc+ as an electrochemical probe demonstrate how the formation potential influences ion transport and electrochemical kinetics to and at the anode surface, respectively. Breaking the EIS data down to a Distribution of Relaxation Times (DRT) reveals distinct kinetics and transport related peaks with varying Arrhenius-type temperature dependencies. We discuss our findings in the context of previous electrochemical studies and existing SEI models and of SEI formation protocols suitable for industry. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim

This work presents a modification approach and first measurements of commercial cylindrical Li-ion cells with multiple local potential probes and an internal temperature sensor. Local potential measurements at low currents show a non-uniform potential distribution along the electrode, dominated by the open circuit voltage (OCV) of the negative electrode. For higher currents, the overpotential along the current collector becomes dominant and instead of a corrugated potential distribution, a significant current dependent voltage gradient can be detected, indicating a highly non-uniform state of charge (SOC) distribution with increasing distance to the current collecting tab. After the discharge operation, a quick potential equalization can be witnessed which results in a non-detectable potential difference between the single electrode sections after 12 min, even though the overall cell voltage relaxation has not reached an equilibrium state yet. The presented modification approach combines the advantages of high quality industrial manufactured cells showing uniform coating thicknesses and packing density with the advantages of special tailor made cells for in situ measurements. Due to the low impact of the modification and its long-term stability, highly reproducible measurements can be conducted at different locations of the electrodes.

In this short review, we compare the kinetics of hydrogen desorption in vacuum to those involved in the electrochemical hydrogen evolution/oxidation reactions (HER/HOR) at two types of atomically smooth model surfaces: bare Ru(0001) and the same surface covered by a 1.1 atomic layer thick Pt film. Low/high H2 (D2) desorption rates at room temperature in vacuum quantitatively correspond to low/high exchange current densities for the HOR/HER in electrochemistry. In view of the “volcano plot” concept, these represent two surfaces that adsorb hydrogen atoms, Had, too strongly and too weakly, respectively. Atomically smooth, vacuum annealed model surfaces are the closest approximation to the idealized slab geometries typically studied by density functional theory (DFT). A predictive volcano plot based on DFT-based adsorption energies for the Had intermediates agrees well with the experiments if two things are considered: (i) the steady-state coverage of Had intermediates and (ii) local variations in film thickness. The sluggish HER/HOR kinetics of Ru(0001) allows for excellent visibility of cyclic voltammetry (CV) features even in H2-saturated solution. The CV switches between a Had- and a OHad-/Oad-dominated regime, but the presence of H2 in the electrolyte increases the Had-dominated potential window by a factor of two. Whereas in plain electrolyte two electrochemical adsorption processes compete in forming adlayers, it is one electrochemical and one chemical one in the case of H2-saturated electrolyte. We demonstrate and quantitatively explain that dissociative H2 adsorption is more important than H+ discharge for Had formation in the low potential regime on Ru(0001).

Thermal stability of charged LiCoO 2 cathodes with various surface areas of active material is investigated in order to quantify the effect of LiCoO 2 surface area on thermal stability of cathode. Thermogravimetric analyses and calorimetry have been conducted on charged cathodes with different active material surface areas. Besides reduced thermal stability, high surface area also changes the active material decomposition reaction and induces side reactions with additives. Thermal analyses of LiCoO 2 delithiated chemically without any additives or with a single additive have been conducted to elaborate the effect of particle size on side reactions. Stability of cathode–electrolyte system has been investigated by accelerating rate calorimetry (ARC). Arrhenius activation energy of cathode decomposition has been calculated as function of conversion at different surface area of active material.

The effect of lithium boron oxide (LBO) coating on the electrochemical performance of orthorhombic LiMnO2 (o-LiMnO2) cathode for lithium-ion batteries is investigated. o-LiMnO2 synthesized via solid state synthesis technique is modified with LBO addition. The presence of LBO is identified via Fourier transform infrared spectroscopy analysis. o-LiMnO2 is observed to transform to a spinel-like phase during cycling which undergoes capacity fading. Studies indicate that the presence of 1–2 wt% LBO results in an improved capacity and better capacity retention with cycling. The pristine sample reveals a maximum specific capacity of 172 mAhg−1, whereas the LBO-modified samples display about 189.1 mAhg−1 in the cycling tests conducted at a rate of 50 mAg−1 in the voltage range of 2–4.5 V. After 70 cycles, the LBO-modified LiMnO2 displayed higher capacity retention of 175 mAhg−1 as compared to the pristine sample that exhibited 130 mAhg−1. By analyzing the charge–discharge behavior, it is observed that the capacity obtained from lithium insertion into the tetrahedral sites of the spinel structure is more or less constant throughout the cycling and that the bulk of the capacity loss is resulting when lithium is inserted into the octahedral sites of the spinel structure. Impedance measurement reveals a reduced charge-transfer resistance for the LBO-modified samples suggesting that the presence of LBO is countering capacity loss arising from insertion of lithium into the octahedral sites thus contributing to the overall cycling stability.

In laboratory experiments, Li-O2 systems show "sudden death" at capacities far below the theoretical value. Identifying how discharge products limit the total capacity is crucial in Li-O2 system. We investigated the effect of Li2O2 seed layer deposited on carbon cathode under potentiostatic conditions at increasing overpotentials to the subsequent slow discharge at galvanostatic condition. The discharge capacity attainable in the second step is found to vary by more than a factor of 3 depending on the history, i.e., the seed layer. These results provide evidence that the battery history is decisive for the total discharge capacities.

The solid electrolyte interphase that forms on graphite anodes plays a vital role in the performance of lithium-ion batteries. Now research shows that the formation of lithium fluoride deposits — one of the main components of the solid electrolyte interphase — is strongly influenced by the electrocatalytic activity of the anode.

The effect of temperature on the kinetics of electrochemical insertion/removal of lithium in graphite is analyzed by kinetic Monte Carlo methods. Different electrochemical techniques are simulated at different temperatures and responses are compared with experimental results. Simulated voltammograms show, similarly to experiment, how the behavior of the system becomes closer to equilibrium as temperature increases. Calculated chronoamperometric profiles show a different qualitative behavior in the current at different temperatures, especially in the Cottrell representation peaks, explained in terms of the relative importance of diffusive versus charge transfer processes at different temperatures. Results at room temperature are in good agreement with experiment, and we further evaluate trends at elevated temperature that have not yet been described in experimental or theoretical works. Exchange current densities for different degrees of lithium intercalation at different temperatures are predicted using potentiostatic simulations, showing an Arrhenius-type relationship. The dependence of the exchange current on electrolyte composition is simulated by investigating the effect of different activation energy barriers at different temperatures. The influence of temperature on diffusion coefficients as a function of lithiation fraction in graphite is simulated and related to Arrhenius plots, explaining the experimentally observed changes in diffusion phenomena with lithium composition and temperature. Fil: Gavilán Arriazu, Edgardo Maximiliano. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Córdoba. Instituto de Investigaciones en Físico-química de Córdoba. Universidad Nacional de Córdoba. Facultad de Ciencias Químicas. Instituto de Investigaciones en Físico-química de Córdoba; Argentina. Universidad Nacional de Santiago del Estero. Instituto de Bionanotecnología del Noa. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Tucumán. Instituto de Bionanotecnología del Noa; Argentina. Universidad Nacional de Córdoba. Facultad de Ciencias Químicas. Departamento de Química Teórica y Computacional; Argentina Fil: Mercer, Michael. Centre National de la Recherche Scientifique; Francia. Lancaster University. Department of Chemistry; Reino Unido. ALISTORE European Research Institute; Francia. The Faraday Institution; Reino Unido Fil: Pinto, Oscar Alejandro. Universidad Nacional de Santiago del Estero. Instituto de Bionanotecnología del Noa. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Tucumán. Instituto de Bionanotecnología del Noa; Argentina Fil: Oviedo, Oscar Alejandro. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Córdoba. Instituto de Investigaciones en Físico-química de Córdoba. Universidad Nacional de Córdoba. Facultad de Ciencias Químicas. Instituto de Investigaciones en Físico-química de Córdoba; Argentina Fil: Barraco Diaz, Daniel Eugenio. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Córdoba. Instituto de Física Enrique Gaviola. Universidad Nacional de Córdoba. Instituto de Física Enrique Gaviola; Argentina. Universidad Nacional de Córdoba. Facultad de Matemática, Astronomía y Física; Argentina Fil: Hoster, Harry Ernst. Centre National de la Recherche Scientifique; Francia. Lancaster University. Department of Chemistry; Reino Unido. ALISTORE European Research Institute; Francia. The Faraday Institution; Reino Unido Fil: Leiva, Ezequiel Pedro M.. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Córdoba. Instituto de Investigaciones en Físico-química de Córdoba. Universidad Nacional de Córdoba. Facultad de Ciencias Químicas. Instituto de Investigaciones en Físico-química de Córdoba; Argentina. Universidad Nacional de Córdoba. Facultad de Ciencias Químicas. Departamento de Química Teórica y Computacional; Argentina

Understanding the role of the phase transitions during lithiation and delithiation of graphite remains a problem of fundamental importance, but also practical relevance owing to its widespread use as the anode material in most commercial lithium-ion cells. Previously performed density functional theory (DFT) calculations show a rapid change in the lithium-carbon interaction at low occupation, due to partial charge transfer from Li to C. We integrate this effect in our previously developed two level mean field model, which describes the Stage I – Stage II transition in graphite. The modified model additionally describes the most predominant transition that occurs at low Li content in graphite, which results in a previously unexplained feature in voltage and dQ/dV profiles, and thermodynamic measurements of partial molar enthalpy. In contrast with the Stage I-Stage II transition, this extra feature is not associated with observable features in the partial molar entropy and our model demonstrates why. There is a sharp change in the open circuit voltage at very low Li occupation, followed by a transition to a voltage plateau (peak in dQ/dV). The behaviour arises due to the contrasting effects of the partial molar entropy and enthalpy terms on the partial molar Gibbs energy and hence cell voltage. Hence the voltage profile and phase transitions can be approximated for all lithium occupations, potentially allowing a predictive capability in cell level models. Fil: Mercer, Michael. Lancaster University; Reino Unido. Centre National de la Recherche Scientifique; Francia. ALISTORE European Research Institute; Francia. The Faraday Institution; Reino Unido Fil: Otero, Manuel. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Córdoba. Instituto de Investigaciones en Físico-química de Córdoba. Universidad Nacional de Córdoba. Facultad de Ciencias Químicas. Instituto de Investigaciones en Físico-química de Córdoba; Argentina. Universidad Nacional de Córdoba. Facultad de Ciencias Químicas. Departamento de Química Teórica y Computacional; Argentina. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Córdoba. Instituto de Física Enrique Gaviola. Universidad Nacional de Córdoba. Instituto de Física Enrique Gaviola; Argentina. Universidad Nacional de Córdoba. Facultad de Matemática, Astronomía y Física; Argentina Fil: Ferrer Huerta, Miriam. Centre National de la Recherche Scientifique; Francia. The Faraday Institution; Reino Unido Fil: Sigal, Agustín. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Córdoba. Instituto de Investigaciones en Físico-química de Córdoba. Universidad Nacional de Córdoba. Facultad de Ciencias Químicas. Instituto de Investigaciones en Físico-química de Córdoba; Argentina. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Córdoba. Instituto de Física Enrique Gaviola. Universidad Nacional de Córdoba. Instituto de Física Enrique Gaviola; Argentina Fil: Barraco Diaz, Daniel Eugenio. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Córdoba. Instituto de Física Enrique Gaviola. Universidad Nacional de Córdoba. Instituto de Física Enrique Gaviola; Argentina Fil: Hoster, Harry Ernst. Centre National de la Recherche Scientifique; Francia. ALISTORE European Research Institute; Francia. The Faraday Institution; Reino Unido. ALISTORE European Research Institute; Francia Fil: Leiva, Ezequiel Pedro M.. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Córdoba. Instituto de Investigaciones en Físico-química de Córdoba. Universidad Nacional de Córdoba. Facultad de Ciencias Químicas. Instituto de Investigaciones en Físico-química de Córdoba; Argentina. Universidad Nacional de Córdoba. Facultad de Ciencias Químicas. Departamento de Química Teórica y Computacional; Argentina

The capacity and energy density of Na3V2(PO4)3 cathode material, for sodium ion batteries, was enhanced by partial substitution of iron in the octahedral vanadium site. Through this process, we show for the first time that the V4+/V5+ redox couple can be utilized in rhombohedral NASICON at above 4.0V vs. Na/Na+. At this juncture, we discovered that iron is unique in its ability to easily activate vanadium’s highest oxidation state. Furthermore, an additional 12% capacity is realized due to the increased sodium concentration in the synthesized compound.

A facile two-step strategy involving a polyol method and subsequent thermal annealing treatment is successfully developed for the general synthesis of metal oxide/carbon coaxial nanocables. Benefitting from the strong coupling effect, these hybrid nanocables exhibit remarkable lithium storage properties with high capacity, long cycle life and excellent rate capability.

We report on the synthesis and the properties of N,N,N′,N′-tetramethyl-N′′,N′′-pentamethyleneguanidinium bis(trifluoromethylsulfonyl)imide (PipGuan-TFSI). The cation of this novel ionic liquid combines guanidinium and piperidinium structural elements. We tested it for its viscosity, ion conductivity, and also for its thermal and electrochemical stability. Furthermore, a 0.5 M solution of lithium TFSI in PipGuan-TFSI was tested as an electrolyte for Li-ion batteries. These experiments included cycles of Li deposition/dissolution on stainless steel and (de)intercalation into/from LiFePO4 electrodes. The tests involving LiFePO4 cathodes were performed at various C-rates and temperatures for a better quantitative comparison to other electrolyte systems. We discuss in how far PipGuan-TFSI successfully combines the advantages of guanidinium and piperidinium ionic liquids for battery electrolyte applications.

The electrocatalytic activity of different, structurally well defined bimetallic PtRu surfaces in the oxygen reduction reaction was investigated by a combination of scanning tunnelling microscopy and electrochemical measurements performed under controlled mass transport conditions in a flow cell. We compare the effect of pseudomorphic Pt cover layers, mimicking the situation in a core–shell Pt/Ru nanoparticle, and of mixed PtxRu1−x monolayer surface alloys, reflecting the situation in an alloyed nanoparticle. The results unambiguously demonstrate that these bimetallic surfaces can reach activities well in excess of that of Pt(111), both for the film surfaces and the surface alloys, by optimizing the Pt surface content (surface alloys) or the Pt film thickness (film surfaces). The results are compared with simulated kinetic current–potential profiles based on existent density functional theory calculations (Greeley and Norskov, J Phys Chem C 113:4932, 2009; Lischka et al., Electrochim Acta 52:2219, 2007) revealing very good agreement in trends. Potential and limits of this approach are discussed.

Various two-dimensional (2D) materials have recently attracted great attention owing to their unique properties and wide application potential in electronics, catalysis, energy storage, and conversion. However, large-scale production of ultrathin sheets and functional nanosheets remains a scientific and engineering challenge. Here we demonstrate an efficient approach for large-scale production of V2O5 nanosheets having a thickness of 4 nm and utilization as building blocks for constructing 3D architectures via a freeze-drying process. The resulting highly flexible V2O5 structures possess a surface area of 133 m(2) g(-1), ultrathin walls, and multilevel pores. Such unique features are favorable for providing easy access of the electrolyte to the structure when they are used as a supercapacitor electrode, and they also provide a large electroactive surface that advantageous in energy storage applications. As a consequence, a high specific capacitance of 451 F g(-1) is achieved in a neutral aqueous Na2SO4 electrolyte as the 3D architectures are utilized for energy storage. Remarkably, the capacitance retention after 4000 cycles is more than 90%, and the energy density is up to 107 W·h·kg(-1) at a high power density of 9.4 kW kg(-1).

We report on the electrochemical properties of layered manganese oxides, with and without cobalt substituents, as cathodes in sodium ion batteries. We fabricated sub-micrometre-sized particles of Na0.7MnO2 + z and Na0.7Co0.11Mn0.89O2 + z via combustion synthesis. X-ray diffraction revealed the same layered hexagonal P2-type bronze structure with high crystallinity for both materials. Potentiostatic and galvanostatic charge/discharge cycles in the range 1.5–3.8 V vs. Na | Na+ were performed to identify potential-dependent phase transitions, capacity, and capacity retention. After charging to 3.8 V, both materials had an initial discharge capacity of 138 mA h g−1 at a rate of 0.3 C. For the 20th cycle, those values reduced to 75 and 92 mA h g−1 for Co-free and Co-doped samples, respectively. Our findings indicate that earlier works probably underestimated the potential of (doped) P2-type Na0.7MnO2 + z as cathode material for sodium ion batteries in terms of capacity and cycle stability. Apart from doping, a simple optimization parameter seems to be the particle size of the active material.

The influence of cell temperature on the current density distribution and accompanying inhomogeneities in state of charge (SOC) during cycling is analyzed in this work. To allow for a detailed insight in the electrochemical behavior of the cell, commercially available 26650 cells were modified to allow for measuring local potentials at four different, nearly equidistant positions along the electrodes. As a follow-up to our previous work investigating local potentials within a cell, we apply this method for studying SOC deviations and their sensitivity to cell temperature. The local potential distribution was studied during constant current discharge operations for various current rates and discharge pulses in order to evoke local inhomogeneities for temperatures ranging from 10 °C to 40 °C. Differences in local potentials were considered for estimating local SOC variations within the electrodes. It could be observed that even low currents such as 0.1C can lead to significant inhomogeneities, whereas a higher cell temperature generally results in more pronounced inhomogeneities. A rapid SOC equilibration can be observed if the variation in the SOC distribution corresponds to a considerable potential difference defined by the open circuit voltage of either the positive or negative electrode. With increasing temperature, accelerated equalization effects can be observed.

In this work, modified commercial cylindrical lithium-ion cells with multiple separate current tabs are used to analyze the influence of tab pattern, frequency and temperature on electrochemical impedance spectroscopy. In a first step, the effect of different current tab arrangements on the impedance spectra is analyzed and possible electrochemical causes are discussed. In a second step, one terminal is used to apply a sinusoidal current while the other terminals are used to monitor the local potential distribution at different positions along the electrodes of the cell. It is observed that the characteristic decay of the voltage amplitude along the electrode changes non-linearly with frequency, where high-frequent currents experience a stronger attenuation along the current collector than low-frequent currents. In further experiments, the decay characteristic is controlled by the cell temperature, driven by the increasing resistance of the current collector and the enhanced kinetic and transport properties of the active material and electrolyte. Measurements indicate that the ac current distribution depends strongly on the frequency and the temperature. In this context, the challenges for electrochemical impedance spectroscopy as cell diagnostic technique for commercial cells are discussed.

Investigating the dynamics in an adlayer of the oligopyridine derivative 2-phenyl-4,6-bis(6-(pyridine-2-yl)-4-(pyridine-4-yl)pyridine-2-yl)pyrimidine (2,4'-BTP) on Ag(111) by fast scanning tunneling microscopy (video-STM), we found that rotating 2,4'-BTP adsorbates coexist in a two-dimensional (2D) liquid phase (beta-phase) in a dynamic equilibrium with static adsorbate molecules. Furthermore, exchange between an ordered phase (a-phase) and beta-phase leads to fluctuations of the domain boundary on a time scale of seconds. Quantitative evaluation of the temperature-dependent equilibrium between rotating and static adsorbates, evaluated from a large number of STM images, gains insight into energetic and entropic stabilization and underlines that the rotating adsorbate molecules are stabilized by an entropy contribution, which is compatible with that derived by using statistical mechanics. The general validity of the concept of entropic stabilization of rotating admolecules, favoring rotation already at room temperature, is tested for other typical small, mid-size and large adsorbates.

The reaction of O(2) with an adlayer of the oligopyridine 2-phenyl-4,6-bis(6-(pyridine-2-yl)-4-(pyridine-4-yl)-pyridine-2-yl)pyrimidine (2,4'-BTP), adsorbed on the (111) surfaces of silver and gold and on HOPG--which can be considered as a model system for inorganic|organic contacts--was investigated by fast scanning tunneling microscopy (video STM) and dispersion corrected density functional theory (DFT-D) calculations. Only on Ag(111), oxidation of the 2,4'-BTP adlayer was observed, which is related to the fact that under the experimental conditions O(2) adsorbs dissociatively on this surface leading to reactive O adatoms, but not on Au(111) or HOPG . There is a distinct regiospecifity of the oxidation reaction caused by intermolecular interactions. In addition, the oxidation leads to a chiral ordering. The relevance of these findings for reactions involving organic monolayers is discussed.

The competition between intermolecular interactions and long-range lateral variations in the substrate–adsorbate interaction was studied by scanning tunnelling microscopy (STM) and force field based calculations, by comparing the phase formation of (sub-) monolayers of the organic molecules (i) 2-phenyl-4,6-bis(6-(pyridin-3-yl)-4-(pyridin-3-yl)pyridin-2-yl)pyrimidine (3,3'-BTP) and (ii) 3,4,9,10-perylene tetracarboxylic-dianhydride (PTCDA) on graphene/Ru(0001). For PTCDA adsorption, a 2D adlayer phase was formed, which extended over large areas, while for 3,3'-BTP adsorption linear or ring like structures were formed, which exclusively populated the areas between the maxima of the moiré structure of the buckled graphene layer. The consequences for the competing intermolecular interactions and corrugation in the adsorption potential are discussed and compared with the theoretical results.