Search

The X-IFU is the cryogenic spectrometer onboard the future ATHENA X-ray observatory. It is based on a large array of TES microcalorimeters, which works in combination with a Cryogenic AntiCoincidence detector (CryoAC). This is necessary to reduce the particle background level thus enabling part of the mission science goals. Here we present the first joint test of X-IFU TES array and CryoAC Demonstration Models, performed in a FDM setup. We show that it is possible to operate properly both detectors, and we provide a preliminary demonstration of the anti-coincidence capability of the system achieved by the simultaneous detection of cosmic muons., Comment: Accepted for publication in the Journal of Low Temperature Physics for LTD-19 special issue

In the frequency-domain multiplexing (FDM) scheme, transition-edge sensors (TES) are individually coupled to superconducting LC filters and AC biased at MHz frequencies through a common readout line. To make efficient use of the available readout bandwidth and to minimize the effect of non-linearities, the LC resonators are usually designed to be on a regular grid. The lithographic processes however pose a limit on the accuracy of the effective filter resonance frequencies. Off-resonance bias carriers could be used to suppress the impact of intermodulation distortions, which nonetheless would significantly affect the effective bias circuit and the detector spectral performance. In this paper we present a frequency shift algorithm (FSA) to allow off-resonance readout of TES's while preserving the on-resonance bias circuit and spectral performance, demonstrating its application to the FDM readout of a X-ray TES microcalorimeter array. We discuss the benefits in terms of mitigation of the impact of intermodulation distortions at the cost of increased bias voltage and the scalability of the algorithm to multi-pixel FDM readout. We show that with FSA, in multi-pixel and frequencies shifted on-grid, the line noises due to intermodulation distortion are placed away from the sensitive region in the TES response and the X-ray performance is consistent with the single-pixel, on-resonance level., Comment: Accepted for publication on Review of Scientific Instruments

Athena is a space-based X-ray observatory intended for exploration of the hot and energetic universe. One of the science instruments on Athena will be the X-ray Integrated Field Unit (X-IFU), which is a cryogenic X-ray spectrometer, based on a large cryogenic imaging array of Transition Edge Sensors (TES) based microcalorimeters operating at a temperature of 100mK. The imaging array consists of 3800 pixels providing 2.5 eV spectral resolution, and covers a field of view with a diameter of of 5 arc minutes. Multiplexed readout of the cryogenic microcalorimeter array is essential to comply with the cooling power and complexity constraints on a space craft. Frequency domain multiplexing has been under development for the readout of TES-based detectors for this purpose, not only for the X-IFU detector arrays but also for TES-based bolometer arrays for the Safari instrument of the Japanese SPICA observatory. This paper discusses the design considerations which are applicable to optimise the multiplex factor within the boundary conditions as set by the space craft. More specifically, the interplay between the science requirements such as pixel dynamic range, pixel speed, and cross talk, and the space craft requirements such as the power dissipation budget, available bandwidth, and electromagnetic compatibility will be discussed.

The Athena+ mission concept is designed to implement the Hot and Energetic Universe science theme submitted to the European Space Agency in response to the call for White Papers for the definition of the L2 and L3 missions of its science program. The Athena+ science payload consists of a large aperture high angular resolution X-ray optics and twelve meters away, two interchangeable focal plane instruments: the X-ray Integral Field Unit (X-IFU) and the Wide Field Imager (WFI). The X-IFU is a cryogenic X-ray spectrometer, based on a large array of Transition Edge Sensors (TES), offering 2.5 eV spectral resolution, with ~5" pixels, over a field of view of 5 arc minutes in diameter. In this paper, we briefly describe the Athena+ mission concept and the X-IFU performance requirements. We then present the X-IFU detector and readout electronics principles, the current design of the focal plane assembly, the cooling chain and review the global architecture design. Finally, we describe the current performance estimates, in terms of effective area, particle background rejection, count rate capability and velocity measurements. Finally, we emphasize on the latest technology developments concerning TES array fabrication, spectral resolution and readout performance achieved to show that significant progresses are being accomplished towards the demanding X-IFU requirements., Comment: Supporting paper for the science theme "The Hot and Energetic Universe" to be implemented by the Athena+ X-ray observatory (http://www.the-athena-x-ray-observatory.eu). 17 pages, 19 figures

ORIGIN is a proposal for the M3 mission call of ESA aimed at the study of metal creation from the epoch of cosmic dawn. Using high-spectral resolution in the soft X-ray band, ORIGIN will be able to identify the physical conditions of all abundant elements between C and Ni to red-shifts of z=10, and beyond. The mission will answer questions such as: When were the first metals created? How does the cosmic metal content evolve? Where do most of the metals reside in the Universe? What is the role of metals in structure formation and evolution? To reach out to the early Universe ORIGIN will use Gamma-Ray Bursts (GRBs) to study their local environments in their host galaxies. This requires the capability to slew the satellite in less than a minute to the GRB location. By studying the chemical composition and properties of clusters of galaxies we can extend the range of exploration to lower redshifts (z ~ 0.2). For this task we need a high-resolution spectral imaging instrument with a large field of view. Using the same instrument, we can also study the so far only partially detected baryons in the Warm-Hot Intergalactic Medium (WHIM). The less dense part of the WHIM will be studied using absorption lines at low redshift in the spectra for GRBs., Comment: 34 pages, 13 figures. ESA Cosmic Vision medium-class mission (M3) proposal. Accepted for publication in Experimental Astronomy. Including minor corrections in the author list

The CoRoT satellite exoplanetary team announces its sixth transiting planet in this paper. We describe and discuss the satellite observations as well as the complementary ground-based observations - photometric and spectroscopic - carried out to assess the planetary nature of the object and determine its specific physical parameters. The discovery reported here is a `hot Jupiter' planet in an 8.9d orbit, 18 stellar radii, or 0.08 AU, away from its primary star, which is a solar-type star (F9V) with an estimated age of 3.0 Gyr. The planet mass is close to 3 times that of Jupiter. The star has a metallicity of 0.2 dex lower than the Sun, and a relatively high $^7$Li abundance. While thelightcurveindicatesamuchhigherlevelof activity than, e.g., the Sun, there is no sign of activity spectroscopically in e.g., the [Ca ] H&K lines.

Earth-sized planets around nearby stars are being detected for the first time by ground-based radial velocity and space-based transit surveys. This milestone is opening the path towards the definition of missions able to directly detect the light from these planets, with the identification of bio-signatures as one of the main objectives. In that respect, both ESA and NASA have identified nulling interferometry as one of the most promising techniques. The ability to study distant planets will however depend on exozodiacal dust clouds surrounding the target stars. In this paper, we assess the impact of exozodiacal dust clouds on the performance of an infrared nulling interferometer in the Emma X-array configuration. For the nominal mission architecture with 2-m aperture telescopes, we found that point-symmetric exozodiacal dust discs about 100 times denser than the solar zodiacal cloud can be tolerated in order to survey at least 150 targets during the mission lifetime. Considering modeled resonant structures created by an Earth-like planet orbiting at 1 AU around a Sun-like star, we show that the tolerable dust density for planet detection goes down to about 15 times the solar zodiacal density for face-on systems and decreases with the disc inclination. The upper limits on the tolerable exozodiacal dust density derived in this study must be considered as rather pessimistic, but still give a realistic estimation of the typical sensitivity that we will need to reach on exozodiacal discs in order to prepare the scientific programme of future Earth-like planet characterisation missions., Comment: 17 pages, accepted for publication in A&A

Characterising the circumstellar dust around nearby main sequence stars is a necessary step in understanding the planetary formation process and is crucial for future life-finding space missions such as ESA's Darwin or NASA's Terrestrial Planet Finder (TPF). Besides paving the technological way to Darwin/TPF, the space-based infrared interferometers Pegase and FKSI (Fourier-Kelvin Stellar Interferometer) will be valuable scientific precursors in that respect. In this paper, we investigate the performance of Pegase and FKSI for exozodiacal disc detection and compare the results with ground-based nulling interferometers. Besides their main scientific goal (characterising hot giant extrasolar planets), Pegase and FKSI are very efficient in assessing within a few minutes the level of circumstellar dust in the habitable zone around nearby main sequence stars. They are capable of detecting exozodiacal discs respectively 5 and 1 time as dense as the solar zodiacal cloud and they outperform any ground-based instrument. Unlike Pegase, FKSI can achieve this sensitivity for most targets of the Darwin/TPF catalogue thanks to an appropriate combination of baseline length and observing wavelength. The sensitivity of Pegase could, however, be significantly boosted by considering a shorter interferometric baseline length. These space-based interferometers would be complementary to Antarctica-based instruments in terms of sky coverage and would be ideal instruments for preparing future life-finding space missions., Comment: 11 pages, accepted for publication in A&A

Nulling interferometry, a powerful technique for high-resolution imaging of the close neighbourhood of bright astrophysical objets, is currently considered for future space missions such as Darwin or the Terrestrial Planet Finder Interferometer (TPF-I), both aiming at Earth-like planet detection and characterization. Ground-based nulling interferometers are being studied for both technology demonstration and scientific preparation of the Darwin/TPF-I missions through a systematic survey of circumstellar dust disks around nearby stars. In this paper, we investigate the influence of atmospheric turbulence on the performance of ground-based nulling instruments, and deduce the major design guidelines for such instruments. End-to-end numerical simulations allow us to estimate the performance of the main subsystems and thereby the actual sensitivity of the nuller to faint exozodiacal disks. Particular attention is also given to the important question of stellar leakage calibration. This study is illustrated in the context of GENIE, the Ground-based European Nulling Interferometer Experiment, to be installed at the VLTI and working in the L' band. We estimate that this instrument will detect exozodiacal clouds as faint as about 50 times the Solar zodiacal cloud, thereby placing strong constraints on the acceptable targets for Darwin/TPF-I., Comment: A&A, accepted

A generalized model for the critical temperature Tc of superconducting bilayers is presented, which is valid with no restrictions to film thicknesses, Tc of the layers and interface resistivity. The model is verified experimentally on a series of Nb-Al and Ta-Al bilayers with Nb, Ta layer thicknesses of 100 nm and Al layer thicknesses ranging from 5 nm to 200 nm. Excellent agreement between theory and experiment was found for the energy gap and the Tc of bilayers. The results are important for designing practical superconducting devices., Comment: 3 pages, 2 figures

We recently predicted the formation of a highly non-equilibrium quasiparticle (qp) distribution in low TC multiple tunnelling superconducting tunnel junctions (STJs) [1]. The situation arises through qp energy gain in cycles of successive forward and back tunnelling events in the absence of relaxation via sub-gap phonon emission. The qps can acquire sufficient energy to emit phonons, which break more Cooper pairs and release additional qps. In this paper we report theoretical and experimental studies of the effect of this process on photon detection by such an STJ. We derived a set of energy-dependent balance equations [2], which describe the kinetics of the qps and phonons, including the qp multiplication process described above. Solution of the balance equations gives the non-equilibrium distribution of the qps as a function of time and energy, and hence the responsivity of the STJ as a function of bias voltage. We compared the theoretical results with experiments on high quality, multiple-tunnelling Al STJs cooled to 35mK in an adiabatic demagnetisation refrigerator, and illuminated with monochromatic photons with wavelengths between 250 and 1000 nm. It was found that in the larger junctions with the longest qp loss time, both responsivity and signal decay time increased rapidly with bias voltage. Excellent agreement was obtained between the observed effects and theoretical modelling., Comment: 8 pages, 6 figures

We describe a model for photon absorption by superconducting tunnel junctions in which the full energy dependence of all the quasiparticle dynamic processes is included. The model supersedes the well-known Rothwarf-Taylor approach, which becomes inadequate for a description of the small gap structures that are currently being developed for improved detector resolution and responsivity. In these junctions relaxation of excited quasiparticles is intrinsically slow so that the energy distribution remains very broad throughout the whole detection process. By solving the energy-dependent kinetic equations describing the distributions, we are able to model the temporal and spectral evolution of the distribution of quasiparticles initially generated in the photo-absorption process. Good agreement is obtained between the theory and experiment., Comment: 25 pages, 15 figures

A 6x6 array of symmetrical V/Al/AlOx/Al/V Superconducting Tunnel Junctions (STJs) was fabricated. The base electrode is a high quality epitaxial film with a residual resistance ratio (RRR) of ~30. The top film is polycrystalline with an RRR of ~10. The leakage currents of the 25x25 mm^2 junctions are of the order of 0.5 pA/mm^2 at a bias voltage of 100 mV, which corresponds to a dynamical resistance of ~ 3 10^5 ohms. When the array was illuminated by 6 keV X-ray photons from a 55Fe radioactive source the single photon charge output was found to be low and strongly dependent on the temperature of the devices. This temperature dependence at X-ray energies can be explained by the existence of a very large number of quasiparticle (QP) traps in the Vanadium. QPs are confined in these traps, having a lower energy gap than the surrounding material, and are therefore not available for tunneling. The number of traps can be derived from the energy dependence of the responsivity of the devices (charge output per electron volt of photon input energy)., Comment: 4 pages. presented at Low Temperature Detectors-9

Cryogenic soft X-ray imaging spectrometers are currently being developed for applications in the fields of Astronomy and material sciences. In this paper we present experiments on optimized single devices, which show measured energy resolutions of 4.6 eV at 525 eV, 8.1 eV at 1.5 keV and 20.5 eV at 6 keV respectively. These energy resolutions combined with a quantum efficiency of more than 40 % in the energy range from 0.5 to 2 keV together with a count rate capability of 15 kHz demonstrate the overall good performance of single Superconducting Tunnel Junctions (STJs). Assembling these optimized single devices in a matrix read-out would provide the practical basis for a soft X-ray imaging spectrometer., Comment: 4 pages, presented at Applied Superconductivity Conference 2000

Generic properties of elastic phonon transport at a disordered interface are studied. The results show that phonon transmittance is a strong function of frequency and the disorder correlation length. At frequencies lower than the van Hove singularity the transmittance at a given frequency increases as the correlation length decreases. At low frequencies, this is reflected by different power-laws for phonon conductance across correlated and uncorrelated disordered interfaces which are in approximate agreement with perturbation theory of an elastic continuum. These results can be understood in terms of simple mosaic and two-colour models of the interface., Comment: 17 pages, 5 figures, submitted to PRB

We summarize several results based on the velocity data-set for cluster galaxies provided by ENACS (the ESO Nearby Abell Cluster Survey). We describe the distribution of velocity dispersions of a complete sample of rich galaxy clusters, and compare it to the distribution of cluster X-ray temperatures, and with predictions of theoretical models. We then address the issue of the existence of a Fundamental Plane (FP) for rich clusters, first suggested by Schaeffer et al. We confirm the existence of this FP with the ENACS data-set. The cluster FP is different from the FP of elliptical galaxies, and from the virial prediction. Some implications of the cluster FP are discussed. Finally, we describe the phase-space distributions of different populations of cluster galaxies. Different galaxy classes are defined according to their morphological or spectral type, and the presence of emission-lines. Star-forming (late-type) galaxies have a velocity dispersion profile that (in combination with their wider spatial distribution) is suggestive of first infall into the cluster. On the contrary, quiescent (early-type) galaxies show evidence of a dynamically relaxed distribution., Comment: 13 pages, 6 figures, to appear in the proceedings of 'Observational Cosmology: The Developments of Galaxy Systems', Sesto 1998

Summary - By combining the 5634 redshifts from the ESO Nearby Abell Cluster Survey (the ENACS) with another 1000 redshifts from the literature we are able to study the distribution of velocity dispersions for a volume-limited sample of 128 $R_{\rm ACO} \geq 1$ clusters, out to a redshift $z=0.1$, in a solid angle of 2.55 sr centered on the South Galactic Pole. In deriving velocity dispersions we apply a new, physically motivated method for removing fore- and background galaxies. We discuss in detail the completeness of the cluster sample for which we derive the distribution of cluster velocity dispersions. The large apparent spread between velocity dispersion and richness must be largely intrinsic. A consequence of the very broad relation between richness and velocity dispersion is that all cluster samples complete in richness are biased against low dispersions. For the richness limit of our sample this bias operates below about 800 km/sec. Above 800 km/s, our distribution of global velocity dispersions is free from systematic errors and biases, and agrees very well with the most recent determination of the distribution of cluster X-ray temperatures. Therefore, we conclude that X-ray temperature and velocity dispersion distributions statistically measure the same cluster property. We stress the need for model predictions that produce exactly the same information as provided by the observations, for a sample of model clusters with a richness limit that mimics that of the sample of observed clusters., Comment: accepted by A&A; LateX file (no figures). Complete uuencoded Z-compressed postscript file available via anonymous ftp at ftp://strw.leidenuniv.nl/pub/katgert/paper2.uu (132.229.80.1), or at ftp://lasm0b.astrsp-mrs.fr/amazure/papers/enacs2.uu (193.50.128.3) (VMS server)

Summary - By using the data from the ESO Nearby Abell Cluster Survey (ENACS), we have studied the properties of emission-line galaxies (ELG) in clusters. The fraction of ELG in clusters is 16~\%; this fraction is slightly dependent on the cluster velocity dispersion, being larger for ``colder'' systems. ELG tend to occur more frequently than other cluster galaxies in substructures. However, only a minor cluster fraction has an ELG population with a mean velocity significantly different from that of the overall cluster population. The velocity distribution of cluster ELG is broader than that of the other cluster galaxies, which translates in a larger observed velocity dispersion. The velocity distribution for ELG in the inner cluster regions suggests that ELG are on mostly radial orbits., Comment: gzipped postscript file; to appear in the proceedings of the international workshop: "Observational Cosmology: from Galaxies to Galaxy Systems", Sesto, Italy, 4-7 July 1995, special issue of Astrophysical Letters and Communications, G.C.C.Palumbo ed

Summary - We describe the results of the ESO Key-programme on `Structure and Dynamics of Rich Galaxy Clusters' (or ENACS). The final database contains a total of 5634 galaxies in the directions of 107 clusters from the ACO catalogue with richness $R\ge 1$ and mean redshifts $z \le 0.1$. Of the 5634 redshifts, 4465 are based on absorption lines only, 583 on emission lines only and 586 on both. The overall reliability of the 5634 accepted redshifts is 0.98. For 5615 galaxies an $R_{25}$ magnitude was obtained. We discuss various methods for defining the compact, physically relevant systems in the 107 `pencil-beam' surveys. We have chosen to apply a fixed velocity gap of 1000 km/s to separate galaxies that do not form part of the same system. With this gap size, systems are not broken up into sub-systems, and field galaxies are hardly linked to the systems. We present the mean redshifts of the 220 systems (with at least 4 members) identified in the 107 pencil beam surveys. On average, about 75~\% of the 5634 galaxies are in the largest system found in the direction of the rich Abell cluster candidate. Half of the 25~\% of galaxies outside the largest system belong to a secondary system along the same line of sight. For about 90~\% of the nearby rich Abell cluster candidates studied here we find a redshift system that either contains more than half of the total number of redshifts, or that has at least two times as many redshifts as the next largest system., Comment: accepted by A&A; LateX file (no figures). Complete uuencoded Z-compressed postscript file available via anonymous ftp at ftp://strw.leidenuniv.nl/pub/katgert/paper1.uu (132.229.80.1), or at ftp://lasm0b.astrsp-mrs.fr/amazure/papers/enacs1.uu (193.50.128.3) (VMS server)

In this paper we present a first assessment of the impact of various forms of instrumental crosstalk on the science performance of the X-ray Integral Field Unit (X-IFU) on the Athena X-ray mission. This assessment is made using the SIXTE end-to-end simulator in the context of one of the more technically challenging science cases for the XIFU instrument. Crosstalk considerations may influence or drive various aspects of the design of the array of high-count-rate Transition Edge Sensor (TES) detectors and its Frequency Domain Multiplexed (FDM) readout architecture. The Athena X-ray mission was selected as the second L-class mission in ESA's Cosmic Vision 2015–25 plan, with alaunch foreseen in 2028, to address the theme ''Hot and Energetic Universe"1. One of the two instruments on boardAthena is the X-ray Integral Field Unit2 (X-IFU) which is based on an array of ~3800 Transition Edge Sensors (TES's)operated at a temperature of ~90 mK. The science cases pose an interesting challenge for this instrument, as they requirea combination of high energy resolution (2.5 eV FWHM or better), high spatial resolution (5 arcsec or better) and highcount rate capability (several tens of counts per second per detector for point sources as bright as 10 mCrab).The performance at the single sensor level has been demonstrated3, but the operation of such detectors in an array, usingmultiplexed readout, brings additional challenges, both for the design of the array in which the sensors are placed and forthe readout of the sensors. The readout of the detector array will be based on Frequency Domain Multiplexing (FDM)4.In this system of detectors and readout, crosstalk can arise through various mechanisms: on the TES array, neighboringsensors can couple through thermal crosstalk. Detectors adjacent in carrier frequency may suffer from electrical crosstalkdue to the finite width of the bandpass filters, and shared sources of impedance in their signal lines. The signals from theindividual detectors are summed and then amplified by a pair of SQUID amplifiers before being sent to warm front-endelectronics. The transfer function of the SQUID amplifiers is non-linear, which will give rise to higher harmonics ofcarriers and intermodulation products when multiple signal pulses are simultaneously present in the SQUID. Under highcount rate conditions this is another source of crosstalk. The effect of all these crosstalk sources is that parasitic pulseswill appear in the record of a signal pulse which will create a stochastic offset of the measured energy and thus adegradation of the energy resolution.