Search

The incorporation of gold nanoparticles within thermally responsive poly( N-isopropyl acrylamide) hydrogels provides a simple means to define photothermally addressable materials. Relying on such composite gels, it is established here that micropatterned bilayer photoactuators demonstrate rapid and highly reversible bending and unbending behavior in response to illumination with visible light. In addition to actuation by free space light, as in most previous research on such responsive nanocomposite hydrogels, light from a 532 nm laser is also waveguided through a plastic optical fiber directly into the photoactuator, providing remotely controllable actuators that do not require line-of-sight access. [ABSTRACT FROM AUTHOR]

Patterns of white light are projected on liquid crystal (LC) polymer films containing gold nanospheres (NS) or nanorods (NR) to induce out-of-plane buckling through a photothermal effect. Straightforward synthetic techniques are used to provide well-dispersed nanocomposite films, with NRs exhibiting self-alignment with the LC director. Using a combination of prepatterned director orientation and spatiotemporal variations in light intensity, these nanocomposite films can be reversibly configured into different 3D states. Fine control over shape is demonstrated through variations in size, shape, and intensity of the illuminated region. Switching time scales are found to be of order a few seconds or below, likely reflecting the intrinsic relaxation time of the LC materials. [ABSTRACT FROM AUTHOR]

ABSTRACT A simple method to achieve dispersion of nanoparticles (NPs) within polymer matrices by solution-state photografting of benzophenone (BP)-containing random copolymers is presented. A benzyl ether ligand that stabilizes NPs in solution while possessing selectivity toward hydrogen abstraction and subsequent coupling with BP was designed. This method for introducing grafts by ultraviolet (UV) light exposure affords control over the dispersion state in the resulting polymer films, as revealed by transmission electron microscopy and UV-visible spectroscopy. The evolution of the hydrodynamic sizes of particles as a function of UV dose suggests that the polymers 'wrap' particles by forming multiple attachment points per chain because of the relatively rapid kinetics for the formation of subsequent attachments following the first grafting event for a given chain. In addition, the presence of unreacted BP groups allows for photolithographic patterning of well-dispersed nanocomposite films. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 152-158 [ABSTRACT FROM AUTHOR]

Patterning deformation within the plane of thin elastic sheets represents a powerful tool for the definition of complex and stimuli-responsive 3D buckled shapes. Previous experimental methods, however, have focused on sheets that access a limited number of shapes pre-programmed into the sheet, restricting the degree of dynamic control. Here, we demonstrate on-demand reconfigurable buckling of poly( N-isopropylacrylamide- co-acrylic acid) (PNIPAM) hydrogel network films containing gold nanoparticles (AuNPs) by patterned photothermal deswelling. Predictable, easily controllable, and reversible transformations from a single flat gel sheet to numerous different three-dimensional forms are shown. Importantly, the response time is limited by poroelastic mass transport, rather than photochemical switching kinetics, enabling reconfiguration of shape on timescales of several seconds, with further increases in speed possible by reducing film thickness. [ABSTRACT FROM AUTHOR]

Patterning deformation within the plane of thin elastic sheets represents a powerful tool for the definition of complex and stimuli-responsive 3D buckled shapes. Previous experimental methods, however, have focused on sheets that access a limited number of shapes pre-programmed into the sheet, restricting the degree of dynamic control. Here, we demonstrate on-demand reconfigurable buckling of poly( N-isopropylacrylamide- co-acrylic acid) (PNIPAM) hydrogel network films containing gold nanoparticles (AuNPs) by patterned photothermal deswelling. Predictable, easily controllable, and reversible transformations from a single flat gel sheet to numerous different three-dimensional forms are shown. Importantly, the response time is limited by poroelastic mass transport, rather than photochemical switching kinetics, enabling reconfiguration of shape on timescales of several seconds, with further increases in speed possible by reducing film thickness. [ABSTRACT FROM AUTHOR]

We present a new class of tunable light-driven oscillators based on mm-scale objects adsorbed at fluid interfaces. A fixed light source induces photothermal surface tension gradients (Marangoni stresses) that drive nanocomposite hydrogel discs away from a stable apex position atop a drop of water. The capillary forces on the disc increase with surface curvature; thus, they act to restore the disc to its original position. As the disc reenters the light source it again experiences Marangoni propulsion, leading to sustained oscillation for appropriate conditions. Propulsive forces can be modulated with incident light intensity, while the restoring force can be tuned via surface curvature--i.e., drop volume--providing highly tunable oscillatory behaviors. To our knowledge, this is the first example where Marangoni and capillary forces combine to incite sustained motion. As such, a model was developed that describes this behavior and provides key insights into the underlying control parameters. We expect that this simple approach will enable the study of more complex and coupled oscillatory systems. [ABSTRACT FROM AUTHOR]

Understanding the impact of climate stressors on photovoltaic (PV) backsheet degradation in real-use conditions is critical to improve the accelerated testing exposures, extend the backsheet lifetime, and increase the confidence in PV reliability. In this work, a total of 33 PV module backsheets were retrieved from six climatic zones worldwide with 2 - 28 years of exposure. These modules included five types of backsheet air-side materials (or outer layer): poly(vinylidene fluoride) (PVDF), poly(tetrafluoroethylene-co-hexafluoropropylene-co-vinylidene fluoride) (THV), poly(vinyl fluoride) (PVF), poly(ethylene terephthalate) (PET), and polyamide (PA). Attenuated total reflection Fourier-transform infrared spectroscopy (ATR-FTIR) was used to identify air-side materials. The degradation induced color change, gloss loss, and chemical material changes analyzed using optical microscopy, differential scanning calorimetry (DSC), scanning electron microscopy (SEM), colorimetry (yellowness index (YI)), and gloss measurements. PVDF, THV, and PVF air-side layer backsheets, in particular PVF, had minimal degradation in the air-side layer appearance and chemical structures after exposure in different climatic zones. The PET air-side backsheets exhibited obvious color increase (22.55 YI units after about 9 years exposure) and the PA/PA/PA backsheets showed large gloss loss (up to 76.4 %) relative to the unexposed backsheets. Severe cracks between cells that penetrated through the entire thickness of backsheets are observed on PA/PA/PA backsheets after 4-6 years of exposure in 6 climatic zones. The current indoor exposure standards were not sufficient to identify this degradation type. However, fluoropolymer based PV backsheets showed lower levels of degradation predictors and increased climatic resistance. Specific samples (PVF) showed little change from baseline after 28 years of outdoor exposure. • Retrieved module backsheet characterization. • Diverse climatic exposure. • Inhomogeneous backsheet degradation. [ABSTRACT FROM AUTHOR]

We introduce a new approach for colorimetric sensing of ionizing radiation based on photonic polymer multilayer films. Upon immersion in a solvent, the multilayers give rise to reflected structural color in the visible region of the spectrum, with a coloration that depends on the degree of swelling of the low-index layers. Exposure to ionizing radiation leads to either preferential degradation or crosslinking of the low-index polymer, yielding a change in color in the swelled state. We demonstrate the operation of both red- and blue-shifting colorimetric sensors, with sensitivity to electron-beam irradiation in the range of ∼100 kGy, and also show that this approach allows for the preparation of sensors on flexible plastic substrates. [ABSTRACT FROM AUTHOR]

The width tapered beam method for measuring fracture toughness has been contemplated for use in measuring the adhesion of photovoltaic materials, is promoted by it being a viable method for use directly on modules rather than to engineered test specimens. However, precise determination of crack length is often difficult as failure often involves tendril formation, cavitation voids, and other plastic deformation at the crack front in addition to obfuscation by opaque materials. Because fracture energy varies as the square of crack length, imprecise crack tip length results in large measurement uncertainties. In this work, we develop a method to estimate the crack tip length using the relationship between the applied force and the displacement of the load frame. The crack tip is determined for every data point and can be defined from a calibration curve related to the amount of energy put into the beam, or from a theoretically idealized estimation. Once a calibration curve is set up and the equations programmed, the fracture energy as a function of position on the newly formed crack interface can be accurately estimated. The test additionally provides much easier analysis and insight into the joint failure through more precise knowledge of fracture toughness at each de-bonded area. [ABSTRACT FROM AUTHOR]

Photovoltaic backsheets are exposed to harsh outdoor weathering conditions throughout their service lives that can compromise their protective function, through adhesive debonding between their constituent layers and between the backsheet and the module. A large-scale study on adhesive degradation was conducted on 37 field-exposed modules, that spanned 19 different module manufacturers, that were deployed among six Köppen–Geiger climatic zones, and that were fielded between 0 and 28 years. Six outer layer polymer classes were identified among the backsheets: polyamide (PA), polyethylene terephthalate (PET), polyvinyl fluoride (PVF), polyvinylidene fluoride (PVDF), fluoroethylene vinyl ether copolymer (FEVE), and tetrafluoroethylene hexafluoropropylene vinylidene fluoride copolymer (THV). Two adhesion tests were used to measure the adhesive strength: the wedge test and the width-tapered single-cantilever beam (SCB) test. Adhesion energies were compared across exposure time and Köppen–Geiger climatic zone. Many of the PET-, PVF-, and PVDF-based backsheets experienced degradation of the adhesive layer between the backsheet outer and core layers. A consistent trend of decreasing adhesion energy with exposure time was observed in five out of the six backsheet types. Trends among adhesion energy and climatic zone, while expected, were not observed, possibly due to broad ranges in temperature, humidity, and precipitation defining Köppen–Geiger climatic zones. The cantilever beam measurements produced an upper cutoff of approximately 100 J/m2, above which no modules exhibited field delamination. The results are part of a two-part study quantifying adhesion in both field-weathered and indoor-exposed PV backsheets. • Thirty-seven (37) PV modules were retrieved from various regions around the world • Two adhesion tests were used to characterize backsheet adhesion • Adhesion energy decreased with number of years of field exposure • Backsheets with adhesive tie layers often showed failure in an adhesive layer • Modules with adhesion energies greater than 100 J/m2 showed no field delamination [ABSTRACT FROM AUTHOR]

Photovoltaic (PV) backsheets provide critical moisture, mechanical, and electrical insulation to the backside of PV modules, but their continued functionality depends upon their ability to remain well adhered over years of harsh environmental exposure. A study of adhesive strength was conducted on several PV backsheet types exposed to indoor accelerated weathering. Two adhesion tests – the wedge test and single cantilever beam test – were used to measure adhesion energy in four backsheets: two with fluoropolymer-based outer (airside) layers – polyvinyl fluoride (PVF), polyvinylidene fluoride (PVDF) – and two with non-fluoropolymer-based outer layers–polyamide (PA) and polyethylene terephthalate (PET). The effects of changes in temperature, ultraviolet (UV) irradiance, relative humidity, and a periodic water spray were studied. The PET-, PVF- and PVDF-based backsheets all showed instances of debonding in an adhesive layer, which is commonly reported. For the PA-, PET-, and PVDF-based backsheets, adhesion energy dropped fairly rapidly with exposure, reaching very low levels by 4000 h. The PVF-based backsheet was relatively robust to weathering. Pull-off of an outer chalking layer in the PA- and PET-based backsheets suggested a sensitivity to UV. Adhesion in these two backsheets was also highly sensitive to changes in moisture level. Changes in UV irradiance and temperature did not show a statistically significant effect on adhesion loss for the exposure levels used. The present work is part of a two-part adhesion study on both field-weathered and indoor-exposed backsheets, and forms a basis for understanding adhesion degradation across a variety of backsheet types and degradation factors. • Four indoor-exposed backsheet types were adhesion-tested using two different methods. • Adhesion in the PVF-based backsheet was relatively stable. • The PA-, PET- and PVDF-based backsheets exhibited substantial decrease after 4000 hours. • The PA- and PET-based backsheets exhibited sensitivity to changes in moisture level. • The PET-, PVF-, and PVDF-based backsheets all exhibited debonding in an adhesive layer. [ABSTRACT FROM AUTHOR]