Search

Background: Wear of total knee polyethylene has been quantified gravimetrically with thickness measurements and evaluation of surface wear modes. However, these techniques do not localize volumetric wear.Questions/purposes: We used micro-CT scans of retrieved total knee liners and unworn, new liners to determine the volume and location of wear.Methods: We retrieved 12 fixed and 12 rotating-platform bearings after a mean 52 months of use. Inserts were weighed and thickness was measured. Micro-CT scans of retrieved and matched new liners were superimposed to compare the location and magnitude of wear.Results: The average total wear was 254 ± 248 mm(3). The average wear rate was 58 ± 41 mm(3)/year. Wear was 69% of penetration, demonstrating the contribution of deformation to knee wear. Rotating-platform wear rate was 43 ± 25 mm(3)/year and the fixed-bearing rate was 74 ± 49 mm(3)/year. Five percent of the rotating-platform wear rate came from the backside compared with 14% of the fixed-bearing wear rate.Conclusions: Micro-CT can determine the volume and location of wear of retrieved tibial liners. Because the magnitude of the manufacturing tolerances was approximately half the magnitude of the total wear on average, accounting for the potential influence of tolerances is important to accurately measure volumetric wear if the unworn (preimplantation) geometry of the insert is unknown. Without accounting for tolerances, this technique may not be applicable for retrievals with a short followup that have low wear. However, application of micro-CT could be of value in determining the exact location of wear in knee simulator studies in which the same insert is measured repeatedly and manufacturing tolerances are not a concern. [ABSTRACT FROM AUTHOR]

Between October 1982 and December 1984, the senior author performed 223 total hip arthroplasties in 215 patients with use of the anatomic medullary locking hip stem and TriSpike cup. We now report on 119 of these hips at a mean of 22.0 years (range, 20.0 to 25.0 years) after surgery. Of the fifty-six hips with minimum twenty-year follow-up radiographs and the original acetabular component, seventeen (30.4%) had pelvic osteolytic lesions measuring larger than 1.5 cm(2). Of the sixty-eight hips with twenty-year radiographs and the original anatomic medullary locking stem, twenty-five (36.8%) had femoral osteolytic lesions measuring larger than 1.5 cm(2). Acetabular osteolysis was significantly associated with cup loosening (p = 0.006), but the presence of femoral osteolysis was not associated with stem loosening. Kaplan-Meier analysis, with revision for any reason as the end point, revealed that the survival rate at twenty years was 85.8% +/- 5.2% for the acetabular shell and 97.8% +/- 2.2% for the stem. The most common reoperation was polyethylene exchange because of wear or osteolysis. [ABSTRACT FROM AUTHOR]

Periprosthetic osteolysis is a common cause for revision of total hip arthroplasty. When modular cementless acetabular components are stable, curettage and grafting of the osteo-lytic lesion while retaining the component are a good surgical option. Although the midterm outcome of this procedure is known, the quality of the surgical technique is not. We used preoperative and postoperative computed tomography to determine the percentage of periacetabular lesions that was grafted and the percentage of the lesion volume filled with an injectable bone graft substitute. We discovered, even with preoperative computed tomography reconstructions and surgical planning, four of 22 lesions were neglected at the time of surgery. In the 18 lesions that were treated, we were able to fill an average of 49% (range, 0-83%) of the lesion volume. These inconsistent results illustrate a need to further refine surgical techniques and instrumentation to treat one of the most common complications in total hip arthroplasty. Longer followup with repeat computed tomography scans or other imaging techniques would determine if the percentage of lesion fill has an effect on clinical outcome. [ABSTRACT FROM AUTHOR]

Background: Progressive periacetabular osteolysis following total hip arthroplasty may require revision surgery. The purpose of this study was to use computed tomography scans of hemipelves retrieved at autopsy from patients who had had a total hip arthroplasty, to define the radiographic characteristics that differentiate clinically important osteolytic lesions from osteoarthritic bone cysts.Methods: We analyzed forty-four hemipelves that had been retrieved at autopsy at a mean of eight years after a total hip arthroplasty with an uncemented acetabular component. Computed tomography images were analyzed to identify the location, volume, and presence of cortical erosion and/or communication pathways with the joint space for all periacetabular bone defects. Lesions that were not present on preoperative or immediate postoperative plain radiographs were defined as new lesions. These new lesions were compared with those that were present on preoperative or immediate postoperative plain radiographs, which were defined as preexisting lesions.Results: Forty-six lesions were identified on computed tomography, and sixteen of them were preexisting lesions. The mean volume of the preexisting lesions was 1.5 +/- 1.5 cm(3), which was significantly smaller than the mean volume of 5.6 +/- 11.4 cm(3) of the thirty new lesions (p = 0.034). Twenty-eight of the thirty new lesions had a clear communication pathway with the joint space, while thirteen of the sixteen preexisting lesions demonstrated no communication pathway. New lesions were significantly more likely to communicate with the joint space than were preexisting lesions (p < 0.001). Cortical erosion was seen in sixteen of the thirty new lesions; none of the sixteen preexisting lesions exhibited cortical erosion (p < 0.001).Conclusions: The most important difference between osteolytic lesions and preexisting bone defects was the presence of a communication pathway to the joint space. Lesions that did not have an identifiable communication to the joint space were smaller and were not associated with cortical erosion. Lesions with communication to the joint through multiple pathways or through a central dome hole were larger and more likely to be associated with cortical erosion. [ABSTRACT FROM AUTHOR]

Background: Exchange of modular components is a treatment option for the correction of recurrent dislocation of a total hip replacement. In this study, we reviewed our experience with this technique in order to define patient selection criteria and to report the outcome of treatment.Methods: Of 2935 hips treated with primary porous-coated total hip arthroplasty, fourteen (in fourteen patients) that met certain preoperative and intraoperative criteria were treated with modular component exchange because of recurrent hip instability. The primary arthroplasties in these fourteen patients had been performed through a posterior approach. At the revisions, we removed any sources of osseous or soft-tissue impingement that contributed to dislocation. Acceptable stability at the completion of component exchange was defined as stability in maximum flexion, in full extension with external rotation, and in at least 45 degrees of internal rotation with the hip in 90 degrees of flexion and maximum adduction.Results: One patient was lost to follow-up. At a mean of 5.8 years (range, 2.8 to 11.8 years) after the revision, ten of the remaining thirteen patients had not had a dislocation. Of the three patients in whom the hip dislocated after the modular component exchange, only one had recurrent dislocation; thus, recurrent dislocation was eliminated in twelve of thirteen patients.Conclusions: In selected cases, modular component exchange for the treatment of recurrent hip dislocation has a success rate comparable with that of more extensive operations. This method should be considered because it avoids the morbidity associated with revision of well-fixed components. However, to ensure the appropriateness of this surgical option, each patient must be thoroughly evaluated to identify all factors that contribute to instability and adequate intraoperative stability must be achieved. [ABSTRACT FROM AUTHOR]

Introduction: In 2019, a new fixed-bearing implant for unicondylar knee arthroplasty (UKA) was introduced that incorporated a round-on-flat design featuring an Oxinium femoral component coupled with a highly crosslinked polyethylene bearing surface. Compared to prior implants, the design featured smaller size increments coupled with medial and lateral-specific tibial baseplates. The objective of this study is to describe our institution's early experience with this UKA implant system by evaluating survivorship, reasons for revision, and patient-reported outcome measures (PROMs)., Methods: The 944 UKAs that comprise the study population, including 814 medial and 130 lateral joint replacements, were performed by six surgeons from September 2019 through the end of December 2023. All UKA components were cemented, the mean age at surgery was 67.1±10.0 years, 57% (537/944) of the UKAs were performed among women, and the mean body mass index was 30.3±6.2 kg/m 2 . Outcome measures included Kaplan-Meier survivorship using reoperation for any reason as an endpoint, reasons for reoperation, range of motion, and PROMs that were collected preoperatively and postoperatively at 4 weeks, 4 months, 1 year, and 2 years., Results: Using reoperation for any reason as an endpoint, 1-year survivorship was 99.3% (95% CI, 98.7 to 99.9%) and 2-year survivorship was 98.2% (95% CI, 96.9 to 99.5%). There were nine reoperations among the 944 UKAs, including three for infection, two for tibial loosening, one for femoral loosening, one for progression of arthritis, one for patellar instability, and one for recurrent hemarthrosis. The mean time to reoperation was 0.82±0.68 years and all were performed among medial UKAs. Range of motion increased from 117±8 degrees preoperatively to 122±6 degrees at 1-year follow-up. PROMs, including the Knee Injury and Osteoarthritis Outcome Score for Joint Replacement (KOOS JR) and the Patient-Reported Outcomes Measurement Information System (PROMIS) Global Health Physical score, demonstrated progressive increases from the preoperative assessment through 2-year follow-up. For UKAs with preoperative and 2-year KOOS JR scores, the mean change was 31±17., Conclusion: As new implants and technologies are introduced, documenting the early outcome from high volume centers can offer valuable insights to validate the effectiveness of implant systems before they are adopted by the broader orthopedic community. This study demonstrates encouraging early outcome data associated with a contemporary UKA system based on survivorship and PROMs. At this early stage, there are no implant-related concerns but obtaining additional follow-up will be important to quantify how revisions and PROMs evolve over time., Competing Interests: Human subjects: Consent for treatment and open access publication was obtained or waived by all participants in this study. The Inova Health System Institutional Review Board issued approval NA. An Inova Health System Institutional Review Board Chair/Designee reviewed the submission and determined that it met the requirements for exemption. Additionally, a waiver of HIPAA was reviewed and approved. Animal subjects: All authors have confirmed that this study did not involve animal subjects or tissue. Conflicts of interest: In compliance with the ICMJE uniform disclosure form, all authors declare the following: Payment/services info: The Anderson Orthopaedic Research Institute received funding from Smith & Nephew to support this study. Financial relationships: Kevin B. Fricka declare(s) stock/stock options from Vent Creativity. Kevin B. Fricka declare(s) stock/stock options from OrthoAlign. Robert H. Hopper, Jr. declare(s) a grant from Zimmer Biomet. The Anderson Orthopaedic Research Institute has received funding to conduct an Investigational Device Exemption study related to the Oxford unicondylar knee implant. Craig J. McAsey declare(s) personal fees from Merit Medical. Kevin B. Fricka declare(s) personal fees and royalties from Smith & Nephew. Dr. Fricka is a member of Smith & Nephew's unicompartmental knee system design team, receives consulting fees for serving on a Knee Advisory Board, and receives payments for lectures and presentations. Kevin B. Fricka declare(s) non-financial support from Operation Walk Virginia. He serves as a board member for Operation Walk Virginia. Kevin B. Fricka declare(s) non-financial support from Anderson Orthopaedic Research Institute. He serves as a board member for the Anderson Orthopaedic Research Institute. Kevin B. Fricka declare(s) a business ownership interest from Enhanced Medical Nutrition. Other relationships: All authors have declared that there are no other relationships or activities that could appear to have influenced the submitted work., (Copyright © 2024, Fricka et al.)

Aims: The optimal bearing surface design for medial unicompartmental knee arthroplasty (UKA) remains controversial. The aim of this study was to compare outcomes of fixed-bearing (FB) and mobile-bearing (MB) UKAs from a single high-volume institution., Methods: Prospectively collected data were reviewed for all primary cemented medial UKAs performed by seven surgeons from January 2006 to December 2022. A total of 2,999 UKAs were identified, including 2,315 FB and 684 MB cases. The primary outcome measure was implant survival. Secondary outcomes included 90-day and cumulative complications, reoperations, component revisions, conversion arthroplasties, range of motion, and patient-reported outcome measures. Overall mean age at surgery was 65.7 years (32.9 to 94.3), 53.1% (1,593/2,999) of UKAs were implanted in female patients, and demographics between groups were similar (p > 0.05). The mean follow-up for all UKAs was 3.7 years (0.0 to 15.6)., Results: Using revision for any reason as an endpoint, five-year survival for FB UKAs was 97.2% (95% CI 96.4 to 98.1) compared to 96.0% for MB (95% CI 94.1 to 97.9; p = 0.008). The FB group experienced fewer component revisions (14/2,315, 0.6% vs 12/684, 1.8%; p < 0.001) and conversion arthroplasties (38/2315, 1.6% vs 24/684, 3.5%; p < 0.001). A greater number of MB UKAs underwent revision due to osteoarthritis progression (FB = 21/2,315, 0.9% vs MB = 16/684, 2.3%; p = 0.003). In the MB group, 12 (1.8%) subjects experienced bearing dislocations which required revision surgery. There were 15 early periprosthetic tibia fractures (0.6%) in the FB group compared to 0 for MB (p = 0.035)., Conclusion: In similar patient populations, FB UKAs demonstrated slightly higher survival than a commonly used MB design. Adverse event profiles differed by bearing type, with an increased risk of bearing dislocation and OA progression with MB designs, and early periprosthetic tibia fractures for FB designs., Competing Interests: K. B. Fricka reports IP Royalties, payment as a presenter and speaker, and research support from Smith & Nephew, as well as consulting fees and research support from Zimmer Biomet, all unrelated to this study. W. G. Hamilton reports research support from Zimmer Biomet, not related to this study. R. A. Sershon reports consulting fees from Zimmer Biomet, not related to this study., (© 2024 The British Editorial Society of Bone & Joint Surgery.)

Background: Advances in total hip arthroplasty (THA) have resulted in evolving revision indications and intraoperative techniques, which can influence the exposure of trainees to complex cases. We report 3 decades of revision experience from a tertiary referral center that trains fellows, comparing the reasons for revision and the complexity of revisions over time., Methods: We retrospectively reviewed all revision THAs performed at our institution from 1990 to 2022. Revision diagnoses, components revised, types of revision implants used, and exposure techniques were collected. A "complex" revision was defined as a case that involved an extended trochanteric osteotomy, triflange and cup-cage construct, or acetabular augment., Results: A total of 3,556 THA revisions were identified (108 revisions/year). Aseptic loosening was the most common indication in 1990 to 1999 (45 per year), but decreased to 28.3/year in 2010 to 2019. From 1990 to 1999 and 2010 to 2019, fracture increased from 3.1 to 7.3 per year, infection from 2.9/year to 16.9/year, and metallosis from 0.1 to 13.2 per year. Both component revision were common from 1990 to 1994 (42.6 per year), while polyethylene exchange was most common in 2010 to 2019 (43.3 per year). A decrease was observed in "complex" cases over time: 14.8 extended trochanteric osteotomies/year in 2000 to 2004 compared to 5.4 per year in 2018 to 2022, 4.5 triflange and cup-cage constructs/year in 2004 to 2007 compared to 0.8 per year in 2018 to 2022, and 4 acetabular augments per year in 2009 to 2012 compared to 1 per year in 2018 to 2022., Conclusions: Indications for revision have changed over the decades, while the number of "complex" revisions has gradually decreased, presumably due to advances in implants and materials. If this trend extends to other training institutions, the next generation of arthroplasty surgeons will have less exposure to complex revisions during their training., (Copyright © 2024 Elsevier Inc. All rights reserved.)

Aims: The first aim of this study was to evaluate whether preoperative renal function is associated with postoperative changes in whole blood levels of metal ions in patients who have undergone a Birmingham Hip Resurfacing (BHR) arthroplasty with a metal-on-metal bearing. The second aim was to evaluate whether exposure to increased cobalt (Co) and chromium (Cr) levels for ten years adversely affected renal function., Methods: As part of a multicentre, prospective post-approval study, whole blood samples were sent to a single specialized laboratory to determine Co and Cr levels, and the estimated glomerular filtration rate (eGFR). The study included patients with 117 unrevised unilateral BHRs. There were 36 females (31%). The mean age of the patients at the time of surgery of 51.3 years (SD 6.5), and they all had preoperative one-, four-, five-, and ten-year laboratory data. The mean follow-up was 10.1 years (SD 0.2)., Results: Median Co levels at one year postoperatively increased significantly compared with the preoperative values, by a factor of 9.7, from 0.13 to 1.26 ppb (p < 0.001), and the median Cr levels increased significantly by a factor of 2.5, from 0.60 to 1.50 ppb (p < 0.001). Lower preoperative eGFRs were associated with significantly larger increases in Co at one year compared with the preoperative levels (ρ = -0.26; p = 0.005), but there was no relationship between preoperative eGFRs and changes in Cr at one year (ρ = -0.13; p = 0.153). Metal levels remained relatively constant with the passage of time, with a median ten-year value of 1.12 ppb for Co and 1.29 ppb for Cr. There was no significant relationship between the Co and Cr levels at ten-year follow-up and the change in eGFR from the preoperative level to that at ten years (ρ = -0.02; p = 0.827 for Co; ρ = -0.008; p = 0.933 for Cr)., Conclusion: Although patients with lower preoperative eGFRs tended to have larger increases in Co levels at one year, increased metal levels for patients who underwent unilateral BHR did not adversely affect renal function during the first ten postoperative years., Competing Interests: All authors report funding from Smith & Nephew to the Anderson Orthopaedic Research Institute to conduct the post-approval study that generated the data used for this analysis, however no financial support was provided for the development of this manuscript., (© 2024 The British Editorial Society of Bone & Joint Surgery.)

Background: Infection following total knee arthroplasty (TKA) remains a challenging clinical problem. Using American Joint Replacement Registry data, this study examined factors related to the incidence and timing of infection., Methods: Primary TKAs performed from January 2012 through December 2018 among patients ≥65 years of age at surgery were queried from the American Joint Replacement Registry and merged with Medicare data to enhance capture of revisions for infection. Multivariate Cox regressions incorporating patient, surgical, and institutional factors were used to produce hazard ratios (HRs) associated with revision for infection and mortality after revision for infection., Results: Among 525,887 TKAs, 2,821 (0.54%) were revised for infection. Men had an increased risk of revision for infection at all-time intervals (≤90 days, HR = 2.06, 95% CI: 1.75-2.43, P < .0001; >90 days to 1 year, HR = 1.90, 95% CI: 1.58-2.28, P < .0001; >1 year, HR = 1.57, 95% CI: 1.37-1.79, P < .0001). TKAs performed for osteoarthritis had an increased risk of revision for infection at ≤90 days (HR = 2.01, 95% CI: 1.45-2.78, P < .0001) but not at later times. Mortality was more likely among patients who had a Charlson Comorbidity Index (CCI) ≥ 5 compared to those who had a CCI ≤ 2 (HR = 3.21, 95% CI: 1.35-7.63, P = .008). Mortality was also more likely among older patients (HR = 1.61 for each decade, 95% CI: 1.04-2.49, P = .03)., Conclusion: Based on primary TKAs performed in the United States, men were found to have a persistently higher risk of revision for infection, while a diagnosis of osteoarthritis was associated with a significantly higher risk only during the first 90 days after surgery., (Copyright © 2023 Elsevier Inc. All rights reserved.)

Background: Mobile bearing designs are intended to reduce wear, but mixed results were reported from retrieval analyses. Postmortem evaluation (PM) provides the opportunity to assess polyethylene damage in successful implants. We compared damage patterns, MRI presentation, and histology between mobile-bearing and fixed tibial inserts retrieved postmortem and compared these results to our prior findings from implants retrieved at revision., Methods: Eleven postmortem knees with rotating platform (RP) implants and 13 with fixed bearing (FB) implants were examined. All were MRI scanned, and tissue samples were collected from standardized regions for histology. Polyethylene inserts were subjectively scored to assess articular, backside, and PS post surfaces for damage modes and severity., Results: Average duration of implantation was 9.3 years (1.7-19.6 years). Surface burnishing was the most common polyethylene damage mode. Average damage scores were higher for RP (53.4) compared to FB inserts (34.4) due to greater backside damage (13.4 for RP vs 1.4 for FB). A minimal difference in damage was observed on the articular surfaces (37.4 RP vs 30.0 FB). Mild innate macrophage reactions were seen in 8 (72.7%) RP and 5 (45.5%) FB specimens. Polyethylene particles were identified in 7 (63.6%) RP and 3 (27.7%) FB specimens., Conclusions: Postmortem inserts showed low damage levels and mild tissue reactions compared to those reported for implants removed at revision arthroplasty. Nonetheless, trends in comparing RP and FB inserts were consistent with those seen in retrieval analyses, demonstrating the usefulness of retrieval studies in capturing performance differences among TKA designs., (Copyright © 2022 Elsevier Inc. All rights reserved.)

Crosslinking substantially reduces the wear of ultra-high molecular weight polyethylene (UHMWPE) used in total hip arthroplasty (THA) but some reports have indicated that first generation liners manufactured without antioxidants may be vulnerable to in vivo oxidation. This study evaluated maximum oxidation using Fourier transform infrared spectroscopy per ASTM F2102-06 ε1 and linear head penetration using a coordinate measuring machine among 66 revision-retrieved THA components with in vivo durations ranging from 0.02 to 24.6 years. These included 30 liners crosslinked with 5 Mrad of gamma radiation and then melted, 13 non-crosslinked, never-irradiated liners sterilized with gas plasma and 23 non-crosslinked, never-irradiated liners sterilized with ethylene oxide. All liners were vacuum-sealed and stored at -20°C prior to analysis with the exception of three retrievals of each material type that were stored in air for 9.9 to 21.5 years. All 57 vacuum-sealed and frozen retrievals demonstrated good oxidative stability with maximum oxidation indices (OIs) less than 1.0 and 75% (43/57) of these liners had maximum OIs less than 0.1. Linear penetration measurements were lower in the crosslinked liners compared to non-crosslinked retrievals. Although instances of oxidation and embrittlement were found after ex vivo storage in air among liners that did not have free radicals at the time of implantation, in vivo oxidation does not appear to be a clinical concern through the first decade of service for crosslinked liners and at up to 25 years after surgery for non-crosslinked liners., (© 2021 Wiley Periodicals LLC.)

Background: One purported benefit of the direct anterior approach (DAA) for total hip arthroplasty (THA) is a lower rate of postoperative dislocation., Methods: An institutional database was used to identify 8840 primary THAs performed from 2003 to 2020 including 5065 (57%) performed using the DAA and 3775 (43%) performed via the posterior approach (PA). Direction and mechanism of dislocation were determined from chart review. Outcomes were compared using Kaplan-Meier survivorship with dislocation as the endpoint and a Cox multivariate regression was used to investigate factors associated with dislocation. The mean follow-up was 1.7 ± 2.0 years for the DAA and 3.1 ± 3.3 years for the PA., Results: The 0.5% (26/5065) incidence of dislocation among DAA hips was significantly less than the 3.3% (126/3775) among PA cases (P < .001). The majority of dislocations were posterior (DAA 57%, PA 79%) and occurred during activities of daily living (DAA 82%, PA 77%). Five-year survivorship was significantly higher for the DAA group compared to the PA group (99.1% vs 95.4%, P < .001). Dislocation risk was 4.9 times higher for the PA compared to the DAA (hazard ratio = 4.9, 95% confidence interval = 3.2-7.5, P < .001). Increasing head diameter reduced the risk (hazard ratio = 0.70, 95% confidence interval = 0.57-0.86, P < .001). The 0.2% incidence (10/5065) of revision for instability among the DAA group was significantly lower than the 1.1% (43/3775) rate for the PA group (P < .001)., Conclusion: Compared to primary THAs performed with the PA, DAA cases had a lower risk of dislocation, higher survivorship with dislocation as an endpoint, and a lower risk of revision for instability in this single institution cohort., (Copyright © 2021 Elsevier Inc. All rights reserved.)

Background: Revision total hip arthroplasty with modular component exchange can limit morbidity by retaining well-fixed components but dislocation has been a relatively frequent postoperative complication. This study evaluated the effect of surgical approach on dislocation rate in a modern revision cohort., Methods: From 2010 to 2020, 248 aseptic head and liner exchanges were performed at a single institution. The mean patient age at revision was 64.9 ± 10.4 years and 50% (123/248) were performed among males. Indications for revision included 140 (56%) for polyethylene wear, 68 (27%) for failed metal-on-metal components, and 40 (16%) for instability. The mean follow-up after revision was 2.3 years., Results: Thirty (12%) hips dislocated at a mean of 0.6 years (range 0.01-4.6) postoperatively. The dislocation rate by revision approach was 17% (9/54) for the direct anterior, 6% (5/80) for the direct lateral, and 14% (16/114) for the posterolateral approach (P = .13). Hips revised by the direct anterior approach that dislocated were more abducted (51 ± 8 vs 45 ± 8, P = .05) and more anteverted (26 ± 9 vs 20 ± 7, P = .04) than non-dislocators. Among all 248 hips, cups with more than 48° of abduction were 2.6 times more likely to dislocate (P = .01). Head diameter, neck length, patient age, and gender were not associated with dislocation (P ≥ .20)., Conclusion: Dislocation remains a common complication after head and liner exchange regardless of approach. Cup position is associated with postoperative instability and must be critically evaluated during preoperative planning., (Copyright © 2021 Elsevier Inc. All rights reserved.)

Corrosion and wear are commonly found at the taper-trunnion connection of modular total hip arthroplasty (THA) explanted devices. While metal/metal (M/M) modular taper-trunnion connections exhibit more wear/corrosion than ceramic/metal (C/M) modular taper-trunnion connections, damage is present in both, regardless of material. This study used a combination of assessment techniques including clinical data, visual scoring assessment, optical imaging, profilometry, and x-ray photoelectron microscopy (XPS), to investigate wear mechanisms and damage features at the modular taper-trunnion connection of 10 M/M and 8 C/M explanted THAs. No correlation was found between any demographic variable and corrosion wear and assessment scores. All assessment techniques demonstrated that the stem trunnions had more damage than head tapers for both explant groups and agreed that C/M explants had less corrosion and wear compared to M/M explants. However, visual assessment scores differed between assessment techniques when evaluating the tapers and trunnions within the two groups. Profilometry showed an increase (p <.05) in surface roughness for stem trunnions compared to head tapers for both explant groups. X-ray photoelectron spectroscopy performed on deposits from two M/M explants found chromium and molybdenum carbides beneath the surface while chromium sulfate and aged bone mineral were found on the surface suggesting that the debris is a result of corrosion rather than wear. These results indicate that taper-trunnion damage is more prevalent for M/M explants, but C/M explants are still susceptible to damage. More comprehensive analysis of damage is necessary to better understand the origins of taper-trunnion damage., (© 2021 The Authors. Journal of Biomedical Materials Research Part B: Applied Biomaterials published by Wiley Periodicals LLC. This article is a U.S. Government work and is in the public domain in the USA.)

Background: To assess how implant alignment affects unicompartmental knee arthroplasty (UKA) outcome, we compared tibial component alignment of well-functioning UKAs against 2 groups of failed UKAs, revised for progression of lateral compartment arthritis ("Progression") and aseptic loosening ("Loosening")., Methods: We identified 37 revisions for Progression and 61 revisions for Loosening from our prospective institutional database of 3351 medial fixed-bearing UKAs performed since 2000. Revision cohorts were matched on age, gender, body mass index, and postoperative range of motion with "Successful" unrevised UKAs with minimum 10-year follow-up and Knee Society Score ≥70. Tibial component coronal (TCA) and sagittal (TSA) plane alignment was measured on postoperative radiographs. Limb alignment was quantified by hip-knee-ankle (HKA) angle on long-leg radiographs. In addition to directly comparing groups, a multivariate logistic regression examined how limb and component alignments were associated with UKA revision., Results: In the Progression group, component alignment was similar to the matched successes (TCA 3.6° ± 3.5° varus vs 5.1° ± 3.5° varus, P = .07; TSA 8.4° ± 4.4° vs 8.8° ± 3.6°, P = .67), whereas HKA angle was significantly more valgus (0.3° ± 3.6° valgus vs 4.4° ± 2.6° varus, P < .001). Loosening group component alignment was also similar to the matched successes (TCA 6.1° ± 3.7° varus vs 5.9° ± 3.1° varus, P = .72; TSA 8.4° ± 4.6° vs 8.1° ± 3.9°, P = .68), and HKA was significantly more varus (6.1° ± 3.1° varus vs 4.0° ± 2.7° varus, P < .001). Using a multivariate logistic regression, HKA angle was the most significant factor associated with revision (P < .001)., Conclusion: In this population of revised UKAs and long-term successes, limb alignment was a more important determinant of outcome than tibial component alignment., Level of Evidence: Level III case-control study., (Copyright © 2021 Elsevier Inc. All rights reserved.)

Purpose: Accurate component placement and restoration of patient anatomy are critical in total hip arthroplasty (THA) surgery. Although intraoperative radiographs are sometimes utilized, it is unclear whether this practice can improve accuracy., Materials and Methods: This study evaluated acetabular cup abduction, anteversion, leg length, and offset among 100 posterior approach THAs performed without imaging (No X-ray group) and compared them to a subsequent series of 100 THAs where an intraoperative radiograph was taken with the trial components in place (X-ray group). THAs were performed using a posterior approach by a single, experienced surgeon whose goal was to place the cup at 45° of abduction and 30° of anteversion. Supine anteroposterior pelvic digital radiographs taken at the first (nominal 4-week) postoperative visit were used for measurements., Results: Slight differences in cup abduction (47°±6° vs 44°±6°, respectively, P =0.003) and anteversion angle (35°±6° vs 31°±6°, respectively, P <0.001) were observed between the X-ray and No X-ray groups; however, a similar proportion of cups within 10° of the target angles was observed (76% vs 83%, respectively, P =0.22). No difference in offset measurements (1.1±6.6 mm vs 0.3±6.9 mm, respectively, P =0.42) or leg lengths (0.3±3.8 mm vs 0.3±4.8 mm, respectively, P =0.94) was observed between the X-ray and No X-ray groups; however, the X-ray group showed less leg length variation ( P =0.05)., Conclusion: In this study, the routine use of intraoperative radiographs was not associated with improved implant positioning for uncomplicated primary THA., Competing Interests: CONFLICT OF INTEREST: The authors declare that there is no potential conflict of interest relevant to this article. The Inova Health System provided financial support that was used to undertake this research but did not restrict or define the scope of this study., (Copyright © 2021 by Korean Hip Society.)

Background: The BIRMINGHAM HIP Resurfacing (BHR) system is a metal-on-metal hip implant system approved by the U.S. Food and Drug Administration in 2006. The approval required a multicenter, prospective, post-market-approval study. Our purpose is to report the current results at 10 years of follow-up., Methods: Between October 2006 and December 2009, 280 primary BHR procedures were performed at 5 sites. Outcome measures included Kaplan-Meier survivorship, reasons for revision, radiographic component stability and osteolysis, Harris hip scores, and metal levels including cobalt and chromium. The mean age at the time of the procedure was 51.3 ± 7.1 years, 74% (206) of 280 BHRs were implanted in male patients, the mean body mass index was 27.8 ± 4.4 kg/m2, and 95% (265) of 280 hips had a primary diagnosis of osteoarthritis. The mean follow-up among all 280 hips was 9.0 ± 2.5 years. Prior to 10-year follow-up, 20 hips were revised and 5 patients representing 5 hips had died. Among the remaining 255 hips, 218 (85%) met the minimum follow-up of 10 years., Results: The 10-year survival free from all-cause component revision was 92.9% (95% confidence interval [CI], 89.8% to 96.1%) for all hips and 96.0% (95% CI, 93.1% to 98.9%) among male patients <65 years old at the time of the procedure. Reasons for revision included femoral loosening (n = 5), femoral neck fracture (n = 3), pseudotumor (n = 3), osteolysis (n = 2), and acetabular loosening (n = 1), as well as 6 revisions for a combination of pain, noise, or metal levels. Among unrevised hips, the median Harris hip score improved from preoperatively (59) to 1 year postoperatively (99; p < 0.001) and remained stable through 10 years postoperatively (99; p = 0.08). Radiographically, 5% (10) of 218 unrevised hips had osteolysis with no component migration. Median metal levels had increased at 1 year postoperatively (cobalt: from 0.12 ppb preoperatively to 1.5 ppb at 1 year postoperatively, p < 0.001; chromium: from 0.6 ppb preoperatively to 1.7 ppb at 1 year postoperatively, p < 0.001), then remained stable through 5 years before slightly decreasing at 10 years postoperatively (cobalt: 1.3 ppb, p < 0.001; chromium: 1.4 ppb, p < 0.001)., Conclusions: This prospective, multicenter, post-market-approval study demonstrated that the BHR implant system is safe and effective through 10 years of follow-up, particularly among young male patients., Level of Evidence: Therapeutic Level IV. See Instructions for Authors for a complete description of levels of evidence., Competing Interests: Disclosure: Smith & Nephew, the manufacturer of the implant, provided funding for each site to support this post-approval study. No funding was allocated for the preparation of this manuscript. One author (V.B.) was an employee of Smith & Nephew when the study was conducted. The Disclosure of Potential Conflicts of Interest forms are provided with the online version of the article (http://links.lww.com/JBJS/G497)., (Copyright © 2021 by The Journal of Bone and Joint Surgery, Incorporated.)

Aims: The purpose of this study is to examine six types of bearing surfaces implanted at a single institution over three decades to determine whether the reasons for revision vary among the groups and how long it takes to identify differences in survival., Methods: We considered six cohorts that included a total of 1,707 primary hips done between 1982 and 2010. These included 223 conventional polyethylene sterilized with γ irradiation in air (CPE-GA), 114 conventional polyethylene sterilized with gas plasma (CPE-GP), 116 crosslinked polyethylene (XLPE), 1,083 metal-on-metal (MOM), 90 ceramic-on-ceramic (COC), and 81 surface arthroplasties (SAs). With the exception of the COC, all other groups used cobalt-chromium (CoCr) femoral heads. The mean follow-up was 10 (0.008 to 35) years. Descriptive statistics with revisions per 100 component years (re/100 yr) and survival analysis with revision for any reason as the endpoint were used to compare bearing surfaces., Results: XLPE liners demonstrated a lower cumulative incidence of revision at 15 years compared to the CPE-GA and CPE-GP groups owing to the absence of wear-related revisions (4% for XLPE vs 18%, p = 0.02, and 15%, p = 0.003, respectively). Revisions for adverse local tissue reactions occurred exclusively among the MOM (0.8 re/100 year) and SA groups (0.1 re/100 year). The revision rate for instability was lower among hips with 36 mm and larger head sizes compared to smaller head sizes (0.2% vs 2%, p < 0.001)., Conclusion: The introduction of XLPE has eliminated wear-related revisions through 15-year follow-up compared to CPE-GP and CPE-GA. Dislocation incidence has been reduced with the introduction of larger diameter heads but remains a persistent concern. The potential for adverse local tissue reactions with MOM requires continued follow-up. Cite this article: Bone Joint J 2020;102-B(7 Supple B):105-111.

Background: The hypothetical association between health-care errors and the transition of the medical academic year has been termed the "July effect." Data supporting its existence are conflicting, particularly in orthopedic surgery, and prior studies have inappropriately grouped fellows with resident trainees. No studies to date have examined whether a training initiation effect exists among surgical fellows in adult reconstructive orthopedics., Methods: This is a level IV retrospective cohort study reviewing 15,650 primary hip and knee arthroplasties performed from 2006 to 2016 at a single institution. Forty arthroplasty fellows were trained during this 10-year period. Primary outcome measures included intraoperative complications, additional procedures, revisions, and nonoperative complications within 90 days of surgery. These complication rates were analyzed by quarter of academic year and by temporal progression through three-month fellowship rotations., Results: There were no differences in intraoperative complication, revision, or nonoperative complication rates between any academic quarter. There was a single statistically lower rate of additional procedures in the third quarter (1.2%) than in the fourth quarter (1.8%, P = .04). The most common complication in this subset was wound dehiscence for patients undergoing hip arthroplasty and stiffness for patients undergoing knee arthroplasty. There was no difference in complication rates during the first, second, or third month as fellows progressed through a single rotation., Conclusion: This study does not support the existence of a training-initiation effect among fellows in adult hip and knee reconstruction. Graduated autonomy can be safely employed in a fellowship program without negatively impacting patient outcomes, ensuring the continued high-caliber training of future surgeons., (Copyright © 2020 Elsevier Inc. All rights reserved.)

Background: To better define the optimal alignment target for medial fixed-bearing unicompartmental knee arthroplasty (UKA), this study compares the postoperative mechanical alignment of well-functioning UKAs against 2 groups of failed UKAs, including revisions for progression of lateral compartment osteoarthritis ("Progression") and revisions for aseptic loosening or subsidence ("Loosening")., Methods: From our prospective institutional database of 3351 medial fixed-bearing UKAs performed since 2000, we identified 37 UKAs revised for Progression and 61 UKAs revised for Loosening. Each of these revision cohorts was matched based on age at surgery, gender, body mass index, and postoperative range of motion with unrevised UKAs that had at least 10 years of follow-up and a Knee Society Score of 70 or greater without subtracting points for alignment ("Success" groups). Postoperative alignment was quantified by the hip-knee-ankle (HKA) angle measured on long-leg alignment radiographs., Results: The mean HKA angle at 4-month follow-up for the Progression group was 0.3° ± 3.6° of valgus compared to 4.4° ± 2.6° of varus for the matched Success group (P < 0.001). For the Loosening group, the mean HKA angle was 6.1° ± 3.1° of varus versus 4.0° ± 2.7° of varus for the matched Success group (P < 0.001)., Conclusions: Patients with well-functioning UKAs at 10 years exhibited mild varus mechanical alignment of approximately 4°, whereas patients revised for progression of osteoarthritis averaged more valgus and those revised for loosening or subsidence averaged more varus. The optimal mechanical alignment for medial fixed-bearing UKA survival with contemporary polyethylene is likely slight varus., (Copyright © 2019 Elsevier Inc. All rights reserved.)

Background: The Bundled Payments for Care Improvement (BPCI) initiative was introduced in 2013 to reduce Medicare healthcare costs while preserving or enhancing quality. We examined data from a metropolitan healthcare system comprised of 1 higher volume hospital and 4 lower volume hospitals that voluntarily elected to participate in the BPCI Major Joint Replacement of the Lower Extremity Model 2, beginning July 1, 2015. Stratifying the data by hospital volume, we determined how costs changed during the 16-month period when all 5 hospitals participated compared to the 1-year period preceding BPCI participation, where savings were achieved, and how the hospitals were rewarded., Methods: The Medicare data included the 90-day target for each episode and actual part A and part B spending for the anchor hospitalization plus all post-acute payments including inpatient rehabilitation, skilled nursing, home health, outpatient physical therapy, and hospital readmissions., Results: The mean episode of care cost decreased by 11.1% (from $21,324 to $18,953) at the higher volume hospitals and by 8.3% (from $25,724 to $23,584) at the lower volume hospitals during BPCI participation compared to the preceding year. The savings were achieved by reducing the use of inpatient rehabilitation, shortening the length of stay at skilled nursing facilities, and decreasing readmission rates. Although the higher volume hospital achieved an increased mean savings of $230 per episode compared to the lower volume hospitals ($2371 vs $2141), it was penalized $490 per episode after reconciling the actual Medicare expenditures with the BPCI targets while the lower volume hospitals received a mean reward of $315 per episode., Conclusion: The BPCI initiative decreased costs and readmissions within our healthcare system. Despite substantial savings compared to the preceding year, the higher volume hospital's low target derived from its 2009-2012 baseline costs was not achieved which resulted in a penalty and led it to withdraw from the BPCI initiative in October 2016., (Copyright © 2019 Elsevier Inc. All rights reserved.)

Background: Our understanding of fretting and corrosion at head-neck junctions in modular THAs in vivo is based largely on the analysis of retrieved implants removed for various diagnoses. Little is known about the condition of head-neck tapers in well-functioning THAs., Questions/purposes: Regarding a cohort of well-functioning autopsy-retrieved modular THAs, we asked: (1) Does trunnion geometry or femoral head material affect the pull-off force of the femoral head? (2) Is there a relationship between trunnion damage and length of implantation time, head diameter, and neck length? (3) Does visual damage scoring accurately determine the presence or absence of corrosion on cobalt-chrome trunnions?, Methods: Sixty-six femoral stems and engaged femoral heads were retrieved at autopsy from 53 patients at Anderson Orthopaedic Research Institute from 1998 to 2014. Ten stems were excluded for low stem design group size or insufficient head-stem clearance for pull-off testing, leaving a cohort of 56 THAs with a median implantation time of 10 years (range, 1-24 years). The femoral stems included three cobalt-chrome (CoCr) designs from a single manufacturer with either a 12/14 or 14/16 trunnion design (N = 36 and 20, respectively) mated with alumina or CoCr heads (N = 13 and 43, respectively). The force required to pull off the femoral heads was measured using a uniaxial load frame according to ASTM F2009-00. Mating surfaces were visually examined to assess the presence and severity of fretting and corrosion using a modified Goldberg scoring system. Three 12/14 trunnions of similar implantation lengths and varied damage scores were selected for imaging with a scanning electron microscope (SEM) and energy dispersive x-ray analysis (EDAX) to confirm the absence or presence of corrosion damage., Results: No difference was seen in pull-off force between groups based on trunnion geometry and head material (median [range], alumina-12/14: 3127 [2320-6992] N, alumina-14/16: 2670 [1095-7919] N, CoCr-12/14: 2255 [1332-5939] N, CoCr-14/16: 2812 [1655-4246] N; p = 0.132). A positive correlation was found between damage score and length of implantation (ρ = 0.543, p < 0.001). However, no correlation between damage score and either head diameter or neck length was found (ρ = -0.012, p = 0.930 and ρ < 0.001, p = 0.995, respectively). In all, 39 of 56 specimens demonstrated no fretting or corrosion, and 16 specimens had mild damage scores. One specimen demonstrated severe corrosion without visual evidence of fretting. The presence of intergranular corrosion on this trunnion was determined by SEM imaging and EDAX. The absence of corrosion products on two trunnions with no observed damage was confirmed., Conclusions: This study found little evidence of fretting and corrosion in a cohort of well-functioning CoCr-CoCr and alumina-CoCr head-neck couples. Further studies are necessary to characterize fretting and corrosion at head-neck junctions of well-functioning implants of other designs and manufacturers., Clinical Relevance: The results from this study suggest that patients with well-functioning THAs using polyethylene bearing surfaces with alumina or CoCr heads appear to be at low risk for trunnion corrosion for the specific CoCr alloy stems and trunnion geometries analyzed here.

Background: Scrutiny from the federal government and the media regarding the safety of 1 surgeon doing cases in 2 operating rooms (ORs) on the same day, prompted us to examine our own institutional data. Over the past 11 years, surgeons at our facility have operated consecutively in 1 OR on a given day or used 2 alternating ORs. This study compares these cases with a focus on revisions and complications in both groups., Methods: Six surgeons performed a total of 16,916 primary hip and knee arthroplasties from 2006-2016. 7002 cases (41%) were consecutive cases (CCs) and 9914 cases (59%) were overlapping cases (OCs). Intraoperative complications, component revisions, and postoperative complications within 90 days of surgery were compared between the CC and OC groups., Results: There was no difference in intraoperative complication rates between the two groups (CC 1.6% vs. OC 1.7%, relative risk 1.082, 95% confidence interval 0.852 to 1.375, P = .52). There was no difference in 90-day component revision rates among the CC and OC groups (0.66% vs. 0.85% respectively, relative risk = 1.290, 95% confidence interval 0.901 to 1.845, P = .19). There was also no difference in 90-day complication rates among the CC and OC groups (1.33% vs. 1.45% respectively, relative risk = 1.094, 95% confidence interval 0.844 to 1.417, P = .54)., Conclusion: This large study of a single institution with multiple surgeons over an 11-year period shows no compromise in patient safety or outcomes when comparing cases done in either consecutive or overlapping rooms., (Copyright © 2018 Elsevier Inc. All rights reserved.)

Background: Crosslinked polyethylene (XLPE) liners used for primary THA have demonstrated lower wear rates than noncrosslinked, conventional polyethylene (CPE) liners through the first decade of clinical service. However, little high-quality evidence is currently available regarding the second decade performance of these implants and it remains uncertain whether the onset of osteolysis has simply been delayed or if the wear associated with XLPE liners will remain low enough that osteolysis will not occur. It is also unknown how the potential reductions in wear and osteolysis will influence long-term revision rates., Questions/purposes: Do patients who underwent THA with XLPE liners demonstrate (1) a lower rate of revision for wear-related complications; (2) a reduced wear rate; and (3) a lower frequency of osteolysis compared with those with CPE liners?, Methods: Over an 18-month period from 1999 to 2000, 226 patients who had 236 primary THAs consented to participate in a randomized controlled trial conducted at one institution. To be eligible for intraoperative randomization, patients had to be implanted with a 28-mm cobalt-chrome alloy femoral head, a 4-mm lateralized liner, and the same cup and stem design. Six patients with six THAs were excluded intraoperatively because they did not receive study components for reasons unrelated to the liner material. The remaining 230 THAs among 220 patients were randomized to XLPE liners or CPE liners. The mean age at surgery was 62 ± 11 years and there were no differences in age, gender, or body mass index among the groups. There was no differential loss to followup between the study groups; among patients not known to be deceased or having undergone revision, minimum 14-year radiographic followup is available for 85 THAs including 46 with XLPE and 39 with CPE liners. Polyethylene wear was measured radiographically using Martell's Hip Analysis Suite and areas of osteolysis were evaluated before revision or at most recent followup. Revision rates at 15 years using reoperation for any reason and revision for wear or osteolysis were calculated using cumulative incidence considering patient death as a competing risk., Results: The cumulative incidence of revision at 15 years using reoperation for wear-related complications as an endpoint was lower in the XLPE group than the CPE group (0%, 95% confidence interval [CI], 0%-0% versus 12%, 95% CI, 7%-19%; p < 0.001). Among unrevised THAs with minimum 14-year radiographic followup, the mean steady-state linear wear rate for THAs with XLPE liners was lower than the mean linear wear rate for the THAs with CPE liners (0.03 ± 0.05 versus 0.17 ± 0.09 mm/year; mean difference, 0.14; 95% CI, 0.11-0.17; p < 0.001). Osteolysis of any size was noted among 9% (four of 46) of the hips in the XLPE group and 46% (18 of 39) of the hips in the CPE group (odds ratio, 0.19; 95% CI, 0.07-0.51; p < 0.001)., Conclusions: This randomized study with followup into the second decade demonstrated reductions in revision, wear, and osteolysis associated with the use of XLPE. The low wear rates and absence of any mechanical failures among the XLPE liners at long-term followup affirm the durability of these components that did not incorporate antioxidants. Although osteolysis has not been eliminated, it occurs infrequently and has not caused any clinical problems to date., Level of Evidence: Level I, therapeutic study.

Introduction: The purpose of this study was to compare acetabular cup position for 2 cohorts of total hip arthroplasty (THA) patients who had a direct anterior approach., Methods: 100 THA cases were performed with an anterior approach using intraoperative fluoroscopy (IF) to aid in cup positioning. Another group of 100 cases underwent THA with an anterior approach without the use of any fluoroscopy. Postoperative abduction and anteversion angles were measured using Martell's hip analysis software., Results: Mean abduction angle was 43.2° (standard deviation (SD) = 4.5°) for the IF group versus 37.5°(SD = 7.4°) for cases without IF (p<0.001). 18% more cases with IF fell within the Lewinnek safe zone (p<0.001); however, a similar number of cases had over 50° of abduction. The mean anteversion angles of the two groups were also significantly different (IF 21.8° vs. 24.9°) (p<0.01)., Conclusions: There was significantly less variation in cup position among the cases using IF with regards to abduction.

Background: Length of stay after total hip arthroplasty (THA) has decreased over the last two decades. However, published studies that have examined same-day and early discharge protocols after THA have been done in highly selected patient groups operated on by senior surgeons in a nonrandomized fashion without control subjects., Questions/purposes: The purpose of this study was to evaluate and compare patients undergoing THA who are discharged on the same day as the surgery ("outpatient," less than 12-hour stay) with those who are discharged after an overnight hospital stay ("inpatient") with regard to the following outcomes: (1) postoperative pain; (2) perioperative complications and healthcare provider visits (readmission, emergency department or physician office); and (3) relative work effort for the surgeon's office staff., Methods: A prospective, randomized study was conducted at two high-volume adult reconstruction centers between July 2014 and September 2015. Patients who were younger than 75 years of age at surgery, who could ambulate without a walker, who were not on chronic opioids, and whose body mass index was less than 40 kg/m 2 were invited to participate. All patients had a primary THA performed by the direct anterior approach with spinal anesthesia at a hospital facility. Study data were evaluated using an intention-to-treat analysis. A total of 220 patients participated, of whom 112 were randomized to the outpatient group and 108 were randomized to the inpatient group. Of the 112 patients randomized to outpatient surgery, 85 (76%) were discharged as planned. Of the remaining 27 patients, 26 were discharged after one night in the hospital and one was discharged after two nights. Of the 108 patients randomized to inpatient surgery with an overnight hospital stay, 81 (75%) were discharged as planned. Of the remaining 27 patients, 18 met the discharge criteria on the day of their surgery and elected to leave the same day, whereas nine patients stayed two or more nights., Results: On the day of surgery, there was no difference in visual analog scale (VAS) pain among patients who were randomized to discharge on the same day and those who were randomized to remain in the hospital overnight (outpatient 2.8 ± 2.5, inpatient 3.3 ± 2.3, mean difference -0.5, 95% confidence interval [CI], -1.1 to 0.1, p = 0.12). On the first day after surgery, outpatients had higher VAS pain (at home) than inpatients (3.7 ± 2.3 versus 2.8 ± 2.1, mean difference 0.9, 95% CI, 0.3-1.5, p = 0.005). With the numbers available, there was no difference in the number of reoperations, hospital readmissions without reoperation, emergency department visits without hospital readmission, or acute office visits. At 4-week followup, there was no difference in the number of phone calls and emails with the surgeon's office (outpatient: 2.4 ± 1.9, inpatient: 2.4 ± 2.2, mean difference 0, 95% CI, -0.5 to 0.6, p = 0.94)., Conclusions: Outpatient THA can be implemented in a defined patient population without requiring additional work for the surgeon's office. Because 24% (27 of 112) of patients planning to have outpatient surgery were not able to be discharged the same day, facilities to accommodate an overnight stay should be available., Level of Evidence: Level I, therapeutic study.

This study compared the femoral stem revision and loosening rates in primary total hip arthroplasty between 2 different approaches and stem designs. Recent reports comparing the direct anterior approach with either the posterior or lateral approach showed that patients undergoing the direct anterior approach have less pain and an accelerated functional recovery in the early postoperative period. After converting to an anterior approach, the authors observed an increased rate of femoral stem revision. From 2003 to 2009, a posterior or lateral approach was used to insert 514 stems of 2 designs. These cases included the use of an extensively coated cobalt-chrome stem (n=232) or a straight, dual-tapered, proximally porous-coated titanium stem (n=282). In the following years, from 2009 to 2012, 594 short, proximally coated, titanium tapered-wedge stems were inserted through a direct anterior approach. The revision rates of femoral stems inserted through a posterior approach or a lateral approach were compared with those inserted via a direct anterior approach. No stem revisions occurred in the posterior approach group or the lateral approach group, and 5 stems were revised in the anterior approach group for periprosthetic fracture or aseptic loosening (0.8%). Significantly more stem revisions occurred after the use of the new stem design and a direct anterior approach (P=.04)., (Copyright 2016, SLACK Incorporated.)

The application of plasmonics to thermal emitters is generally assisted by absorptive losses in the metal because Kirchhoff's law prescribes that only good absorbers make good thermal emitters. Based on a designed plasmonic crystal and exploiting a slow-wave lattice resonance and spontaneous thermal plasmon emission, we engineer a tungsten-based thermal emitter, fabricated in an industrial CMOS process, and demonstrate its markedly improved practical use in a prototype non-dispersive infrared (NDIR) gas-sensing device. We show that the emission intensity of the thermal emitter at the CO(2) absorption wavelength is enhanced almost 4-fold compared to a standard non-plasmonic emitter, which enables a proportionate increase in the signal-to-noise ratio of the CO(2) gas sensor.

Adverse reaction to metal debris (ARMD) involving the hip joint has emerged as an important reason for failure and revision among patients with metal-on-metal (MOM) hip arthroplasty. To the authors' knowledge, there are no reports of adverse radiographic sequelae in the greater trochanter subsequent to revision for ARMD. The authors describe clinical and radiographic findings in 2 patients who developed greater trochanteric fragmentation 1 to 2 years after conversion of their failed MOM hips to polyethylene bearings. Both patients had solid pseudotumors with tissue necrosis. Several reports describe various clinical features of ARMD. Although poor outcomes have been demonstrated after some MOM revisions, to the authors' knowledge, no reports document greater trochanter fragmentation in ARMD. The current patients highlight the fact that tissue damage occurring with MOM bearing hips can involve bone in addition to soft tissue even after a pseudotumor has been removed and serum metal levels have decreased to normal levels after revision. Unlike the greater trochanteric fractures historically associated with polyethylene wear and osteolysis, no evidence of bone cysts or lesions was found prior to the fractures and neither fracture healed with conservative treatment. For these 2 patients, the authors believe the tissue necrosis included both soft tissue and bone. The necrotic bone resorbed gradually after removal of the MOM bearing, resulting in bone fragmentation with ongoing symptoms. These patients emphasize and remind us that damage is not only limited to soft tissues, but also includes bone. Surgeons should be aware of this radiographic finding and the associated clinical symptoms., (Copyright 2015, SLACK Incorporated.)

Minimally invasive unicondylar arthroplasty (UKA) continues to gain popularity for the management of patients with degenerative arthritis limited to one compartment of the knee. In this study, we examine a series of 517 fixed-bearing, cemented unicompartmental knee components implanted in patients to manage degenerative arthritis in the medial compartment of their knee. All UKAs were performed at a single institution using the same fixed-bearing design. In this study we sought to examine the survivorship of the UKA components and the mechanisms of failure for the knees that were revised. The survivorship and revision rate with this implant were similar to those found in other published reports of fixed-bearing unicompartmental arthroplasties performed through minimally invasive surgical techniques., (© 2014.)

A custom designed microelectromechanical systems (MEMS) micro-hotplate, capable of operating at high temperatures (up to 700 °C), was used to thermo-optically characterize fluorescent temperature-sensitive nanosensors. The nanosensors, 550 nm in diameter, are composed of temperature-sensitive rhodamine B (RhB) fluorophore which was conjugated to an inert silica sol-gel matrix. Temperature-sensitive nanosensors were dispersed and dried across the surface of the MEMS micro-hotplate, which was mounted in the slide holder of a fluorescence confocal microscope. Through electrical control of the MEMS micro-hotplate, temperature induced changes in fluorescence intensity of the nanosensors was measured over a wide temperature range. The fluorescence response of all nanosensors dispersed across the surface of the MEMS device was found to decrease in an exponential manner by 94%, when the temperature was increased from 25 °C to 145 °C. The fluorescence response of all dispersed nanosensors across the whole surface of the MEMS device and individual nanosensors, using line profile analysis, were not statistically different ( p  < 0.05). The MEMS device used for this study could prove to be a reliable, low cost, low power and high temperature micro-hotplate for the thermo-optical characterisation of sub-micron sized particles. The temperature-sensitive nanosensors could find potential application in the measurement of temperature in biological and micro-electrical systems.

Knee wear is commonly measured with the most recent radiograph based on the assumption that wear progresses at a constant rate. Changing patient activity or in vivo polyethylene deterioration are examples of factors that could cause wear rates to change over time. Using six or more radiographs on each of 251 knees over a mean 10-year follow-up, we determined the pattern of polyethylene wear. 92% of knees had linear wear with a mean wear rate of 0.09 ± 0.12 mm/yr. Ten knees (4%) had late accelerated wear. Knees with accelerated wear and those with a wear rate of 0.15 mm/yr or greater had lower survivorship rates. We conclude that wear is linear with rare exceptions and that higher wear is correlated with failure., (Copyright © 2013 Elsevier Inc. All rights reserved.)

Background: During the mid-1990s when our institution was using a press-fit porous-coated cup without supplemental initial fixation for primary THA, the manufacturer transitioned from gamma irradiation to gas plasma for the terminal sterilization of their polyethylene liners., Questions/purposes: At minimum 10-year followup, we asked whether the fixation achieved by solely relying on a press-fit would be durable and how different liner sterilization methods affected radiographic wear, osteolysis, and survivorship., Patients and Methods: We retrospectively reviewed 373 patients who underwent 398 primary THAs with a press-fit porous-coated cup between March 1995 and December 1996. Mean age at time of surgery was 61.5 ± 13.3 years and mean followup was 10.4 ± 3.7 years. We determined reasons for revision, survivorship, femoral head penetration, osteolysis, and wear-related complications., Results: Among 20 revisions involving any component, seven were associated with wear and osteolysis. Kaplan-Meier survivorship, using component revision for any reason as an end point, was 95.7% (95% confidence interval, 93.6%-97.9%) at 10 years. Noncrosslinked liners sterilized with gas plasma demonstrated a mean head penetration rate of 0.20 ± 0.09 mm/year compared with 0.13 ± 0.07 mm/year for liners sterilized with gamma irradiation in air and 0.09 ± 0.04 mm/year for liners sterilized with gamma-irradiation with barrier packaging without oxygen. THAs with increased volumetric wear tended to demonstrate larger osteolytic lesions (r = 0.40) and there tended to be less osteolysis among the liners sterilized with gamma-irradiation with barrier packaging without oxygen. However, there was no difference in survivorship among the sterilization groups and there has been no cup or stem loosening associated with osteolysis., Conclusions: Durable biologic fixation through 10-year followup can be achieved by solely relying on an initial press-fit. Noncrosslinking gas plasma for terminal sterilization of the polyethylene liners was associated with greater head penetration rate than gamma irradiation., Level of Evidence: Level IV, therapeutic study. See Guidelines for Authors for a complete description of levels of evidence.

This paper introduces a novel method for measuring the surface temperature of ultrasound transducer membranes and compares it with two standard measurement techniques. The surface temperature rise was measured as defined in the IEC Standard 60601-2-37. The measurement techniques were (i) thermocouple, (ii) thermal camera and (iii) novel infra-red (IR) "micro-sensor." Peak transducer surface measurements taken with the thermocouple and thermal camera were -3.7 ± 0.7 (95% CI)°C and -4.3 ± 1.8 (95% CI)°C, respectively, within the limits of the IEC Standard. Measurements taken with the novel IR micro-sensor exceeded these limits by 3.3 ± 0.9 (95% CI)°C. The ambiguity between our novel method and the standard techniques could have direct patient safety implications because the IR micro-sensor measurements were beyond set limits. The spatial resolution of the measurement technique is not well defined in the IEC Standard and this has to be taken into consideration when selecting which measurement technique is used to determine the maximum surface temperature., (Copyright © 2011 World Federation for Ultrasound in Medicine & Biology. Published by Elsevier Inc. All rights reserved.)

Because some patients with high wear rates demonstrate extensive osteolysis whereas other patients with similarly high wear rates show little or no evidence of osteolysis, we hypothesized that both polyethylene wear and a patient-specific propensity mediate the development of osteolysis. We evaluated wear and osteolysis using computed tomography and radiographs among 46 patients who had undergone bilateral total hip arthroplasties (THAs). A radiographic patient-specific propensity for osteolysis associated with each THA was quantified by dividing the amount of osteolysis by the volumetric wear. Using a multivariate regression analysis to simultaneously consider the influence of polyethylene wear and patient propensity, we found that both factors are associated with the amount of osteolysis around a THA and that they appear to be of similar importance., (Copyright © 2011. Published by Elsevier Inc.)

For the past 17 years, we have favored treating patients with polyethylene wear and osteolysis by performing a liner exchange with retention of the old shell when possible. Using our institutional database, we identified 187 acetabular revisions in which we had retained the old shell. Among this group, we found 25 rerevisions. These included 10 for hip instability, 9 for cup loosening, 3 for recurrence of excessive wear or osteolysis, 2 for infection, and 1 for dissociation of the replaced liner. The need for rerevision varied with the different retained shell designs. We rerevised 17% of the total hip arthroplasties with old spiked shells, 21% with Arthropor shells, 13% with Triloc shells and 5% with Duraloc shells. Before making a decision to retain or remove a well-fixed old acetabular shell, we recommend consideration of the design's past track record and careful inspection of the condition of the existing shell., (Copyright 2010. Published by Elsevier Inc.)

The highly cross-linked polyethylene liners currently used with modular uncemented cups have substantially decreased wear and osteolysis at early follow-up. However, retroacetabular osteolysis has still been reported in some cases with DePuy Orthopaedic's (Warsaw, IN) second-generation Duraloc acetabular shell. DePuy's third-generation Pinnacle cup incorporates a different shell-liner locking mechanism. We compared the clinical outcome among a matched series of 42 Duraloc and 42 Pinnacle cups at a mean follow-up of 5.9 years. Although the Harris Hip Scores and wear rates were not statistically different between the 2 cup designs, retroacetabular osteolysis behind the central hole was absent among the Pinnacle cups but noted among 19% of the Duraloc cups., (Copyright 2010 Elsevier Inc. All rights reserved.)

Unlabelled: The treatment of asymptomatic osteolysis among well-fixed cementless cups remains controversial. To compare the effectiveness of different treatment strategies, an objective technique for evaluating bone remodeling would be useful. By matching and comparing serial CT images with the aid of a computer-assisted imaging program, we developed a method to evaluate three-dimensional mineralization changes within osteolytic defects. Preoperative, immediate postoperative, and followup CT images were normalized based on a phantom with known densities and matched using image registration so that the same region could be analyzed on each image. New bone mineralization within the preoperative osteolytic lesion volume was quantified based on a patient-specific trabecular bone density threshold. As a pilot study, we applied this technique in 10 patients treated by polyethylene liner exchange with débridement and grafting of periacetabular osteolytic lesions using a calcium sulfate bone graft substitute. Relative to the preoperative osteolytic lesion volume, an average of 43% (range, 8%-72%) of each defect was filled with graft at revision. After resorption of the graft, an average of 24% (range, 9%-44%) of the original defect volume demonstrated evidence of new mineralization at 1-year followup. The amount of new mineralization was directly proportional (r(2) = 0.70) to the defect filling achieved at revision. CT-based image analysis offers an objective method for quantifying three-dimensional bone remodeling and can be used to evaluate the effectiveness of osteolysis treatment strategies., Level of Evidence: Level IV, therapeutic study. See Guidelines for Authors for a complete description of levels of evidence.

We used computed tomography to investigate the 3-dimensional pattern of expansile osteolysis that occurs with a modular cementless acetabular component incorporating a central hole. We measured pelvic osteolysis volume and evaluated how much of the porous-coated surface area was involved with osteolytic defects. Among the 34 total hip arthroplasties we studied, osteolysis almost always originated from the dome hole and typically expanded inferiorly or superiorly without involving the anterior or posterior surfaces of the cup. Larger-volume lesions generally involved greater amounts of the cup surface area, but the cup-lesion interface involvement plateaued at 40% for radiographically stable cups without clinical complications. We hypothesize that the plateauing surface area involvement may explain the absence of cup loosening among these cases despite the presence of large osteolytic lesions.

Unlabelled: The most common method to diagnose and monitor osteolysis is the standard anteroposterior radiograph. Unfortunately, plain radiographs underestimate the incidence and extent of osteolysis. CT scans are more sensitive and accurate but also more expensive and subject patients to more radiation. To determine whether the volume of pelvic osteolysis could be accurately estimated without a CT scan, we evaluated the relationships between CT volume measurements and other variables that may be related to the size of pelvic osteolytic lesions in 78 THAs. Only the area of pelvic osteolysis measured on radiographs, heavy patient activity level, and total volume of wear were associated with the pelvic osteolysis volume measured on CT in the context of the multivariate regression analysis. Despite a strong correlation (r = 0.93, r(2) = 0.87) between these three variables and the volume of pelvic osteolysis measured on CT, estimates of pelvic osteolysis volume deviated from the actual volume measured on CT by more than 10 cm(3) among eight of the 78 THAs in this study. CT images remain our preferred modality when accurate assessments of pelvic osteolysis volume are required., Level of Evidence: Level III, diagnostic study. See Guidelines for Authors for a complete description of levels of evidence.

Rationale and Objectives: Periprosthetic osteolysis is a disease attributed to the body's reaction to fine polyethylene wear debris shed from total hip replacements. The purpose of this preliminary study was to investigate the ability of radiographic texture analysis (RTA) to characterize the trabecular texture patterns on pelvic images for osteolysis and normal total hip arthroplasty (THA) cases., Materials and Methods: Fourier-based and fractal-based texture features were calculated for a database of digitized radiographs from 202 THA cases, 70 of which developed osteolysis. The features were calculated from regions of interest selected at two time points: less than 1 month after surgery, and at the first clinical indication of osteolysis (or randomly selected follow-up time for normal cases). Receiver operating characteristic (ROC) analysis was used to compare feature performance at baseline and follow-up for osteolysis and normal cases., Results: Separation between the RTA features for osteolysis and normal cases was negligible at baseline and increased substantially for the follow-up images. The directional Fourier-based feature provided the best separation with an A(z) value from ROC analysis of 0.75 for the follow-up images, in the task of distinguishing between normal and osteolytic cases., Conclusions: The results from this preliminary analysis indicate that qualitative changes in trabecular patterns from immediately after surgery to the eventual detection of osteolysis correspond to quantitative changes in RTA features. It therefore appears that RTA provides information that could potentially be useful to aid in the detection of this disease.

Periprosthetic osteolysis is one of the most serious long-term problems in total hip arthroplasty. It has been primarily attributed to the body's inflammatory response to submicron polyethylene particles worn from the hip implant, and it leads to bone loss and structural deterioration in the surrounding bone. It was previously demonstrated that radiographic texture analysis (RTA) has the ability to distinguish between osteolysis and normal cases at the time of clinical detection of the disease; however, that analysis did not take into account the changes in texture over time. The goal of this preliminary analysis, however, is to assess the ability of temporal radiographic texture analysis (tRTA) to distinguish between patients who develop osteolysis and normal cases. Two tRTA methods were used in the study: the RTA feature change from baseline at various follow-up intervals and the slope of the best-fit line to the RTA data series. These tRTA methods included Fourier-based and fractal-based features calculated from digitized images of 202 total hip replacement cases, including 70 that developed osteolysis. Results show that separation between the osteolysis and normal groups increased over time for the feature difference method, as the disease progressed, with area under the curve (AUC) values from receiver operating characteristic analysis of 0.65 to 0.72 at 15 years postsurgery. Separation for the slope method was also evident, with AUC values ranging from 0.65 to 0.76 for the task of distinguishing between osteolysis and normal cases. The results suggest that tRTA methods have the ability to measure changes in trabecular structure, and may be useful in the early detection of periprosthetic osteolysis.

This study reviewed the outcome of a single institution's experience with 910 primary total hip arthroplasties using 3 different types of modular, first-generation, hemispheric porous-coated cups. The population included 433 Arthopor, 394 ACS Triloc+, and 83 Harris-Galante components. Among 168 total hip arthroplasties that have undergone acetabular revision, aseptic loosening has occurred in 20 cases. Using liner or cup revision for any reason as an end point, we found that 15-year survivorship was 74.9% +/- 6.2% (95% confidence interval) for the Arthopor cups, 70.1% +/- 7.0% for the ACS Triloc+ components, and 89.3% +/- 10.3% for the Harris-Galante cups (P = .02, log rank). Despite a high incidence of revision for polyethylene wear-related complications and occasional late porous-coating delamination, survivorship using revision for aseptic loosening as an end point exceeded 95% at 15 years for all 3 cup designs.

We reviewed the outcome of 905 femoral revisions performed at our institution between June 1980 and August 2006 using extensively porous-coated, cylindrical stems. A total of 20 femoral rerevisions were identified, including 12 for aseptic loosening, 4 for infection, 3 for stem fracture, and 1 in conjunction with a periprosthetic femur fracture. All stem rerevisions occurred within the first 10 years after surgery. Kaplan-Meier survivorship, using stem rerevision for any reason as an end point, was 97.5% +/- 1.3% (95% confidence intervals) at 5 years, declined to 95.9% +/- 1.9% at 10 years, and remained constant thereafter. With long-term follow-up, extensively porous-coated, cylindrical stems used for femoral revision continue to demonstrate excellent survivorship.

We investigated the role of conventional radiographs and computed tomography scans for the routine followup of total hip arthroplasty patients. Among 92 total hip arthroplasties with a mean followup of 8.5 years, 94 acetabular lesions were detected among 63 hips using computed tomography and 42 of these hips had osteolysis diagnosed on radiograph. Using computed tomography as a gold standard, the sensitivity of anteroposterior pelvic radiographs for the detection of acetabular osteolysis was 67% and the specificity was 72%. Although smaller lesions were more frequently missed, osteolysis was diagnosed on radiograph in 20 of 22 total hip arthroplasties with lesion volumes of at least 10 mL. Because larger osteolytic lesions were generally detected on radiograph, two-dimensional and three-dimensional lesion sizes correlated. However, the limits of agreement for the volume estimates based on the radiograph area were -14.6 to 18.7 mL. Although radiographs can be useful to screen for clinically important pelvic osteolysis, computed tomography images are necessary to accurately measure lesion volumes.