Search

Proton exchange membrane fuel cells (PEMFC) have been noticed by researchers due to their high efficiency, low pollution, and high‐power density in distributed generation systems. In this paper, an LCL‐type grid‐tied PEMFC fuel cell power conditioning system is evaluated in a harmonics‐polluted low‐voltage grid. The LCL‐filters can lead to resonance and instability despite their capability to attenuate harmonics. In this research, a transformer has been used to connect the fuel cell inverter to the grid. The grid‐side inductor of LCL‐filter is realized by the leakage inductance of the transformer. In addition, for more effective resonance damping and attenuation of current ripples caused by the grid voltage harmonics, a capacitor voltage comprehensive feedback control has been designed and investigated. The comprehensive feedback control of the capacitor voltage contains proportional, first and second‐order derivative terms. In the proposed control scheme, the capacitor‐current‐feedback is opposed by the capacitor voltage derivative term due to reverse loop gain, which leads to deleting both of these loop gains. As a result, there is no need to utilize a current sensor in this control method. Consequently, the proportional and second‐order derivative terms of the capacitor voltage attenuate the LCL‐filter resonance. A low‐pass filter is also considered in the second‐order derivative loop in the controllable frequency range to ensure system stability. The simulation results of the PEMFC power conditioning system in different conditions confirm the proper attenuation of LCL resonance of grid‐tied inverter, high‐quality current injection to the harmonics polluted grid, the suitable stability, and the appropriate dynamic response for the proposed system. Under the proposed control scheme, the fuel cell power conditioning system demonstrates satisfactory stability. Even when reducing the LCL filter values by 5%–20%, the system maintains its stability effectively. Moreover, the THD of the injected current into the grid, employing the proposed control strategy, has been successfully reduced to an impressive value of 1.97% in a weak and harmonical grid. [ABSTRACT FROM AUTHOR]

This paper introduces a new structure of a multi-level inverter (MLI) to generate high-level AC voltages using a low number of switches with a quasi-sine waveform. The small number of driver circuits utilised in bidirectional switches is a salient characteristic of this inverter. Also, the number of conducting switches at each voltage level is low in this structure. This results in lower conduction losses of the switches. The proposed topology can be used as the cascaded structure with different approaches to select the value of voltage sources. Power losses are discussed for the proposed structure. To compare the proposed multi-level inverter and demonstrate its superiority, a comparison has been made with some recently presented topologies. According to the comparison results, the advantage of the proposed structure is producing high voltage levels with a smaller number of switches and driver circuits. To prove the suitable performance of the proposed MLI, a 21-level symmetric and 37-level asymmetric inverter containing 14 switches are designed and simulated in the MATLAB/Simulink program. A laboratory prototype for each of these inverters is implemented. The experimental results finely verify the simulations. Besides, an accurate comparison with recently introduced multilevel inverters has been carried out to confirm the effectiveness and superiority of the proposed structure. [ABSTRACT FROM AUTHOR]

This article proposes an enhanced non-isolated high-gain DC-DC converter for interfacing renewable energy sources (RESs). This converter utilizes active switched-inductor (ASL) and switched-capacitor (SC) networks in which the ASL network increases the voltage gain. Furthermore, using the SC network as a multiplier cell helps to reach a high voltage conversion ratio with a proper duty cycle. The main advantages of the proposed converter are the high voltage gain, continuous input current, and low voltage stress on the semiconductor switch and the passive component. Since the voltage stress of the semiconductor element is low, a low ON-state resistance switch is used, which leads to reduced conduction losses. Comprehensive analysis of the steady-state operation in continuous conduction mode (CCM), inductor and capacitor design, and a comparison considering other similar topologies are presented in this article. Also, the parasitic elements are assumed to calculate the DC-Voltage gain and the efficiency of the converter. Finally, simulation results are presented in the PSIM environment to validate the feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

The 2/3-level hybrid inverters are a combination of three-level Neutral Point Clamped (NPC) inverter and conventional two-level inverter, which has the advantage of both two-level and three-level structures with fewer switches than the NPC inverter. In this paper, a new structure of 2/3 hybrid inverter based on dual-Z-‏source network is proposed. The proposed structure improves the performance of the 2/3-level inverter and increases its independent DC input voltages. The output voltage gain can be obtained by selecting the shoot-through interval appropriately in dual Z-source networks. In addition, shoot-through intervals in Z-source networks allow the inverter to run without dead time, thus increasing the output voltage quality. A modified switching method is presented for the proposed inverter, and the necessary calculations are performed. The proposed structure can be used to connect different distributed generation sources to the load separately from the grid or to the low-pressure network. The performed simulations show the accuracy of the proposed structure. [ABSTRACT FROM AUTHOR]

To meet the higher DC link voltage requirement in distributed energy resources (DERs) such as fuel cells (FCs), wind turbines (WTs), and photovoltaic (PV) systems, DC–DC converters are applied. A voltage‐lift (VL) circuit‐based transformer‐less active switched LC‐network (ASLC) converter with a high‐voltage gain is proposed in this paper. Compared to a similar reference converter, the voltage gain of the proposed converter increases efficiently by adding one extra capacitor and diode. The operation of the converter in continuous current mode (CCM) and discontinuous current mode (DCM), the analysis of the steady‐state condition, and comparative analysis with some similar converters are discussed. Moreover, the parasitic elements are assumed to calculate the DC‐voltage gain and the efficiency of the converter accurately. The performance of the proposed step‐up converter is simulated in the PSIM software. A prototype circuit rating of about 20/280 V, 200 W of converter model is designed, and its performance is validated. The experimental outcomes clarify the feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

Multilevel inverters are a new generation of DC–AC converters at medium and high voltage and power levels. In this paper, a new single-phase cascaded multilevel inverter is presented. For this purpose, a new basic cell is presented at first. Then, the new multilevel inverter structure is yielded by series connection of these cells. The proposed new cell is only capable of generating positive voltage levels, and therefore, to produce zero and negative voltage levels, the proposed structure is constructed based on H-bridge module. In order to reduce the maximum blocking voltage especially on H-bridge switches, the cascaded connection of the proposed converter is investigated. A comprehensive comparison is carried out between the proposed multilevel inverter with the classical and recently introduced structures in terms of the number of switching devices, the number of drivers, the total blocking voltage of the switches as well as the loss and efficiency. The accuracy of the proposed inverter's performance is simulated in MATLAB/Simulink in symmetric and asymmetric topologies for a 17-level and 23-level output voltage respectively, and then evaluated by the laboratory prototype. [ABSTRACT FROM AUTHOR]